Vinotemp EL300COMML User Manual

Page 1
A PROUD HERITAGE OF EXPERIENCE & QUALITY
SINGLE- Zone Wine COOLER
EL-300COMM (APROX 188 BOTTLES)
WWW.VINOTEMP.COM
Page 2
Page 3
Yo u r W i ne C el l ar
This unit can be used for storage and/or service. The unit has a glass door and soft interior light that you can use to display your wine.
Se r v ing Wi ne s
Storing wines at the proper temperature is important. To preserve them as long as possible wine should be stored at approximately 55° Fahrenheit. However, the chart below suggests the optimal drinking temperature for the different styles of wine.
°C °F Wine Style
19 66 Armagnac, Brandy, Cognac
18 64 Full Bodied Red Wines, Shiraz
17 62 Tawny Port
15 59 Medium Bodied Red Wines
14 57 Amontillado Sherry
13 55 Light Bodied Red Wines
12 54 Full Bodied White Wines
11 52 Medium Bodied White Wines
10 50 Rosé, Light Bodied White Wines
9 48 Vintage Sparkling
8 46 Fino Sherry
7 45 Non Vintage Sparkling
17621 South Susana Road, Rancho Dominguez, California 90221
1
3
Page 4
General Operating Instructions
READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE
-Save these instructions-
Register your warranty within 10 days of receiving the unit.
Remove all external and internal packaging from your appliance. Be sure that all parts have been included before discarding any packaging materials. You may want to keep the box and packing materials for use at a later date.
Upon receipt and inspection of unit, the supply cord must be replaced if it is damaged. Contact our customer service at 1-800-777-8466 or [email protected].
Let the unit rest UNPLUGGED for 24 hours once you have it placed in
your home.
To register your product, visit:
http://www.vinotemp.com/Warranty.aspx
Please be sure to retain your proof of purchase.
4
Protect Your Investment with an Extended Warranty!
Add a New Leaf extended warranty to your order, and have the security of knowing that if there should
be a problem, even years in the future, New Leaf will be there to assist! Usable for any Wine Cellar or
other electronic device manufactured by Vinotemp. Add this warranty to purchases made from
vinotemp.com or other qualified venders. Warranty must be registered within the first 10 days from
original purchase.
Visit www.Vinotemp.com to purchase.
WWW.VINO TEMP.CO M
Page 5
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS
ELECTRICAL CONNECTION
PARTS AND SPECIFICATIONS
BOTTLE CAPACITY
INSTALLATION
OPERATING YOUR WINE COOLER
CARE AND MAINTENANCE
TROUBLESHOOTING
TERMS OF SALE AND WARRANTY
SERVICE & IMPORTANT NOTICE
...............................................................................................................9....
....................................................................................................................10
.......................................................................................................
............................................................................................
......................................................................................
...........................................................................
...........................................................................................
...........................................................................
..............................................................................
.......................................................................
6
7
8
11
13
14
15
19
17621 South Susana Road, Rancho Dominguez, California 90221
5
Page 6
IMPORTANT SAFETY INSTRUCTIONS
To reduce the risk of fire, electrical shock or injury when using your appliance, follow these basic precautions:
• Do not operate this or any other appliance with a damaged cord.
• Do not operate if housing is removed or damaged.
• Exercise caution and use reasonable supervision when appliance is used near children. Never allow
children to operate, play with or crawl inside the appliance. Keep packing materials away from children.
• Before performing any maintenance or cleaning, ensure that the unit is unplugged or that the power line is disconnected.
• Do not clean appliance with flammable fluids. Do not store or use gasoline or other fl and liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.
• Exercise caution when moving and installing the unit. The cooler is heavy and may require two or more people when moving the unit to prevent strain or injury.
• To ensure proper ventilation for your appliance, the front of the unit must be completely unobstructed. Choose a well-ventilated area with temperatures above 60°F and below 90°F.
• Locate the unit away from direct sunlight and sources of heat (stove, intended for indoor use only and must be installed in an area protected from the elements.
• Place the appliance on a solid, level surface.
• Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in
this manual. All other servicing should be referred to a qualified technician.
• Connect to properly polarized outlets only. It is recommended that a separate circuit, serving only your appliance be provided. Use receptacles that cannot be turned off by a switch the plug is fully inserted into the receptacle.
