C O M P U T E R S N E T W O R K S S O L U T I O N S
..
Vig660W
Motherboard
Manual
V1.0 Vig660W Motherboard Manual
1
Viglen, EMC and the ‘CE’ mark
CE Marking
European standards are being harmonised across borders. If products comply with the same standards in all
European countries, product exporting and importing is made simple - paving our way to a common market. If you buy
a product with a 'CE' mark on it (shown below), on the box, in the manual, or on the guarantee - it complies with the
currently enforced directive(s).
Introduction to EMC
EMC (Electromagnetic Compatibility) is the term used to describe certain issues with RF (Radio Frequency) energy.
Electrical items should be designed so they do not interfere with each other through RF emissions. E.g. If you turn on
your microwave, your television shouldn't display interference if both items are CE marked to the EMC directive.
If emitted RF energy is not kept low, it can interfere with other electrical circuitry - E.g. Cars Automatic Braking
Systems have been known to activate by themselves while in a strong RF field. As this has obvious repercussions
ALL electrical products likely to cause RF related problems have to be 'CE' marked from 1st January 1996 onwards.
If a product conforms to the EMC directive, not only should its RF emissions be very low, but its immunity to RF energy
(and other types) should be high. The apparatus has to resist many 'real world' phenomena such as static shocks and
mains voltage transients.
Viglen’s Environment laboratory
To gain a 'CE' mark, the Viglen computer range has had to undergo many difficult tests to ensure it is
Electromagnetically Compatible. These are carried out in the in-house 'Environment lab' at Viglen Headquarters. We
have made every effort to guarantee that each computer leaving our factory complies fully with the correct standards.
To ensure the computer system maintains compliance throughout its functional life, it is essential you follow these
guidelines.
Install the system according to Viglen’s instructions
If you open up your Viglen:
Keep internal cabling in place as supplied.
Ensure the lid is tightly secured afterwards
Do not remove drive bay shields unless installing a 'CE' marked peripheral in its place
The clips or ‘bumps' around the lips of the case increase conductivity - do not remove or damage.
Do not remove the ferrite ring from the L.E.D cables.
Only use your Viglen computer with 'CE' marked peripherals
This system has been tested in accordance with European standards for use in residential and light industrial areasthis specifies a 10 meter testing radius for emissions and immunity. If you do experience any adverse affects which
you think might be related to your computer, try moving it at least 10 meters away from the affected item. If you still
experience problems, contact Viglen’s Technical Support department who will put you straight through to an EMC
engineer - s/he will do everything possible to help. If modifications are made to your Viglen computer system, it might
breach EMC regulations. Viglen take no responsibility (with regards to EMC characteristics) of equipment which has
been tampered with or modified.
This symbol on the product or on its packaging indicates that the product shall not be treated as household
waste. Instead it shall be handed over to the applicable collection point for recycling of electrical and
electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential
negative consequences for the environment and human health, which could otherwise be caused by
inappropriate waste handling of this product. The recycling of materials will help to conserve natural
resources. For more detailed information about recycling of this product, please contact your local city
office, your household waste disposal service or Viglen Ltd.
V1.0 Vig660W Motherboard Manual
2
Copyrights and Trademarks
Please note
The material in this manual is subject to change without notice.
Trademarks
Microsoft, Windows XP Pro, Windows Vista, Windows 7 and MS-DOS are registered
trademarks of Microsoft Corporation. IBM PC, XT, AT and PS/2 are trademarks of
International Business Machines Corporation. Core i3/i5/i7TM and Pentium® are
registered trademarks of Intel® Corporation. All other trademarks are acknowledged.
Genie, Vig, Viglen, and Omnino are trademarks of Viglen Limited.
Copyright and Patents
This manual and all accompanying software and documentation are copyrighted and all
rights reserved. This product, including software and documentation, may not, in whole
or in part, be copied, photocopied, translated or reduced to any electronic or machinereadable form, without prior written consent except for copies retained by the purchaser
for backup.
© Copyright 2013 Viglen Limited
All Rights Reserved
Vig660W Manual Version 1.0
Printed in the United Kingdom
Liability
No warranty or representation, either expressed or implied, is made with respect to this
documentation, its quality, performance, merchantability or fitness for a particular
purpose. As a result the documentation is licensed as is, and you, the licensee, are
assuming the entire risk as to its quality and performance. The vendor reserves the right
to revise this operation manual and all accompanying software and documentation and
to make changes in the content without obligation to notify any person or organisation of
the revision or change.
In no event will the vendor be liable for direct, indirect, special, incidental or
consequential damages arising out of the use or inability to use this product or
documentation, even if advised of the possibility of such damages. In particular, the
vendor shall not have liability for any hardware, software or data stored or used with the
product, including the costs of repairing, replacing or recovering such hardware, software
or data.
V1.0 Vig660W Motherboard Manual
3
Contents
Chapter 1: Motherboard Overview 5
Introduction 5
Feature Summary 6
System Board Components 14
Back Panel Connectors 15
Chapter 2: System Board Options 16
Overview of Jumper Settings 17
System Board Jumper Settings 18
Motherboard Connectors 19
Upgrading the CPU 26
Installing & Removing Memory Modules 30
Replacing the Clock/CMOS RAM Battery 32
Chapter 3: Solving Problems 33
Resetting the System 33
Troubleshooting Procedures 34
Problems & Suggestions 35
Chapter 4: System BIOS 37
What is the BIOS? 37
The Power-On Sequence 37
BIOS Upgrades 38
Using AWDFLASH to Update the BIOS 38
BIOS Setup 39
Chapter 5: Suggestions 42
V1.0 Vig660W Motherboard Manual
4
Chapter 1: Motherboard Overview
Introduction
This manual describes the Viglen Vig660W motherboard inside your computer. The
motherboard is the most important part of your computer. It contains all of the CPU,
memory and graphics circuitry that make the computer work in the correct manner.
