Viking aes-irda Service Manual
The AES-IrDA Interface is an add-on option board for the AES-
2000 Accessible Entry Systems. The AES-IrDA board provides
the AES-2000 with the capability to receive infrared communication as well as accept data from a card reader. The option board
is set up to supply power to the card reader as well as handle the
data in standard 26 bit Wiegand format. The board is designed
to work with HID Corporation proximity card readers. The data
from the card is compared to the pre-programmed keyless entry
codes stored in the AES-2000 system. If there is a match, the
AES-2000 will actuate the door strike as well as clock and date
stamp the event for logging purposes.
Add IrDA Control and Card Reader
Capability to Your AES-2000
PPhhoonnee......771155..338866..8888661
1
hhttttpp::////wwwwww..vviikkiinnggeelleeccttrroonniiccss..ccoom
m
• Mounting hardware included
• Allows remote control of the AES-2000
system
• Accepts data from HID card readers using
standard 26 bit Wiegand format
• Provides 5 volt power to the card reader
• Mounts behind the AES-2000 front panel
Power: Powered from AES-2000 control board
Dimensions: 38mm x 76mm (1.5” x 3.0”)
Shipping Weight: .45Kg (1 lb)
Environmental: -26° C to 54° C (-15° F to 130° F)
IrDA Control Distance: 1 meter
Card Reader Connection: Modular
Card Reader Power: 5 volt 100mA maximum
PPrraaccttiicce
e
T
T
EELLEECCOOM
M
S
S
OOLLUUTTIIOONNSSFFOORRTTHHE
E
221
1
SST
T
C
C
EENNTTUURRY
Y
TECHNICAL
TECHNICAL
FFeeaattuurrees
s
SSppeecciiffiiccaattiioonns
s
The IrDA transmitter-receiver allows the AES-2000 to be controlled from a hand held transmitter. Any of the front panel push buttons on the AES-2000 can be actuated from the hand held
transmitter. The information on the AES-2000 front panel display will appear on the display of
the hand held transmitter. Using this remote device, a person with limited physical abilities can
operate the entry system.
Note: The remote control features
require an IrDA hand held transmitter which is not yet available.
iinnffoo@@vviikkiinnggeelleeccttrroonniiccss..ccoom
m
PRELIMINARY
AES-IrDA
AES-IrDA
IrDA/Card Reader
Interface Board
March 15, 2002
Allows card entry in:
• Senior apartments
• Gated communities
• Dormitories
• Office complexes
• Secured areas
AApppplliiccaattiioonns
s
MMaaddeeiinntthheeUU..SS..AA.
.
IInnssttaallllaattiioon
n
Step 1. Unlock and open the AES-2000 front panel.
Step 2. Disconnect the power to the AES-2000.
Step 3. Remove the (4) screws holding the inner shroud and remove the shroud (see diagram A).
Step 4. Disconnect all cables to the control board.
Step 5. Remove the (4) mounting posts holding the control board (see diagram B).
Step 6. Lift off the control board and set it aside.
Step 7. Replace the left two nuts holding the lens with the standoffs provided (see diagram C).
Step 8. Mount the IrDA board onto the standoffs using the screws and washers provided (see diagram C and D).
Step 9. Re-mount the AES-2000 control board back onto the panel.
Step 10. Connect all cables and replace the inner shroud, being careful not to pinch any wires. The IrDA control cable connects to
J9 on the AES-2000 main board (see diagram).
Step 11. If a card reader is used, connect it to the modular cable coming from the IrDA interface board (see Wiring).
Step 12. Reconnect the power to the AES-2000, close and lock the front panel.
Diagram A
Diagram B
Diagram C
Diagram D
Side View
Screw
Fiber Washer
IrDA Board
Standoff
Lens
Front Panel of the AES-2000
Model: xxx
S/N: XXXXXX
Viking Electronics, Inc. (715)386-8861
P/N: xxxxxxx
1531 Industrial St., Hudson, WI 54016
VIKING
1
2
3
4
5
6
7
8
Loading...