• To protect against electric shock, do not immerse appliance, plug or cord in water or other liquids. Avoid locating the unit in moist areas.
• This appliance is designed to be built-in (fully-recessed) or freestanding.
• Do not use this appliance for other than its intended purpose. For indoor, household use only.
• Do not operate the unit with wet hands, while standing on a wet surface or while standing in water.
• Do not use so
damage or discolor the interior.
• Keep fingers out of pinch point areas and be careful when closing doors if children are around.
• This appliance is designed for storing and cooling wines. Do not store perishable food or medical
products within the unit.
• When disposing of refrigerated appliances, special handling is often required. It is the consumer’s responsibility to comply with federal and local regulations when disposing of this p
• Do not slide your wine cooler into place.
• WARNING: Risk of child entrapment and suffocation. Before you throw away this or an old unit, take off
the door. Leave the shelves in place, so that children may not easily climb inside.
Caution:flammable refrigerant used! When handing,moving and use of the refrigerator,make sure
•
to avoid either damaging the refrigerant tubing,or in creasing the risk of a leak.
lvent-based cleaning agents or abrasives on the interior of the cooler. These cleaners may
heater, radiator, etc).This unit is
or pull chain. Be sure that
ammable vapors
roduct.
6
WWW.VINO TEMP.CO M
Page 7
ELECTRICAL CONNECTION
Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, frayed or shows cracks or abrasions across its length, have it replaced at an authorized service center.
For your protection, this unit is equipped with a 3-conductor cord set that has a molded 3-prong grounding­type plug, and should be used in combination with a properly connected grounding-type outlet.
• Do not under any circumstances cut or remove the third ground prong from the power cord supplied. For personal safety, this appliance must be properly grounded.
• The cord should be secured behind the unit and not left exposed or dangling to prevent accidental injury.
• A standard electrical supply (115V AC only, 60Hz, 15A), properly grounded in accordance with the National Electrical Code and local codes and ordinances, is required.
• Never unplug the unit by pulling the power cord. To disconnect the appliance, always grip the plug firmly and pull straight out from the wall outlet. When moving the unit, be careful not to damage the power cord.
• The unit should always be plugged into its own individual electrical outlet with a voltage rating that matches the rating label on the unit.
Extension Cord
CAUTION: It is strongly recommended that you do not use an adapter
or an extension cord with this unit.
17621 South Susana Road, Rancho Dominguez, California 90221
7
Page 8
PARTS AND SPECIFICATIONS
①Stainless Steel Door
②Cabinet
③Stainless Steel Handle
④Tempered Glass Door
⑤Return-airway
⑥Control Panel
⑦Fan (Upper Chamber)
⑧Shelves
⑨Lock
⑩Ventilator
11Leveling legs
Model No.
Voltage
Frequency
Ambient Temperature Range
Control Temperature Range
Refrigerant
Power Consumption
Input Power
Volume
Net Weight
Gross Weight
Dimensions (W x D x H)
Box Dimensions (W x D x H)
*Note: bottle storage capacity is based on a standard 750 ml wine bottle. Storing large and/or oddly shaped bottles (including champagne and sparkling wine bottles) will decrease the bottle capacity of the wine cooler.
EL-300COMM
EL-300COMM
AC 115V
60 Hz
41
-100 / Humidity
℉
45~90%
41-64
℉
a/1.69 oz.
R
600
1.39 kWh/24h
W
200
21.2 cu. ft
282 lbs
298 lbs
29.5 in x 27.1 in x 7 in
30.9 in x 29.1 in x 75.6 in
4
8
WWW.VINO TEMP.CO M
Page 9
VINOTEMP EL-300COMM SINGLE-ZONE WINE COOL ER
BOTTLE CAPACITY
You may adjust the shelves of your wine cooler to accommodate more or less bottles.
If stacking bottles 2-3 high, please do not pull out the shelves.
Adjust the shelves as shown to fit approximately 188 bottles in your cooler
17621 South Susana Road, Rancho Dominguez, California 90221
9
Page 10
INSTALLATION
• Remove all packing material before using your wine cooler.
• IMPORTANT: Before connecting the unit to a power source, let it stand upright for approximately 24
hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.
