Viking DTWS, DTWN User Manual

Page 1
VENTILATION
Designer Built-In Wall Hoods
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
All models include
Standard Features & Accessories
ORDERING INSTRUCTIONS
First specify model number, followed by color code (DTWS3049SS). Specify decorative rail code at end (DTWS3049SSCR).
• Must also purchase interior or exterior ventilator kit, sold separately (see Installation Notes & Accessories for recommended Viking ventilator products
• 24”D.(tests show 24”D. hoods perform properly over 27”D. ranges)
• Heat sensor turns the ventilator on full power when cooking temperatures reach uncomfortable levels
• Variable speed controls for custom venting—separate on/off switch allows you to leave ventilator at favorite/most-used setting
• 12-hour timer built into ventilator controls
• Delay feature allows you to set the ventilator to shut off on its own from 10 – 30 minutes later
• Heavy-duty construction; elegant design, and styling o Virtually seamless stainless steel
design with no visible screws
• Easy cleanup o Dishwasher-safe, stainless steel
mesh filters efficiently remove grease and heated vapors from the
air, and are easily removed for quick cleaning (frame and mesh are stainless steel for durability and long life)
See Dimensions & Specifications
table for number of filters (and spacers) per model
o Design of low-profile filter system
means less interior hood space to be cleaned
o Canopy interior is completely lined
in stainless steel for increased rigidity, seamless appearance, and easy cleaning
• 50-watt halogen lights with dimmer control o Power switch and dimmer control
are separate, allowing you to leave dimmer at favorite position
o See Dimensions & Specifications
table for number of lights per model
DTWS models include
• 9"H.
• Adjustable duct cover (for 8 – 9’ ceilings) shipped standard (see Dimensions & Specifications table) o Finish matches canopy exterior
DTWN models include
• 18"H.
• Duct covers must be ordered separately (see Installation Notes & Accessories)
Model numbers
SLIM TRADITIONAL WALL HOODS
• DTWS3049—30"W.
• DTWS3649—36"W.
• DTWS4249—42"W.
• DTWS4849—48"W.
TALL TRADITIONAL LEGDELESS WALL HOODS
• DTWN3048—30"W.
• DTWN3648—36"W.
• DTWN4248—42"W.
• DTWN4848—48"W.
Slim Traditional Wall Hoods should not be installed over Professional cooking products with the gas Char-Grill feature. A 1,200 or 1,500 CFM (if applicable) ventilator kit should be used when installed over ranges/rangetops with gas grill.
EXTRA FINISH DETAILS FOR DTWS MODELS ONLY
• Accessory Rail—along front of canopy (must be ordered and factory installed)
• Stainless Steel/Chrome (CR)—Stainless steel rail with chrome supports/brackets and hooks (included)
• Brass Trim Option (BR)—nameplate, rail, supports/brackets, and hooks (included). Brass components have a durable protective coating for maintenance-free normal use.
FINISH DETAILS FOR ALL MODELS
• Stainless Steel (SS), Black (BK), White (WH), Metallic Silver (MS), Graphite Gray (GG), Stone Gray (SG), Taupe (TP), Biscuit (BT), Cotton White (CW), Oyster Gray (OG), Golden Mist (GM), Lemonade (LE), Sage (SA), Mint Julep (MJ), Sea Glass (SE), Iridescent Blue (IB), Viking Blue (VB), Pumpkin (PM), Racing Red (RR), Apple Red (AR), Burgundy (BU), Plum (PL), Chocolate (CH), and Cobalt Blue (CB).
• Finish designates exterior of canopy
• Stainless Steel (SS) canopy interior
DTWS Slim Traditional
Wall Hood*
Model Options
DTWN Tall Traditional
Ledgeless Wall Hood**
Page 2
24”
(61.0
cm)
A
9”
(22.9 cm)
C
B
12”
(30.5 cm)
2 ”
(5.1 cm)
VENTILATION
Designer Built-In Wall Hoods
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
Please see
Installation Notes &
Accessories for
important information,
including ventilator
kits, duct covers,
backsplashes, and
warming shelf
panels.
Dimensions & Specifications
PRODUCT DIMENSIONS
DTWS Slim Traditional
Wall Hood
SLIM TRADITIONAL WALL HOOD
DTWN Tall
Traditional Ledgeless
Wall Hood
24”
(61.0 cm)
A
B
18”
(45.7 cm)
12”
(30.5 cm
)
12”
(30.5 cm)
TALL TRADITIONAL LEDGELESS WALL HOOD
Model Hood Duct Cover Lights Filters Heat Approx.
Width (A) Height Width (B) Depth Height (C) Lamps Ship. wt.
DTWS3049 29-7/8” (75.9 cm) 9” (22.9 cm) 12” (30.5 cm) 12” (30.5 cm) 21” (53.3cm)— 2 2 N/A 50 lbs.
33” (83.8 cm) (22.5 kg)
DTWS3649 35-7/8” (91.1 cm) 9” (22.9 cm) 12” (30.5 cm) 12” (30.5 cm) 21” (53.3cm)— 2 2 N/A 60 lbs.
