Vimar Eikon, Arké, Plana Installer Manual
Installer manual
Eikon
20508
Arké
19508
Plana
14508
BUS EnOcean interface - 2 modules
Instructions
This manual is necessary in order to configure the radio-frequency devices when used with
the By-me automation system through the specific Bus interface with the EnOcean module
20508-19508-14508.
WARNING:
• The Bus interface 20508-19508-14508 is compatible with control unit 21509 ver. 3.00
and later.
• The actuator 01796.1 is compatible with control unit 21509 ver. 5.04 and later.
• The devices are compatibles with EasyTool Professional Software ver. 2.11 and later.
2
Bus interface with EnOcean module
Bus interface with EnOcean module
The Bus with EnOcean module interface allows using the radio frequency devices to extend coverage in places or accesses where it
is not possible to add any cables and devices via Bus.
The interface permits integrating the By-me system and the radio-frequency devices with the EnOcean module that allow carrying out
all the automation functions such as, for instance, controlling lights and shades, scenes, etc.
The interface manages all these functions via pairs of configurable radio buttons such as rocker switches, dimmer switches, roller shade
and scene controls and radio relay actuators.
It is supplied in the following versions:
20508: 2 Eikon modules
19508: 2 Arkè modules
14508: 2 Plana modules
Eikon
Arké
Plana
Technical characteristics
• Rated supply voltage (Vn): BUS 20-30 V d.c.
• Protection class: IP30
• Operating temperature: -5 - +45 °C (for indoor use)
• Installation: flush or surface mounting
• Consumption: 20 mA typ
• Frequency of reception and transmission: 868 MHz
• Configuration button
• Indicator LED
• It has two terminals for the polarized connection to the Bus (+ and -).
• Maximum number of radiofrequency devices that can be stored:
16 double rocker switches (each rocker switch can be saved to at most 4 different groups, group depth = 4)
no limit on the number of 01796.1 RF actuators, provided they belong to at most 30 groups.
3
Bus interface with EnOcean module
List of radio frequency devices that can be used
VIMAR Code DESCRIPTION / COMPOSITION
Flat control with two rocker buttons with EnOcean radio transmitter without batteries, power
20505
20506 - 19506 - 14506 Pair of buttons for control with EnOcean module 20505
01796.1 EnOcean multi-function 1-relay actuator, power supply 230 V~ 50-60 Hz.
N.B.: The flat control with two rocker push buttons 20505 is the radio unit on which pair of button must be mounted; this combi-
nation permits obtaining radio-frequency “lighting points”.
Operation
The device receives the signals emitted by the radiofrequency rocker push buttons and transmits the commands to the radio actuators.
• Normal operation from radio-frequency to Bus: it receives information from the radio rocker push buttons (pressing and releasing
the button) and controls the actuators over the Bus.
• Normal operation from Bus to radio-frequency: it receives the group messages from the devices over the Bus (single push-buttons,
rocker switches, etc.) and controls the actuators by radio-frequency.
• Radio interface configuration: in the phase of configuration the control panel passes minimal information to the interface: enabling
LED, index of the interface.
• Replacing radio interface: in this phase the By-me control panel transfers the radio devices present in the interface being replaced
to the new interface.
• Configuring radio-frequency devices: in the phase of adding radio devices, the interface with the EnOcean module saves the characteristics of the radio rocker button that responded and sends them to the control panel. In addition, the interface saves all the
information related to the configured radio actuators.
supply from the built-in electro-dynamic generator, to be completed with the dedicated buttons 20506-19506-14506
Indicators
• red LED on steady:
- during the configuration phase;
• green LED blinking (only if the LED enabling parameter is not Off):
- the interface is receiving or transmitting a radio-frequency message.
Settings (programmable via the control panel)
• Enabling LED:
- Normal: the green LED is normally off and blinks when receiving or transmitting a radio-frequency message.
- Inverted: the green LED is normally on and blinks when receiving or transmitting a radio-frequency message.
- Off: the green LED never lights up.
Standard compliance
R&TTE directive
Standards EN 50428, EN 301 489-3, EN 300 220-2.
4
Pair of buttons for flat control with EnOcean module
Pair of buttons for flat control with EnOcean module
The pair of buttons, suitably hooked onto the flat control with two rocker push buttons, permits obtaining the lighting point by radio
through which it is possible to carry out all the functions of automation (lights, roller shades, scenes, etc.) in a similar manner to the
conventional By-me control appliances.
IMPORTANT: The buttons can be specially customized with any symbol.
The pair of buttons can be supplied in the following versions:
20506: 2 Eikon modules
19506: 2 Arkè modules
14506: 2 Plana modules
Eikon
The flat control with the EnOcean module with two rocker push buttons, art. 20505, is supplied in the 2-module version.
Arké
Plana
20505
Technical characteristics
• Rated supply voltage (Vn): no kind of power supply is needed.
• Operating temperature: -5 - +45 °C (for indoor use)
• Transmission frequency: 868 MHz
• Installation: flush or surface mounting. Surface mounting installation, thanks to the special mounting frame (art. 21507, 20507, 19507,
20607, 14607), can be on materials such as, for instance, wood, masonry, etc.
• Capacity: 70 m in an open field; this value is less when there are walls and/or metal partitions. Before installing the device, always
take care to check the strength of the radio signal.
IMPORTANT: When the button is pressed, for the radio control to be transmitted, you must hear a mechanical “click”.
5
Loading...