Viking VUAR153, DUAR153, DFUR154, DUAR154, VUAR154 User Manual

USE/INSTALLATION
INSTRUCTIONS

15” W. UNDERCOUNTER/FREESTANDING
REFRIGERATED BEVERAGE CENTER

Retain for Future Reference

IMPORTANT - PLEASE READ AND FOLLOW

••

Before beginning, please read these instructions completely and carefully.

• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.

• Please observe all local and national codes and ordinances.

• Please ensure that this product is properly grounded.

• The installer should leave these instructions with the consumer who should retain for local inspector’s use and for
future reference.

WARNING

TToo rreedduuccee tthhee rriisskk ooff ffiirree,, eelleeccttrriiccaall sshhoocckk,, oorr iinnjjuurryy wwhheenn uussiinngg yyoouurr rreeffrriiggeerraatteedd bbeevveerraaggee cceenntteerr,, ffoollllooww bbaassiicc
pprreeccaauuttiioonnss iinncclluuddiinngg tthhee ffoolllloowwiinngg::

::

•FOR YOUR SAFETY•

DO NOT STORE OR USE GASOLINE OR OTHER FLAMMABLE VAPORS AND LIQUIDS IN THE VICINITY OF THIS OR
ANY OTHER APPLIANCE. THE FUMES CAN CREATE A FIRE HAZARD OR EXPLOSION.

IItt iiss yyoouurr rreessppoonnssiibbiilliittyy ttoo bbee ssuurree yyoouurr rreeffrriiggeerraatteedd bbeevveerraaggee cceenntteerr iiss::

•located so the front is not blocked to restrict incoming or discharge air flow.

•properly leveled.

•located in a well ventilated area.

•connected to the proper kind of outlet, with the correct electric supply and grounding. A 115 volt, 60 Hz, 15 amp

fused electrical supply is required.

•not used by anyone unable to operate it properly.

•used only for its intended purpose.

•properly maintained.

NNOOTTEE::

Time delay fuse or circuit breaker is recommended.

•SAVE THESE INSTRUCTIONS•

PROPER DISPOSAL OF YOUR OLD REFRIGERATION PRODUCT

DANGER

SSuuffffooccaattiioonn HHaazzaarrdd
RReemmoovvee ddoooorrss ffrroomm yyoouurr oolldd
rreeffrriiggeerraatteedd bbeevveerraaggee cceenntteerr..
FFaaiilluurree ttoo ddoo ssoo ccaann rreessuulltt iinn
cchhiilldd eennttrraappmmeenntt wwhhiicchh ccaann
ccaauussee ddeeaatthh oorr bbrraaiinn ddaammaaggee

IIMMPPOORRTTAANNTT::
are not problems of the past. Junked or
abandoned refrigerated beverage centers are still
dangerous, even if they will sit for “just a few
days.” If you are getting rid of your refrigerated
beverage center, please follow the instructions
below to help prevent accidents.

BBEEFFOORREE YYOOUU TTHHRROOWW AAWWAAYY YYOOUURR OOLLDD
RREEFFRRIIGGEERRAATTEEDD BBEEVVEERRAAGGEE CCEENNTTEERR::

•Take off the doors.

•Leave the shelves in place so that children may
not easily climb inside.

Child entrapment and suffocation

41009335 Rev. B

UNDERCOUNTER CABINET CUTOUT

AA

15” (38.1 cm)*

BB

Min. 34 1/2” (87.6 cm)

Max. 35 1/8” (89.2 cm)

CC

Min. 24” (61.0 cm)

*15” (38.1 cm) width for cabinet only. If
door is recessed between cabinets,
cabinet cutout must be 15 1/4” (38.7 cm).

A

B

C

2

SPECIFICATIONS/DIMENSIONS
PROFESSIONAL SERIES

BBaassiicc EElleeccttrriicc DDaattaa

•115 VAC/60 Hz

•Maximum amps - 3.0

•Approximate Shipping Weight - 110 lbs. (49.5 kg)

Front View

Side View

30 3/4”
(78.1 cm)

37 3/16” (94.5 cm)

Min. 34 1/4”

(87.0 cm)

to
Max. 35”
(88.9 cm)

(with leveling

legs fully

extended)

14 3/4” (37.5 cm)

21 3/16” (53.8 cm)

23 5/8” (60.0 cm)
26 1/8” (66.4 cm)

3

SPECIFICATIONS/DIMENSIONS
DESIGNER SERIES

BBaassiicc EElleeccttrriicc DDaattaa

•115 VAC/60 Hz

•Maximum amps - 3.0

•Approximate shipping weight - 110 lbs (49.5 kg)

30 3/4”

(78.1 cm)

Front View

Mín.