• Clean the interior surface with lukewarm water and a soft cloth.
• This unit is designed for freestanding or built in installation but indoor use only. Position the unit in a dry
and well-ventilated place. Avoid placing the wine cooler near any source of heat or moisture, or in direct sunlight. Do NOT install the unit in a location with an ambient temperature that will fall below 60°F.
• For built-in installation, leave a ¼” (6.35mm) space on each side and at the top of the wine cooler to ensure proper air circulation to cool the compressor and condenser. Also, be sure to not obstruct the front exhaust vent with any objects as this may affect the unit from performing properly.
• For freestanding installation, 6” of space at the back, 10-12” of space on each side, and unlimited clearance at the top of the wine cooler are suggested to ensure proper air circulation to cool the compressor and condenser. Do not place underneath a table, counter top, or anything of the sort as this will not allow for proper air circulation.
• Do not slide the unit into place.
• Place the wine cooler on a level surface strong enough to support it when it is fully loaded. To level the
wine cooler, adjust the front leveling legs at the bottom of the wine cooler.
• For best performance it is recommended that you install the appliance in a location with an ambient temperature between 41°-100°F. If the ambient temperature is above or below recommended temperatures, the performance of the unit may be affected.
• Plug the wine cooler into an exclusive, properly installed-grounded wall outlet.
INSTALLING THE STAINLESS STEEL HANDLE
This wine cellar includes a stainless steel handle that is not required to operate this unit. To install the handle please follow the below instructions:
• Pull away the door gasket in the area where
the handle is to be installed - you can see two designated holes for handle installation. The gasket is easily displaced by hand, no tools are necessary.
• Install the handle tightly as shown below with
the two screws, lock washers and flat washers provided. (DO NOT over tighten as this will cause damage to the handle assembly and stainless steel surface of glass door).
• Replace the door gasket to its original position.
10
WWW.VINO TEMP.CO M
Page 11
Operating Your Wine Cooler
When you use the wine cooler for the first time or restart the wine cooler after
If the unit is unplugged, power lost, or turned off, you must wait 3 to 5 minutes
1 Up
2 Temperature Display
3
℃/℉
Display
4 Down
5 Set temperature
The Wine cooler should be placed in a position where the ambient temperature is between 12-38℃/54-100℉. Humidity level is between 45~90%. If the position is above or below this range, the performance of the unit may be affected. For example, placing your unit in extreme cod or hot conditions may cause interior temperature to fluctuate.
NOTE:
having been shut off for a long time, there could be a few degrees variance between the temperature you select and the one indicated on the LED readout . This is normal and it is due to the length of the activation time. Once the wine cooler is running for a few hours everything will be back to normal.
before restarting the unit. If you attempt to restart before this time delay, the wine cooler will not start.
The controls of your wine cooler
Used to raise (warm)the set temperature by 1℃or 1℉.
Used to lower (cool) the set temperature by 1℃or 1℉.
17621 South Susana Road, Rancho Dominguez, California 90221
11
Page 12
press this bottom, press to set temperature. To view the “set”
6 ℉/℃ Selector
7 Power
The temperature that you desire to set will increase 1℃or 1℉if you touch the
Temperature range : 5-18℃/41-64
℉
The temperature inside the unit will be appeared in blue color in the display
To prevent damaging the door gasket, make sure the door is fully open when
For easy access to the bottles stored, pull the shelves out approximately 1/3.The
The shelves has been designed so that a range of shelf height can be selected. All
temperature at any time, touch the UP or DOWN mark, the “set” temperature will temporarily “flash” in the LED display for 5 seconds.
Select the temperature display setting in Fahrenheit or Celsius degree.
To control the appliance turn on/off. To turn off the appliance, touch the mark and
hold for at least 5 seconds. Press
again, turn on the appliance. The LED readout will show the original temperature set previously when restart the appliance or reconnect after power cuts .
Setting the Temperature Control
You can select temperature display setting from Fahrenheit to Celsius degree b touching the℃/℉Selector mark. Fahrenheit or Celsius degrees indicator will appear in blue color in the temperature display window for each zone. You can set the temperature as you desire by touching the UP and DOWN marks. When you touch the
two marks for the first time, the LED readout will show the original temperature set previously.
