How it Works
Viking
Loading...
DCH 12''H
Installation Manual
22 pgs3.15 Mb0

Viking DCH 12''H, DCWH, DCIH, DTWS, DTWL Installation Manual

...
Viking Range Corporation
111 Front Street
Greenwood, Mississippi 38930 USA
(662) 455-1200
For product information,
call 1-888-VIKING1 (845-4641)
or visit the Viking Web site at
vikingrange.com
(062207J)
U
L
C
U
L
Viking Installation Guide
Designer Hoods
Table of Contents
Warnings & Important Information
_________________________________________________________ 3-
4
DCH 12”H. Classic Chimney Wall Hoods w/Standard Ventilator
Dimensions & Specifications ______________________________________________________ 5 Clearance Dimensions ____________________________________________________________ 6
Interior Ventilator Dimensions _____________________________________________________ 7 DCWH/DCWN/DCWL Classic Chimney Wall Hoods— Ledgeless & Ledge 30”, 33”, 36”, 39”, 42”, 45”, 48”, & 51”
Dimensions & Specifications_______________________________________________________ 8
Clearance Dimensions ____________________________________________________________ 9
Interior Ventilator Dimensions ____________________________________________________ 10
Exterior Ventilator Dimensions ___________________________________________________ 11 DCIH Classic Chimney Island Hoods 36”, 42”, & 54”
Dimensions & Specifications ______________________________________________________ 12
Clearance Dimensions___________________________________________________________ 13
Interior Ventilator Dimensions _____________________________________________________ 14
Exterior Ventilator Dimensions ___________________________________________________ 15 DTWS Slim Traditional Wall Hoods 30”, 36”, 42”, & 48”
Dimensions & Specifications _____________________________________________________ 16
Clearance Dimensions ___________________________________________________________ 17
Interior Ventilator Dimensions _____________________________________________________ 18
Exterior Ventilator Dimensions ___________________________________________________19 DTWL/DTWN Tall Traditional Wall Hoods—Ledgeless & Ledge 30”, 36”, 42”, & 48”
Dimensions & Specifications _____________________________________________________ 20
Clearance Dimensions___________________________________________________________ 21
Interior Ventilator Dimensions ___________________________________________________ 22
Exterior Ventilator Dimensions ___________________________________________________ 23 DSWB Box Wall Hoods 30”, 36”, 42”, & 48”
Dimensions ___________________________________________________________________ 24
Clearance Dimensions ____________________________________________________________25
Interior Ventilator Dimensions _____________________________________________________ 26
Exterior Ventilator Dimensions ___________________________________________________ 27 Planning Information________________________________________________________________ 28 Installation Procedure
Installation (DCH 12”H. Classic Chimney Wall Hoods w/Standard Ventilator) ___________ 29
Duct Cover Option (DCH 12”H. Classic Chimney Wall Hoods w/Standard Ventilator)____ 31
Installation (DCH 12”H. Classic Chimney Wall Hoods w/Recirculating Kit) ______________ 32
Installation (DCWH/DCWN/DCWL Classic Chimney &
DTWL/DTWN Tall Traditional Wall Hoods) ________________________________________ 34 Duct Cover Option (DCWH/DCWN/DCWL Classic Chimney Wall Hoods) ______________ 35 Duct Cover Option (DTWL/DTWN Tall Traditional Wall Hoods) _______________________ 36 Installation (DTWS Slim Traditional & DSWB Box Wall Hoods) ________________________ 36 Duct Cover Option (DTWS Slim Traditional Wall Hoods) _____________________________ 38 Duct Cover Required (DSWB Box Wall Hoods) _____________________________________39 Installation (DCIH Classic Chimney Island Hoods) ___________________________________ 40
Wiring Diagram _____________________________________________________________________42 Service & Registration_______________________________________________________________ 43
3
IMPORTANT–Please Read and Follow!
NOTE:
If installing hood with warming shelf panel,
install warming shelf panel first.
IMPORTANT – PLEASEREAD AND FOLLOW
• Before beginning, please read these instructions completely and carefully.