34 1/4”

(87.0 cm)

to

Max.

35”

(88.9 cm)

(with

leveling

legs fully

extended)

Side View
DUAR

37 3/16” (94.5 cm)

23 5/8” (60.0 cm)

24 5/8” ( 62.5 cm)

14 3/4” (37.5 cm)

Side View
DFUR

37 3/16” (94.5 cm)

21 3/16” (53.8 cm)

21 3/16” (53.8 cm)

23 7/16” (59.5 cm)

(to front of locally supplied

custom panel

4

GENERAL INFORMATION

UUnnppaacckk

1. Remove banding from bottom of carton. Lift carton up and off of the refrigerated beverage center

2. Remove all tape and packaging material from the outside and inside of the cabinet.

3. Keep all carton packaging until your refrigerated beverage center has been thoroughly inspected and found to be in
good condition.

AARREEAA RREEQQUUIIRREEMMEENNTTSS
UUnniittss CCeerrttiiffiieedd ffoorr IInnddoooorr UUssee -- ((bbllaacckk oouutteerr ccaabbiinneett))

1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in
on the top and three sides, but the front
Installation should be such that the cabinet can be moved for servicing if necessary.

2. Unit should be in a well ventilated area with temperature above 550F (130C) and below 1100F (430C). Best results
are obtained at temperatures between 650F (180C) and 800F (270C) for built-in models and between 650F (180C) and
900F (320C) for freestanding models.

3. Provisions for electricity should be determined before placing unit in proper place.

UUnniittss CCeerrttiiffiieedd ffoorr OOuuttddoooorr UUssee -- ((ssttaaiinnlleessss sstteeeell oouutteerr ccaabbiinneett))
MUST BE INSTALLED IN AN AREA PROTECTED FROM THE ELEMENTS, SUCH AS WIND, RAIN, WATER (SPRAY OR DRIP).

1. Place unit so the front side will be completely unobstructed to provide proper air flow. The unit may be closed in
on the top and three sides, but the front
Installation should be such that the cabinet can be moved for servicing if necessary.

2. Unit should be in a well ventilated area with temperature above 400F (40C) and below 1100F (430C).

3. Provisions for electricity should be determined before placing unit in proper place.

MMUUSSTT BBEE

MMUUSSTT BBEE

unobstructed for air circulation and proper operation.

unobstructed for air circulation and proper operation.

REVERSIBLE DOOR (Glass Door Units Only)
PROFESSIONAL SERIES

You can change the door swing from right to left hinge very easily.

1. Simply unscrew the top hinge door swing pin with an 1/8” allen

drive unit and lift door off of the bottom hinge bracket. Flip the
door, remove the light switch activator and replace the light switch
activator on the other end of the door.

2. Remove the door swing pin from bottom right hinge. Move the

bottom, right hinge bracket to the upper, left side of the cabinet
and fasten it in place with its original mounting screws.

3. Install the hinge door swing pin into the top right hinge bracket

and move the bracket to the lower left side of the cabinet. Fasten
it in place with its original screws.

4. Place the plastic washer over the bottom door swing pin on the

top surface of the bottom, left hinge.

5. Position the door on the bottom, left hinge pin and push the door

under the top, left hinge.

6. Line-up the top left hinge hole with the door bushing hole and

insert swing pin. Screw down the door swing pin with the 1/8”
allen drive unit until its head is flush with the top surface of the
top, left hinge.

7. Reposition the logo. Your installation is now complete.

Door swing pin

Top hinge
bracket

Logo

Bottom hinge

bracket

NNoottee:: HHiinnggee bbrraacckkeett llooccaattiioonn sshhoowwnn iiss ffoorr rriigghhtt--hhiinnggee sswwiinngg..

5

Light switch activator

CUSTOM WOOD FRAME INSTALLATION INSTRUCTIONS

((DDFFUURR MMooddeell))

Note: Weight of wood panel must not exceed 20 lbs.

WWoooodd SSccrreewwss

1. A #10 pan head wood screw should be used to properly secure the wood frame. A total of 8 screws will be needed
for a 3 1/2” (8.9 cm) kickplate or 7 screws for a 4” (10.2 cm) kickplate.