UP mark once, on the contrary the temperature will decrease 1℃or 1℉if you touch the DOWN mark once.
12
window.
Shelves
pulling shelves out of the rail compartment.
shelves are designed with an emergency stop to prevent the being removed too far when loaded.
the shelves can be adjusted.
.
TEMP.CO M
WWW.VINO TEMP.CO M
Page 13
DOOR LOCK
The wine cooler comes with a lock and key combination. The keys are located inside the pl astic bag containing the Owner’s Manual. To unlock the door, insert the key into the lock and turn it counter -clockwise. To lock the door, insert the key and turn it clockwise, ensuring that the metal pin is fully engaged.
DEFROSTING
The wine cooler defrosts automatically. The evaporator behind the rear wall of the unit automatically defrosts and the condensate collects in the drainage channel behind the rear wall of the unit, and flows through the drainage hole into the drip tr
ay by the compressor, where it evaporates.
CARE AND MAINTENANCE
CLEANING YOUR WINE COOLER
IMPORTANT: Always unplug the unit before cleaning or performing maintenance. Never use harsh cleansers or scouring pads to clean any part of the unit.
• Turn off the power, unplug the appliance, and remove all items including shelves.
• Wash the inside surfaces with a warm water and baking soda solution. The solution should be about 2
tablespoons of baking soda to a quart of water.
• Wash the shelves with a mild detergent solution.
• Wring excess wate
• Wash the outside cabinet with warm water and mild liquid detergent. Rinse well and wipe dry with a
clean soft cloth.
POWER FAILURE
Most power failures are corrected within a few hours and should not affect the temperature of your appliance. If the power is off for an extended period of time, proper steps should be taken to protect your contents.
INACTIVITY
If the unit will not be used for a period of less than three weeks, leave the cooler operating. If the period of inactivi Leave the door open slightly to prevent any possible moisture build-up.
ty is several months, remove all items and turn the unit off. Clean and dry the interior thoroughly.
MOVING YOUR WINE COOLER
Before moving your wine cooler, first be sure to remove all items from the cooler.
• Securely tape down any loose items, such as shelves, inside the unit.
• Turn the adjustable leg up to the base to avoid damage.
• Tape the door shut.
• Ensure that the unit stays securely in the upright position during transportation. Protect the outside of
the appliance
ENERGY SAVING TIPS
• The unit should be located in the coolest area of the room away from heat sources or direct sunlight.
• Ensure that the unit has proper allowances on all sides for proper ventilation. Never cover any air
vents.
• Only open the cooler door for as long as necessary. Frequent opening of the door will affect internal temperature.
r out of the sponge or cloth before cleaning control panels or any electrical parts.
with a blanket or similar item.
17621 South Susana Road, Rancho Dominguez, California 90221
13
Page 14
PROBLEMS WITH YOUR WINE COOLER
Most common problems can be solved easily, saving you the cost of a possible service call. Try the following suggestions to see if you can solve the problem before contacting Vinotemp at [email protected].
TROUBLESHOOTING
PROBLEM POSSIBLE CAUSE
Wine Cooler does not operate
• Ensure unit is plugged into an electrical outlet.
• Check if unit is turned off.
• Check for a tripped circuit breaker or blown fuse.
Wine Cooler is not cold enough
Wine Cooler turns on and off frequently
Wine Cooler light does not work
Wine Cooler makes too much noise or vibrates
Wine Cooler door will not close properly
• Check the temperature control setting.
• External environment or ambient temperature may require a higher
setting.
• Check if door does not close completely or is open too often.
• Check if door gasket does not seal properly.
• The room temperature may be hotter than normal.
• Check if door does not close completely or is open too often.
• Check if door gasket does not seal properly.
• The temperature control is not set correctly.
• Ensure unit is properly plugged in.
• Check for a tripped circuit breaker or blown fuse.
• Check if the light switch is OFF.
• Check to ensure the unit is level.
• The rattling noise may come from the flow of refrigerant. This is
normal.
• As each cycle ends, you may hear gurgling sounds caused by the flow of refrigerant in the unit. This is normal.
• Contraction and expansion of the inside walls may cause popping and crackling noises.
• Check to ensure the unit is level.
• The door was reversed and was not properly installed.
• The gasket is dirty.
• The shelves are out of position.
14
.
