Page 1
PPrraaccttiicce
e
T
T
EELLEECCOOM
M
S
S
OOLLUUTTIIOONNSSFFOORRTTHHE
E
221
1
SST
T
C
C
EENNTTUURRY
Y
TECHNICAL
TECHNICAL
Provide Reliable and Intelligent
Handsfree Communication!
The E-30 handsfree phone is designed to provide quick and reliable
handsfree communication and can be connected directly to a C.O.
line or analog PABX/KSU station.
The E-30 features non-volatile memory, a built in dialer, and intelligent call progress detection for automatic hang-up when the call is
completed.
The E-30 can be programmed to dial
up to 5 different numbers on ring no
answer or busy and can be configured
to dial these numbers until answered.
FFeeaattuurrees
s
Power: Telephone line powered. Minimum 24V DC talk battery voltage,
with a minimum loop current of 20mA loop. Loop current may be boosted
on low current lines with a Viking Model TBB-1B talk battery booster (Fax
Back # 632).
Minimum Ring Voltage: 25VAC RMS
REN #: 0.5A
Dimensions: Overall-127mm x 127mm x 57mm (5” x 5” x 2.25”),
Plastic Electrical Box-102mm x 102mm x 54mm (4” x 4” x 2.12”)
Shipping Weight: 1 Kg (2.2 lbs)
Operating Temperature: -26°C to 54°C (-15°F to 130°F)
Humidity - E-30: 5% to 95% non-condensing
Humidity - E-30-EWP: Up to 100% condensing
Connections: Gel-filled butt connectors
SSppeecciiffiiccaattiioonns
s
The E-30-EWP shares all of the features of the E-30 in addition
to Enhanced Weather Protection (EWP) for installation in harsh
environments. EWP products feature rubber gaskets and boots,
silicon sealed connections, gel-filled butt connectors, as well as
urethane potted circuit boards with weather sealed, fieldadjustable trim pots and DIP switches for easy on-site programming.
E-30/E-30-EWP
E-30/E-30-EWP
Handsfree Speaker
Phone with Dialer
June 22, 2010
• Handsfree operation
• Phone line powered
• Vandal resistant, stainless steel faceplate with
heavy-duty metal call button
• Non-volatile E
2
memory (no batteries required)
• Touch Tone or pulse dialing
• Programmable to dial up to 5 numbers on busy
or ring no answer
• Red off-hook LED indicator
• Hangs up on CPC, silence, busy signal, return
to dial tone, time out or a Touch Tone command
• Programmable to auto-answer on incoming calls
• Remotely programmable
• Extended temperature range (-15°F to 130°F)
• E-30-EWP has Enhanced
Weather protection
• Flush mountable using included plastic rough-in box
• Optional VE-5x5 surface
mount back box
• E-30-EWP conforms to NEMA requirements
AApppplliiccaattiioonns
s
Non-ADA Hot-Line Phones for:
• Elevators • Stadiums
• Parking lots/ramps • Convention centers
• ATM machines
Gate and Door Entry Phones for:
• Business lobbies • Residences
• Pedestrian gates
E-30/E-30-EWP
E-30 shown with
optional VE-5x5
?
Need More Information on EWP?
Call (715) 386-4345 and select 859.
?
Need More Information on VE-5x5?
Call (715) 386-4345 and select 424.
CAUTION - 1 When installing on an analog extension of a phone system:
Some phone systems do not conform to analog telecom standards and might
not be compatible with the E-30 speaker phones. For a detailed description of
the telephone line specifications required for any of the E-30 phones, retrieve
Fax Back Document 869.
2
In louder background noise environments, the
push to talk version may be required (E-30-PT or E-30-PT-EWP).
PPhhoonnee......771155..338866..8888661
1
Page 2
IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT (715) 386-8666
Our Technical Support Department is available for assistance Monday 8am - 4pm and Tuesday through Friday 8am - 5pm central time. So that we can give you better service, before you call please:
1. Know the model number, the serial number and what software version you have (see serial label).
2. Have your Technical Practice in front of you.
3. It is best if you are on site.
RETURNING PRODUCT FOR EXCHANGE
The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):
1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The
customer MUST be able to step through recommended tests for diagnosis.
2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input
and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14)
calendar days from the date of issue.
3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your
distributor will then replace the product over the counter at no charge. The distributor will then return the product to
Viking using the same R.A. number.
4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't
followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.
RETURNING PRODUCT FOR REPAIR
The following procedure is for equipment that needs repair:
1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)
number. The customer MUST have a complete description of the problem, with all pertinent information regarding the
defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.