33” (83.8 cm) (27.0 kg)
DTWS4249 41-7/8” (106.4 cm) 9” (22.9 cm) 12” (30.5 cm) 12” (30.5 cm) 21” (53.3cm)— 2 3 N/A 70 lbs.
33” (83.8 cm) (31.5 kg)
DTWS4849 47-7/8” (121.6 cm) 9” (22.9 cm) 20” (50.8 cm) 12” (30.5 cm) 21” (53.3cm)— 3 3 N/A 81 lbs.
33” (83.8 cm) (36.5 kg)
DTWN3048 29-7/8” (75.9 cm) 18” (45.7 cm) 29-7/8 12” (30.5 cm) 12” (30.5 cm) 2 2 N/A 59 lbs.
(75.9 cm) (26.6 kg)
DTWN3648 35-7/8” (91.1 cm) 18” (45.7 cm) 35-7/8” 12” (30.5 cm) 12” (30.5 cm) 2 2 N/A 69 lbs.
(91.1 cm) (31.1 kg
DTWN4248 41-7/8” (106.4 cm) 18” (45.7 cm) 41-7/8” 12” (30.5 cm) 12” (30.5 cm) 2 3 N/A 79 lbs.
(106.4 cm) (35.6 kg)
DTWN4848 47-7/8” (121.6 cm) 18” (45.7 cm) 47-7/8” 12” (30.5 cm) 12” (30.5 cm) 3 3 N/A 90 lbs.
(121.6cm) (40.5 kg)
Page 3
66”min.
(167.6 cm)
to
72”max.
(182.9 cm)
30”min.
(76.2 cm)
to
36”max.
(91.4 cm)
36”
(91.4 cm)
VENTILATION
Designer Built-In Wall Hoods
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
Dimensions & Specifications
CLEARANCE DIMENSIONS
30”min.
(76.2 c
m)
to
36”max.
(91.4 cm)
66”min.
(167.6 cm)
to
72”max.
(182.9 cm)
36”
(91.4 cm)
TALL TRADITIONAL LEDGELESS WALL HOOD
SLIM TRADITIONAL WALL HOOD
Page 4
Proper installation/ducting is extremely important to ensure maximum performance. Use a qualified and trained installer.
DUCTING
• Check with a qualified and trained installer or local codes for makeup air requirements, if any.
• Max. duct run length o For 300 – 1,200 CFM—50’
(152.4 m)
o For 1,500 CFM—75’ (22.9 m)
o For general reference only;
for longer duct runs, increase duct size and contact a qualified and trained installer.
o Straight runs and gradual
turns are best; for example, each 90° elbow is equivalent to 5’ – 10’ (1.52 – 3.05 cm) of straight run.
• 7” (17.8 cm) round duct for 300 – 600 CFM; 10” for 900 – 1500 CFM o Never use flexible duct; it
creates back pressure/air turbulence and greatly reduces performance.
GAS
Not applicable
ELECTRICAL
• Hardwire direct with two-wire ground
• 120 VAC/60 Hz
• Max. amp usage (rating includes recommended ventilator kit rating)—see Dimensions & Specifications table
PLUMBING
Not applicable
DTWS Slim Traditional
Wall Hood
DTWN Tall
Traditional Ledgeless
Wall Hood
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
VENTILATION
Designer Built-In Wall Hoods
Installation Requirements
* A 1,200 CFM interior- or exterior-power ventilator should be used when installed over range/rangetop with gas char-grill. ** It is recommended that the 1,500 CFM ventilator be used with longer duct runs.
Note: Maximum amp rating for hoods includes recommended ventilator kit rating. All products must be hard wired with two-wire ground. An interior- or exterior-power ventilator kit must be purchased for installation with all 18”H. hoods.
Model Ventilator Kits Duct Size Max. Amps
Interior Exterior Interior Exterior Interior Exterior
DTWS3049 DIV300/440 DEV900 7” (17.8 cm) 10” (25.4 cm) 1.7/3.2 6.6 DTWS3649 DIV300/440 DEV900 7” (17.8 cm) 10” (25.4 cm) 1.7/3.2 6.6 DTWS4249 DIV440 DEV900 7” (17.8 cm) 10” (25.4 cm) 3.2 6.6
DTWS4849 DIV880 DEV1200/1500** 10” (25.4 cm) 10” (25.4 cm) 5.6 4.3/5.1 DTWN3048 VIV300/600/1200* VEV900/1200* 7” (17.8 cm) 10” (25.4 cm) 2.4/4.6/6.6 6.6/3.9 DTWN3648 VIV300/600/1200* VEV900/1200* 7” (17.8 cm) 10” (25.4 cm) 2.4/4.6/6.6 6.6/3.9 DTWN4248 VIV600/1200* VEV900/1200* 7” (17.8 cm) 10” (25.4 cm) 4.6/6.6 6.6/3.9 DTWN4848 VIV1200* VEV1200/1500** 10” (25.4 cm) 10” (25.4 cm) 7.0 4.3/5.1
Note: All CFMs are based on tests with 0.1 static pressure. Without applying static pressure (some brands do not), CFM could be greatly overstated.