2. Only use pan head screws.

3. DO NOT select a screw that is longer than the wood thickness at
the screw locations.

4. Use recommended pilot holes for the frame material. (See chart)

AAsssseemmbblliinngg DDoooorr HHiinnggee BBrraacckkeettss

(Disregard if hinge brackets are already attached)

1. Attach the top and bottom door hinge brackets to the door with the #10-32 machine screws and a 1/8” allen head
driver as shown in Figure 1 below.

2. Press in the shoulder bushings to the top and bottom door hinge brackets. Make certain that the shoulder is to the
outside of the door as shown in Figure 1 below.

3. Test fit the door to the unit to make certain door will hang correctly. The door is hung correctly when the top of the
door is parallel to the top of the unit. (See Figure 2) Adjustments can be made by loosening the door hinge
machine screws and moving the door hinge brackets on the door.

4. Tighten all four (4) machine screws after adjustments have been made.

5. Remove the door from the unit by removing the units top hinge set screw and angling the door off of the bottom
hinge pin.

Figure 1

Shoulder Bushing

Door Hinge Bracket

WWoorrkkiinngg MMaatteerriiaall WWoooodd SSccrreeww SSiizzee ##1100
Hardwood 3/32 (0.24 cm)
Softwood 5/64 (0.20 cm)

Figure 2

This surface parallel to the unit.
(Right hinge door shown

#10-32 Machine

Screw

Door Hinge
Screw Holes

TTyyppiiccaall TToopp aanndd BBoottttoomm
DDoooorr HHiinnggee BBrraacckkeett
AAsssseemmbbllyy

Door Front
Surface

6

Selecting and Preparing the Wood Frame - DFUR Model

FFOORR AA 33--11//22”” TTOOEE KKIICCKK

((CCOOVVEERRSS TTHHEE EENNTTIIRREE DDOOOORR EEXXTTRRUUSSIIOONN))

1/4” X 3/8” Deep hinge screw clearance hole. Locate and drill using
door hinge hole after the door has been aligned to the unit and when
the wood is positioned on door

Min. 5/8” (1.7 cm)

ax. 3/4” (1.9 cm)

M

30 5/16”
(77.0 cm)

4 15/16”

1

36.4 cm)

(

23/32”

(1.8 cm) TYP

1 23/32” (4.4) cm min.
width to cover door
extrusion

K

AC

B

ERLAY P

V

O

7 5/32” (18.2 cm)

15./2” (1.2 cm)

F

O

W

EL

IE

N

V

A

23/32”

(1.8 cm)

TYP

Mounting surface
(Non-face) side

13/16”

7
(19.8 cm)

YP

T

15 5/32”

38.5 cm)

(

YP

T

22 1/2”

(57.2 cm)

TYP

Mounting surface

(non-face) side

Pre-drilled piolt holes ­8 places

Mounting surface
(non-face) side

1/4” X 3/8” Deep hinge screw clearance hole. Locate and drill using
door hinge hole after the door has been aligned to the unit and
when the wood is positioned on door

7

Attaching the Wood Frame to the Door - DFUR Models

1. If the door is attached to the unit, remove by unscrewing the top allen head set screw at the top hinge. Remove
the door by angling the door off of the bottom hinge pin.

2. Peel back the door gasket to expose the screw holes.

3. Set the wood frame flush to the front of the door in the desired location. Clamp the wood frame to the door if
necessary.

4. Insert the wood screws through the back of the door into the pilot holes in the wood frame and tighten.

5. Reinstall the door gasket by pressing into the door channel. Make certain the corners are inserted fully.

6. Install the door to the unit. Use the supplied plastic washer as shown in the figure below.

7. Realigning the door may be necessary. Any final door adjustments can be made using a 1/8” allen head driver to
adjust the door’s hinges. (See figure below)

8. Attach the door light striker plate as shown using the 5/16” hex or phillips head screws provided. Make certain the
light is able to turn on and off when the door is opened and closed.

9. Attach the door to the unit by reversing step number 1 above.

HHiinnggee HHaarrddwwaarree IInnssttaallllaattiioonn

DDeettaaiillss

CAUTION

Door can become

disengaged if washers

are not installed.

CAUTION

Door can become

disengaged if

washers are not

installed.

