Vigon VM-6185LED Installation And Operation Manual

www.vicon-security.com

Installation and Operation Manual

XX-204-10-00

LED Monitor

Vicon Industries Inc. does not warrant that the functions contained in this equipment will meet your requirements or that the
operation will be entirely error free or perform precisely as described in the documentation. This system has not been designed
to be used in life-critical situations and must not be used for this purpose.

Vicon Industries Inc. 131 Heartland Boulevard, Edgewood, NY 11717

Tel: [phone] Fax: [phone] Toll Free: 1-800-645-9116

24-Hour Technical Support: 800-34-VICON (800-348-4266) UK: +44 (0)1489/566300

Document Number: 8009-8204-10-00

Issued: 0614

Copyright © 2014 Vicon Industries Inc. All rights reserved.

Contents

Important Safeguards

Cautions

FCC Notice

Installation

Connecting with external equipment

Controls and functions

Mounting guide

D-SUB connector pin assignment

Power management

Specications

Troubleshooting guide

Shipping Instructions

Warranty

........................................................................................................

............................................................................................................................

........................................................................................................................

.........................................................................................................................

.................................................................................

.......................................................................................................

..................................................................................................................

.....................................................................................

..........................................................................................................

....................................................................................................................

.......................................................................................................

.........................................................................................................

............................................................................................................................

2 ~ 3

4

5

6

7

8 ~ 12

13

14

15

16

17

18

19

This Monitor was
Manufactured by ISO 9001

Certied Factory

- 1 -

Important Safeguards – Indoor Use

GRAPHIC SYMBOL EXPLANATION

The lightning bolt symbol alerts the user to the presence of dangerous
voltage that may present the risk of electric shock.

The exclamaon point symbol alerts the user to the presence of
important operang and maintenance instrucons.

WARNING

To reduce a risk of re or electric shock, do not expose this product to

rain or moisture.

26. Read Instrucons - Read all safety and operang instrucons

before the product is operated.

27. Retain Instrucons - Retain all safety and operang instrucons

for future reference.

28. Heed Warnings - Pay aenon to all product warnings.

29. Follow Instrucons - Follow all operang instrucons.

30. Installaon and W iring - The equipment and all devices connected

to it shall be installed and wired in accordance with the Naonal
Electrical Code, ANSl/NFPA 70.

31. Cleaning - (Do not use causc , abrasive or aerosol cleaners)

a) For units that CAN BE DISCONNECTED from the power source,

use a damp cloth for cleaning.

b) For units that CANNOT BE DISCONNECTED from the power

source, use a damp cloth for cleaning and do not allow
moisture or liquids to enter vents.

32. Aachments - Use only UL Listed Vicon recommended aachments

to prevent unit damage and personal injury.

33. Water and Moisture - Use only products designed for outdoor

environments where they will be exposed to water or moisture.

34. Accessories - Do not place the unit on an unstable surface to
avoid falling. Use only UL Listed Vicon recommended mounng

accessories.

35. Venlaon - Do not block venlang slots and openings as they

ensure reliable operaon. Do not place the unit near a heat source
or into an enclosure unless recommended by Vicon.

36. Grounding - Only products equipped with a 3-prong grounded
plug should be inserted into a grounded power outlet. Contact an
electrician to replace an obsolete outlet. Do not force a plug into a
non-grounded outlet.

37. Power Cord Protect ion - Power supply cords should not be routed
in tracked areas or in ght spaces where they will be pinched or
used to bear weight. Allow some slack in the cord where it enters

the unit.

38. Lightning - Disconnect the product from its power source and cable

system when possible to prevent damage due to lightning and

power-line surges.

39. Power Lines • Do not locate outside cables over power or ulity
lines where they can fall and make direct contact. Contact with
power lines can be fatal.

40. Overloading - Do not overload wall outlets and extension cords to
prevent risk of re and electric shock.

41. Object and Liquid Entry - Never probe through, or spill liquid into,
enclosure openings to prevent risk of re or electric shock.

42. Servicing - Refer all servicing to qualied service personnel.

43. Damage Requiring Service - Obtain service when:

a) The power-supply cord or plug is damaged.

b) Objects have fallen or liquid has been spilled into the product.

c) The product is not designed for outdoor use and has been

exposed to water or moisture.

d) The product does not operate per the operang instrucons.

Perform Vicon recommended adjustments, modicaons and
troubleshoong only to avoid unit damage and personal injury.

e) The product has been dropped.

f) The product shows a signicant change in performance.

44. Replacement Parts - Use only Vicon specied replacement parts or
an approved equivalent to prevent unit damage and injury.

45. Safety Check - Request safety checks to be performed following
repair or maintenance to verify proper operaon.

46. ESD Precauon - Take all normal electrostac discharge precauons
to avoid component damage during installaon and operaon.

47. For 230 VAC Devices Only - When the disconnect device is not
incorporated in the equipment or when the plug on the power
supply is intended to serve as the disconnect device, follow the
guidelines below:

a) For permanently connected 230 VAC units, a readily accessible

disconnect device must be incorporated into the site wiring.

b) For 230 VAC units with a plug, the outlet must be installed near

the unit and be easily accessible.