The Vig660W motherboard with Mini-ITX form factor offers premium features. Integrated
Graphics via VGA, HDMI, High Definition Audio via 2 flexible audio jacks and integrated
10/100/1000 network connection, as well as 4 USB 3.0 ports to enrich your multimedia
creation experience.
The Vig660W supports Intel Core i3, i5, i7 processors and Intel Pentium processors as
well as being Microsoft Windows 7 Premium WHQL certified.
This manual contains technical information about the Viglen Vig660W motherboard and
other hardware components inside your computer. If you are new to computers we
recommend that you read the user guide first. If you are an experienced computer user
this manual should provide all the information you will need to perform simple upgrades
and maintenance.
We hope that this manual is both readable and informative. If you have any comments
for suggestions about how we could improve the format then please fill out the form at
the back of the manual and send it to us.
Above all we hope that you enjoy using your Viglen computer.
V1.0 Vig660W Motherboard Manual
5
Feature Summary
Form factor:
Mini-ITX Form Factor: 170mm x 170mm
Processor:
Intel® Core™ i7, Intel® Core™ i5, Intel® Core™ i3, and Intel® Pentium®
processors in an LGA1155 socket
Integrated graphics processing (processors with Intel® Graphics
Technology)
External graphics interface controller
Integrated memory controller
Chipset
Intel® Q77 Express Chipset
Memory
Two 204-pin Double Data Rate 3 (DDR3) Small Outline Dual Inline
Memory Module (SO-DIMM) sockets
Support for DDR3 1066/1333/1600 MHz SO-DIMMs (DDR3 1066 MHz and
DDR3 1333 MHz SO-DIMMs operate at 800 MHz only)
Maximum 16GB Memory Size
Graphics
Integrated graphics support for processors with Intel® graphics technology
·Multi-VGA output support:1xD-SUB port; 1XHDMI® port supporting a
maximum resolution of 1920x1200@60HZ
Audio
Integrated HD audio codec by Realtek® ALC662
Support JACK detection, multi-streaming and anti-pop functions
With ALC105 amplifier to support speakers
Front panel header
LAN
Intel® 82579LM Gigabit LAN controller Supports 10/100/1000 Mbps/s Fast
Ethernet
V1.0 Vig660W Motherboard Manual
6
Rear I/O Ports
1 x 12V-19V Power Port
1x D-Sub (VGA)
1x HDMI
1x Gigabit LAN (Intel LAN PHY)
1x Microphone
1x Headphone/Speaker
4x USB 3.0 Ports
Internal Connectors
1 x Front Panel Connector
1 x 4-pin Chassis Speaker Connector
1x Front panel Audio Connector (2x5 pin)
1 x Front Panel Audio Connector (2 x 5 pin)
2 x USB 2.0 Connector Support 4 x USB 2.0 Ports (2 x 5 pin)
1x USB 2.0 Connector Supports 1x USB 2.0 Port (1x5 pin)
2 x SATA 6Gb/s Ports
1 x 4-pin CPU Fan Connector
1 x 4-pin ATX 12V/19V Power Connector
1 x 4-pin SATA Power_HDD Connector
1 x 3-pin SATA Power_ODD Connector
1 x 3-pin Clear CMOS Header
1 x Clear CMOS Jumper
Expansion Capabilities
·1x mini PCIE full card slot,support Intel® 310 series SSD cards or others with same pin define
·1x mini PCIE half card slot,support 802.11a/b/g/n WIFI and Bluetooth 3.0+HS
TPM
Nuvoton® NPCT420B TPM IC on board, support TPM 1.2
BIOS
AMI EFI BIOS
Intel® vPROTM Technology
Intel® Advanced Mangement Technology (Intel® AMT) 8.0
Intel® Trusted Execution Technology (Intel® TXT)
Intel® Virtualization Technology (Intel® VT)
Intel® Virtualization for Directed I/O(Intel® VT-d)
KVM Remote Control
V1.0 Vig660W Motherboard Manual
7
Processor
The motherboard is designed to support the Intel Core i7, Intel Core i5, Intel Core i3, and
Intel Pentium processors in an LGA1155 socket.
Other processors may be supported in the future. This board is designed to support
processors with a maximum TDP of 65 W.
Chipset
Intel Q77 Express Chipset with Intel Flexible Display Interconnect (Intel FDI) and
Direct Media Interface (DMI) interconnect provides interfaces to the processor and the
display, USB, SATA, LPC, LAN, and PCI Express interfaces. The Intel Q77 Express
Chipset is a centralized controller for the board’s I/O paths.