• Do not remove permanently affixed labels, warnings, or plates from the product. This may void the warranty.
• Please observe all local and national codes and ordinances. If no local codes are applicable, wire in accordance with the National Electrical Code, ANSI/NFPA 70-latest edition.
• Outdoor approved models should be installed in a covered non-enclosed area and should be protected from the elements as much as possible.
• The installer should leave these instructions with the consumer who should retain for local inspector’s use and for future reference.
• Check with a qualified and trained installer orlocal codes for makeup air requirement, if any.
This hood is for residential installation only and isnot designed for installation over a commercial product. Make sure power is off at the main circuit breaker or fuse box before making connections. To avoid risk of fire, electric shock, or injury to persons, turn offthe electricityto the hood from the power supply before servicing or cleaning.
Viking hoods are equipped with the variable speed controls for blowers. These units will not function witha single speed ventilator. All Viking ventilatorkits are designed specifically for use with Viking hoods.Use ofany non-Viking ventilator kit will void the hoodwarranty.
READ AND SAVE THESEINSTRUCTIONS
W A R N I N G
TO REDUCE THE RISK OF A RANGETOP GREASE FIRE
1. Never leave surface units unattended at high setting. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowlyon low or medium settings.
2. Always turn hood ON when cookingat high heat or when cooking flaming foods. (i.e.crepes suzette, cherries jubilee, peppercorn beef flambé).
3. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fanor filter.
4. Use proper pan size. Always use cookware appropriate for the size of the surface element.
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING
1. Installation work and electrical wiring must be done by qualified person(s) in accordance with all applicable codes and standards, including fire-rated construction.
2. Sufficient air is needed for proper combustion and exhausting of gases through the flute (chimney) of fuel burning equipmentto prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the NationalFire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
3. When cutting or drilling into wall or ceiling,do not damage electrical wiring or other hidden utilities.
4. Ducted fans must always be vented to the outdoors.
5. WARNING!: To reduce risk of fire, use only metal ductwork.
6. CAUTION!: To reduce risk of fire and to properly exhaust air, be sure to duct air outside. Do not vent exhaust air into spaceswithin walls or ceilings, or into attics, crawl spaces,or garages.
7. CAUTION!: To Reduce the Riskof Fire and Electric Shock, Install this rangehood only with remote blower models manufactured by Viking, model numbers – DEV900/DEV1200, VEV900/VEV1200, OR DEV1500, VEV1500 or integral blowers manufactured by Viking, model numbers – DIV300, DIV440, DIV600, DIV800, DIV1200, VIV300, VIV600, or VIV1200. NOTE – Please refer inside for specific canopy/blower combinations.
W A R N I N G
W A R N I N G
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING
• Use this unit only in themanner intendedby the manufacturer. If you have any questions, contact the manufacturer.
• Before servicing or cleaning unit, switch power off at service panel and lock service panelto prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
5
IMPORTANT–Please Read and Follow!
4
W A R N I N G
TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS
Rangehoods must be installed with the ventilators that are specified on their carton indicating suitability with this model. Other ventilators cannot be substituted.
C A U T I O N
For general ventilating use only. Do not useto exhaust hazardous or explosive materials and vapors.
W A R N I N G
TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGETOP GREASE FIRE, OBSERVE THE FOLLOWING. (Based on “Kitchen Firesafety Tips,” published by NFPA.)
1. SMOTHER FLAMES with a close fitted lid, cookie sheet, or metal tray, then turnoff theburner. BE CAREFUL TO PREVENT BURNS. If the flamesdo not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
2. NEVER PICK UP A FLAMING PAN. You may be burned.
3. DO NOT USE WATER, including wet dishclothsor towels a violent steam explosion will result.
4. Use an extinguisher ONLY if
• You know it is a Class ABCextinguisher, and you
already know how to operate it.
• The fire is small and contained in thearea where
it started.
• The fire department is being called.
• You can fight the fire with your back toan exit.