TEMP.CO M
WWW.VINO TEMP.CO M
Page 15
Terms of Sale
Vinotemp International Corp. (“Seller”) and the person or entity that acquires these goods from
Seller (“Purchaser”) hereby fully agree to the following terms and conditions of the sale:
Shipping fees are the responsibility of the Purchaser whether freight prepaid or freight collect.
Seller assumes responsibility for the goods sold to the Purchaser until the goods have reached
Purchaser’s delivery address (FOB Destination) and the delivery receipt is signed clear. Seller
is not responsible for the carrier’s late delivery, missed delivery, unpaved roads, remote
locations, stairs, elevators, narrow door openings and other such issues in attempting to fit or
deliver the goods into the Purchaser’s location. Delivery to remote locations may require
additional fees. Remote location may be defined at the discretion of the carrier as more or less
than 50 miles from the nearest major city. Purchaser assumes all responsibility for additional
costs related to freight such as access, measurement, installation, hook-up, wiring, moving
and storage of the goods, flight of stairs, carrier’s inability to safely and/or adequately deliver,
inability to use the building elevator to lift the goods, narrow openings, along with any
additional costs to deliver or redeliver the product properly. Make sure to review access to
the property and size of the product ordered. The transportation of all goods is subject to the
terms and conditions which the carrier imposes on Purchaser. Installation is the responsibility
of the Purchaser. If white glove delivery was ordered and cannot be performed properly, or
access is hindered in any way, Purchaser agrees to accept delivery curbside. If Purchaser will
calls or pays for their own freight responsibility transfers to the Purchaser when the Purchaser
or Purchasers freight company picks up the unit from Seller.
White Glove Delivery: White glove delivery is defined as follows: Delivery will be to the 1st
floor only, easy access and NO STAIRS, Doors aligned, feet attached (if necessary) and
removal of packaging. Customer agrees that any additional request will result in additional
charges. White glove delivery is not included for returns or Non-New Units.
Note: Shipping and handling fees for products over 300lbs are for threshold delivery.
White glove delivery is available by request for an additional fee. Freight discussed is
Continental USA (excluding Alaska), cost is additional please email us at [email protected]
quote.
for a
All damages must be noted at time of delivery. If a bill is signed that there is no damage, buyer
accepts delivery as free and clear. Any claim for damages of the goods, when FOB
Destination, that incurred during shipment by the carrier are insured and handled directly with
the carrier by the Seller if noted on the receipt and notified within 48 hours of delivery. OPEN
AND INSPECT YOUR DELIVERY. When FOB Destination, if the item is damaged by the
freight company, and Purchaser cancels rather than accepts a replacement, the order can be
cancelled by paying for freight costs both ways and a 35% restocking fee for stocked items. No
cancellation or refunds on custom/made or made to order products. When shipped 3rd Party
(FOB Warehouse), Purchaser assumes all responsibility for delivery, payment of freight and
freight claims for damages during shipment. Manufacture defects will be handled directly with
Seller, subject to the limited warranty below.
17621 South Susana Road, Rancho Dominguez, California 90221
15
Page 16
All sales are final. Unless authorized in writing by the Seller, Purchaser may not return the
goods under any circumstance. If Seller agrees in writing to take back stocked goods, there
will be a restocking/service fee that is 35% of the purchase price of the goods and freight both
ways (product must be new, unused, and in original packaging). If Purchaser returns goods
claiming that the goods are defective and goods are found to be in working condition by the
Seller, Purchaser is liable for the cost of freight both ways plus and a service fee that is 35% of
the purchase price of the goods. Built-to-Order and Custom products are non-returnable,
non-refundable. Purchaser must notify Seller of non-conforming goods within 48 hours of
receipt, after which time all goods are deemed accepted by the Purchaser. If an order has
been placed and production has not started, cancellation of your order will be a 15% charge. If
Purchaser tenders payment with a check that has insufficient funds (NSF), a collection fee plus
NSF fee of $50 will be added to the invoice, which Purchaser agrees to pay promptly. If
Purchaser puts a stop payment on a check or credit card for any reason, Purchaser agrees to
pay for all costs associated with the Seller’s collection or litigation of such a claim, including,
without limitation, general and special damages, court costs and attorneys’ fees. Finance
charges begin the date of invoice. Title to the goods reverts back to the Seller in the case of
non-payment of goods or services. All fees and costs to retrieve the product, cost of freight,
legal costs, collection fees and court fees, credit card fees and interest rate of 18% (annual
rate) will be the responsibility of the Purchaser. In a credit card dispute, Purchaser assumes
and must immediately pay any “credit card arbitration” fees and chargeback fees which the
credit card companies charge at the time of the chargeback. Any disputes not resolved within
30 days from the invoice date will be reported to credit reporting agencies.