Memory
The board has two SO-DIMM sockets and supports the following memory features:
Two 204-pin DDR3 SDRAM Small Outline Dual Inline Memory Module (SODIMM)
sockets
Support for DDR3 1600 MHz, DDR3 1333 MHz, and DDR3 1066 MHz SODIMMs
Support for 1 Gb, 2 Gb, and 4 Gb memory technology
Support for up to 16 GB of system memory with two SO-DIMMs using 4 Gb
Memory technology
Support for non-ECC memory
Support for 1.5 V (standard voltage) and 1.35 V (low voltage) JEDEC memory
Support for XMP memory
Note: DDR3 1600 MHz SO-DIMMs are only supported by 3rd generation Intel
Core processor family processors
NOTE
To be fully compliant with all applicable DDR SDRAM memory specifications, the board
should be populated with SO-DIMMs that support the Serial Presence Detect (SPD) data
structure. This allows the BIOS to read the SPD data and program the chipset to
accurately configure memory settings for optimum performance. If non-SPD memory is
installed, the BIOS will attempt to correctly configure the memory settings, but
performance and reliability may be impacted or the SO-DIMMs may not function under
the determined frequency.
V1.0 Vig660W Motherboard Manual
8
Memory Configurations
The 3rd generation Intel Core processor family and 2nd generation Intel Core processor
Processors support the following types of memory organization:
• Dual channel (Interleaved) mode. This mode offers the highest throughput for real world
applications. Dual channel mode is enabled when the installed memory capacities of
both SO-DIMM channels are equal. Technology and device width can vary from one
channel to the other but the installed memory capacity for each channel must be equal. If
different speeds SO-DIMMs are used between channels, the slowest memory timing will
be used.
• Single channel (Asymmetric) mode. This mode is equivalent to single channel
bandwidth operation for real world applications. This mode is used when only a single
SO-DIMM is installed or the memory capacities are unequal. Technology and device
width can vary from one channel to the other. If different speed SO-DIMMs is used
between channels, the slowest memory timing will be used.
• Flex mode. This mode provides the most flexible performance characteristics. The
bottommost DRAM memory (the memory that is lowest within the system memory map)
is mapped to dual channel operation; the topmost DRAM memory (the memory that is
nearest to the 8 GB address space limit), if any, is mapped to single channel operation.
Flex mode results in multiple zones of dual and single channel operation across the
whole of DRAM memory. To use flex mode, it is necessary to populate both channels.
Graphics Subsystem
The board supports system graphics through either Intel Graphics Technology
Integrated Graphics
The board supports integrated graphics through the Intel® Flexible Display Interface
(Intel® FDI) for processors with Intel Graphics Technology.
NOTE: If using a processor with integrated graphics, the board will support only two of
the integrated graphics interfaces simultaneously: VGA, HDMI.
Analog Display (VGA)
The VGA port supports analog displays. The maximum supported resolution is 2048 x
1536 (QXGA) at a 75 Hz refresh rate. The VGA port is enabled for POST whenever a
monitor is attached, regardless of the DVI-D connector status.
High-Definition Multimedia Interface (HDMI)
The HDMI port supports standard, enhanced, or high-definition video, plus multichannel
digital audio on a single cable. It is compatible with all ATSC and DVB HDTV standards
and supports 8 full range channels at 24-bit/96kHz audio of lossless audio formats such
as Dolby TrueHD or DTS HD Master Audio. The maximum supported resolution is 1920
x 1200 at 60 Hz refresh (WUXGA).
The HDMI port is compliant with the HDMI 1.3 specification.
V1.0 Vig660W Motherboard Manual
9
Audio Subsystem
The motherboard supports Intel High Definition Audio through a Realtek ACL662 audio
codec. The following software features are supported
Compatible with Windows Vista Premium (complies with Microsoft WLP 3.08
specifications)
WaveRT-based audio function driver and logo ready for Windows Vista
Direct Sound 3D
™
compatible
A3D™ compatible
I3DL2 compatible
HRTF 3D Positional Audio
Friendly user interface for 2-foot or 10-foot remote control applications
Emulation of 26 sound environments to enhance gaming experience
10 Software Equalizer Bands
Voice Cancellation and Key Shifting in Karaoke mode
Windows Vista style configuration panel to improve user experience
Microphone Acoustic Echo Cancellation (AEC), Noise Suppression (NS), and
Beam Forming (BF) technology for voice application
Features Dolby
®
Digital Live and DTS® CONNECT™ software (Optional)
Features Dolby
®
Home Theater software (Optional)
These audio connectors are used for audio devices. It is easy to differentiate between
audio effects according to the colour of audio jacks.
Figure 1: Audio Connectors
Line-Out (Green) - Line Out, is a connector for speakers or headphones.
Mic (Pink) - Mic, is a connector for microphones.
V1.0 Vig660W Motherboard Manual
10
LAN Subsystem
The ethernet controllers support the following features:
• 10/100/1000 BASE-T IEEE 802.3 compliant
• Energy Efficient Ethernet (EEE) IEEE802.3az support (Low Power Idle [LPI]mode)
• Dual interconnect between the Integrated LAN Controller and the Physical Layer
(PHY):
PCI Express-based interface for active state operation (S0) state
SMBUS for host and management traffic (Sx low power state)
• Compliant to IEEE 802.3x flow control support
• 802.1p and 802.1q
• TCP, IP, and UDP checksum offload (for IPv4 and IPv6)
• Full device driver compatibility
In addition, the Intel 82579LM Gigabit Ethernet Controller supports Intel AMT, which is a
part of Intel’s vPro™ technology. The associated RJ-45 LAN connector has been colored
red for easy identification.
