Vintage Cellars Slimline 800 User Manual
TM
GOLIATH
WineKoolR
400 800
ASSEMBLY & OPERATION MANUAL
READ THE "USE AND CARE GUIDE" BEFORE YOU START
LOCATING YOUR WINE CELLAR
Provide 2
Never locate your wine cellar outdoors or in an area with extremes of temperature and humidity. These units
humid (above 50%R.H.).
Outlet power must be a DEDICATED separately fused, grounded, 15 Amp 110 - 120 V line or 7.5
models (CHECK BOX OR SERIAL NUMBER LABEL ON UNIT FOR YOUR LINE VOLTAGE REQUIREMENTS).
Koolr Products Inc. will not be liable or responsible for incidental or consequential damages. (See Warranty).
Place unit in a clean area and allow access to the exterior surfaces for periodic vacuuming of the condenser coil.
(See troubleshooting for details.)
1/2
minimum 4” for the top.
Amp - for 240 V
Clean using a damp cloth and no detergents or polishes under any circumstances.
Always remove all bottles before relocating your wine cellar.
AREA FOR ASSEMBLING YOUR WINE CELLAR
TOOLS
Rubber mallet, hex wrench (included), phillips screwdriver.
Helper is needed.
TEST THE COOLING UNIT
Plug it in on a table top, to verify that controls and display are functional, and that the unit is producing cool air
after a few minutes of operation.
Note that the electronic controller has a one-minute safety delay between initial plug-in and start-up of the
compressor.
BEFORE YOU START !
of the unit or on the light cord.
~ 2 ~
TOP
LEFT
REAR
HARDWARE
x 1
HINGES
x 2
CONNECTOR PLATES
TOP
RIGHT
REAR
x 1
VENT
x 2
x 4
A
Hinge Washer x 3
C
Cooling Unit Bolts
in cooling unit box
E
Hooks
x 2
x 1
F
Power supply
x 1
B
Legs x 10
D
Allen key
in cooling unit box
x 1
Left optional
G,H,I - Slimline ONLY
G
Wall Ties
x 2
G
H
x 2
Anchors
x 2
I
Screws
x 2
Brace
x 8
Handle and Lock
x 3
SPACER
~ 3 ~
Spacer
x 2
Shelves
x 40
1
PLACE 2 BACKS (WITHOUT CUT-OUT) AGAINST WALL
INSERT CORNER (LEFT ONLY)
INSERT CORNER (RIGHT ONLY)
Step 1:
WALL
Note:
Disregard
Back RIGHT marking
LEFT
(INSERT)
Step 2:
In this MODEL we use
a panel marked
“BACK RIGHT”
for the “LEFT” side
BACK
This label is correct
use panel for
“RIGHT” side
BACK
PLACE AGAINST WALL
PLACE
BACK
AGAINST
W
ALL
FLOOR
WALL
INSERT
RIGHT
(INSERT)
BACK
~ 4 ~
FLOOR
TIP
WALL
FLOOR
2
BACK
PLACE AGAINST WALL
BACK
WALL
BACK
FLOOR
WALL
BACK
INSERT POSTS 1 INTO BACK WITH CUT-OUT
INSERT BACKS WITH CORNERS INTO POSTS
POST 1
POST 1
BACK
~ 5 ~
PLACE AGAINST
BACK
WALL
BACK
BACK
LEFT
LEFT
RIGHT
LEFT
3
LEVEL
SPACER
SPACER
LIFT
Place SPACERS to get
LIFT
ready to insert BOTTOM
SPACER
~ 6 ~
4
SPACER
BOTTOM
OUTSIDE
BACK
INSTALL BOTT
BOT
T
OM
OM
2. REST BOTTOM ON SPACERS
PRESS
SPACER
4. PULL OUT
SPACERS
BOT
T
SPACER
SPACER
OM
OK
NO
PRESS
~ 7 ~
BOT
T
OM
INSTALL BOTTOM CONNECTOR PLATES
LEGS
BOTTOM
5
TAP IN CONNECTORS TIGHTLY (NO GAP) WITH CLOSED HAND OR RUBBER MALLET
Note:
DOORS are reversible. ! Install HINGES based on your preference ! Left hinging is shown.
- LEFT
HINGING:
shown in
STEP 1
- RIGHT
HINGING:
not shown
HAND PRESS IN ALL CONNECTOR PLATES IN BOTTOM
HINGE 2
HINGE 4
HINGE 4
RIGHT
STEP 1:
HINGE 2
BOTTOM
LEFT
REAR
LEFT
HINGE 3
HINGE 3
HINGE 1
NO GAP!
HINGE 4
BOTTOM
CENTER
FRONT
HINGE 4
CENTER
B
REAR
CENTER
BOTTOM
RIGHT
FRONT
STEP 2:
SCREW IN ALL 10 LEGS
B
LEAVE 1/4” SPACING ON CORNER LEGS
LEAVE 1/2” SPACING ON CENTER LEGS
REAR
B
Limited access in upright position !
~ 8 ~
TAP
GENT
BOTTOM
RIGHT
REAR
L
Y
Loading...