Viking Electronics PA-IP Quick Start Manual

PA-IP

SIP Multicast Paging
Adapter with Amplifier

August 28, 2018

1.0 Out-of-Box

1.1 Verify that you have received all of the parts listed

PA-IP Paging Adapter
Qty: 1

8-position terminal block
Qty: 1

QUICK START GUIDE

VIKING

Electronics, Inc.

K See Product Manual for complete installation and programming instructions.

1.3 Download and install the programming software

1. Go to www.vikingelectronics.com and enter PA-IP in the search box

2. Click PA-IP in the search results

3. Scroll down the page to Downloads, click IP Programming Software

4. Install the programming software by saving or opening the file and then clicking on

setup Viking IP Programming.exe

5. Follow the prompts on your screen to complete software installation

2.0 Power Source

• Make sure the port is not in trunk mode

• Make sure port is capable of 100mbps full duplex

• Disable Spanning Tree Protocol (STP) or enable Portfast

Select PoE Switch or PoE Injector that meets the following requirements:

1. IEEE 802.3af / 802.3at / 802.3bu compliant

2. Capable of providing at least 13 Watts (class 0 or class 3)

Note: CAT5e (or higher) cable recommended

3.0 Network Port Settings

1.2 Download the product manual

1. Go to www.vikingelectronics.com and
enter PA-IP in the search box

2. Click PA-IP in the search results

3. Click Product Manual to open and
download the PDF

- OR -

Scan the QR code to

open and download

the product manual

4.0 Features Overview

Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.

See the Product Manual for complete installation and programming instructions.

Questions? Call Viking Product Support: 715-386-8666

PA-IP Quick Start Guide ZF303995 REV A

Green Unit Status LED

Red Page / Status LED

PoE LAN Port 10/100, PoE Class 3 (<13 Watts):

Connect to your LAN via RJ45 plug and CAT5 or
greater twisted pair wire.

Yellow Network Status LED: Lights steady to indicate
power and data link. Blinks to indicate network activity.

Relay Output Contact (2A@30VDC / 250VAC max):

Connect to trigger input of amplifier, etc.

Switch or Contact Input: To manually trigger Night Ring

30AE

25AE

40AE

Speaker Out

40AE

35AE

300AE

Up tp (6) Optional Viking Analog Speakers,

see DOD 497 and 498 (not Included)

Optional Paging Amplifier

Viking model PA-60 shown (DOD 493)

VIKING©

Line Out
600 Ohm
Paging
Audio

Up to (15)

8 Ohm Speakers

(25AE shown,

not included)

Up to (15)

8 Ohm Speakers

(30AE shown,

_

not included)

PWR 60 W

+/ 24 VDC

PWR
LED

VIKING

ELECTRONICS

HUDSON,

60 WATT 2 ZONE

POWER AMPLIFIER

70V OUT

GAIN GAIN

SPKRS

SPKRS

LINE LEVEL AUDIO INPUT

2315 7101112

46

+

Bottom View

MODEL PA-60

WI

54016

CHANNEL 2 CHANNEL 1

70V OUT

SPKRS

SPKRS

LINE LEVEL

AUDIO INPUT

8

9

Up to (15)

8 Ohm Speakers

(35AE shown,

not included)

Up to (15)

8 Ohm Speakers

(40AE shown,

not included)

Model:

xxxxxx

S/N: XXXXXXXX

xxxxxxxx

P/N: DEV:

Viking Electronics, Inc. [phone]
1531 Industrial St., Hudson, WI 54016

VIKING

www.vikingelectronics.com DOD#

MAC Address Label:

The MAC address is a unique 12 digit

number used by network equipment to send

MAC: 18E80FXXXXXX

asdesaxtff

data packets to the correct IP address.