RJ-45 LAN Connector LEDs
The two LEDs are built into the RJ-45 LAN connector located on the back panel. These
LEDs indicate the status of the LAN as shown in Table 1.
Item
Description
A
Link/Activity LED (Green)
B
Link Speed LED (Orange/Yellow)
Figure 2: LAN Connector LED Locations
Table 1: LAN LED Status
LED
LED Colour
LED State
Description
Link
Green
Off
LAN activity is occurring.
On
LAN link is established.
Blinking
LAN activity is occurring.
Data
rate
Green/yellow
10 Mb/s data rate is selected.
100 Mb/s data rate is selected.
1000 Mb/s data rate is selected.
V1.0 Vig660W Motherboard Manual
11
Universal Serial Bus (USB)
The motherboard supports up to Eight USB ports. The port arrangement is a follows:
Four USB 3.0 ports are implemented with stacked back panel connectors (black)
Four USB 2.0 front panel ports are implemented through three dual-port internal
headers
NOTE: Computer systems that have an unshielded cable attached to a USB port may
not meet FCC Class B requirements, even if no device or a low-speed (sub-channel)
USB device is attached to the cable. Use shielded cable that meets the requirements for
high-speed (fully rated) devices.
SATA Support
The board provides two 6 GB/s SATA connectors, which support one device per
connector.
NOTE: By default the SATA mode is set to AHCI in the BIOS to improve system
performance. During Microsoft Windows XP installation, you must press F6 to install the
AHCI drivers. Both Microsoft Windows Vista and Microsoft Windows 7 include the
necessary RAID drivers for both AHCI and RAID without the need to install separate
RAID drivers using the F6 switch in the operating system installation process. It is
advised to install the latest AHCI drivers to improve system performance.
Expansion Slots
The motherboard provides the following expansion capability:
One PCI Express Half-Mini Card slot
One PCI Express Full-Mini Card slot
Real-Time Clock, CMOS SRAM, and Battery
A coin-cell battery (CR2032) powers the real-time clock and CMOS memory. When the
computer is not plugged into a wall socket, the battery has an estimated life of three
years. When the computer is plugged in, the standby current from the power supply
extends the life of the battery.
The clock is accurate to ± 13 minutes/year at 25 ºC with power applied through the
power supply 5V STBY rail.
NOTE: If the battery and AC power fail, date and time values will be reset and the user
will be notified during POST. When the voltage drops below a certain level, the BIOS
Setup program settings stored in CMOS RAM (for example, the date and time) might not
be accurate. Replace the battery with an equivalent one.
V1.0 Vig660W Motherboard Manual
12
BIOS
The BIOS provides the Power-On Self-Test (POST), the BIOS Setup program, and the
PCI/PCI Express and SATA auto-configuration utilities. The BIOS is stored in the Serial
Peripheral Interface (SPI) Flash memory device.
SATA Auto Configuration
If you install a SATA device (such as a hard disk drive) in your computer, the autoconfiguration utility in the BIOS automatically detects and configures the device for your
computer. You do not need to run the BIOS Setup program after installing a SATA
device. You can override the auto-configuration options by specifying manual
configuration in the BIOS Setup program.
BIOS Security Passwords
The BIOS includes security features that restrict whether the BIOS Setup program can
be accessed and who can boot the computer. A supervisor password and a user
password can be set for the BIOS Setup and for booting the computer, with the following
restrictions:
The administrator password gives unrestricted access to view and change all Setup
options. If only the administrator password is set, pressing <Enter> at the password
prompt of Setup gives the user restricted access to Setup.
If both the administrator and user passwords are set, you must enter either the
supervisor password or the user password to access Setup. Setup options are then
available for viewing and changing depending on whether the supervisor or user
password was entered.
Setting a user password restricts who can boot the computer. The password prompt
is displayed before the computer is booted. If only the supervisor password is set, the
computer boots without asking for a password. If both passwords are set, you can
enter either password to boot the computer.
V1.0 Vig660W Motherboard Manual
13
System Board Components
Figure 3: Motherboard Layout & Components
Table 2: Motherboard Connection
A
ATX12V 4PIN connector
J
DDR3 connector
B
USB2.0 X1 header
K
Front Panel header
C
SATA connector
L
Front panel USB2.0 header
D
mini PCIE full-card connector
M
Mini PCIE Half-card connector
E
SATA connector
N
Clear COM header
F
Power connector for SATA HDD
O
CPU FAN header
G
Power connector for SATA ODD
P
Speaker connector
H
System FAN header
Q
RTC battery connector
I
DDR3 connector
R
Front panel audio header
V1.0 Vig660W Motherboard Manual
14
Back Panel Connectors
The Motherboard external IO connectors are attached to a metallic I/O shield. This
shield serves several purposes:
• It protects the sensitive Motherboard from any external EMC interference.
• It stops the computer from interfering with other electrical devices.
• It allows the Motherboard to be easily upgraded in the future without having to
resort to buying a whole new case. Simply change the I/O shield to match the
Motherboard.
Figure 4: Back Panel Connectors
Power Jack – the board can be powered through a 19 V DC connector on the back panel.
The back panel DC connector is compatible with a 7.4 mm/OD (outer diameter) and 5.1
mm/ID (inner diameter) plug, where the inner contact is +19 (±10%) V DC and the shell is
GND. The maximum current rating is 12 A.
HDMI Port - The High-Definition Multimedia Interface (HDMI) is an all-digital audio/video
interface capable of transmitting uncompressed streams. HDMI supports all TV format,
including standard, enhanced, or high-definition video, plus multi-channel digital audio on a
single cable.