DCH 12”H. Classic Chimney Wall Hoods w/Standard Ventilator
Description 30” 36”
Duct cover width 16” (40.6 cm) Duct cover depth 12” (30.5 cm) Duct cover height 18” (45.7 cm) to 30” (76.2 cm) Number of lights 2 Number of filters 2 Interior ventilator kit 460 CFM Interior duct size* 7” (17.8 cm) Interior—Maximum amps 5.6
* Disregard when using recirculating kits. 460 CFM bloweris shipped with hood.
NOTE: All products must be hard wired with 2-wire with ground.
2
4
”
(
61
.
0
c
m)
1
6”
(
4
0
.6
cm
)
1
2
”
(
30
.
5
c
m)
1
8
”
(
30
.
5
c
m)
t
o
3
0
”
(
76
.
2
c
m)
1
2
”
(
30
.
5
c
m
)
A
A (Hood width)
30”W. 29-7/8” (75.9 cm) 36”W. 35-7/8” (91.1 cm)
2 ”
(
5. 1
cm)
Dimensions & Specifications
(DCH 12”H. Classic Chimney Wall Hoods w/Standard Ventilator)
NOTE: Optional duct cover sold separately.
6
Clearance Dimensions
7
3
0
”
min.
(7
6. 2
c
m)
t
o
33
”
ma
x
.
(8
3. 8
c
m)
66
”mi
n.
(1
6
7
.6
cm
)
t
o
69”m
ax.
(1
7
5
.3
cm
)
36”
(91
.
4
c
m)
A
30”W. 14-15/16” (37.9 cm) 36”W. 17-15/16” (45.6 cm)
16” (40.6 cm)
A
4”
(10.2 cm)
120 V
7” (17.8 cm) dia. duct location
9-3/4”
(24.8 cm)
460 CFM Interior Ventilator Installation
(DCH 12”H. Classic Chimney Wall Hoods w/Standard Ventilator)
(DCH 12”H. Classic Chimney Wall Hoods w/Standard Ventilator)
Top view
Interior Ventilator Dimensions
Clearance Dimensions
9
Dimensions & Specifications
8
24
”
(
6
1
.
0
c
m)
B
C
A
D
1
2
”
(
3
0
.
5
c
m)
E
E (Hood height)
30”W. 12” (30.5 cm) 33“W. 12” (30.5 cm) 36”W. 14” (35.6 cm) 39“W. 14” (35.6 cm) 42”W. 14” (35.6 cm) 45“W. 14” (35.6 cm) 48”W. 14” (35.6 cm) 51”W. 14” (35.6 cm)
A (Duct cover width)
30”W. 10” (25.4 cm) 33“W. 10” (25.4 cm) 36”W. 12” (30.5 cm) 39“W. 12” (30.5 cm) 42”W. 12” (30.5 cm) 45“W. 12” (30.5 cm) 48”W. 18” (45.7 cm) 51”W. 18” (45.7 cm)
B (Hood width)
30”W. 29-7/8” (75.9 cm) 36”W. 35-7/8” (91.1 cm) 42”W. 41-7/8” (106.4 cm) 48”W. 47-7/8” (121.6 cm)
D (Duct height)
30”/33“W.
36”/39“W. 42”/45“W. 48”/51“W.
18” (45.7 cm) to
30“ (76.2 cm)
16” (40.6 cm) to
28” (71.1 cm)
C (Hood width–Ledge models)
33”W. 32-7/8” (83.5 cm) 39”W. 38-7/8” (98.4 cm) 45”W. 44-7/8” (114.0 cm) 51”W. 50-7/8” (129.2 cm)
2
5-
1
/
2
”
(
6
4
.
8
c
m)
Led
ge
mod
e
ls
on
l
y
2”
(5
.
1
c
m)
(DCWH Classic Chimney Wall Hoods 30”, 36”, 42”, & 48”) (DCWN Ledgeless models 30”, 36”, 42”, & 48”) (DCWL Ledge models 33”, 39”, 45”, & 51”)
* A 1,200CFM interior-or exterior-powerventilator should be used when installed over range/rangetop with gas char-grill. Max duct run is50 ft. ** It isrecommended that the 1,500 CFMventilator be used with longer duct runs. Max duct runis 75 ft.
