Viking C-2000A, C-3000, C-4000, K-1900-3, K-1900-5 User Manual

The K-1705 Series entry phones provide a tough and
attractive handsfree phone for apartment, and resi­dential door entry or applications requiring a vandal
resistant speaker phone. The K-1705 Series entry
phones are available in two attractive finishes:
“brushed stainless steel” and “oil rubbed bronze”.

When the “Call” button is pressed, the K-1705-3
returns dial tone. The keypad may then be used to
dial any number. If no Touch Tone is entered within 8
seconds, CPC is detected, a busy signal is detected,
or the programmable maximum call time has elapsed,
the K-1705-3 will automatically disconnect. Alternatively, the K-1705-3 may be disconnected by pressing the “Call” button
again. The K-1705-3 comes complete with a standard, flush mount, rough-in box. In addition, an optional VE-6x7 weather
resistant, surface mount box is available.

For outdoor or harsh environments, the K-1705-3 is available with Enhanced Weather Protection (EWP). EWP products fea­ture rubber gaskets and boots, closed cell foam gasketing, hand soldered silicon sealed connections, anti-corrosive gel filled
butt connectors, as well as urethane encapsulated circuit boards with internally sealed, field-adjustable trim POTS and DIP
switches.

• Built-in high resolution color video camera with wide viewing,
tilt/swivel adjustments and wide operating temperature of

-30°F to 150°F

• Audio and video transmission on one CAT5E cable (page 5)

• Vandal Resistant Features: 14 gauge louvered stainless
steel faceplate with stainless steel speaker/mic screen, heavy
duty metal keypad and “Call” button, impact and scratch
resistant camera lens and hex drive mounting screws

• Weather Resistant Features: Mylar speaker, faceplate
gasket, mic and speaker gasket, internally sealed (IP67)
push button switch and keypad, sealed camera lens, potted
camera circuit board, stainless steel phone and camera
mounting hardware

• Available in 2 standard faceplate finishes: brushed stainless
steel or oil rubbed bronze

• Optional Enhanced Weather Protection (EWP), conforms to
NEMA requirements

• Yellow “in use” LED

• Telephone line powered

• Volume adjustments for microphone and speaker

• Advanced call progress detection: disconnects on busy
signal, return to dial tone, CPC, reorder tone, maximum call
time out and 40 second silence time out

• Selectable auto-answer feature for monitoring

• Selectable push button disconnect

• Zinc plated steel rough-in box with (2) 3/4” conduit knockouts

• Optional VE-6x7 Surface Mount Box available

• Microphone and speaker volume controls

• Selectable VOX switching speed

K-1705 Series

K-1705 Series

Video Entry Phones

with Keypads

May 16, 2008

PPrraaccttiicce

e

T

T

EELLEECCOOM

M

S

S

OOLLUUTTIIOONNSSFFOORRTTHHE

E

221

1

SST

T

C

C

EENNTTUURRY

Y

TECHNICAL

TECHNICAL

FFeeaattuurrees

s

PPhhoonnee......771155..338866..8888661

1

Dimensions: Overall: 140mm x 165mm x 66mm (5.5” x 6.5” x

2.6”) , Rough-in box: 114mm x 140mm x 64mm (4.5” x 5.5” x 2.5”)

Shipping Weight: 1.6 kg (3.5 lbs)
Operating Temperature: -34°C to 65°C (-30°F to 150°F)
Connections: Standard model: (3) gel-filled butt connectors (3M

Scotchlok UR2) and 2-position terminal block, EWP model: (5)
gel-filled butt connectors (3M Scotchlok UR2)

(See page 2 for complete specifications)

SSppeecciiffiiccaattiioonns

s

AApppplliiccaattiioonns

s

• Apartment entry phone when used with the K-1900-3
Apartment Entry Dialer or C-4000 Apartment/Office Entry

Controller or C-3000 Apartment Entry Controller

• Residential gate or door entry phone when used with the

C-2000A Door Entry Controller

• Courtesy and customer assistance phone

• Automated teller (ATM) phone

• Security or emergency phone

• Hot-Line phone when used with the K-1900-5 Hot-Line

Dialer

Note: When installing a line powered phone on a low
voltage and/or low loop current phone system extension, a TBB-1A
Talk Battery Booster may be required (Fax Back # 630).