2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static
sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individually boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include
ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to:
Viking Electronics, 1531 Industrial Street, Hudson, WI 54016
3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.
4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.
the necessary modifications to maintain uninterrupted service.
If trouble is experienced with the E-30, for repair or warranty information, please contact:
Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI 54016 (715) 386-8666
If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.
Connection to Party Line Service is subject to State Tariffs. Contact the state public utility commission, public service com-
mission or corporation commission for information.
WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST CALLS TO EMERGENCY NUMBERS:
Remain on the line and briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak
hours, such as early morning or late evenings.
It is recommended that the customer install an AC surge arrester in the AC outlet to which this device is connected. This
is to avoid damaging the equipment caused by local lightning strikes and other electrical surges.
PART 15 LIMITATIONS
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.
FCC REQUIREMENTS
This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. Inside the front panel
of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone company.
The REN is used to determine the number of devices that may be connected to a telephone line. Excessive REN's on a
telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of
the REN's should not exceed five (5.0) To be certain of the number of devices that may be connected to a line, as determined by the total REN's, contact the local telephone company. For products approved after July 23, 2001, the REN for
this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.
The plug used to connect this equipment to the premises wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. If your home has specially wired alarm equipment connected
to the telephone line, ensure the installation of this E-30 does not disable your alarm equipment. If you have questions
about what will disable alarm equipment, consult your telephone company or a qualified installer.
If the E-30 causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the customer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the
operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make
LIMITED WARRANTY
Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manufactured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's
Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.
This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others.
NO OTHER WARRANTIES
. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FIT-
NESS FOR ANY PARTICULAR PURPOSE.
EXCLUSION OF CONSEQUENTIAL DAMAGES
. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAM-
AGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.
EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY
. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL
BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.
IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED
AS SUCH.
2
Page 3
FFeeaattuurreessOOvveerrvviieew
w
IInnssttaallllaattiioon
n
The optional VE-5x5 Surface Mount Box is designed
to be surface mounted to a single gang box, double
gang box or VE-GNP gooseneck pedestal (right).
Important: The E-30 will NOT mount
to a standard double gang box.
Caution: When warm air comes in contact with cold surfaces, such as outside walls and conduits, it causes condensation. To prevent
condensation from accumulating inside the E-30 always bring conduit into the bottom of the unit. If this is not possible, drill a 1/4” diameter hole in the bottom of the gray plastic box.
*Note: Peel off paper liner and adhere gasket to the back of the faceplate, centering it over the four corner mounting holes. Be careful
to position the modular jack inside the chassis as not to damage the components on the circuit board.
Note: The plastic rough-in box (part # 259576) may be purchased separately
in advance. Go to www.vikingelectronics.com and click on “Spare Parts”.
?
Need More Information on VE-5x5 or VE-GNP?
Call (715) 386-4345 and select 424.
IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the
telephone line. It is recommended that a surge protector be installed to protect against such surges. Contact Panamax at (800)
472-5555 or Electronic Specialists Inc. at (800) 225-4876.
!
A. Mounting
3
Mounting Screws: 6-32 x 0.75" long
flathead with 5/64" hexdrive, 18-8 stainless
steel to prevent corrosion.
Faceplate: 14 guage 304 stainless steel.
Condensation Drain Hole
DIP Switches (see page 7):
1: Normal Audio Detection
2: Increased Audio Detection
Microphone Volume
Speaker Volume
VIKING
Microphone: Omni-directional microphone
with protective water-resistant cloth.
Speaker: Mylar speaker with rubber gasket to
maintain water-tight seal and eliminate water
deterioration.
Speaker Screen: Stainless steel speaker
screen with 0.018" diameter holes to prevent
Call
©
ON
1
2
punctures from paperclips, etc.
Push Button Switch: Push to initiate call,
push again to disconnect. Solid 304 stainless
steel internally sealed per IP67.
LED: Lights red for "In-Use" indication.
Faceplate Gasket: 1/8" thick closed cell PVC
to provide a water-tight seal.
Earth Ground: To increase surge protection,
loosen the screw labeled (as shown) and
DIP Switches (see page 7):
1: Push Button Feature (connect / disconnect)
2: Auto Answer Feature (on/off)
3: Programming Switch (normal/programming)
fasten a wire with ring terminal (included) from
the mounting screw to Earth Ground (grounding
rod, water pipe, etc.)