VGA Port - The DB15-pin female connector is provided for monitor.
USB 3.0 Port - The USB 3.0 port is for attaching USB devices such as keyboard, mouse, or
other USB compatible devices.
LAN Port - The standard RJ-45 LAN jack is for connection to the Local Area Network (LAN).
You can connect a network cable to it.
Audio Ports - These audio connectors are used for audio devices (MIC-IN, LINE-OUT).
Note:
The back panel audio line out connectors is designed to power headphones or amplified
speakers only. Poor audio quality occurs if passive (non-amplified) speakers are connected to
this output.
V1.0 Vig660W Motherboard Manual
15
Chapter 2: System Board Options
The Vig660W motherboard is capable of accepting Intel® Core i3, i5, i7 processors and
Intel Pentium processors. RAM can be upgraded to a maximum of 16GB using DDR3
1066 or 1333MHz RAM DIMMs Non ECC Unbuffered memory.
WARNING!
Unplug the system before carrying out the procedures described in this chapter.
Failure to disconnect power before you open the system can result in personal
injury or equipment damage. Hazardous voltage, current, and energy levels are
present in this product. Power switch terminals can have hazardous Voltages
present even when the power switch is off.
The procedures assume familiarity with the general terminology associated with
personal computers and with the safety practices and regulatory compliance
required for using and modifying electronic equipment.
Do not operate the system with the cover removed. Always replace the cover
before turning on the system.
As the colours of the wires in the mains lead of this computer may not correspond with the
coloured markings identifying the terminals in your plug precede as follows:
The wire which is coloured green-and-yellow must be connected to the terminal in the plug
which is marked by the letter E or by the safety Earth symbol Q or coloured green or green-
and-yellow.
The wire which is coloured blue must be connected to the terminal which is marked with the
letter N or coloured black.
The wire which is coloured brown must be connected to the terminal which is marked with the
letter L or coloured red.
Make sure you are earthed and free of static charge before you open the computer case.
If you are unsure about upgrading your computer, return it to Viglen so a qualified
engineer can perform the upgrade.
CAUTION!
The Viglen Vig660W motherboard
and associated components are
sensitive electronic devices. A small
static shock from your body can
cause expensive damage to your
equipment.
V1.0 Vig660W Motherboard Manual
16
STEPS TO TAKE TO PREVENT STATIC DISCHARGE:
1. The best way to prevent static discharge is to buy an anti-static strap from your local
electrical shop. While you are wearing the strap and it is earthed, static charge will be
harmlessly bled to ground.
2. Do not remove the component from its anti-static protective packaging until you are
about to install it.
3. Hold boards by the edges - try not to touch components / interface strips etc.
NOTE: We recommend that you return your computer to the service department for
upgrading. Any work carried out is fully guaranteed. Upgrades should only be carried out
by persons who are familiar with handling IC's, as incorrect installation will invalidate the
guarantee.
V1.0 Vig660W Motherboard Manual
17
System Board Jumper Settings
Do not move the jumper with the power on. Always turn off the power and unplug the
power cord from the computer before changing a jumper setting. Otherwise, the board
could be damaged.
Clear CMOS Jumper: CLR_CMOS
The configuration Jumper (CLR_CMOS) allows the user to clear the CMOS. The CMOS
RAM onboard has a power supply from an external battery to keep the data of the
system configuration. The CMOS RAM allows the system to automatically boot OS every
time it is turned on.
Pin
Status
1-2
Normal
2-3
Clear CMOS
Figure 5: Clear CMOS jumper
V1.0 Vig660W Motherboard Manual
18
Motherboard Connectors
There are connectors on the motherboard for the Power supply, HD audio, fans, front
panel audio, front panel USB ad front panel connectors. The location and/or details of
these connections are shown below.
Front Panel Connectors
Front Panel Connectors: Sys_Panel
These connectors are for electrical connection to the front panel switches and LEDs. The
Sys_Panel is compliant with Intel® Front Panel I/O Connectivity Design Guide.
Figure 6: Front Panel Connectors
Table 3: Front Panel Connectors (Sys_Panel)
Pin
Connector
Comments
1-3
Hard Drive Activity LED
Header
Pins 1 and 3 can be connected to an LED to provide a visual
indicator that data is being read from or written to a hard drive.
Proper LED function requires a Serial ATA hard drive connected to
an onboard Serial ATA connector.
5-7
Reset Switch Header
Pins 5 and 7 can be connected to a momentary single pole, single
throw (SPST) type switch that is normally open. When the switch is
closed, the board resets and runs the POST.
2-4
Power/Sleep LED Header
Pins 2 and 4 can be connected to a one- or two-colour LED. This
display if the computer is active or not.
6-8
Power Switch Header
Pins 6 and 8 can be connected to a front panel momentary-contact
power switch. The switch must pull the SW_ON# pin to ground for at
least 50 ms to signal the power supply to switch on or off. (The time
requirement is due to internal debounce circuitry on the board.) At
least two seconds must pass before the power supply will recognize
another on/off signal.
V1.0 Vig660W Motherboard Manual
19
Power Connectors
ATX 12V 4PIN Power Connector: Power_In
This 12V power connector is used to provide power directly to the CPU voltage regulator
and must be used. Failure to do so will prevent the motherboard from booting.