LIMITED WARRANTY: Seller warrants that the goods will be free of defects in materials and
workmanship as follows:
Furniture style (wood) wine cabinets made in the U.S.: all cooling unit parts only for a period of 5 (five)
years; cabinetry and labor (uninstalled) for a period of 12 (twelve) months.
Metal cabinet wine units: parts and labor for cooling system and cabinetry for a period of 12 (twelve)
months.
For Designer Series units: parts and labor for a period of 12 (twelve) months from date of sale,
compressor parts 5 years.
Thermoelectric Units: 90 (ninety) days (including Wine Coolers, Beer Dispensers, Humidor,
Portofino Wood Cellars, and Refrigerators).
Wine-Mate Split and Ducted Systems and other installed cooling units are parts only for 1 year, no
labor. Self Contained Wine-Mate Cooling Systems are 5 years parts, 1 year labor. Removal and
reinstallation of cooling units is not included.
Wine Accessories, Racking Systems, Parts and Other miscellaneous items is a 30 day warranty.
Il Romanzo units: Warranty 90 (ninety) days. Replacement part 12 (twelve) months from the date of
sale.
16
Non-New Units (Scratch & Dent/Refurbished/Floor Models), warranty for compressor units is 90 days
.
TEMP.CO M
WWW.VINO TEMP.CO M
Page 17
from your dated invoice and 30 days for thermoelectric units (parts for function only, not cosmetic
defects). These units are refurbished and sold as is; Purchaser assumes risks to the quality and
performance of goods and assumes the costs of all necessary service or repair not covered herein.
Extended warranties via New Leaf may not be purchased on Non-New Units. Delivery is curbside.
Upgrades in delivery will require an additional fee.
Element Grills (via Element Products LLC), grills have a 1 year parts warranty and a thirty day limited
parts warranty on grill accessories.
If a purchaser claims a product is “defective” with regards to refrigeration, Purchaser must obtain a
letter from a qualified refrigeration technician at the Purchaser’s cost to verify that the unit was
installed properly, with proper ventilation and the unit is truly malfunctioning due to a manufacturing
defect.
Removal or re-installation of a unit is not included in warranted costs. Purchaser’s exclusive remedy is
limited at Seller’s option to repair or replace defective part[s] with either new or reconditioned part[s].
Purchaser is responsible for shipping the unit pre-paid to a designated facility and Seller will pay
return shipping charges in the continental United States for items repaired under warranty within 12
(twelve) months from date of sale. The returned unit must be packaged correctly, with enough
protection to ensure the unit is not further damaged. Oversized or lack of packaging is not permitted
and will be refused. Replacement or exchanged units will be returned to Purchaser through curbside
delivery only. Any redelivery fees are the Purchasers responsibility.
Since the natural variation in texture, density, grain, color, tone, and shade of wood is unavoidable;
Seller does not guarantee the texture, color, tone, or shade of the wood: nor does seller guarantee the
colorfastness of wood or against peeling, chipping, cracking, or scratching. Note: Unfinished wood is
subject to warping; all wood surfaces must be sealed before placing cellar into service. Make sure
doors are aligned by reviewing the owner’s manual. Improper repair or placement of the unit will void
the warranty. Any third party repair facility must be pre-approved in writing by Seller, before providing
replacement parts under warranty.
Storage Fees: When having an item serviced by a Vinotemp service technician at the Vinotemp
facility, Purchaser agrees to pick up their repaired item or make arrangements for return shipping
within a 60-day period once they have been notified by Vinotemp through phone call, email, or letter
that their unit is ready for pick up. If the item remains in the Vinotemp warehouse after 60 days but no
longer than 120 days, the Purchaser will incur additional storage fees of 2%. After 120 days in
storage, the item will become property of Vinotemp. Warranty period is from the date of sale (not from
shipping, delivery, nor installation).