(4) 0.38” diameter
(for gooseneck mounting)
(4) 0.2 x 0.43 slots
for double gang box
(2) 0.2 x 0.43 slots
for single gang box
(1) .74" dia
Drain Hole
3.0”
Rear View of VE-5x5
(not included)
3.0” 3.3”
E-30-EWP shown
with Viking Model
VE-GNP
Gooseneck
Pedestal
Front View of
Plastic Rough-In
Box (included)
Wall Stud
Wire knock out
(2) Standard flat head dry wall
(sheet rock) screws (not included)
4.0"
2.1”
* Adhere gasket to front panel,
centering over mounting holes
5.0”
Call
Push to Call Button
Red Off-Hook LED Indicator
Condensation Drain Hole
(4) 6-32 X 3/4” stainless steel, flat
head, hexdrive, screws (included)
5.14”
2.25”
5.22”
3.25”
Condensation
Front View of Optional
VE-5x5 (not included)
Page 4
1 2 3
on
4 5
*** Note: To increase surge protection, loosen the PCB mounting screw labeled (as shown above) and fasten a wire with spade terminal (included)
from the mounting screw to Earth Ground (grounding rod, water pipe, etc.)
** Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a maximum insulation of 0.082
inches. Cut off bare wire ends prior to terminating.
* Note: When installing a line powered phone on a low voltage and/or low loop current phone system extension, a TBB-1B Talk Battery Booster may be
required, see DOD# 632.
B. Wiring the E-30 Phone Board
4
PPrrooggrraammmmiinng
g
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section F).
Step 2. From a Touch Tone phone call the line attached to the E-30.
Step 3. When the E-30 answers, enter the 6-digit security code (factory set to 845464 - see section C). A double beep
should then be heard indicating you have entered the programming mode.
2. Without the Security Code
A. Accessing the Programming Mode
1. Using the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls - see section F).
Step 2. Move DIP switch 3 to OFF (incoming calls enter the programming mode without security code - see section F).
Step 3. From a Touch Tone phone call the line attached to the E-30.
Step 4. When the E-30 answers, a double beep will be heard and you will automatically enter the programming mode.
Step 5. When finished programming, move DIP switch 3 back to the ON position (see section F).
Note: If a valid memory position is entered, a double beep will be heard, four beeps indicate an error.
?
Need More Information on the DLE-200B?
Call (715) 386-4345 and select 605.
The E-30 phone can be programmed from any Touch Tone phone using a C.O. line, analog PABX/KSU station, or a
DLE-200B Line Simulator.
B. Quick Programming Features
First speed dial number ...........................................................................................
Second speed dial number ......................................................................................
Third speed dial number ..........................................................................................
Fourth speed dial number ........................................................................................
Fifth speed dial number ...........................................................................................
To add a
, at any point in the dialing string ...............................................................
To add a # at any point in the dialing string ...............................................................
To add a four second pause at any point in the dialing string ....................................
Toggle between Touch Tone and Pulse dialing .........................................................
Miscellaneous options (factory set to 000210) .........................................................
Timing/Dialing options (factory set to 234111) .........................................................
Change security code (factory set to 845464) .........................................................
Exit programming and disconnect ...........................................................................
Reset all programming to factory default settings ....................................................
0-20 digits
0-20 digits
0-20 digits
0-20 digits
0-20 digits
,,
,
#
,7
,6
6 digits (0-9)
6 digits (0-9)
6 digits (0-9)
#7
###
#00
#01
#02
#03
#04
#17
#18
#19
Enter Digits
then
then
then
then
then
then
then
then
- then -
Enter Memory Location
5.0”
Optional C-2000B Advanced Door
Entry Controller (not included)
VIKING
©
MODEL C-2000B
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
PWR 13.8 VAC
EARTH GND
ENTRY PHONE 1
DOOR STRIKE 1
ENTRY PHONE 2
DOOR STRIKE 2
ENTRY PHONE 3
DOOR STRIKE 3
ENTRY PHONE 4
PHONE LINE
INPUT
LINE OUT
TO PHONES
ANALOG STATION
INPUT
1 2 3 4 5 6 78910 11 12 13 15 16 17 1819 20 21 22 2324 25 26 27 2829 30 31 32
on
J7-
1
3
2
LED1 LED2
LED3
LED4
C C
DOOR STRIKE 4
J10-
J9-
J8-
1
1
3
2
3
12
2
3
LED6
CCCC
LED5
Optional C-200 or C-250 Single Entry
Phone Controller (not included)
VIKING
C
SINGLE ENTRY PHONE
A
V
.8
CONTROLLER
3
1
R
W
P
RING COUNT
RELAY MODE
DOORBELL MODE
DOORBELL SWITCH /
AUX. INPUT
AUX. CONTACT
OUTPUT
J11-
3
2
1
LED7
C
ON
1 2 3
©
MODEL C-200
VIKING
ELECTRONICS
HUDSON, WI 54016
EARTH
GND
LINE OUT
TO PHONES
TO ENTRY
PHONE LINE
INPUT
12345 89
67
EARTH
C.O. LINE
OUT TO
ENTRY
GND
INPUT
PHONES
PHONE
or
PHONE
Y
A
L
E
R
X
U
A
N.O. COM N.C.
