Viking E-1600-22-IP, E-1600-22-IPEWP Quick Start Manual
E-1600-22-IP or
E-1600-22-IPEWP
VoIP Emergency Phone
September 20, 2018
QUICK START GUIDE
VIKING
Electronics, Inc.
K See Product Manual for complete installation and programming instructions.
1.0 Out-of-Box
1.1 Verify that you have received all of the parts listed
1.2 Download the product manual
1. Go to www.vikingelectronics.com and
enter E-1600-22-IP in the search box
2. Click E-1600-22-IP in the search results
3. Click Product Manual to open and
download the PDF
1.3 Download and install the programming software
1. Go to www.vikingelectronics.com and enter E-1600-22-IP in the search box
2. Click E-1600-22-IP in the search results
3. Scroll down the page to Downloads, click IP Programming Software
4. Install the programming software by saving or opening the file and then clicking on
setup Viking IP Programming.exe
5. Follow the prompts on your screen to complete software installation
2.0 Power Source
Select PoE Switch or PoE Injector that meets the following requirements:
1. IEEE 802.3af / 802.3at / 802.3bu compliant
2. Capable of providing at least 4 Watts (class 1)
Note: CAT5e (or higher) cable recommended
X 1
E-1600-22-IP or E-1600-22IPEWP Emergency Phone
X 1
Torx T-10 Security Bit
X 3
Gel-Filled Butt Connectors
X 1
Faceplate Gasket
X 4
6-32 x 3/4” Flat Head Torx
Drive Screws
Scan the QR code to
open and download
the product manual
- OR -
4.0 Features Overview
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries
assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
See the Product Manual for complete installation and programming instructions.
Questions? Call Viking Product Support: 715-386-8666
E-1600-22-IP Quick Start Guide ZF303602 REV A
• Make sure the port is not in trunk mode
• Make sure port is capable of 100mbps full duplex
• Disable Spanning Tree Protocol (STP) or enable Portfast
3.0 Network Port Settings
Note: The gel-filled (water-tight) butt connectors are designed for insulation displacement on 19-26 gauge wire with a
maximum insulation of 0.082 inches. Cut off stripped wire ends before terminating.
Rear (PCB) View of E-1600-IP Series
Emergency Phone
Green Unit Status LED
Yellow Network Status LED:
Lights steady to indicate power
and data link. Blinks to indicate
network activity.
Connect to Optional
Strobe Light, LV-1K, etc.
18E80FXXXXXX
asdesaxtff
MAC:
PoE LAN Port 10/100, PoE
Class 1 (<4 Watts): Connect
to your LAN via RJ45 plug
and CAT5 or greater twisted
pair wire.
MAC Address Label: The
MAC address is a unique 12
digit number used by routers
to send network traffic to the
correct IP address.
Viking model
LV-1K shown
(not included),
see DOD 246
- OR -
Viking model
SL-2 shown
(not included),
see DOD 242
Optional 2 Amp Relay
Output Contacts
(2A@30VDC/ 250VAC max)
N.C. (Gray)
COM. (Blue)
N.O. (Yellow)
3 Gel-Filled Butt
Connectors (included)
- Black
+ Red
Black
Black
Yellow
Yellow
- Black
+ Red
Red
Red
LED
Help Switch
Info Switch
Speaker
Microphone
Loading...