Cabinet
Hinge

(2) Nylon
hardware
components at
top hinge

5/8”x 7/32” ID washer

Magnetic door gasket

3/8” clearance holes

for frame wood screws

- 8 holes

CAUTION

Door may not swing properly

if all nylon components are

not installed as shown

Bottom Hinge Cover

Wood
Frame

Door Hinge

Shoulder bushing
3/4” OD x 7/16”
ID Washer
3/4” OD x 1/4” ID
Washer

(3) Nylon hardware
components at
bottom hinge

Door Hinge

Wood Frame

Top Hinge Cover

Shoulder
bushing

Door hinge adjustment

Attached wood

frame

Rear of Door

1/8” allen head screws for hinge
adjustment

screws

Door light striker plate

Bottom of
door

8

LEG LEVELER INSTALLATION

READ BEFORE INSTALLING LEG LEVELERS

WWAARRNNIINNGG!!

Do not lay unit on top, side, back, or front. If unit is accidentally laid in any position other than right side up, then the
unit must remain in the right side up position for at least 24 hours before plugging the unit in.

1. Tip unit backwards so there is (1) foot of clearance on front of the unit. Have someone to assist you in tilting the
unit, to prevent it from falling on you while installing the leg levelers.

2. Screw front two leg levelers into the screw impressions. Leg levelers shoudl be screwed in until snug.

3. Repeat steps 1 & 2, with the exception of tipping the unit forwards now, to screw in the back two leg levelers.

4. Your leg levelers are now installed.

5. The unit should be level from front to back and side to side. If floor conditions do not allow the unit to sit level,
adjust leg leveler(s) by turning the required leg leveler(s) counter-clockwise to increase their height and clockwise to
reduce their height.

Screw
Impressions

9

ELECTRICAL CONNECTION

EElleeccttrriiccaall SShhoocckk HHaazzaarrdd

WARNING

EElleeccttrriiccaall RReeqquuiirreemmeennttss
A 115 volt, 60 Hz, AC only 15 amp fused electrical supply is required. (A time delay
fuse or circuit breaker is recommended.) It is recommended that a separate circuit,
serving only this appliance, be provided.

••EELLEECCTTRRIICCAALL GGRROOUUNNDD IISS RREEQQUUIIRREEDD OONN TTHHIISS AAPPPPLLIIAANNCCEE..

••DDOO NNOOTT UUNNDDEERR AANNYY CCIIRRCCUUMMSSTTAANNCCEESS RREEMMOOVVEE TTHHEE PPOOWWEERR SSUUPPPPLLYY CCOORRDD

GGRROOUUNNDD PPLLUUGG..

••DDOO NNOOTT UUSSEE AANN EEXXTTEENNSSIIOONN CCOORRDD

RReeccoommmmeennddeedd GGrroouunnddiinngg MMeetthhooddss
For your personal safety, this refrigerated beverage center must be grounded. This
appliance is equipped with a 7’ (2.1m) power supply cord having a 3-prong
grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong grounding type wall
receptacle grounded in accordance with the National Electrical Code and local codes and ordinances. If the circuit does not
have a grounding type receptacle, it is the responsibility and obligation of the customer to exchange the existing receptacle in
accordance with the National Electrical Code and applicable local codes and ordinances. The third ground plug SHOULD
NOT, under any circumstances, be cut or removed. All UL listed refrigerated products are equipped with this type of plug.

FFaaiilluurree ttoo ffoollllooww tthheessee iinnssttrruuccttiioonnss ccoouulldd rreessuulltt iinn ffiirree oorr eelleeccttrriiccaall sshhoocckk..

Power Supply

with 3-prong

grounding plug

Grounding type wall
receptacle

FINAL PREPARATION

1. Some stainless steel parts may have a plastic protective wrap which must be peeled off. The interior of the refrigerated

beverage center should be washed thoroughly with hot, soapy water, rinsed and wiped dry to remove film residue and any
installation dust or debris before being used. Solutions stronger than soap and water are rarely needed.

2. All stainless steel parts should be wiped with hot soapy water. If buildup occurs, do not use steel wool, abrasive cloths,

cleaners, or powders. If it is necessary to scrape stainless steel to remove encrusted materials, soak with hot, wet cloths to
loosen the material, then use a wood or nylon scraper. Do not use a metal knife, spatula, or any other metal tool to scrape
stainless steel; scratches are almost impossible to remove.

WIRING DIAGRAM

UNDERCOUNTER 15” W. REFRIGERATED BEVERAGE CENTER

WWAARRNNIINNGG:: EELLEECCTTRRIICCAALL
GGRROOUUNNDDIINNGG
IINNSSTTRRUUCCTTIIOONNSS

This appliance is equipped with a
three prong grounding plug for
your protection against shock
hazard and should be plugged
directly into a properly grounded
three prong receptacle. Do not
cut or remove the grounding
prong from this plug.