AUX CONTACTS
Rear View of
* C.O. Line
OUTPUT
or Analog
PABX/KSU
Station
Butt Connectors
S
T
C
A
T
N
O
C
AUX POWER
10
11 12
AUX POWER
OUTPUT
or
the E-30
** Gel-Filled
Red (Ring)
Green (Tip)
3.63”
ON
1
2
5.0”
3.63”
Ring
Terminal
(included)
*** Earth
Ground
(optional)
Page 5
5
E. Timing/Dialing Options (Memory Location #18)
There are six positions in the timing/dialing options. To program these options, enter the six desired timing/dialing digits followed by #18. The six available timing/dialing options are defined as shown below.
Dial: A +B+C+D+E+F+#+1+8
Factory Default Setting:2+3 +4+1+ 1+1
Talk/Listen Delay
Call Length
Silence Time Out
Dial Next Number on Ring No Answer
Dial Next Number on Busy
Pulse Dial Speed
Enter Timing/Dialing Settings Here:
A B C D E F
#18
Setting A - Talk/Listen Delay
This feature selects switching time between talk and listen modes
(VOX switching time). Use chart at the right. * Note: The factory
default is .2 seconds.
Setting B - Call Length Time Out
This feature selects the maximum length of time that calls can be connected. Programmable
in increments of 1 minute up to a maximum of 9 minutes (Touch Tones 1 - 9). Program 0 in
this location to disable the call length time out. With the call length disabled, the E-30 phone
must rely on CPC, busy, reorder, silence or return dialtone to hang-up. Use chart at the far
right. *Note: The factory default is 3 minutes.
Touch
Tone
1
2
3
4
5
6
7
8
9
Talk/Listen
Delay
.1 sec
.2 sec *
.3 sec
.4 sec
.5 sec
.6 sec
.7 sec
.8 sec
.9 sec
Touch
Tone
0
1
2
3
4
5
6
7
8
9
Call Length
Time Out
Disabled
1 min
2 min
3 min*
4 min
5 min
6 min
7 min
8 min
9 min
D. Speed Dial Numbers (Memory Locations #00 - #04)
Note: Up to 20 digits can be stored in each dial position. Special features such as pause, mode change, Touch Tone
,
and # count as single digits.
The speed dial number programmed in location #00 is the telephone or extension
number that is dialed when the “Call” button is first pressed. Additional speed dial
numbers will be dialed when there is no answer or a busy signal is detected and the
next number redial features are activated. The E-30 will cycle through the programmed speed dial numbers until answered. To program, enter the desired speed
dial number followed by the memory location number (#00 - #04).
To clear a speed dial location, simply enter the memory location (#00 - #04) alone.
The E-30 is factory set with no speed dial number programmed.
To Program:
,
#
4 second pause
switch to pulse mode
0, 1, 2...9
Enter:
,,
,#
,7
,6
0, 1, 2...9
C. Security Code (memory location #19)
The security code allows the user/installer to program the E-30 phone while DIP switch 3 is in the ON (normal) position. The factory set security code is 845464 (V-I-K-I-N-G). It is recommended that the factory set security code be
changed. Example: To store 123456 as the security code:
Enter Your Security Code Here:
#19
Step 1. Access programming as shown is Programming section A.
Step 2. Enter 123456 #19..
Step 3. Hang-up.
Note: The security code must be 6 digits and cannot include a ,or a #.
Page 6
6
Setting C - Silence Time Out
This feature selects the length of time that calls will remain connected without voice activity.
Programmable in increments of 10 seconds up to a maximum of 90 seconds (Touch Tones
1 - 9). To disable the silence time out, program 0 in this location. Use chart at the right.
* Note: The factory default is 40 seconds.