Figure 7: ATX 12V 4-PIN power connector
Table 4: ATX 12V 4PIN connector
PIN
Signal name
1
GND
2
GND
3
DC power in
4
DC power in
NOTE:
Note: DC power in can be within 12-19V (>=120W) with this motherboard。Users can
use ATX12V 4pin header plugged to this header, but have to make method to let it output
12-19V power before powering on the motherboard.
V1.0 Vig660W Motherboard Manual
20
Front Panel Audio Connector: FP_AUDIO
This connector allows you to connect the front panel audio and is compliant with Intel®
Front Panel I/O Connectivity Design Guide.
Figure 8: Front panel audio connector
Table 5: Front panel audio header for HD audio
Pin
Signal Name
Pin
Signal Name
1
[Port 1] Left channel
2
Ground
3
[Port 1] Right channel
4
PRESENCE# (Dongle present)
5
[Port 2] Right channel
6
[Port 1] SENSE_RETURN
7
SENSE_SEND (Jack detection)
8
Key (no pin)
9
[Port 2] Left channel
10
[Port 2] SENSE_RETURN
Table 6: USB2.0 X1 header
PIN
Signal name
1
+5VDC
2
D- 3 D+ 4 GND
5
Key(no pin)
V1.0 Vig660W Motherboard Manual
21
Front USB Connector: USB20_34, USB20_12
This connector, compliant with Intel® I/O Connectivity Design Guide, is ideal for
connecting high-speed USB interface peripherals such as USB HDD, digital cameras,
MP3 players, printers, modems and the like.
Figure 9: Front USB connectors
Table 7: Front panel USB2.0 header
Pin
Signal Name
Pin
Signal Name
1
+5 VDC
2
+5 VDC
3
D- 4 D- 5 D+ 6 D+ 7 Ground
8
Ground
9
KEY (no pin)
10
No Connect
V1.0 Vig660W Motherboard Manual
22
Fan Power Connectors: CPUFAN, SYSFAN1~2
The fan power connectors support system cooling fan with +12V. When connecting the
wire to the connectors, always note that the red wire is the positive and should be
connected to the +12V; the black wire is Ground and should be connected to GND. The
motherboard has a System Hardware Monitor chipset on-board, which must be used with
fans specially designed with speed sensors to take advantage of the CPU fan control.
Figure 10: Fan Power connectors
Table 8: System FAN header, CPU FAN header
PIN
4-Wire support
PIN
3-Wire support
1
GND
3
GND
2
+12V main power
2
FAN_POWER
3
FAN_TACH
1
FAN_TACH
4
FAN_CONTROL
N/A
N/A
V1.0 Vig660W Motherboard Manual
23
Serial ATA Connector: SATA1 ~ SATA1
This connector is a high-speed Serial ATA interface port. Each connector can connect to
one Serial ATA device.
Figure 11: Serial ATA Connector
NOTE:
Please do not fold the serial ATA cable into 90-degree angle. Otherwise, data loss may
occur during transmission.
Power Supply Connectors
The board has the following power supply connectors:
• External Power Supply – the board can be powered through a 19 V DC connector on
the back panel. The back panel DC connector is compatible with a 7.4 mm/OD (outer
diameter) and 5.1 mm/ID (inner diameter) plug, where the inner contact is +19 (±10%) V
DC and the shell is GND. The maximum current rating is 12 A.
V1.0 Vig660W Motherboard Manual
24
Upgrading the CPU
CAUTION!
Before installing or removing a processor, make sure the AC power has been removed
by unplugging the power cord from the computer; the standby power LED should not be
lit. Failure to do so could damage the processor and the board.
To install a processor, follow these instructions:
1. Unlatch the processor socket lever by pushing it down and away from the socket.
(Figure 12, A, B)
Figure 12: Unlatch the socket lever
2. Rotate the socket lever to lift the load plate away from the socket (Figure 13, A).
Make sure that the load plate is in the fully open position (Figure 13, B) while being
careful not to damage adjacent components. Do not touch the socket contacts.
Figure 13: Lift the load plate
V1.0 Vig660W Motherboard Manual
25
3. Remove the processor from its protective cover. Hold the processor only at the
edges, being careful not to touch the bottom of the processor (see Figure 14).
Figure 14: Remove the processor from the protective cover
Note: Do not discard the processor cover. Always replace the processor cover if you
remove the processor from the socket.
4. Hold the processor with your thumb and index finger oriented as shown in Figure 15
to align your fingers with the socket finger cut-outs. Make sure that the processor Pin
1 indicator (gold triangle) is aligned with the Pin 1 chamfer on the socket (Figure 15,
B) and that the notches on the processor align with the posts on the socket (Figure
15, C). Lower the processor straight down without tilting or sliding it in the socket
(Figure 15, A).
Figure 15: Install the processor
V1.0 Vig660W Motherboard Manual
26
5. Carefully lower the socket lever (Figure 16, A) while making sure that the front edge
of the load plate slides under the shoulder screw cap as the lever is lowered. Latch
the socket lever under the load plate tab (Figure 16, C, and D). The socket cover
(Figure 16, B) will pop off as shown.
Figure 16: Secure the load plate in place
6. Pick up the socket cover and remove it from the desktop board.
V1.0 Vig660W Motherboard Manual
27
Connecting the Processor Fan Heat Sink Cable
Connect the processor fan heat sink power cable to the 4-pin processor fan header (see
Figure 17). A fan with a 4-pin connector as shown in Figure 17 is recommended.