10

OPERATING INSTRUCTIONS

SSeettttiinngg tthhee CCoonnttrroollss
The total available temperature range of the indoor unit is from 39 - 420F (4.0-- 5.60C) to 54 - 560F (12 - 130C). The total
available temperature range of the outdoor unit is from 33 - 350F (0.5-- 1.10C) to 54 - 560F (12 - 130C). The higher the number
selected, the cooler the temperature within the unit. As with any refrigerated beverage center, there is a slight temperature
variance at different locations within the cabinet. For example, the coolest area will be in the rear of the shelf above the glass
shelf. The area on the top shelf will be 3 - 70F warmer. The area in the front will be 1 - 50F warmer than the area in the rear of
the shelves. The wine section area of the refrigerated beverage center will be warmer than any other section.

To start your refrigerated beverage center, use a screwdriver to turn the control clockwise to the middle thermostat setting.
Once the refrigerated beverage center is loaded allow at least 48 hours for the unit to stabilize before making any adjustments
to the initial setting.

FOR OUTDOOR UNITS - it is recommended that in temperatures above 110oF(43.3oC) and below 40oF (4.4oC) the unit be shut
off. The normal operating range for the unit is between 60oF (15.6oC) and 100oF (37.8oC).

GGeenneerraall TTiippss aanndd SSuuggggeessttiioonnss

•After making a temperture adjustment, allow 24 hours for your refrigerated beverage center to reach a new temperature

setting.

•The motor will start and stop often. It must do this to maintain the temperature setting.

•Unplug the refrigerated beverage center before working on anything with the electrical system.

•Exercise caution when sweeping, vacuuming, or mopping near the front of the unit. Damage to the grill and/or the light

fixture switch can occur.

INTERIOR LIGHT

The interior light allows you to view your refrigerated beverage center contents. When the switch is in the “OFF” position, the
light will come on only when the door is opened. In the “ON” position, the light remains on continuously. NOTE: Outdoor
units do not have a light switch.

LIGHT ASSEMBLY REPLACEMENT

Failure to disconnect the power cord when changing the light assembly may result in

WARNING

NOTE: Please contact your Viking Range Corporation

parts distributor or dealer to order new light assembly.

To replace the light, first disconnect the refrigerated
beverage center’s power cord. Next, remove both
the green ground wire screw located on the left of the
light assembly and the other screw located on the
right of the light assembly with a 5-16” hex head
screwdriver. (See drawing). Unplug the light unit and
remove complete light assembly.

To install the new light assembly, screw in the green
ground wire screw and the screw located on the right
with a 5/16” hex head screwdriver and plug the light
unit in.

electrical shock.

Hex head

screw

Green
ground wire

Plug

Light
assembly

Hex head
screw

11

WIRE SHELVES

The adjustable wire shelves can be removed by lifting up on the shelf
slightly and sliding it out. To reinsert shelves, position the shelf over the
track and slide into place. The shelves are tapered at the back to allow
easy installation. The wine rack will hold 5 bottles of wine. The necks of
the bottles alternate front (rear facing) to back (front facing). The rack
holds three bottles facing to the rear and two bottles facing to the front.

Rear

Front

NOTE: The glass shelf separates temperature zone. Do not remove
when storing wines.

Glass shelf
separating
beverage section
from wine section

CLEANING AND MAINTENANCE

Any piece of equipment works better and lasts longer when maintained properly and kept clean.

CCoonnddeennsseerr
The condenser tubing inside the cabinet does not require frequent cleaning; however, satisfactory cooling depends on
adequate ventilation over the coils. Be sure that nothing obstructs the required air flow openings in front of the cabinet.
Spiders and insects can nest in and around the refrigerated beverage center causing damage to the unit. Frequently
brush or vacuum lint and dirt from the condenser coils for efficient performance by unscrewing the grill on the bottom
front of cabinet.

CCaabbiinneett
The cabinet can be washed with mild soap and water and thoroughly rinsed with clear water. Never use abrasive scouring
powders.

IInntteerriioorr
Wash interior compartment with mild soap and water. Do not use abrasive powder, solvent, polish cleaner or undiluted
detergent.

SSttaaiinnlleessss SStteeeell PPaarrttss
All stainless steel parts should be wiped regularly with hot soapy water. Use a liquid cleaner designed for stainless steel
when soapy water will not do the job.
or tomato juice to remain on stainless steel surfaces, as citric acid will permanently discolor stainless steel.