NOTE: Maximum amp rating for hoods includes recommended ventilator kit rating; All products must be hard wired with 2-wire with ground. An interior- or exterior-power ventilator kit must be purchased for installation with all Designer hoods.
DCWH/DCWN/DCWL Classic Chimney Wall Hoods—Ledgeless & Ledge
Description 30”/33” 36”/39” 42”/45” 48”/51”
Duct cover width 10” (25.4 cm) 12” (30.5 cm) 12” (30.5 cm) 18” (45.7 cm) Duct cover depth 12” (30.5 cm) Duct cover height 18” (45.7 cm) to 16” (40.6 cm) to 16” (40.6 cm) to 16” (40.6 cm) to
30” (76.2 cm) 28” (71.1 cm) 28” (71.1 cm) 28” (71.1 cm)
Number of lights 2223 Number of filters 2233 Interior ventilator kits DIV300/ DIV300/ DIV600 DIV1200*
DIV440 DIV600
Exterior ventilator kits DEV900/ DEV900/ DEV900/ DEV1200*/
DEV1200* DEV1200* DEV1200* DEV1500**
Interior duct size 7” (17.8 cm) 7” (17.8 cm) 7” (17.8 cm) 10” (25.4 cm) Exterior duct size 10” (25.4 cm) Interior—Maximum amps 1.7/3.2 1.7/3.9 3.9 7.3 Exterior—Maximum amps 6.6./3.9 6.6./3.9 6.6/3.9 4.3/5.1
3
0
”
m
in
.
(
7
6. 2
cm
)
t
o
36
”
m
a
x.
(
9
1. 4
cm
)
6
6
”mi
n.
(16
7.6 c
m)
t
o
7
2
”m
ax.
(18
2.9 c
m)
3
6”
(
91
.
4
c
m)
(DCWH/DCWN/DCWL Classic Chimney Wall Hoods)
NOTE: For best performance, it is recommended that the bottom of the hood be 30” (76.2 cm) to 36” (91.4 cm) above the countertop. These dimensions provide for safe and efficient operation of the hood.
10
Exterior Ventilator Dimensions
11
1-1/2”
(3.8 cm)
10” (25.4 cm) dia.
duct location
1-1/2”
(3.8 cm)
18”
(45.8 cm)
23-15/16”
(60.8 cm)
1-1/2”
(3.8 cm)
120 V power supply
6”
(15.2 cm)
Classic Chimney w/Ledge
Classic Chimney
1-1/2”
(3.8 cm)
7” (17.8 cm) dia.
duct location
A
1-1/2”
(3.8 cm)
120V power supply
6”
(15.2 cm)
B
A
30”W. 10” (25.4 cm) 33“W. 10” (25.4 cm) 36“W. 12” (30.5 cm) 39“W. 12” (30.5 cm) 42“W. 12” (30.5 cm) 45“W. 12” (30.5 cm)
B
30”W. 14-15/16” (37.9 cm) 33“W. 14-15/16” (37.9 cm) 36“W. 17-15/16” (45.6 cm) 39“W. 17-15/16” (45.6 cm) 42”W. 20-15/16” (53.2 cm) 45“W. 20-15/16” (53.2 cm)
Classic Chimney w/Ledge
Classic Chimney
1-1/2”
(3.8 cm)
1-1/2”
(3.8 cm)
1-1/2”
(3.8 cm)
18”
(45.8 cm)
1-1/2”
(3.8 cm)
120 V power supply
Classic Chimney w/Ledge
Classic Chimney
6”
(15.2 cm)
10” (25.4 cm) dia. duct location
23-15/16”
(60.8 cm)
1-1/2”
(3.8 cm)
1-1/2”
(3.8 cm)
A
1-1/2”
(3.8 cm)
120V power supply
Classic Chimney w/Ledge
Classic Chimney
6”
(15.2 cm)
C
B
A
30”W. 10” (25.4 cm) 33“W. 1 0” (25.4 cm) 36“W. 12” (30.5 cm) 39”W. 12” (30.5 cm) 42”W. 12” (30.5 cm) 45”W. 12” (30.5 cm)
B
30”W. 14-15/16” (37.9 cm) 33“W. 14-15/16” (37.9 cm) 36”W. 17-15/16” (45.6 cm) 39“W. 17-15/16” (45.6 cm) 42“W. 20-15/16” (53.2 cm) 45“W. 20-15/16” (53.2 cm)
