Viking VWH, DCH User Manual

Page 1
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
All models include
design with no visible screws
• Heat sensor turns the ventilator on full power when cooking temperatures reach uncomfortable levels
• Recommended for 24”W., 30”W. & 36”W. non-griddle/grill ranges, rangetops, and cooktops
• 460 CFM interior-power ventilator comes standard with product o Variable speed controls for custom
venting—separate on/off switch allows you to leave ventilator at favorite/most-used setting
• Two 50-watt halogen lights with dimmer control o Power switch and dimmer control
are separate, allowing you to leave dimmer at favorite position
• Easy cleanup o Design of low-profile filter system
means less interior hood space to be cleaned
o Canopy interior is completely lined
in stainless steel for increased rigidity, seamless appearance, and easy cleaning
Professional 10”H. hoods include
• Commercial-type size, design, and styling
• Allow replacement of most older hoods with minimal cabinet alteration
• Commercial-type baffle filter system efficiently removes grease and heated vapors from the air; especially designed for use with commercial­type products
Designer 12”H. hoods include
• Professional-type size, design, and styling
• Delay function—can be set to shut off from 10 – 30 minutes later (10 min. increments)
• 12-hour timer built into controls
• Two dishwasher-safe stainless steel mesh filters are easily removed for quick cleaning (frame and mesh are stainless steel)
Model numbers
PROFESSIONAL WALL HOODS, 10”H./21”D.
• VWH2410—24”W. o Recommended for use with 24”W. non-griddle/grill ranges (for larger equipment, use 18”H. hood)
• VWH3010—30”W. o Recommended for use with 30”W.
ranges, 30”W. non-griddle/grill rangetops, and 30”W. cooktops
• VWH3610—36”W. o Recommended for use with 36”W.
non-griddle/grill ranges, 36”W. non­griddle/grill rangetops, and 36”W. cooktops
DESIGNER CHIMNEY WALL HOODS, 12”H./24”D.
• DCH3042—30”W. o Recommended for use with 30”W.
ranges, 30”W. non-griddle/grill rangetops, and 30”W. cooktops
• DCH3642—36”W. o Recommended for use with 36”W.
ranges, 36”W. non-griddle/grill rangetops, and 36”W. cooktops
Racing Red (RR), Apple Red (AR), Burgundy (BU), Plum (PL), Chocolate (CH), and Cobalt Blue (CB).
• Finish designates front and sides.
• Accessory Rail Option—Front of hood.
(Must be ordered factory installed) o Stainless Steel/Chrome (CR)—
Stainless steel rail with chrome supports/brackets and hooks (included).
o Brass Trim Option (BR)—rail,
supports/brackets, and hooks (included). Brass components have a durable protective coating for maintenance-free normal use.
supports/brackets and hooks (included).
o Brass Trim Option (BR)—nameplate,
rail, supports/brackets, and hooks (included). Brass components have a durable protective coating for maintenance-free normal use.
FINISH DETAILS DESIGNER MODELS
• Stainless Steel (SS), Black (BK), White (WH), Metallic Silver (MS), Graphite Gray (GG), Stone Gray (SG), Taupe (TP), Biscuit (BT), Cotton White (CW), Oyster Gray (OG), Golden Mist (GM), Lemonade (LE), Sage (SA), Mint Julep (MJ), Sea Glass (SE), Iridescent Blue (IB), Viking Blue (VB), Pumpkin (PM),
FINISH DETAILS FOR PROFESSIONAL MODELS
• Stainless Steel (SS), Black (BK), White (WH), Metallic Silver (MS), Graphite Gray (GG), Stone Gray (SG), Taupe (TP), Biscuit (BT), Cotton White (CW), Oyster Gray (OG), Golden Mist (GM), Lemonade (LE), Sage (SA), Mint Julep (MJ), Sea Glass (SE), Iridescent Blue (IB), Viking Blue (VB), Pumpkin (PM), Racing Red (RR), Apple Red (AR), Burgundy (BU), Plum (PL), Chocolate (CH), and Cobalt Blue (CB).
• Finish designates front and sides.
• Accessory Rail Option—Front of hood. (Must be ordered factory installed) o Stainless Steel/Chrome (CR)—
Stainless steel rail with chrome
VWH Professional
Wall Hood
DCH Designer Chimney
Wall Hood
Standard Features & Accessories
Model Options
ORDERING INSTRUCTIONS
First specify model number, followed by color code (VWH2410SS). If ordering optional decorative rail, specify code at end (VWH2410SSCR).
