Viking VCSO210 Installation Manual

Viking Installation Guide

IMPORTANT–Please Read and Follow!

• Before beginning, please read these instructions completely and carefully.

• Be sure to DISCONNECT THE PLUG of the microwave oven from the electrical outlet before installing the built-in trim kit.

Remove the turntable from the oven cavity.

• Because the kit includes metal parts, caution should be used in handling and installation to avoid the possibility of injury.

• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.

• Please observe all local and national codes and ordinances.

• Theinstallershouldleavethese instructions with the consumerwho should retain for local inspector’s use and for
futurereference.

• This built-in trim kit is designed for use ONLY WITH VIKING COMBI STEAM/CONVECT™ OVEN.

• Your oven can be built into a cabinet or wall or above any electric wall oven, gas wall oven or warming drawer.

• NOTE: The bottom of the cut-out opening for built-in use must be 36 inches (915 mm) or higher from the floor.

• The electrical requirements for this oven are 120 volts, 15 amps. The oven has a 5-15 plug and requires a 5-15 receptacle.

• PLEASE READ THESE INSTRUCTIONS THOROUGHLY BEFORE BEGINNING INSTALLATION!

Cabinet or wall opening

Built-in kit frame assembly

Combi Steam/Convect™ Oven

HEIGHT WIDTH DEPTH

19" - 19 1/8"

(482 mm - 486 mm)

22 1/8"

(562.1 mm)

17 1/4"

(438 mm)

28"

(712 mm)

29 1/2"

(749.3 mm)

21 3/4"

(553 mm)

(509.5 mm minimum)

23 1/4" minimum

18 3/8"

(468 mm)

Combi Steam/Convect™ Oven and Built-In Trim Kit

111 Front Street

Greenwood, Mississippi 38930 USA

Provided Parts

Parts Included in VTKS300 kits

Exhaus t Duct Back

QtY 1

DiviD E PlatE l

QtY 1

Ex haus t Duc t Bot tom

PartName Qty

Exhaust Duct Back
PDUC-B107WRWZ

Exhaust Duct Upper
PDUC-B105WRWZ

Divide Plate L
PSKR-A486WRWZ

Divide Plate R
PSKR-A487WRWZ

Rectifier Plate L
PSKR-A484WRWZ

Exhaust Duct Lef t
PDUC-B108WRWZ

Exhaust Duct Right
PDUC-B117WRWZ

Exhaust Duct Bottom
PDUC-B106WRWZ

Frame Assembly
DDECAB012MRK0

QtY 1

Exhaus t Duct uPPER

QtY 1

DiviD E PlatE R

QtY 1

1

1

1

1

1

1

1

1

1

REctifi ER PlatE l

QtY 1

REaR sPacER

QtY 1

fRamE assEmBlY

QtY 1

Screw (A)
XHTS740P08000

Screw (B)
XMMS841P13000

Rear Spacer
PSPAFA003WRWZ

Cushion 1 5/8" x 16", 15 mm x 405 mm
PCUS-A245WRPZ

Cushion 2 1/4" x 24-3/8", 5 mm x 618 mm
PCUS-A247WRPZ

Cushion 3 1-1/8" x 27-1/8", 30 mm x 689 mm
PCUS-A249WRPZ

Cushion 4 1/4" x 12", 5 mm x 305 mm
PCUS-A251WRPZ

Cushion 5 1/4" x 15", 5 mm x 382 mm
PCUS-A253WRPZ

Exh aust

Duct lEf t

QtY 1

scREw a - sh oRt

Exh aust

Duct Ri Ght

QtY 1

QtY 23

scREw B - loN G

QtY 8

PartName Qty

23

8

1

1

1

1

1

1

E2

Preparation

Follow the directions from 1 to 5 to attach cushions to some parts.

CUSHIONS 1

1

CUSHIONS 1

3

3. EXHAUST DUCT BOTTOM

Remove the backing paper from CUSHION 3. Attach the CUSHIONS
3 to the EXHAUST DUCT BOTTOM as shown in the Figure 3.

* Start A to attach the CUSHION.

A

CUSHIONS 3

1. EXHAUST DUCT UPPER

Remove the backing paper from each CUSHION 1. Attach the
CUSHIONS 1 to each side flange of the EXHAUST DUCT UPPER as
shown in the Figure 1.

2

CUSHIONS 2

2. EXHAUST DUCT BACK

Remove the backing paper from CUSHION 2. Attach the CUSHIONS
2 at the lower flange of the EXHAUST DUCT BACK as shown in the

Figure 2.

4

CUSHIONS 4

4. DIVIDE PLATE L

Remove the backing paper from CUSHION 4. Attach the CUSHIONS
4 to the DIVIDE PLATE L as shown in the Figure 4.

CUSHIONS 5

5

5. DIVIDE PLATE R

Remove the backing paper from CUSHION 5. Attach the CUSHIONS
5 to the DIVIDE PLATE R as shown in the Figure 5.

E3