C (Duct diameter)
30”W. 8” (20.3 cm)* 33“W. 8” (20.3 cm)* 36“W. 10” (25.4 cm) 39“W. 10” (25.4 cm) 42“W. 10” (25.4 cm) 45“W. 10” (25.4 cm)
900 or 1200 CFM Exterior Ventilator Installation
for 30”, 33”, 36”, 39”, 42”, & 45” models
1200 or 1500 CFM Exterior Ventilator Installation
for 48” & 51” models
300, 440 or 600 CFM Interior Ventilator Installation
for 30”, 33”, 36”, 39”, 42”, & 45” models
(DCWH/DCWN/DCWL Classic Chimney Wall Hoods) (DCWH/DCWN/DCWL Classic Chimney Wall Hoods)
1200 CFM Interior Ventilator Installation
for 48” & 51” models
Top view
Top view
Top view
Top view
Interior Ventilator Dimensions
* 8” to 10” transition to be acquired locally.
Clearance Dimensions
13
Dimensions & Specifications
12
3
0
”
(76
.
2
c
m)
B
A
1
4
”
(35
.
6
c
m)
C
2”
(
5. 1
cm
)
1
2
”
(3
0
.
5
c
m)
B (Hood width)
36”W. 35-7/8” (91.1 cm) 42”W. 41-7/8” (106.4 cm) 54”W. 53-7/8” (136.8 cm)
A (Duct cover width)
36”W. 12” (30.5 cm) 42”W. 12” (30.5 cm) 54”W. 18” (45.7 cm)
C (Duct height)
36”W.
42”W.
54”W.
16” (40.6 cm)
or
28” (71.1 cm)
or
40” (101.6 cm)
(DCIH Classic Chimney Island Hoods 36”, 42”, & 54”)
* A 1,200CFM interior-or exterior-powerventilator should be used when installed over range/rangetop with gas char-grill. Max duct run is50 ft. ** It isrecommended that the 1,500 CFMventilator be used with longer duct runs. Max duct runis 75 ft.
NOTE: Maximum amp rating for hoods includes recommended ventilator kit rating; All products must be hard wired with 2-wire with ground. An interior- or exterior-power ventilator kit must be purchased for installation with all Designer hoods.
DCIH Classic Chimney Island Hoods
Description 36” 42” 54”
Duct cover width 12” (30.5 cm) 12” (30.5 cm) 18” (45.7 cm) Duct cover depth 12” (30.5 cm) Duct cover height 16” (40.6 cm) or 28” (71.1 cm) or 40” (101.6 cm) Number of lights 446 Number of filters 233 Interior ventilator kits DIV600 DIV600 DIV1200* Exterior ventilator kits DEV900/ DEV900/ DEV1200*/
DEV1200* DEV1200*/DEV1500** DEV1200*/DEV1500**
Interior duct size 7” (17.8 cm) 7” (17.8 cm) 10” (25.4 cm) Exterior duct size 10” (25.4 cm) Interior—Maximum amps 3.9 4.7 8.6 Exterior—Maximum amps 6.6./3.9 7.4/4.7/5.5 5.6/6.4
3
0
”
min
.
(
7
6
.
2
c
m
)
t
o
3
6
”
max
.
(
9
1
.
4
c
m
)
66”m
in.
(16
7.6
cm)
to
72”m
a
x
.
(18
2.9
cm)
36
”
(
91
.
4
cm)
NOTE: Optional duct cover sold separately.
(DCIH Classic Chimney Island Hoods)
NOTE: For best performance, it is recommended that the bottom of the hood be 30” (76.2 cm) to 36” (91.4 cm) above the countertop. These dimensions provide for safe and efficient operation of the hood.
Loading...
+ 15 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use