• Kiosk phone with (100 number speed dialing) when used
with the K-1900-9 Multi-Number Dialer

Vandal Resistant Handsfree Entry

Phones with Built-In Keypad

K-1705-3 “Brushed Stainless Steel”

(similar to brushed nickel)

K-1705-3-BN “Oil Rubbed Bronze”

(satin dark brown powder paint

with fine copper metallic)

IF YOU HAVE A PROBLEM WITH A VIKING PRODUCT, PLEASE CONTACT: VIKING TECHNICAL SUPPORT AT [phone]

Our Technical Support Department is available for assistance Monday 8am - 4pm and Tuesday through Friday 8am - 5pm central time. So that we can give you better service, before you call please:

1. Know the model number, the serial number and what software version you have (see serial label).

2. Have your Technical Practice in front of you.

3. It is best if you are on site.

RETURNING PRODUCT FOR EXCHANGE

The following procedure is for equipment that has failed out-of-box (within 10 days of purchase):

1. Customer must contact Viking’s Technical Support at 715-386-8666 to determine possible causes for the problem. The

customer MUST be able to step through recommended tests for diagnosis.

2. If the Technical Support Product Specialist determines that the equipment is defective based on the customer's input
and troubleshooting, a Return Authorization (R.A.) number will be issued. This number is valid for fourteen (14)
calendar days from the date of issue.

3. After obtaining the R.A. number, return the approved equipment to your distributor, referencing the R.A. number. Your
distributor will then replace the product over the counter at no charge. The distributor will then return the product to
Viking using the same R.A. number.

4. The distributor will NOT exchange this product without first obtaining the R.A. number from you. If you haven't
followed the steps listed in 1, 2 and 3, be aware that you will have to pay a restocking charge.

RETURNING PRODUCT FOR REPAIR

The following procedure is for equipment that needs repair:

1. Customer must contact Viking's Technical Support Department at 715-386-8666 to obtain a Return Authorization (RA)

number. The customer MUST have a complete description of the problem, with all pertinent information regarding the
defect, such as options set, conditions, symptoms, methods to duplicate problem, frequency of failure, etc.

2. Packing: Return equipment in original box or in proper packing so that damage will not occur while in transit. Static
sensitive equipment such as a circuit board should be in an anti-static bag, sandwiched between foam and individual­ly boxed. All equipment should be wrapped to avoid packing material lodging in or sticking to the equipment. Include
ALL parts of the equipment. C.O.D. or freight collect shipments cannot be accepted. Ship cartons prepaid to:

Viking Electronics, 1531 Industrial Street, Hudson, WI 54016

3. Return shipping address: Be sure to include your return shipping address inside the box. We cannot ship to a PO Box.

4. RA number on carton: In large printing, write the R.A. number on the outside of each carton being returned.

the necessary modifications to maintain uninterrupted service.
If trouble is experienced with the K-1705-3, for repair or warranty information, please contact:

Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI 54016 [phone]

If the equipment is causing harm to the telephone network, the telephone company may request that you disconnect the
equipment until the problem is resolved.

Connection to Party Line Service is subject to State Tariffs. Contact the state public utility commission, public service com­mission or corporation commission for information.

WHEN PROGRAMMING EMERGENCY NUMBERS AND (OR) MAKING TEST CALLS TO EMERGENCY NUMBERS:

Remain on the line and briefly explain to the dispatcher the reason for the call. Perform such activities in the off-peak
hours, such as early morning or late evenings.

It is recommended that the customer install an AC surge arrester in the AC outlet to which this device is connected. This
is to avoid damaging the equipment caused by local lightning strikes and other electrical surges.

PART 15 LIMITATIONS

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communica­tions. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will
be required to correct the interference at his own expense.

FCC REQUIREMENTS

This equipment complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. Inside the front panel
of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX.
If requested, this number must be provided to the telephone company.

The REN is used to determine the number of devices that may be connected to a telephone line. Excessive REN's on a
telephone line may result in the devices not ringing in response to an incoming call. In most but not all areas, the sum of
the REN's should not exceed five (5.0) To be certain of the number of devices that may be connected to a line, as deter­mined by the total REN's, contact the local telephone company. For products approved after July 23, 2001, the REN for
this product is part of the product identifier that has the format US:AAAEQ##TXXXX. The digits represented by ## are the
REN without a decimal point (e.g., 03 is a REN of 0.3). For earlier products, the REN is separately shown on the label.

The plug used to connect this equipment to the premises wiring and telephone network must comply with the applicable
FCC Part 68 rules and requirements adopted by the ACTA. If your home has specially wired alarm equipment connected
to the telephone line, ensure the installation of this K-1705-3 does not disable your alarm equipment. If you have ques­tions about what will disable alarm equipment, consult your telephone company or a qualified installer.

