Page 1
Viking Installation Guide
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
F20713 EN
Professional & Designer Freestanding
Refrigeration Side Trim, Side Panel,
Top Panel & Grille Installation
(012010)
Page 2
3
4
A
A
B
Left Shim
Trim
Left SideTrim
Right Shim
Trim
Right Side
Trim
Front Grille
Adhesive
Tape
Screws
Grille Spacer
L-Bracket Right
L-Bracket Left
1
2
5
1
2
Specifications
Professional & Designer
Freestanding Refrigerators
Description VCSF/DDSF136D with side panels/tops/grilles
Overall width with side panels 35-7/8” (91.1 cm)
Overall height with tops/grilles 71-7/8” (182.6 cm)
Cutout width with side panels 36” (91.4 cm)
Cutout height with tops/grilles 72” (182.9 cm)
Installation - Side Trim and Grille
(Built-In Installation) (cont.)
Required Components
Remove and discard screw and hinge cover, if
applicable.
Remove edge of corner cover.
Attach brackets and spacers, included in the kit, to the
grille assembly with four A screws.
Apply adhesive tape to grille assembly.
Remove adhesive backing. Firmly press the grille
assembly down so the adhesive adheres to the cabinet.
Align grille assembly to front door and position grille
on top of unit.
2
3
Page 3
1
Left Panel Right Panel
Top Panel
Front Grille
Caps
A
B
Screws
C
2
A
A - Designer Series
B - Pro Series
3
2
1
4
5
Installation - Side Trim and Grille
6
B
7
7
2
”
8
2
2
1
9
2
2
1
complete
Installation - Side Panel, Top Panel and Grille
(Built-In Installation) (cont.)
Secure the grille brackets to the holes in the hinge
plate with two B screws.
Raise the unit up until the measurement from the floor
to the top of the grille assembly is 72 inches or 6 feet.
(Wrapped Installation)
Required Components
Remove and discard screw and hinge cover, if
applicable. (Repeat if two hinges are used.)
Shim trim has adhesive backing on both sides. Remove adhesive
backing on refrigerator side only. Fit the shim trim to the front of the
unit first. Locate the top of the shim trim with the top of the
refrigerator cabinet
.
Remove adhesive backing for the side trim. Locate the
top of the side trim with the top of the grille assembly.
Press the side trim into the refrigerator cabinet at the
center location.
Remove edge of corner cover.
Remove adhesive backing from the side panel. Fit the
side panel to the front of the unit first.
With top panel and grille upside down, position grille
assembly in front of top panel. Secure top panel to grille
assembly via four outer holes and three inner holes.
Attach rear of side panels with screws.
NOTE: The holes on the side panel are clearance holes.
54
Page 4
Installation - Side Panel, Top Panel and Grille
6
1
2
2
7
8
C
9
10
complete
(Wrapped Installation) (cont.)
Remove adhesive backing from other side panel. Fit the
side panel to the front of the unit first. Spacer on top of
side panel needs to sit on top of refrigerator cabinet.
Align top panel and grille assembly to front door and
position top panel and grille on top of unit.
Attach rear of side panels with screws.
NOTE: The holes on the side panel are clearance holes.
Insert screws through holes of top panel into side
panel.
Insert cap covers into holes.
76
Loading...