1. Make sure the four hooks are in the proper position before you install the cooler.
Figure 17: Connecting the processor fan heat sink power cable to the processor fan header
V1.0 Vig660W Motherboard Manual
28
Installing & Removing Memory Modules
Installing Memory
You can install from 512MB to 8GB of memory in the motherboard DIMM sockets. The
motherboard has two DIMM sockets. The motherboard supports the following memory
features:
o Two DDR3 SO-DIMMs with gold-plated contacts.
o Non-ECC (64-bit) memory.
o 1GB, 2GB, 4GB and 8GB modules.
o Memory Speeds 1066MHz and 1333MHz
To install DIMMs, follow these steps:
1. Observe the precautions in “Before You Begin”. Turn off the computer and all
Peripheral devices.
2. Remove the computer cover and locate the DIMM sockets.
3. Holding the SO-DIMM by the edges, remove it from its antistatic package.
4. Position the SO-DIMM above the socket. Align the two small notches in the bottom
edge of the SO-DIMM with the socket tabs. Insert the bottom edge of the SO-DIMM
into the socket.
5. When the SO-DIMM is seated, push down until the retaining arms at either ends of
the socket snap into place. Make sure the clips are firmly in place.
6. Replace the computer cover.
Figure 18: Memory Installation
V1.0 Vig660W Motherboard Manual
29
Removing Memory
To remove a SO-DIMM, follow these steps:
1. Observe the precautions in "Before You Begin”.
2. Turn off all peripheral devices connected to the computer. Turn off the computer.
3. Remove the computer cover.
4. Gently spread the retaining arms at each end of the socket. The SO-DIMM pops out
of the socket. Hold the SO-DIMM by the edges, lift it away from the socket, and store
it in an antistatic package.
5. Reinstall and reconnect any parts you removed or disconnected to reach the SO-
DIMM sockets.
Figure 19: Removing Memory Modules
V1.0 Vig660W Motherboard Manual
30
Replacing the Clock/CMOS RAM Battery
A lithium battery is installed in a socket on the system board.
The battery has an estimated life expectancy of seven years. When the battery starts to
weaken, it loses voltage; when the voltage drops below a certain level, the system
settings stored in CMOS RAM (for example, the date and time) may be wrong.
If the battery fails, you will need to replace it with a CR2032 battery or an equivalent. As
long as local ordinance permits, you may dispose of individual batteries as normal
rubbish. Do not expose batteries to excessive heat or any naked flame. Keep all
batteries away from children.
CAUTION!
Danger of explosion if the battery is incorrectly replaced. Replace only with the same or
equivalent type recommended by Viglen. Discard used batteries according to
manufacturer’s instructions.
To replace the battery, carry out the following:
1. Observe the precautions in “Before You Begin.”
2. Turn off all peripheral devices connected to the system.
3. Turn off the system.
4. Remove any components that are blocking access to the battery.
5. Figure 24 shows the battery location. Gently pry the battery free from its socket.
6. Install the new battery in the socket.
Figure 20: Removing the Battery
V1.0 Vig660W Motherboard Manual
31
Chapter 3: Solving Problems
The first part of this chapter helps you identify and solve problems that might occur when
the system is in use. The second part lists error code messages that might be displayed.
Please remember that if you cannot solve the problem by yourself then you should
contact Viglen Technical Support for further assistance.
Viglen Technical Support can be reached in the following ways:
Telephone: 01727 201 850
Fax: 01727 201 858
Email: techsupport@viglen.co.uk
You can also look for support information on our web site:
http://www.viglen.co.uk
Device drivers and various useful utilities can be downloaded from our ftp site:
http://download.viglen.co.uk/files/
Resetting the System
Before checking your system for hardware problems, it is always a good idea to try
resetting your computer and see if a re-boot can solve the problem. Most software
related problems can be solved simply by re-booting your PC.
Table 9: Resetting the System
To do the following
Press
Soft boot: Clear the system memory and
reload the operating system (also called
warm reset).
<Ctrl + Alt + Del>
Cold boot: Clear the system memory, halt
power to all peripherals, restart POST, and
reload the operating system.
Power off/on or reset button (at front
of the system)
V1.0 Vig660W Motherboard Manual
32
Troubleshooting Procedures
This section provides a step-by-step troubleshooting procedure to identify a problem and
locate its source.
CAUTION!
1. Turn off the system and any peripheral devices before you disconnect any peripheral
cables from the system. Otherwise, you can permanently damage the system or the
peripheral devices.
2. Make sure the system is plugged into a properly grounded power outlet.
3. Make sure your keyboard and video display are correctly connected to the system.
Turn on the video display, and turn up its brightness and contrast controls to at least
two-thirds of the maximum (refer to the documentation supplied with the video
display).
4. If the operating system normally loads from the hard disk drive, make sure there is no
diskette in the diskette drive. If the operating system normally loads from a diskette,
insert the operating system diskette into the drive.
5. Turn on the system. If the power indicator does not light, but the system seems to be
operating normally, the indicator is probably defective. Monitor the power-on self test
(POST) execution. Each time you turn on the system, the POST checks the system
board, memory, keyboard, and certain peripheral devices.
NOTE: If the POST does not detect any errors, the system beeps once and boots up.
