Viking DMOD Installation Manual
Sealing Surface
Waveguide Cover
Oven Cavity
DrawerMicro™ Oven
INSTALLATION INSTRUCTIONS
IMPORTANT - PLEASE READ AND FOLLOW
• INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
• THE INSTALLER SHOULD LEAVE THESE INSTRUCTIONS WITH THE CONSUMER WHO SHOULD RETAIN FOR LOCAL
INSPECTOR’S USE AND FOR FUTURE REFERENCE.
• FOR
SAFETY CONSIDERATIONS DO NOT INSTALL DRAWER IN ANY COMBUSTIBLE CABINETRY, WHICH IS NOT IN
ACCORD WITH THE STATED CLEARANCES AND DIMENSIONS ON PAGE 2, SEE FIGURE 1.
UNPACKING YOUR
DrawerMicro Oven
Remove all packing materials from inside the DrawerMicro
Oven. DO NOT REMOVE THE WAVEGUIDE COVER,
which is located on the top of the appliance.
Remove the feature sticker, if there is one. Check the
drawer for any damage, such as misaligned or bent drawer,
damaged drawer seals and sealing surfaces, broken or
loose drawer guides and dents inside the cavity or on
the front side of the drawer. If there is any damage, do
not operate the appliance and contact your dealer or a
VIKING AUTHORIZED SERVICER.
IMPORTANT NOTES TO THE
INSTALLER
• Read all of the Installation Manual before installing the
DrawerMicro Oven.
• Remove all packing material before connecting the
electrical supply.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
IMPORTANT NOTES TO THE
CONSUMER
Keep this manual with your Use and Care Manual for future
reference.
• As when using any microwave oven generating heat,
there are certain safety precautions you should follow.
These are listed in the Use and Care Manual. Read all
and follow carefully.
• Be sure your DrawerMicro Oven is installed and
grounded properly by a qualified installer or service
technician.
IMPORTANT SAFETY
INSTRUCTIONS
WARNING: If the information in this manual is not
followed exactly, a fire or electrical shock may result that
could cause property damage, personal injury or death.
WARNING: To reduce the risk of tipping, the DrawerMicro
Oven must be secured by a properly installed Anti-Tip
block.
• This appliance must be electrically grounded in
accordance with local codes.
• Make sure the wall coverings and the cabinets around
the DrawerMicro Oven can withstand the heat
generated by the appliance.
WARNING: Never leave children alone or unattended
in the area where a appliance is in use. Never leave the
drawer open when the microwave is unattended.
WARNING: Stepping, leaning or sitting on the drawer
may result in serious injuries and can also cause damage
to the appliance.
• Do not use the DrawerMicro Oven as a storage
space. This creates a potentially hazardous situation.
• Check that the time-of-day is in the display. If not, touch
Stop/Clear to prevent unintended use.
CLEARANCES AND DIMENSIONS
36"
countertop
height
24"
cabinet min.
22 56"
opening
14 5RQE"
opening
Allow
(RQE"
overlap
Allow ¾"
overlap.
Allow ¾"
overlap.
19" to top
of floor
4"
5"
Electrical outlet location
Anti-Tip
block
Floor must
support
100 lbs.
14 5RQE"
to bottom
of Anti-Tip
block
3 56O"
(6")
23 ½"
min depth
Allow RQE"
overlap
21 56:O"
23 6"
14 56:O"
1 6M"
door thickness
15 6"
23 (6"
15"
auto drawer
opening
1 36:O"
4 556QE"
• Dimensions that are shown in FIGURE 1 must be used.
Given dimensions provide minimum clearance. Locate
electrical outlet in the shaded area in the upper lefthand corner of the cutout. See FIGURE 4.
• Contact surface must be solid and level. Pay special
attention to the floor on which the appliance will sit.
The floor of the opening should be constructed of
plywood strong enough to support the weight of the
oven (about 100 pounds).
DrawerMicro Oven MEASUREMENTS
• Check location where the DrawerMicro Oven will be
installed for proper electrical supply.
• Your appliance can be built into a cabinet or wall by
itself or under a gas or electric wall oven.
• Be sure that the clearance of the floor between the
wall oven and the DrawerMicro Oven is a minimum of
2".
• The microwave interior will easily accommodate a 9"
x 13" oblong dish or a bag of microwave popcorn.