All completed cabinetry, racking, or other custom work must be picked up or shipped within a period of
14 days after Vinotemp has notified the Purchaser by phone call, email, or letter. Any completed
cabinetry, racking, or other custom work stored longer than 14 days will incur an additional storage
fee. After 120 days, the product will become property of Vinotemp.
This Limited Warranty does not cover damage due to such things as accident, misuse, abuse,
mishandling, neglect, acts of God, fires, earthquakes, floods, high winds, government, war, riot or
labor trouble, strikes, lockouts, delay of carrier, unauthorized repair, or any other cause beyond the
17621 South Susana Road, Rancho Dominguez, California 90221
17
Page 18
control of the Seller, whether similar or dissimilar to the foregoing. Seller is not responsible for any
damages caused to Purchaser's property resulting from the goods. This limited warranty applies only
inside the Continental US (Alaska, Puerto Rico, Hawaii and other territories/countries are not
warranted).
Purchaser understands and acknowledges that the goods sold here are wine cellars, cigar humidors,
and/or other similar units which house wine or cigars or other items. Purchaser assumes all risk of
using these units, including risk of spoilage, humidity variations, temperature variations, leaks, fire,
water damage, mold, mildew, dryness and similar and any other perils that might occur.
Seller is not responsible for incidental or consequential damages, and there are no warranties,
expressed or implied, which extend beyond the Limited Warranty described above. Warranty and
liability are non-transferable. The implied warranties of merchantability and of fitness for a particular
purpose are hereby expressly disclaimed. Some states do not allow the exclusion of incidental or
consequential damages, or a waiver of the implied warranties of fitness and/or merchantability, so the
above limitations may not apply to you. This warranty gives you specific legal rights and you may also
have other rights which vary from state to state. Seller disclaims any indemnification for claims of
infringement of any intellectual property of protectable nature. In the event of any dispute between
Seller and Purchaser arising out of or relating to these terms and conditions or to the goods sold
generally, Purchaser must first file a written claim with Seller within ten days of the occurrence giving
rise to the claim and wait an additional thirty days for a response before initiating any legal action. The
sale and all terms are subject to California law. Any legal proceeding arising out of or relating to these
terms and conditions or to the goods sold Purchaser shall bring, solely and exclusively in the County
of Los Angeles. In no event may Purchaser initiate any legal proceeding more than six months after
the occurrence of the event giving rise to the dispute. Seller may make non-payment claims until debt
is paid in full.
Any dispute or claim relating in any way to these to the Terms and Conditions, the Website, or any
products or services sold or distributed by or through this Website, store, or catalog will be resolved by
binding arbitration, rather than in court, except that you may assert claims in small claims court if your
claims qualify. The Federal Arbitration Act and federal arbitration law apply to the Terms and
Conditions. We each agree that any dispute resolution proceedings will be conducted only on an
individual basis and not in a class, consolidated or representative action. If for any reason a claim
proceeds in court rather than in arbitration we each waive any right to a jury trial. We also both agree
that you or we may bring suit in court to enjoin infringement or other misuse of intellectual property
rights.
The above terms and conditions are the only ones governing this transaction and Seller makes no
oral representations of any kind. These Terms and Conditions can only be modified in writing, signed
by both Purchaser and Seller.
08.29.16
.
18
TEMP.CO M
WWW.VINO TEMP.CO M
Page 19
SERVICE & IMPORTANT NOTICE
Upon receipt and inspection of unit, the supply cord must be replaced if it is damaged. Contact our customer service at 1-800-777-8466 or [email protected].
The manufacturer has a policy of continuous improvement on its products and reserves the right to change materials and specifications without notice.
WARNING:
Please do not place the unit within reach of children.
For adult use only.
Contact [email protected] with any questions or visit
www.vinotemp.com
17621 S. Susana Road
Rancho Dominguez, CA 90221
www.vinotemp.com
Vinotemp is a registered trademark of Vinotemp International. All products, features, and services are subject to change without notice. We cannot guarantee the accuracy of the contents of this document. We disclaim liability for errors, omissions, or future changes.
© 2016 Vinotemp International. All rights reserved.
Loading...