UTILITY REQUIREMENTS
Page 5
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
VENTILATION
Designer Built-In Wall Hoods
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
Ventilator Kits
• See Installation Requirements table for recommendations for each hood model
• A 1,200 CFM interior or 1,500 CFM exterior (if applicable) ventilator should be used over ranges/rangetops with gas grill
• Must use Viking ventilator kits with Viking hoods; use of non-Viking kits voids product warranty
Duct Covers
• DCW for DTWN models o 12”H./12”D. o Extend height of hood by 12”; conceal duct
• Stainless Steel (SS), Black (BK), White (WH), Biscuit (BT), Stone Gray (SG), and Graphite Gray (GG). o When ordering, specify finish code following accessory model number (for example, DCSB3008-SS)
Duct Cover Extensions
• For use with DTWS Slim Traditional Wall Hoods
• Extends height of hood by up to 12” (for 10’ ceilings)
• Replaces adjustable duct cover supplied with hood
• Stainless Steel (SS), Black (BK), White (WH), Biscuit (BT), Stone Gray (SG), and Graphite Gray (GG). o Specify finish code following accessory model number (for example, DCCE1010-SS)
Installation Notes & Accessories
Kit model Description Hood models Approx. ship wt. lbs. (kg)
DIV300 300 CFM interior power DTWS3049/3649 15 (6.8) DIV440 440 CFM interior power DTWS3049/3649/4249 25 (11.3) DIV880 880 CFM interior power DTWS4849 36 (16.2) DEV900 900 CFM exterior power DTWS3049/3649/4249 39 (17.6) DEV1200 1200 CFM exterior power DTWS3649/4249/4849 53 (23.9) DEV1500 1500 CFM exterior power DTWS4849 47 (21.3) VIV300 300 CFM interior power DTWN3048/3648 27 (12.2) VIV600 600 CFM interior power DTWN3048/3648/4248 27 (12.2) VIV1200 1200 CFM interior power DTWN3048/3648/4248/4848 43 (19.4) VEV900 900 CFM exterior power DTWN3048/3648/4248 39 (17.6) VEV1200 1200 CFM exterior power DTWN3048/3648/4248/4848 53 (23.9) VEV1500 1500 CFM exterior power DTWN4848 47 (21.3)
Model Description Approx. ship wt. lbs. (kg)
DCW30 Duct cover for 30”W. DTWN 10 (4.5) DCW36 Duct cover for 36”W. DTWN 11 (5.0) DCW42 Duct cover for 42”W. DTWN 13 (5.9) DCW48 Duct cover for 48”W. DTWN 14 (6.3)
Model Description Approx. ship wt. lbs. (kg)
DCCE1010 Duct cover extension (for 30”W. DTWS hood) 4 (1.8) DCCE1210 Duct cover extension (for 36” & 42”W. DTWS hoods) 6 (2.7) DCCE2010 Duct cover extension (for 48”W. DTWS hood) 9 (4.1)
Page 6
RELEASED 12/1/07
©2007 VRC—INFORMATION SUBJECT TO CHANGE
VENTILATION
Designer Built-In Wall Hoods
PLANNING AND DESIGN GUIDE
VIKINGRANGE.COM • 1-888-VIKING1
Backsplashes
• Stainless Steel (SS)
• 30”H.
• Backsplashes protect the wall space below hood
• Create a continuous finish between cooking surface and hood
• Low maintenance, easy to clean
• Hemmed edges with screw holes
• Kit includes backsplash and fastening screws
Warming Shelf Panels
• Stainless Steel (SS)
• 12”D./12”H.
• Shelf panels hold cookware and condiments
• Fold up/down, heavy-duty warming shelves (non-removable), factory installed on stainless steel backsplash
• 15-7/8”W. X 10-1/8”D.
• Kit includes shelf (or shelves) and fastening screws
Compliance Information
WARRANTY SUMMARY*
• One-year full warranty—complete product
• Five-year limited warranty—all ventilator motors
• Ninety-day limited warranty—cosmetic parts such as glass, painted, and decorative items
*Must use Viking ventilator kits with Viking hoods; use of non-Viking kits voids product warranty. For complete warranty see
Use & Care Guide.
Warranty valid on Viking products shipped within the United States and Canada.
Installation Notes & Accessories
Model Description Approx. ship wt. lbs. (kg)
BKS30 30”W. backsplash 7 (3.2) BKS36 36”W. backsplash 9 (4.1) BKS42 42”W. backsplash 12 (5.4) BKS48 48”W. backsplash 14 (6.3)
Model Description Approx. ship wt. lbs. (kg)
WGP30 30”W. warming shelf panels (one shelf) 9 (4.1) WGP36 36”W. warming shelf panels (two shelves) 12 (5.4) WGP42 42”W. warming shelf panels (two shelves) 14 (6.3) WGP48 48”W. warming shelf panels (two shelves) 16 (7.2)
Loading...