Viking ES-1 Technical Practice

ES-1

ES-1

Stand Alone Door

Controller Entry System

February 15, 2005

iinnffoo@@vviikkiinnggeelleeccttrroonniiccss..ccoom

m

hhttttpp::////wwwwww..vviikkiinnggeelleeccttrroonniiccss..ccoom

m

Power: 120V AC/12V DC 500mA, UL listed adapter provided or
use any 12-24V AC or DC source @ 100mA (designed to share
power with the door strike’s power supply)

Dimensions: 133mm x 89mm x 44mm (5.25” x 3.5” x 1.75”)
Shipping Weight: 1.3 kg (3 lbs)
Environmental: 0° C to 32° C (32° F to 90° F) with 5% to 95%

non-condensing humidity

Relay Contact Ratings: 5A @ 30V DC/250V AC maximum
Maximum Wiegand Length: 732m (2000 ft) - 24 AWG
Maximum LOG BUS Length: 1610m (5280 ft - 1 mile), 24 AWG
Connections: 11 screw terminals, (1) RJ-11 telco jack

Add Keyless Entry and/or Card Reader Entry

for a Single Door with Up to 250 Users

The ES-1 is a door controller designed to operate a
door strike or magnetic lock upon receiving a valid
card read and/or keyless entry code from Wiegand
devices. One ES-1, one or two Wiegand devices and
a door strike or magnetic lock of your choice is
required for each entry point.

The Wiegand device used may be the Viking model
HID-1 Proximity Card Reader and/or the Viking
model HID-2 Wiegand Output Keypad or any other
card reader, RF transmitter or digital keypad that out­puts the 26 bit Wiegand format. If two Wiegand

devices are used, one can be placed on each side of
a doorway to control access in both directions (entry and exit). Up to 250 valid Wiegand codes
can be programmed into the ES-1.

Other programmable parameters, like relay activation, mode (normal, off, or open) and facility
codes are also stored in non-volatile memory. All programming is done with a local touch tone
phone. Up to three ES-1s can be programmed simultaneously if they will be sharing all the
same programming codes and parameters. Entry logging is possible with the ES-1’s log bus
data output.

PPrraaccttiicce

e

T

T

EELLEECCOOM

M

S

S

OOLLUUTTIIOONNSSFFOORRTTHHE

E

221

1

SST

T

C

C

EENNTTUURRY

Y

TECHNICAL

TECHNICAL

SSppeecciiffiiccaattiioonns

s

FFeeaattuurrees

s

• Up to 250 tenants

• Program and control with a Touch Tone phone

• Use with any 26 bit Wiegand device

• Supports 1 entry point

• Compatible with Viking models HID-1 and HID-2

• Non-volatile memory (no batteries required)

• LOG BUS data output for logging entry events

• Card plus keypad mode for highest security

• One time codes for visitors

• Bi-directional (entry and exit) control

PPhhoonnee......771155..338866..8888661

1

AApppplliiccaattiioonns

s

• Business entrances

• High rise apartment buildings

• Condos

• Senior citizen buildings

• Assisted care centers

• Retirement homes

• Gated communities

IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT [phone]

Our Technical Support Department is available for assistance Monday 8am-4pm and Tuesday-Friday 8am - 5pm central time. So that we can give you better service, before you call please:

1. Know the model number, the serial number and what software version you have (see serial label).

2. Have your Technical Practice in front of you.

3. It is best if you are on site.

WARRANTY

Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manu­factured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's
Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.

This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others.

Vikings sole responsibility shall be to repair or replace (at Viking's option) the material within the terms stated above. VIKING SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY KIND INCLUDING INCIDENTAL OR CONSE­QUENTIAL DAMAGES RESULTING DIRECTLY OR INDIRECTLY FROM ANY BREACH OF ANY WARRANTY EXPRESSED OR IMPLIED, OR FOR ANY OTHER FAILURE OF THIS PRODUCT. Some states do not allow the exclusion or limi­tation of incidental or consequential damages, so this limitation may not apply to you.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, WHICH ARE HEREBY EXCLUDED
BEYOND THE ONE YEAR DURATION OF THIS WARRANTY. Some states do not allow limitation on how long an implied warranty lasts, so the above limitation may not apply to you.

RETURNING PRODUCT FOR EXCHANGE

The following procedure is for equipment that has failed out-of-box (within 10 days of purchase

):

1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The

customer MUST be able to step through recommended tests for diagnosis.

2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input
and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14)
calendar days from the date of issue.

3. After obtaining the R.A. number, return the approved equipment to your distributor

, referencing the R.A. number. Your
distributor will then replace the product over the counter at no charge. The distributor will then return the product to
Viking using the same R.A. number.

4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't
followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.

RETURNING PRODUCT FOR REPAIR

The following procedure is for equipment that needs repair:

1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)

number. The customer MUST have a complete description of the problem, with all pertinent information regarding the
defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.

2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static
sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individual­ly boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include
ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to:

Viking Electronics, 1531 Industrial Street, Hudson, WI 54016

3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.

4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.

DDeeffiinniittiioonns

s

26 Bit Wiegand Format: The industry standard data output of access control card readers.

Bi-Directional Access: Two Wiegand devices can be wired in parallel to one ES-1 to control access in both

directions at a single entry point. Simply place one card reader on each side of the door or gate. When either
one detects a valid code, the ES-1 will strike the door. Data logging will not be able to distinguish the direction
of the access. If that is a requirement, two separate ES-1s will need to be installed, so each one can log sepa­rate access events from each side of the door.

