Viking DGSU100, DGSU160 Installation Information

9

INITIAL IGNITION OF BURNERS

All cooktops are tested before leaving the factory. Field adjustments may be necessary for proper mixture of gas and
air for proper operation. When the cooktop is connected to gas and electrical service, it should be adjusted by a
qualified technician. If it is not, contact your dealer for the name of their authorized service agency in your area. Gas
conversions and initial installation adjustments are not the responsibility of the manufacturer.

FINAL PREPARATION

a) New units are cleaned atthe factory to remove any visible signs of dirt, oil, grease, etc. remaing from the

manufacturing process. Some stainless steel parts may have a plastic protective wrapper which must be peeled off.
The cooktop should be washed thoroughly with hot, soapy water and then rinsed and wiped dry to remove these
film residues and any installation dust or debris before being used for food preparation.

b) All stainless steel body parts should be wiped regularly with hot, soapy water and with a liquid cleanser designed

for this material if build-up occurs.

DDOO NNOOTT UUSSEE

steel wool, abrasive cloths, cleansers, or powders! If it is
necessary to scrape stainless steel to remove encrusted material, soak with hot, wet cloths to loosen the material,
then use a wood or nylon scraper.

DDOO NNOOTT UUSSEE

a metal knife, spatula, or any other metal tool to scrape stainless

steel! Scratches are almost impossible to remove.

REPLACEMENT PARTS

Only authorized replacement parts may be used in performing service on the cooktop. Replacement parts are available
from factory authorized parts distributors. Contact Viking Range Corporation- Preferred Service at [phone] for
the nearest parts distributor in your area.

DESCRIPTION DGSU100 30” W. mODEL DGSU160 36” W. MODEL

Cutout Width - Minimum 29 1/8” (74.0 cm) 34 7/8” (88.6 cm)

Maximum 29 7/8” (75.9 cm) 35 7/8” (91.1 cm)
Cutout Height - Minimum 3 1/8” (7.9 cm)
Cutout Depth - Minimum 19 3/4” (50.2 cm)

Maximum 20 1/8” (51.1cm)
Overall Width 30 3/4” (78.1 cm) 36 3/4” (93.3 cm)
Overall Height from Bottom 4 3/8” (13.7 cm)
Overall Depth from Rear 21” (53.3 cm)
Gas Requirements To field convert from natural to LP/Propane, the orifice spuds and regulator must be physically

changed. You will need to order accessory kit DLPK. Accepts standard residental 1/2” (1.3 cm)

I.D. gas service line.
Electrical Requirements 120 VAC/60 Hz; 4 ft. (121.9 cm), 3-wire cord with grounded 3-prong plug attached to product.
Maximum Amp Usage 2.0 amps
Surface Burner Rating Left Front- 14,000 Nat./13,500 LP (BTU) Left Front- 12,000 Nat./11,500 LP (BTU)

(4.1 Nat./4.0 LP [kw]) (3.5 Nat./2.8 LP [kw])

Left Rear- 12,000 Nat./11,500 LP (BTU Left Rear- 10,000 Nat./LP (BTU)

(3.5 Nat./2.8 LP [kw]) (2.9 Nat./LP [kw])

Right Rear- 8,000 Nat./LP (BTU) Center- 14,000 Nat./13,500 LP (BTU)

(2.1 Nat./LP [kw}) (4.1 Nat./4.0 LP [kw])

Right Front- 6,000 Nat./LP (BTU) Right Rear- 8,000 Nat./LP (BTU)

(1.8 Nat./LP [kw]) (2.1 Nat./LP [kw})

Right Front- 6,000 Nat./LP (BTU)

(1.8 Nat./LP [kw])
Approximate Shipping 49 lb. (22.0 kg.) 74 lb. (33.3 kg)
Weight

SPecifications

PROXIMITY TO SIDE CABINETS

1. The cooktop may be installed directly to existing base cabinets.

2. The cooktop CANNOT be installed directly adjacent to sidewalls, tall cabinets, tall appliances, or other side vertical
surfaces above 36” (91.4 cm) high. There must be a minimum of 8” (20.3 cm) side clearance from the cooktop to
such combustible surfaces above the 36” (91.4 cm) counter height.

3. Within the 8” (20.3 cm) side clearance to combustible vertical surfaces above 36” (91.4 cm), the maximum wall
cabinet depth must be 13” (33.0 cm) and wall cabinets within this 8” (20.3 cm) side clearance must be 18” (45.7 cm)
above the 36” (91.4 cm) high countertop.

4. Wall cabinet above the cooktop must be a minimum of 36” (91.4 cm) above the cooking surface for a full width of
the cooktop. This minimum height requirement does not

apply if a rangehood is installed over the cooking surface.

5. A 120 volt wall receptacle should be located approximately 6” (15.2 cm) below the countertop cutout and 12”

(30.5 cm) from the right side of the cutout.

MINIMUM CLEARANCES FROM ADJACENT COMBUSTIBLE
CONSTRUCTION

•Above countertop (above 36” [91.4 cm])

•Sides 8” (20.3 cm)

•Rear 2½” (6.4 cm)

•Within 8” (20.3 cm) side clearance. Wall cabinets no deeper
than 13” (33.0 cm)

•Must be minimum 18” (45.7 cm) above countertop

•Wall cabinets directly above the product must be minimum
36” (91.4 cm) above the countertop.

4

13” max.
(33.0 cm)

36” min.
(91.4 cm)

18” min.
(45.7 cm)

8” min.
(20.3 cm)

2 1/2” min.
(6.4 cm)

3 1/8”
(7.9 cm)

36” min.
(91.4 cm)