BBrraassss PPaarrttss
CCAAUUTTIIOONN::
PPAARRTTSS..
every day household cleaners that are not abrasive.

GGllaassss DDoooorr ((IInnddoooorr UUnniittss oonnllyy))
Use a glass cleaner or mild soap and water with soft cloth to clean the glass door. Do not use any abrasive powders. On
full overlay models, use caution when cleaning near logo area

DDoooorr GGaasskkeett
The vinyl gasket may be cleaned with mild soap and water, a baking soda and water solution, or a mild scouring powder.

All brass parts have an epoxy coating.

All brass parts should be wiped regularly with hot soapy water. When hot soapy water will not do the job, use

DDoo nnoott uussee

steel wool, abrasive cloths, cleansers, or powders. Do not permit citrus

DDOO NNOOTT UUSSEE BBRRAASSSS OORR AABBRRAASSIIVVEE CCLLEEAANNEERRSS OONN TTHHEE BBRRAASSSS

PPaaiinntteedd SSuurrffaacceess
Wash with warm soapy water.
which may damage the finish.

DDOO NNOOTT UUSSEE

steel wool, abrasive cleansers, ammonia, acids or commercial oven cleaners

12

EENNEERRGGYY SSAAVVIINNGG TTIIPPSS

•Reduce door openings.

•Close the door as soon as you can.

•Keep the condenser coils on bottom of the unit clean. (See “Cleaning and Maintenance”.)

•Adjust the temperature control to a warmer setting when practical.

•Do not put hot foods in the refrigerated beverage center.

•Install unit away from the stove or other heat sources.

TROUBLESHOOTING CHART

PPrroobblleemm PPoossssiibbllee CCaauussee//SSoolluuttiioonn
Odor in cabinet Interior needs cleaning.
Noisy operation/cabinet vibrates Cabinet not level; weak floor.
Cabinet light not working Bulb burned out; no power at outlet.
Appliance will not run Temperature control to “OFF”; line cord not plugged in; no power at

electrical outlet; house fuse blown.

Appliance runs too long Prolonged door openings; control set too cold; condenser needs

cleaning

Moisture collects inside Too many door openings; prolonged door openings; (hot, humid

weather increases condensation)

Moisture collects to outside surface Control improperly set; (Hot, humid weather increases condensation)
Interior too hot/too cold Control improperly set; faulty thermometer; (relocate thermometer to

center of cabinet and recheck)

SERVICE INFORMATION

It is assumed that your refrigerated beverage center has been properly installed in accordance with all specifications and
local codes and the appliance has been properly grounded. If your refrigerated beverage center should fail to operate,
review the troubleshooting chart before calling for service.

If service is required:

1. Call your dealer or authorized service agency. The name of the authorized service agency can be obtained from the
dealer or distributor in your area.

2. Have the following information readily available:

•Model number

•Serial number

•Date of purchase

•Name of dealer from whom purchased
If you are unable to obtain the name of an authorized service agency, or if you continue to have service problems, contact
Viking Range Corporation at [phone] or write to:

VVIIKKIINNGG PPRREEFFEERRRREEDD SSEERRVVIICCEE

111111 FFrroonntt SSttrreeeett

GGrreeeennwwoooodd,, MMiissssiissssiippppii 3388993300 UUSSAA

Record the following information indicated below. You will need it if service is ever required. The serial number and
model number for your refrigerator is located on the front of the unit at the base of the door frame.

Model Number Serial Number

Date of Purchase Date Installed

Dealer’s Name

Address

IIff sseerrvviiccee rreeqquuiirreess iinnssttaallllaattiioonn ooff ppaarrttss,, uussee oonnllyy aauutthhoorriizzeedd ppaarrttss ttoo eennssuurree pprrootteeccttiioonn uunnddeerr tthhee wwaarrrraannttyy..

TThhiiss mmaannuuaall sshhoouulldd rreemmaaiinn wwiitthh tthhee rreeffrriiggeerraattoorr ffoorr ffuuttuurree rreeffeerreennccee..

13

UNDERCOUNTER/FREESTANDING REFRIGERATED BEVERAGE CENTER WARRANTY

(Units certified for Outdoor Use)

uilt-in/freestanding undercounter refrigerated beverage centers and all of their components and accessories, except as detailed below*, are warranted to be free

B

rom defects in material or workmanship under normal household use for a period of one (1) years from the date of original retail purchase. Viking Range

f
Corporation, warrantor, agrees to repair or replace, at its option, any part which fails or is found to be defective during the warranty period.