Card Plus Keypad Mode: This is a higher security mode in which a valid card + a valid keypad entry is required
to gain access.

Entry Code: The number that when it matches either a Keyless Entry or a Proxy Card number, allows access.
Each tenant may have their own unique Entry Code that is easily changed or removed when a tenant moves
out.

Entry Point: A door or gate allowing access into a secure or controlled area.

Facility Code: A 3-digit number that each proxy card contains in order to provide greater security. Usually the

cards used at a given building all have the same facility code.

Keyless Entry: A way for tenants to let themselves in, by entering their entry code on a keypad.

LOG BUS: A two wire data bus that can be wired in parallel with additional ES-1 log busses. Data is sent as

1200 baud ASCII characters at TTL levels (0-5 Volt). Any RS-232 port designed to receive TTL levels can receive
log bus data directly on the “Receive Data” and “Signal Ground” pins.

Memory Location: The number used when programming, that stores the location of an entry code.

One Time Code: An entry code that can only be used once - this feature is handy for visitors. Once the code
is used the ES-1 forgets it.

Proxy Card: A credit size card that identifies itself when within close proximity of a reader. Card “swiping” is not

necessary. The card contains a 3 digit Facility Code, a 5 digit Internal Card number and a 5 digit External Printed
number, that may or may not match the Internal number.

Proxy Card Reader: A device used to read the data from a Proxy Card when its held within a few inches of the
reader.

IInnssttaallllaattiioon

n

IMPORTANT: Electronic devices are susceptible to lightning and power station electrical surges from both the AC outlet and the

telephone line. It is recommended that a surge protector be installed to protect against such surges. Contact Panamax at (800)
472-5555 or Electronic Specialists Inc. at [phone].

!

* Note: Maximum Wiegand run length is 2000 feet using 24 gauge wire when using the Viking Model HID-1 proxy card reader, and 4000
feet for the HID-2 keypad. Run length is reduced in half if two share the same wire run from the same ES-1 entry point. Run length will
also be reduced if using a Wiegand device other than the Viking Model HID-1, that requires more than 35mA average operating current.
Run lengths can be doubled by doubling up on the BLACK and RED 24 gauge wire, or using 21 gauge (or larger) wire. Certain electri­cally noisy locations might require shielded wire.

A. Basic Wiring

B. Gang Programming Wiring

A basic door access controlled entry point is wired as shown below. The relay can be connected as either Normally
Open, or Normally Closed. All 26-bit Wiegand devices are fully supported (power and data) from the ES-1 and can be
installed up to 500 feet away using 24 gauge wire. Viking Wiegand devices can run even further (see Note above).
The ES-1 can support either a card reader (Viking model HID-1) or a keyless entry keypad (Viking model HID-2), or
both. If both are installed, the “Card Plus Keypad” mode can be used. If any two Wiegand devices are used, one can
be placed on each side of a doorway/gate for bi-directional (entry and exit) access control.

If multiply ES-1s are installed to handle door access control for multiple entry points, two or three of them can be pro­grammed simultaneously if they are to be programmed identically. Do this by wiring GANG PROG COMM screw ter­minals 1 together, and screw terminals 2 together. The touch tone programming phone connected to any one of them
will program all of them simultaneously.

?

Need More Information on the HID-2?

Call [phone] and select 199.

?

Need More Information on the HID-1?

Call [phone] and select 197.

©

MODEL ES-1

VIKING

ELECTRONICS

HUDSON, WI 54016

STAND-ALONE

DOOR CONTROLLER

ENTRY SYSTEM

GANG
PROG

LOG

COMM

BUS

ENTRY POINT

WIEGAND

DEVICE

BLK

RED

GRN

WHT

Doorstrike

Power Supply

5A@30VDC/250VAC

maximum

(not included)

12V DC
Adapter

Included

or

VIKING

POWER 12 VDC

Viking HID-2

Keypad

(not included)

(Power typically not

required for gate

Doorstrike/Magnetic Lock

(not included)

PROGRAM

PHONE

1219m (4000 ft) maximum

controllers.)

Remote Touch Tone

Programming Phone

RAD-1 Remote Access

Device (not included)

Touch Tone

Programming Phone

609m (2000 ft) maximum

Viking HID-1

and/or

Proximity Card

Reader

or

(not included)

Touch Tone

Programming

Phone

VIKING

DOOR CONTROLLER

POWER 12 VDC

PROGRAM

PHONE

ENTRY SYSTEM

©

VIKING

ELECTRONICS

HUDSON, WI 54016

STAND-ALONE

GANG

LOG

PROG

BUS

COMM

1 2

MODEL ES-1

ENTRY POINT

WIEGAND

DEVICE

BLK

RED

WHT

GRN

609m (2000 ft) maximum

with 24 gauge wire

VIKING

DOOR CONTROLLER

POWER 12 VDC

PROGRAM

PHONE

©

MODEL ES-1

VIKING

ELECTRONICS

HUDSON, WI 54016

STAND-ALONE

ENTRY SYSTEM

LOG
BUS

GANG
PROG

COMM

ENTRY POINT

WIEGAND

DEVICE

BLK

RED

GRN

WHT

1 2 1 2

609m (2000 ft) maximum

with 24 gauge wire

VIKING

POWER 12 VDC

PROGRAM

PHONE

©

MODEL ES-1

VIKING

ELECTRONICS

HUDSON, WI 54016

STAND-ALONE

DOOR CONTROLLER

ENTRY SYSTEM

GANG

LOG

PROG

BUS

COMM

ENTRY POINT

WIEGAND

DEVICE

BLK

RED

GRN

WHT