Page 2
24”
(61.0 cm)
16”
(40.6 cm)
12”
(30.5 cm)
2”
(5.1 cm)
12”
(30.5 cm)
A
2 ”
(5.1 cm)
21”
(53.
3 cm)
A
12”
(30.5 cm)
10 ”
(25.4 cm)
4 ”
(10.2 cm)
6”
(15.2 cm)
VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
24”
(61.0 cm)
16”
(40.6 cm)
12”
(30.5 cm)
18”
(45.7 cm)
to
30”
(76.2 cm)
12”
(30.5 cm)
A
2 ”
(5.1 cm)
Please see
Installation Notes &
Accessories for
important information,
including conversion
kits, filters, duct
covers, backsplashes,
and warming shelf
panels.
21”
(53.3 cm)
A
12”
(30.5 cm)
10 ”
(25.4 cm)
12 ”
(30.5 cm)
6”
(15.2 cm)
Dimensions & Specifications
PRODUCT DIMENSIONS
VWH Professional
Wall Hood
DCH Designer Chimney
Wall Hood
PROFESSIONAL DESIGNER
Model Hood Duct Cover Lights Filters Heat Approx.
Width (A) Height Width Depth Height Lamps Ship. wt.
VWH2410 23-7/8” (60.6 cm) 10” (25.4 cm) 23-7/8” 12” (30.5 cm) 12” (30.5 cm) 2 2 N/A 48 lbs.
(60.6 cm) (21.7 kg)
VWH3010 29-7/8” (75.9 cm) 10” (25.4 cm) 29-7/8” 12” (30.5 cm) 12” (30.5 cm) 2 2 N/A 56 lbs.
(75.9 cm) (25.2 kg)
VWH3610 35-7/8” (91.1 cm) 10” (25.4 cm) 35-7/8” 12” (30.5 cm) 12” (30.5 cm) 2 2 N/A 60 lbs.
(91.1 cm) (27.0 kg)
DCH3042 29-7/8” (75.9 cm) 12” (30.5 cm) 16” (40.6 cm) 12” (30.5 cm) 18” (45.7 cm)— 2 2 N/A 56 lbs.
30” (76.2 cm) (25.2 kg)
DCH3642 35-7/8” (91.1 cm) 12” (30.5 cm) 16” (40.6 cm) 12” (30.5 cm) 18” (45.7 cm)— 2 2 N/A 60 lbs.
30” (76.2 cm) (27.0 kg)
PROFESSIONAL W/RECIRCULATING KIT
DESIGNER W/RECIRCULATING KIT
Page 3
30”min.
(76.2 cm)
to
33”max.
(83.8 cm)
66”min.
(167.6 cm)
to
69”max.
(175.3 cm)
36”
(91.4 cm)
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
24”min.
(61.0 cm)
to
27”max.*
(68.6 cm)
60”min.
(152.4 cm)
to
63”max.
(160.0 cm)
36”
(91.4 cm)
Dimensions & Specifications
CLEARANCE DIMENSIONS
PROFESSIONAL
DESIGNER
*Note: When installing with a 24” high-shelf, the 27” (68.6 cm) max. dimensions must be used.
Page 4
Proper installation/ ducting is extremely important to ensure maximum performance. Use a qualified and trained installer.
DUCTING
• 460 CFM interior (blower included)
• Check with a qualified and trained installer for local codes and makeup air requirements, if any.
• Max. duct run length—50’ (152.4 m)
o Duct run length is for
general reference only; for longer duct runs, increase duct size and contact a qualified and trained installer.
o Straight runs and gradual turns are best; for example, each 90° elbow is equivalent to 5’ – 10’ (1.52 – 3.05 cm) of straight run.
• 7” round duct o Never use flexible duct; it
creates back pressure/air turbulence and greatly reduces performance.
GAS
Not applicable
ELECTRICAL
• Hardwire direct with two-wire with ground
• 120 VAC/60 Hz
• Max. amp usage—5.6
PLUMBING
Not applicable
VWH Professional
Wall Hood
DCH Designer Chimney
Wall Hood
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
UTILITY REQUIREMENTS
Installation Requirements
Model Interior Ventilator Kits Interior Duct Size Interior Max. Amps
VWH2410 460 CFM standard 7” (17.8 cm) 5.6 VWH3010 460 CFM standard 7” (17.8 cm) 5.6 VWH3610 460 CFM standard 7” (17.8 cm) 5.6 DCH3042 460 CFM standard 7” (17.8 cm) 5.6 DCH3642 460 CFM standard 7” (17.8 cm) 5.6
Note: All CFMs are based on tests with 0.1 static pressure. Without applying static pressure (some brands do not), CFM could be greatly overstated.