*Painted and decorative items are warranted to be free from defective materials or workmanship for a period of ninety (90) days from the date of original retail
purchase. ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.

FFIIVVEE YYEEAARR LLIIMMIITTEEDD WWAARRRRAANNTTYY

ny sealed refrigeration system component, as listed below, is warranted to be free from defective materials or workmanship in normal household use during the

A

econd through the fifth year from the date of original retail purchase. Viking Range Corporation, warrantor, agrees to repair or replace, at its option, any part which

s
fails or is found to be defective during the warranty period.

OONNEE YYEEAARR FFUULLLL WWAARRRRAANNTTYY

SSeeaalleedd RReeffrriiggeerraattiioonn SSyysstteemm CCoommppoonneennttss::

It is recommended that in temperatures above 100

o

15.6

(

F

NNIINNEETTYY ((9900)) DDAAYY RREESSIIDDEENNTTIIAALL PPLLUUSS WWAARRRRAANNTTYY
Examples are, but not limited to, bed and breakfasts, fire stations, private clubs, churches, etc. This warranty excludes all commercial locations such as

estaurants, food service locations and institutional food service locations.

r

This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty.

This warranty shall apply to products purchased and located in the United States and Canada. Products must be purchased in the country where service is
requested. Warranty labor shall be performed by an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage
resulting from abuse, accident, natural disaster, loss of electrical power to the product for any reason, alteration, improper installation, improper operation or repair or
service to the product by anyone other than an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting
from indoor units being used in outdoor situations. This warranty does not apply to commercial usage.
damage whether arising out of breach of warranty, breach of contract, or otherwise. Some jurisdictions do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation or exclusion may not apply to you.

) and 100

o

F

(37.7

o

).

C

ompressor, Evaporator, Condenser, Connecting Tubing, Dryer/Strainer

C

o

F (37.8oC) and below 40oF (4.4oC) the unit be shut off. The normal operating range for the unit is between 60oF

This warranty applies to applications where use of the product extends beyond normal residential use.

Warrantor is not responsible for consequential or incidental

Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof of purchase upon request, and making the appliance
reasonably accessible for service. If the product or one of its component parts contains a defect or malfunction during the warranty period, after a reasonable
number of attempts by the warrantor to remedy the defects or malfunctions, the owner is entitled to either a refund or replacement of the product or its component
part or parts. Replacement of a component part includes its free installation. Warrantor’s liability on any claim of any kind, with respect to the goods or services
covered hereunder, shall in no case exceed the price of the goods or service or part there of which gives rise to the claim.

WWAARRRRAANNTTYY SSEERRVVIICCEE::
representative. Service will be provided during normal business hours, and labor performed at overtime or premium rates shall not be covered by this warranty. To
obtain warranty service, contact the dealer from whom the product was purchased, an authorized Viking Range Corporation service agent, or Viking Range
Corporation. Provide model and serial number and date of original purchase. For the name of your nearest authorized Viking Range Corporation service agency,
call the dealer from whom the product was purchased or Viking Range Corporation.

The return of the Owner Registration Card is not a condition of warranty coverage. You, however, should return the Owner Registration Card so that Viking Range
Corporation can contact you should any question of safety arise which could affect you.

Any implied warranties of merchantability and fitness applicable to the above described undercounter refrigerated beverage center are limited in duration to the
period of coverage of the applicable express written limited warranties set forth above. Some jurisdictions do not allow limitations on how long an implied warranty
lasts, so the above limitation may not apply to you. This warranty gives you specific rights, and you may also have other rights which may vary from jurisdiction to
jurisdiction.

Under the terms of this warranty, service must be performed by a factory authorized Viking Range Corporation service agent or

IIMMPPOORRTTAANNTT::

Retain proof of original purchase to establish warranty period.