If the K-1705-3 causes harm to the telephone network, the telephone company will notify you in advance that temporary
discontinuance of service may be required. But if advance notice isn't practical, the telephone company will notify the cus­tomer as soon as possible. Also, you will be advised of your right to file a complaint with the FCC if you believe it is nec­essary.

The telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the
operation of the equipment. If this happens, the telephone company will provide advance notice in order for you to make

LIMITED WARRANTY

Viking warrants its products to be free from defects in the workmanship or materials, under normal use and service, for a period of one year from the date of purchase from any authorized Viking distributor or 18 months from the date manu­factured, which ever is greater. If at any time during the warranty period, the product is deemed defective or malfunctions, return the product to Viking Electronics, Inc., 1531 Industrial Street, Hudson, WI., 54016. Customer must contact Viking's
Technical Support Department at 715-386-8666 to obtain a Return Authorization (R.A.) number.

This warranty does not cover any damage to the product due to lightning, over voltage, under voltage, accident, misuse, abuse, negligence or any damage caused by use of the product by the purchaser or others.

NO OTHER WARRANTIES. VIKING MAKES NO WARRANTIES RELATING TO ITS PRODUCTS OTHER THAN AS DESCRIBED ABOVE AND DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTIES OR MERCHANTABILITY OR FIT-

NESS FOR ANY PARTICULAR PURPOSE.

EXCLUSION OF CONSEQUENTIAL DAMAGES. VIKING SHALL NOT, UNDER ANY CIRCUMSTANCES, BE LIABLE TO PURCHASER, OR ANY OTHER PARTY, FOR CONSEQUENTIAL, INCIDENTAL, SPECIAL OR EXEMPLARY DAM­AGES ARISING OUT OF OR RELATED TO THE SALE OR USE OF THE PRODUCT SOLD HEREUNDER.

EXCLUSIVE REMEDY AND LIMITATION OF LIABILITY

. WHETHER IN AN ACTION BASED ON CONTRACT, TORT (INCLUDING NEGLIGENCE OR STRICT LIABILITY) OR ANY OTHER LEGAL THEORY, ANY LIABILITY OF VIKING SHALL

BE LIMITED TO REPAIR OR REPLACEMENT OF THE PRODUCT, OR AT VIKING'S OPTION, REFUND OF THE PURCHASE PRICE AS THE EXCLUSIVE REMEDY AND ANY LIABILITY OF VIKING SHALL BE SO LIMITED.

IT IS EXPRESSLY UNDERSTOOD AND AGREED THAT EACH AND EVERY PROVISION OF THIS AGREEMENT WHICH PROVIDES FOR DISCLAIMER OF WARRANTIES, EXCLUSION OF CONSEQUENTIAL DAMAGES, AND EXCLU­SIVE REMEDY AND LIMITATION OF LIABILITY, ARE SEVERABLE FROM ANY OTHER PROVISION AND EACH PROVISION IS A SEPARABLE AND INDEPENDENT ELEMENT OF RISK ALLOCATION AND IS INTENDED TO BE ENFORCED
AS SUCH.

Camera Specifications

Power: 5-9V DC regulated 150mA (6V DC adapter included)
Image Sensor: 1/4” color CMOS
Video Output: 1 VP-P composite, NTSC, 75 ohms
Resolution: 420 lines (640 x 480 @ 30fps / 307,200 pixels)
Sensitivity: 0.26 LUX (20 IRE) F 2.0
Lens: 3.4mm, pinhole 70° FOV (Field of View)
Tilt/Swivel Adjustment: Vertical +/- 20°, horizontal +/- 30° (see Diagram A)
Maximum Wire Run Length: 1000 ft with *RG59/RG6 for video and CAT5

for power (doubled pairs) and entry phone audio. 150 ft with CAT5E for video,
power and entry phone audio (longer video runs are possible by using video
balun transceivers, see Installation section F, page 5).