Page 5
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
Recirculating Hood Conversion Kits
• Stainless Steel (SS)
• Eliminates ducting
• Kit includes o Two charcoal filters o Installation hardware o Top vent/grille
Professional—4”H. x 12”D.
Designer—2”H. x 12”D.
Charcoal Filters
• For use with VRK & DRK conversion kits
• Recommended replacement every 6 – 12 months
Duct Covers
• Specify finish code following accessory model number (for example, DCW24-SS) o Professional models
For VWH hoods
12”D.
Extends height of hood by 12”—conceals duct
Available in Stainless Steel (SS), Black (BK), White (WH), Almond (AL), Biscuit (BT), Stone Gray (SG), Graphite Gray
(GG), Burgundy (BU), Lemonade (LE), Mint Julep (MJ), Forest Green (FG), Viking Blue (VB), Cobalt Blue (CB), and Eggplant (EP).
o Designer models
For DCH hoods
For 8’ – 9’ ceilings
Available in Stainless Steel (SS), Black (BK), White (WH), Biscuit (BT), Stone Gray (SG), Graphite Gray (GG).
Not needed if using a DCLF1610
Installation Notes & Accessories
Model Description Approx. ship wt. lbs. (kg)
VRK24 Professional 24”W. conversion kit 10 (4.5) VRK30 Professional 30”W. conversion kit 13 (5.9) VRK36 Professional 36”W. conversion kit 16 (7.3) DRK30 Designer 30”W. conversion kit 15.4 (7) DRK36 Designer 36”W. conversion kit 15.4 (7)
Model Description Approx. ship wt. lbs. (kg)
CFV11 Professional hood filter for 24”W. 1 (0.5) CFV13 Professional hood filter for 30”W. & 36”W. 2 (0.9) CF-D12 Designer hood filter for 30”W. 2 (0.9) CF-D14 Designer hood filter for 36”W. 2 (0.9)
Model Description Approx. ship wt. lbs. (kg)
DCW24 Professional 24”W. duct cover 9 (4.0) DCW30 Professional 30”W. duct cover 10 (4.5) DCW36 Professional 36”W. duct cover 11 (5.0) DCC16 Designer adjustable duct cover – for DCH 30” & 36” models 20 (9.0)
Page 6
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
VENTILATION
Built-In 10”H. Wall Hood w/Ventilator/
12”H. Chimney Wall Hood w/Ventilator
Duct Cover Extension
• For DCH hoods
• 16”W. x 12”D. x 28 – 40”H.
• Extends height of hood by up to 12” (for 10’ ceilings)
• Replaces adjustable duct cover supplied standard with hood
• Specify finish code following accessory model number (for example, DCCE1610-SS)
• Available in Stainless Steel (SS), Black (BK), White (WH), Biscuit (BT), Stone Gray (SG), Graphite Gray (GG).
Backsplashes
• Stainless Steel (SS)
• 30”H.
• For both VWH & DCH hoods
• Backsplashes protect the wall space below hood
• Create a continuous finish between cooking surface and hood
• Low maintenance, easy to clean
• Hemmed edges with screw holes
• Kit includes backsplash and fastening screws
Warming Shelf Panels
• Stainless Steel (SS)
• 12”D. X 12”H.
• For both VWH & DCH hoods
• Shelf panels hold cookware and condiments
• Kit includes shelf (or shelves) and fastening screws
• Fold up/down, heavy-duty warming shelves (non-removable), factory installed on stainless steel backsplash
• 5-7/8”W. X 10-1/8”D.
Compliance Information
WARRANTY SUMMARY*
• One-year full warranty—complete product
• Five-year limited warranty—all ventilator motors
• Ninety-day limited warranty—cosmetic parts such as glass, painted, and decorative items
* For complete warranty see
Use & Care Guide
. Warranty valid on Viking products shipped within the United States and Canada.
Installation Notes & Accessories
Model Description Approx. ship wt. lbs. (kg)
DCCE1610 Designer duct cover extension 7 (15.4)
Model Description Approx. ship wt. lbs. (kg)
BKS24 24”W. backsplash 5 (2.3) BKS30 30”W. backsplash 7 (3.2) BKS36 36”W. backsplash 9 (4.1)
Model Description Approx. ship wt. lbs. (kg)
WGP24 24”W. warming shelf panel (one shelf) 6 (2.7) WGP30 30”W. warming shelf panel (one shelf) 9 (4.1) WGP36 36”W. warming shelf panel (two shelves) 12 (5.4)
Loading...