14

UNDERCOUNTER/FREESTANDING REFRIGERATED BEVERAGE CENTER WARRANTY

(Units certified for Indoor Use)

Built-in/freestanding undercounter refrigerated beverage centers and all of their components and accessories, except as detailed below*, are warranted to be free from
defects in material or workmanship under normal household use for a period of two (2) years from the date of original retail purchase. Viking Range Corporation,

arrantor, agrees to repair or replace, at its option, any part which fails or is found to be defective during the warranty period

w

*Painted and decorative items are warranted to be free from defective materials or workmanship for a period of ninety (90) days from the date of original retail

urchase. ANY DEFECTS MUST BE REPORTED TO THE SELLING DEALER WITHIN NINETY (90) DAYS FROM DATE OF ORIGINAL RETAIL PURCHASE.

p

SSIIXX YYEEAARR FFUULLLL WWAARRRRAANNTTYY

TTWWOO YYEEAARR FFUULLLL WWAARRRRAANNTTYY

Any sealed refrigeration system component, as listed below, is warranted to be free from defective materials or workmanship in normal household use during the third

hrough the sixth year from the date of original retail purchase. Viking Range Corporation, warrantor, agrees to repair or replace, at its option, any part which fails or is

t
found to be defective during the warranty period.
SSeeaalleedd RReeffrriiggeerraattiioonn SSyysstteemm CCoommppoonneennttss::

Compressor, Evaporator, Condenser, Connecting Tubing, Dryer/Strainer

TTWWEELLVVEE YYEEAARR LLIIMMIITTEEDD WWAARRRRAANNTTYY

Any sealed refrigeration system component, as listed above, which fails due to defective materials or workmanship in normal household use during the seventh
through the twelfth year from the date of original retail purchase will be repaired or replaced, free of charge for the part itself, with the owner paying all other costs,

ncluding labor.

i

NNIINNEETTYY ((9900)) DDAAYY RREESSIIDDEENNTTIIAALL PPLLUUSS WWAARRRRAANNTTYY

xamples are, but not limited to, bed and breakfasts, fire stations, private clubs, churches, etc. This warranty excludes all commercial locations such as

E
restaurants, food service locations and institutional food service locations.

This warranty extends to the original purchaser of the product warranted hereunder and to each transferee owner of the product during the term of the warranty.

This warranty shall apply to products purchased and located in the United States and Canada. Products must be purchased in the country where service is requested.
Warranty labor shall be performed by an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting from
abuse, accident, natural disaster, loss of electrical power to the product for any reason, alteration, improper installation, improper operation or repair or service to the
product by anyone other than an authorized Viking Range Corporation service agency or representative. Warranty shall not apply to damage resulting from indoor
units being used in outdoor situations. This warranty does not apply to commercial usage.
whether arising out of breach of warranty, breach of contract, or otherwise. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitation or exclusion may not apply to you.

This warranty applies to applications where use of the product extends beyond normal residential use.

Warrantor is not responsible for consequential or incidental damage

Owner shall be responsible for proper installation, providing normal care and maintenance, providing proof of purchase upon request, and making the appliance
reasonably accessible for service. If the product or one of its component parts contains a defect or malfunction during the warranty period, after a reasonable number
of attempts by the warrantor to remedy the defects or malfunctions, the owner is entitled to either a refund or replacement of the product or its component part or
parts. Replacement of a component part includes its free installation. Warrantor’s liability on any claim of any kind, with respect to the goods or services covered
hereunder, shall in no case exceed the price of the goods or service or part there of which gives rise to the claim.

WWAARRRRAANNTTYY SSEERRVVIICCEE::
Service will be provided during normal business hours, and labor performed at overtime or premium rates shall not be covered by this warranty. To obtain warranty
service, contact the dealer from whom the product was purchased, an authorized Viking Range Corporation service agent, or Viking Range Corporation. Provide
model and serial number and date of original purchase. For the name of your nearest authorized Viking Range Corporation service agency, call the dealer from whom
the product was purchased or Viking Range Corporation.

The return of the Owner Registration Card is not a condition of warranty coverage.
Corporation can contact you should any question of safety arise which could affect you.

Any implied warranties of merchantability and fitness applicable to the above described undercounter refrigerator are limited in duration to the period of coverage of
the applicable express written limited warranties set forth above. Some jurisdictions do not allow limitations on how long an implied warranty lasts, so the above
limitation may not apply to you. This warranty gives you specific rights, and you may also have other rights which may vary from jurisdiction to jurisdiction.

Under the terms of this warranty, service must be performed by a factory authorized Viking Range Corporation service agent or representative.

IIMMPPOORRTTAANNTT::

Retain proof of original purchase to establish warranty period.

You, however, should return the Owner Registration Card so that Viking Range

Viking Range Corporation

111 Front Street • Greenwood, Mississippi USA • 38930 [phone]

www.vikingrange.com

Specifications subject to change without notice

F20343B (062007J)