SSppeecciiffiiccaattiioonns

s

Entry Phone Specifications

Power: Telephone line powered 20V DC/20mA minimum
Dimensions: Overall: 140mm x 165mm x 66mm (5.5” x 6.5” x

2.6”) , Rough-in box: 114mm x 140mm x 64mm (4.5” x 5.5” x 2.5”)

Shipping Weight: 1.6 kg (3.5 lbs)
Speaker Volume: Approximately 70 db maximum @1m
Ring Voltage: 25V AC RMS minimum (for auto answer)
CPC Disconnect Time: 500ms minimum
REN #: 0.5 A

Entry Phone / Camera Specifications

Operating Temperature: -34° C to 65° C (-30° F to 150° F)
Humidity: Standard model: 5% to 95% non-condensing, EWP

model: Up to 100%
Connections: Standard model: (3) gel-filled butt connectors (3M
Scotchlok UR2) and 2-position terminal block, EWP model: (5) gel­filled butt connectors (3M Scotchlok UR2)

Recommended Surface Mount Box: Viking model VE-6x7 (Fax
Back Document 424)

2

* Note: RG59 or RG6 with solid center conductor and 95% bare copper braid shield.

Rotate
Left 30°

Diagram A

Camera Field of View:

70° Lens FOV

Rotate
Right 30°

Camera Lens

(1) .74”

diameter

Rear View of Optional

VE-6x7 (not included)

3.0” 3.3”

3.0”

Front View of Optional

VE-6x7 (not included)

2.25”

Condensation

Drain Hole

5.64”

6.72”

3.25”

(2) 0.2 x 0.43 slots

(4) 0.38” diameter

K-1705-3 shown with

VE-GNP Gooseneck

Pedestal (not included)

4.5”

2.5”

3/4” Conduit
Knockouts

Adhere gasket to front panel,
centering over mounting holes

5.5”

Condensation

Drain Hole

Rough-In Box*

(included)

1

2

ABC

3

DEF

4

GHI

5

JKL

6

MNO

7

PRS

8

TUV

9

W

XY

0

OPER

#

Call

VIKING

©

12

A

B

C

3

D

E

F

4

G

H

I

5

J

K

L

6

M

N

O

7

P

R

S

8

T

U

V

9

W

X

Y

0

O

P

E

R

#

Press "Call"button

then enter tenant code

Optional Instruction Label (included) - Clean

surface and adhere label when using a K-1705-3
with a K-1900-3 Apartment Entry Dialer.

(4) 6-32 X 3/4” Stainless steel, flat
head, hexdrive, screws (included)

IInnssttaallllaattiioon

n

The optional VE-6x7 Surface
Mount Box is designed to be sur­face mounted to a single gang
box, double gang box or VE-
GNP gooseneck pedestal (right).
For more information on the VE-

6x7 or the VE-GNP, retrieve Fax
Back Document 424.

A. Mounting

FFeeaattuurreessOOvveerrvviieew

w

3

* Note: Recommended
mounting height to bottom
of rough-in box is 50-54”.

Mounting Screws: 6-32 x 0.75" long
flathead with 5/64" hexdrive, 18-8 stainless
steel to prevent corrosion.

Faceplate: 14 guage 304 stainless steel.

Color Video Camera: Wide operating

temperature range of -30°F to 150°F, NTSC
composite video output with 420 lines of
resolution, 70° wide viewing angle lens, tilt and
swivel adjustments for aiming towards visitors.

Protective Camera Window: Impact resistant
polycarbonate lens with scratch resistant
coating and water-tight gasket.

Condensation Drain Hole

Faceplate Gasket: 1/8" thick closed cell PVC

to provide a water-tight seal.

VIKING

12

ABC3DEF

4

GHI5JKL6MNO

7

PRS8TUV9WXY

0

OPER

©

#

Call

Model:

Serial No:

XXXXXXXX

K-1705-3

Complies with FCC Part 15 and 68 Reg. No: AH3USA-32531-TE-E

P/N: DEV:

261102-1

REN: 1.0B

Viking Electronics, Inc. [phone]

VIKING

1531 Industrial St., Hudson, WI 54016

Keypad: Metal construction with internal seal

to provide vandal and weather resistance.

Microphone: Omni-directional microphone
with protective water-resistant cloth.

Speaker: Mylar speaker with rubber gasket to
maintain water-tight seal and eliminate water
deterioration.

Speaker Screen: Stainless steel speaker
screen with 0.018" diameter holes to prevent
punctures from paperclips, etc.

LED: Lights yellow for "In-Use" indication.

Push Button Switch: Push to initiate call,

push again to disconnect. Solid 304 stainless
steel internally sealed per IP67.

RoHS

Speaker Volume

Microphone Volume

DIP Switches (see page 6)

Earth Ground: To increase surge protection,

loosen the screw labeled (as shown) and
fasten a wire with spade terminal (included)
from the mounting screw to Earth Ground
(grounding rod, water pipe, etc.)