FIGURE 1
FIGURES 1 and 2 contain many DrawerMicro Oven measurements for
reference when planning the drawer’s location.
FIGURE 2
The DrawerMicro Oven can be installed below any electric
or gas wall Oven.
* Can also be installed using an electrical outlet in an
adjacent cabinet within the area where the provided
electrical cord can reach. Power cord access hole in
cabinet should be a minimum 1½" diameter hole and
deburred of all sharp edges.
IMPORTANT
electrical outlet to prevent tension.
DO NOT USE AN EXTENSION CORD.
Always check electrical codes for requirements.
Always allow sufficient power cord length to the
E2
ANTI-TIP BLOCK
Anti-tip
Block
6"
(153 mm)
4 Screws
PARTS SUPPLIED
4"
(101.6 mm)
5"
(127 mm)
Electrical Outlet
Location
Anti-tip
Block
6"
(153 mm)
Mounting
Flange
NORMAL INSTALLATION STEPS
ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS
To reduce the risk of tipping of the drawer, the Anti-Tip
block must be properly installed located 14 13/16" above
the floor on which the appliance will sit. The 6" Anti-Tip
block must be provided by the installer. See FIGURE 1.
The Anti-Tip block prevents serious injury that might result
from spilled hot liquids.
If the DrawerMicro Oven is ever moved to a different
location, the Anti-Tip block must also be moved and
installed. When installed to the wall, make sure that the
screws completely penetrate the dry wall and are secured
in wood or metal so that the block is totally stable. When
fastening, be sure that the screws do not penetrate
electrical wiring or plumbing.
ELECTRICAL OUTLET
The electrical requirements are a 120 volt 60 Hz, AC
only, 15 amp. or more protected electrical supply. It is
recommended that a separate circuit serving only this
appliance be provided.
The
appliance
It must be plugged into a wall receptacle that is properly
installed and grounded. Should you only have a 2-prong
outlet, have a qualified electrician install a correct wall
receptacle.
is equipped with a 3-prong grounding plug.
FIGURE 3
Note:
If you have any questions about the grounding or electrical
instructions, consult a qualified electrician or service
person.
DRAWER INSTALLATION
1. Place the
cabinet opening. Plug the power supply cord into the
electrical outlet.
2. Carefully guide the
opening. Avoid pinching the cord between the oven
and the wall.
3. Slide the drawer all the way until the mounting flange
is flush with the face of the cabinet. See FIGURE 5A.
4. Open the drawer. Using the 4 holes on the drawer as
a template, pre drill the cabinet using a 1/16" bit. See
FIGURE 5A.
5. Secure the drawer with the 4 screws supplied. See
FIGURE 5B.
DrawerMicro Oven
appliance
adjacent to the wall or
into the prepared
FIGURE 4
FIGURE 5A
FIGURE 5B
E3
GROUNDING INSTRUCTIONS
3-Prong Plug
Grounding Pin
3-Prong
Receptacle
Ground
Receptacle Box
PERMANENT AND CORRECT INSTALLATION
This appliance must be grounded. The DrawerMicro
Oven is equipped with a cord having a grounding wire
with a grounding plug. It must be plugged into a wall
receptacle that is properly installed and grounded in
accordance with the National Electrical Code and local
codes and ordinances. In the event of an electrical
short circuit, grounding reduces risk of electric shock by
providing an escape wire for the electric current.
W A R N I N G :
Improper use of
the grounding
plug can result in
a risk of electric
shock. Do not
use an extension
cord.
CARE, CLEANING AND
MAINTENANCE
Refer to the Use and Care Manual for cleaning
instructions.
MODEL AND SERIAL NUMBER
LOCATION
The name plate, including model and serial number, is
located on the faceplate behind the drawer front.
BEFORE YOU CALL FOR SERVICE
Read the BEFORE YOU CALL and operating instruction
sections in your Use and Care Manual. It may save you time
and expense. The list includes common occurrences that
are not the result of defective workmanship or materials
in this range.
Refer to the warranty in your Use and Care Manual for
Viking’s toll-free service number and address. Please
call or write if you have inquiries about your microwave
product and/or need to order parts.
VIKING RANGE CORPORATION
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
E4
TINSKB113MRR0
Loading...