Setting D - Dial Next Number on Ring No Answer
If enabled and a ring-no-answer is detected, the E-30
phone will dial the next programmed speed dial number, and continue to cycle through the emergency
numbers until a call is completed. * Note: This feature is disabled in the factory default.
Touch
Tone
0
1
2
3
4
5
6
7
8
9
Silence
Time Out
Disabled
10 sec
20 sec
30 sec
40 sec*
50 sec
60 sec
70 sec
80 sec
90 sec
If enabled and a busy is detected, the E-30 phone will dial the next programmed
speed dial number, and continue to cycle through the emergency numbers until a
call is completed. * Notes: This feature is disabled in the factory default setting. If
the busy signal is interrupted with a promotional message, contact your central
office to have it removed.
Setting E - Dial Next Number on Busy
Setting F - Pulse Dialing Rate (Pulses per Second)
The E-30 phone is capable of different pulse dialing speeds. * Note: The factory
default setting is 10pps (pulses per second).
Touch Tone
1
2
Setting F
10 pps*
20 pps
Touch Tone
1 or 0
2, 3, 4...9
Setting D
Disabled*
Dials second number after
2, 3, 4...9 rings respectively
Touch Tone
1
2
Setting E
Disabled*
Enabled
Settings A /B/C-NotApplicable
F. Miscellaneous Options (memory location #17)
Dial: A +B+C+D+E+F+#+1+7
Factory Default Setting:0+0 +0+2+ 1+0
Not Applicable (enter 0)
Hang-up on Return to Dial Tone
Panasonic Mode
Lap Counter
Enter Settings Here:
A B C D E F
0 0 0 #17
If enabled and a return dial tone is detected, the E-30 will hang up.
* Note: The factory default setting is enabled.
Touch Tone
1
2
Setting D
Disabled
Enabled*
Setting D - Hang Up on Return to Dial Tone
The E-30 can be programmed to recognize the double ring cadence that is typical of
Panasonic phone systems. If the E-30 is connected to a Panasonic extension, (or any other
system that provides a double ring cadence) enable “Panasonic Mode” will allow for proper
call progress detection.
* Note: This feature is disabled in the factory default setting.
Touch Tone
1
2
Setting E
Disabled*
Enabled
Setting E - Panasonic Mode
Page 7
7
G. DIP Switch Programming/Speaker and Microphone Adjustments
Two POTs are provided to increase or decrease speaker volume and microphone sensitivity. In certain noisy locations
the microphone sensitivity may need to be decreased as shown below. Caution: Setting the microphone gain too high
may cause distorted audio, prevent the distant party from breaking over and inhibit second number redialing.
DIP
Switch
1
1
2
2
3
3
Position
ON
OFF
ON
OFF
ON
OFF
Description
“CALL” button alternately connects and disconnects
calls (factory default)
“CALL” button connects calls only
Incoming calls answered (factory setting)
Incoming calls are not answered
Normal operation mode (factory setting)
Learn mode - Any incoming calls are automatically entered
into the programming mode (no security code required).
Use this option if you have forgotten your security code.
Switch
A
ON
OFF
Description
Normal audio detection
Increase audio detect sensitivity for low level lines. Useful
in applications in which voice or busy signals have trouble
breaking over to the speaker.
Switch
B
ON
OFF
With the lap counter disabled (factory setting), if the E-30 is programmed to dial
the next number on ring-no-answer and/or busy signal (see page 5 and 6), the
E-30 will continuously call its programmed phone numbers forever until the call
is answered.
Touch Tone
0
1-9
Setting F
Disabled*
Lap count = 1-9 times
Setting F - Lap Counter
The lap counter is a programmable counter that determines how many times the E-30 will cycle through its list of up to 5 emergency number (or up to 3 “Info” phone numbers), before it stops the dialing process and hangs up. When all of the programmed
phone numbers have been dialed, the lap counter is incremented and the dialing process repeats. When the lap counter has
been met, the dialing process stops and the E-30 hangs up. * Note: This feature is disabled in the factory default setting.
To Program the E-30 Phone...