48. For Devices Requiring a Separate Power Supply - All devices

requiring a separate power supply shall be powered by a UL
Listed,Class 2 Power Supply.

49. Lithium Baeries Only:

WARNING

Fire and burn hazard. Do not recharge, disassemble, heat
above 212°F or incinerate. Keep baery out of reach of
children and in original package unl ready to use. Dispose
of used baeries promptly.

Risk of explosion if baery is replaced by incorrect type.
Dispose of used baeries according to the instrucons.

50. For Rack-Mounted Units Only – The following precauons apply to
all rack-mounted units.

a) Elevated Operang Ambient - If installed in a closed or mul-

unit rack assembly, the operang ambient temperature of

the rack environment may be greater than room ambient.

Therefore, consideraon should be given to installing the
equipment in an environment compable with the maximum
ambient temperature (Tma) specied by the manufacturer.

- 2 -

CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK,

DO NOT REMOVE COVER (OR BACK). NO USER:
SERVICEABLE PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL

Important Safeguards – Indoor Use(Cont)

b) Reduced Air Flow - Installaon of the equipment in a rack

should be such that the amount of air ow required for safe
operaon of the equipment is not compromised.

c) Mechanical Loading - Mounng of the equipment in the rack

should be such that a hazardous condion is not achieved due

to uneven mechanical loading.

d) Circuit Overloading - Consideraon should be given to the

connecon of the equipment to the supply circuit and
the eect that overloading of the circuits might have on
overcurrent protecon and supply wiring. Appropriate
consideraon of equipment nameplate rangs should be used
when addressing this concern.

e) Reliable Earthing - Reliable earthing of rack-mounted

equipment should be maintained. Parcular aenon should
be given to supply connecons other than direct connecons
to the branch circuit (e.g. use of power strips).

- 3 -

Cautions

CAUTION

The power supply cord is used as the main disconnect device, ensure that the socket-outlet is
located/installed near the equipment and is easily accessible.

ATTENTIONN

Le cordon d`alimentation est utillsé comme interrupteur général. La prise de courant doit être
située ou installée à proximité du matériel et être facile d`accès

► NEVER REMOVE THE BACK COVER

Removal of the back cover should be carried out only by qualied personnel.

► DO NOT USE IN HOSTILE ENVIRONMENTS

To prevent shock or re hazard, do not expose the unit to rain or moisture.
This unit is designed to be used in the ofce or home. Do not subject the unit to vibrations, dust

of corrosive gases.

► KEEP IN A WELL VENTILATED PLACE

Ventilation holes are provided on the cabinet to prevent the temperature from rising.
Do not cover the unit or place anything on the top of unit.

► AVOID HEAT

Avoid placing the unit in direct sunshine or near a heating appliance.

► TO ELIMINATE EYE FATIGUE

Do not use the unit against a bright back ground and where sunlight or other light sources will
shine directly on the monitor.

► BE CAREFUL OF HEAVY OBJECT

Neither the monitor itself nor any other heavy object should rest on the power cord.
Damage to a power cord can cause re or electrical shock.

- 4 -

FCC Notice

Note: Complies with Federal Communications Commission Rules & Regulations Part 15,

Subpart B for a Class A digital device.

Warning: Power must be removed from this unit before removing circuit modules or cables.

Caution: This unit contains circuit cards with integrated circuit devices that can be damaged

by static discharge. Take all necessary precautions to prevent static discharge.

WARNING

This equipment generates and uses radio frequency energy and if not installed and used properly,

that is, in strict accordance with the manufacturer’s instruction, may cause interference

to radio and television reception. It has been type tested and found to comply with the limits for a

Class A computing device in accordance with the specication in subpart B of part 15 of the FCC

rules, which are designed to provide reasonable protection against such interference in a commercial

installation. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause interference to radio and television reception, which can be determined

by turning equipment off and on, the user is encouraged to try and correct the interference by one or

more of the following measures:

- Reorient the receiving antenna.

- Relocate the equipment with respect to the receiver.

- Relocate the equipment away from the receiver.

- Plug the equipment into a different electrical outlet so that the equipment and
receiver are on different branch circuits.

If necessary, the user should consult the dealer or an experienced radio/television technician
for additional suggestions.

The user may nd the following booklet prepared by the Federal Communications Commission

helpful:
“Interference Handbook, Bulletin CIB-2”

This booklet is available from the U.S. Government Printing Ofce, Superintendent of

Documents, Mailstop SSOP, Washington, D.C. 20402-9328, ISBN 0-16-045542-1.

- 5 -

Before setting up the monitor, ensure that the power to the monitor and other attached

devices are turned off.

A-1. Place the monitor with its front facing downward on a soft cloth.

Adjust the position of the panel in various ways for maximum comfort. (Tilt Range: -3°~15°)

A-2. Assemble the Stand Base into the Stand Body in the correct direction using the included

A-3. Once assembled take the monitor up carefully and face the front side.

screws in the accessory box.

Notice: Stand & screws are optional

A. Connecting the stand

B. Positioning your display

- 6 -

Installation

15˚-3˚