...to store 123456 as the security code
...to store a Touch Tone 9, a four second pause and then a pulse
dialed 333-4444 in the first speed dial position
...to store 555-1234 in the second speed dial position
Step 2 - Enter Digits:
1 2 3 4 5 6 # 1 9
9
,7 ,6 3 3 3 4 4 4 4 # 0 0
5 5 5 1 2 3 4 # 0 1
Step 1 -
See Section A
Enter Programming
Enter Programming
Enter Programming
H. Programming Examples
OOppeerraattiioon
n
When the “Call” button is pressed, the E-30 phone goes off-hook, and dials a pre-programmed telephone number. The front
panel LED will light any time the phone is off hook. In the event that the line is busy or there is a ring-no answer, the unit
can be programmed to call additional phone numbers. The phone then cycles through up to 5 pre-programmed speed dial
numbers until the call is answered. The E-30 will hang up on CPC, silence, busy signal, return to dial tone, time out or Touch
Tone command (
,#). If programmed to auto-answer, the E-30 will also answer any incoming call.
O
OFF
O
OFF
N
N
A B
1 2 3
M
icr
S
ensitivit
ophon
e
S
p
eake
V
olume
r
y
Page 8
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
DOD# 212
ZF302710 Rev B
Printed in the U.S.A.
PPrroodduuccttSSuuppppoorrttLLiinnee......771155..338866..8866666
6
FFaaxxBBaacckkLLiinnee......771155..338866..4433445
5
8
OOtthheerrPPrroodduucctts
s
The C-2000B now offers two operational modes for added flexibility.
In the Single Line Ring Through Mode, the C-2000B allows single line phones to
share a phone line with 1 to 4 entry phones. Tenants may converse with visitors
and activate a contact closure to control gates or strikes. The C-2000B provides
entry phone “Caller ID” and “Call Waiting Caller ID” and a “Call Waiting” tone when
the phone lines is in use. Tenants may gain entry at each location by entering a keyless entry code.
In the Analog Station Dial Through Mode, the C-2000B allows 1 to 4 entry phones
to share one analog PABX extension or telephone line and place outgoing calls.
When a remote party answers, they can converse with visitors and activate a contact closure to control gates or strikes. Monitoring entry phones, forcing doorstrike relays to operate or remote programming of the C-2000B can be accomplished by calling the analog PABX extension or telephone line connected. Authorized
personnel may gain entry at each location by entering a keyless entry code. For more information, see DOD# 156.
Add 1-4 Entry Phones and Doorstrike Control to an Existing Phone Line
AApppplliiccaattiioonns
s
C-2000B Advanced Door/Gate and Entry Phone Controller
The C-2000B allows up to 4 entry phones to call into your existing residential or business phones or phone system. Tenants
may answer the call, converse with the visitor and activate a contact closure to control electronic gates or door strikes. The
C-2000B provides “Caller ID,” “Call Waiting ID” and “Call Waiting” tone when the phone line is in use. Tenants may gain
entry at each gate by entering a Touch Tone keyless entry code. Tenants may call out to each entry phone for monitoring
purposes. An auxiliary input is also available for connecting a common garage door opener/receiver and auxiliary keyless
entry keypads. See the C-2000B Technical Practice for complete installation instructions, DOD# 156.
To Standard
Analog Touch
Tone House
Phone(s)
C.O. / Phone
Line Input
120V AC
13.8V AC
Adapter
(included)
Earth
Ground
(optional)
VIKING
PWR 13.8 VAC
EARTH GND
PHONE LINE
INPUT
LINE OUT
TO PHONES
1 2 3 4 5 6 78910 11 12 13 15 16 17 18 19 20 21 22 23 24 25 26 27 2829 30 31 32
on
123
4 5
LED1 LED2
C C
Entry Phone 2
(E-30 shown)
©
VIKING
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR/GATE AND
ENTRY PHONE CONTROLLER
ANALOG STATION
INPUT
ENTRY PHONE 1
DOOR STRIKE 1
ENTRY PHONE 2
DOOR STRIKE 2
14
J8-
J7-
1
1
2
LED3
Entry Phone 1
(E-40-PB shown,
not included)
2
3
3
LED4
MODEL C-2000B
ENTRY PHONE 3
DOOR STRIKE 3
J9-
1
3
2
LED5
Entry Phone 3
(E-60-BN shown,
not included)
ENTRY PHONE 4
DOOR STRIKE 4
DOORBELL SWITCH /
AUX. INPUT
AUX. CONTACT
OUTPUT
J10-
J11-
3
12
LED6
To Entry
Phone 4
3
2
1
LED7
C
CCCC
required for gate controllers)
A contact closure output is available for each
entry phone. An auxiliary output is also available.
Optional Doorbell Switch
(not included, see Programming
section M on page 9)
or
Entry Phone 4
(E-30 shown,
not included)
(Power typically not
Optional Postal Lock
(not included)
5A@30VDC/
250VAC
maximum
Doorstrike/
Magnetic Lock
Loading...