Errors that do not prevent the boot process (non-fatal errors) display a message that
looks similar to the following:
Error Message Line 1
Error Message Line 2
Press <DEL> for Set-up, <F1> to Boot
You can note the error and press <F1> to resume the boot-up process, or <DEL>
to enter Set-up.
Errors that prevent the boot process from continuing (fatal errors), are communicated by
a series of audible beeps. If this type of error occurs, refer to the error codes and
messages listed at the end of this chapter.
6. Confirm that the operating system has loaded.
V1.0 Vig660W Motherboard Manual
33
Problems & Suggestions
Table 10: Problems and Suggestions
What happens
What to do
Application software
problems
Try resetting the system.
Make sure all cables are installed correctly.
Verify that the system board jumpers are set properly.
Verify that your system hardware configuration is set correctly. In
Setup, check the values against the system settings you recorded
previously. If an error is evident (wrong type of drive specified, for
example), make the change in Setup and reboot the system. Record
your change.
Make sure the software is properly configured for the system. Refer to
the software documentation for information.
Try a different copy of the software to see if the problem is with the
copy you are using.
If other software runs correctly on the system, contact the vendor of
the software that fails.
If you check all of the above with no success, try clearing CMOS
RAM and reconfiguring the system. Make sure you have your list of
system settings available to re-enter, because clearing CMOS RAM
sets the options to their default values.
Characters onscreen are distorted
or incorrect
Make sure the brightness and contrast controls are properly adjusted
on the monitor.
Make sure the video signal cable and power cables are properly
installed.
Make sure your monitor is compatible with the video mode you have
selected.
Characters do not
appear on screen
Make sure the video display is plugged in and turned on.
Check that the brightness and contrast controls are properly adjusted.
Check that the video signal cable is properly installed.
Make sure a video board is installed, enabled, and the jumpers are
positioned correctly.
Reboot the system.
V1.0 Vig660W Motherboard Manual
34
Table 11: Problems and Suggestions (Continued)
What happens
What to do
CMOS RAM settings
are wrong
If system settings stored in CMOS RAM change for no apparent
reason (for example, the time of day develops an error), the backup
battery may no longer have enough power to maintain the settings.
Replace the battery (Chapter 2).
Diskette drive light
does not go on when
drive is in use or is
tested by POST
Make sure the power and signal cables for the drive are properly
installed.
Check that the drive is properly configured and enabled in Setup.
Hard drive light does
not go on when drive
is in use or is tested
by POST
Make sure the power and signal cables for the drive are properly
installed.
Make sure the front panel connector is securely attached to the
system board headers.
Check that the drive is properly configured and enabled in Setup.
Check the drive manufacturer's manual for proper configuration for
remote hard disk drive activity.
Power-on light does
not go on
If the system is operating normally, check the connector between the
system board and the front panel. If OK, the light may be defective.
Prompt doesn't
appear after system
boots
It’s probably switched off.
A serious fault may have occurred consult your dealer service
department / Technical Support.
Setup, can't enter
If you can't enter Setup to make changes, check the switch that
disables entry into Setup (Chapter 2). If the switch is set to allow
entry into Setup, you might need to clear CMOS RAM to the default
values and reconfigure the system in Setup.
System halts before
completing POST
This indicates a fatal system error that requires immediate service
attention. Note the screen display and write down any beep code
emitted. Provide this information to your dealer service department /
Technical Support.
V1.0 Vig660W Motherboard Manual
35
Chapter 4: System BIOS
What is the BIOS?
The BIOS (Basic Input Output System) is an important piece of software which is stored
in a ROM (Read Only Memory) chip inside the computer. It consists of the basic
instructions for controlling the disk drives, hard disk, keyboard and serial/parallel ports.
The BIOS also keeps a list of the specifications of the computer in battery-backed RAM
(also known as the CMOS RAM) and provides a special Setup program to change this
information.
The BIOS in your Viglen computer is guaranteed to be fully compatible with the IBM
BIOS. It has been written by Phoenix Award BIOS, an industrial leader in the field of
BIOS software.
The Power-On sequence
When the computer is first switched on, certain instructions in the BIOS are executed to
test various parts of the machine. This is known as the POST (Power-On Self Test)
routine. When you switch the computer on (or when you press the Reset button or press
<Ctrl> + <Alt>+ <Delete> keys, which has the same effect), you can see on the monitor
that it counts through the memory, testing it. The floppy disk drives are then accessed
and tested, and the various interfaces are checked. If there are any errors, a message is
displayed on the screen.
V1.0 Vig660W Motherboard Manual
36
BIOS Upgrades
A new version of the BIOS can be upgraded from a bootable USB key using the
AMIDEDOS.EXE utility or in Windows using the AEFUWIN utility that is available from
the Viglen FTP site. This utility does BIOS upgrades as follows:
Updates the flash BIOS from a file on a disk or within the location of the utility.
Updates the language section of the BIOS.
Makes sure that the upgrade BIOS matches the target system to prevent accidentally
installing BIOS for a different type of system.
BIOS upgrades and the AMIDEDOS.EXE utility is available on the Viglen FTP site
http://download.viglen.co.uk/files/
NOTE: Please review the instructions distributed with the upgrade utility before
attempting a BIOS upgrade.
Using AMIDEDOS.EXE to update the BIOS
The BIOS can be updated using the AMIDEDOS.EXE utility in DOS environment.
1. Save BIOS update zipped file to a temporary directory.
2. Extract the necessary files.
3. Copy the contents of the file to a bootable floppy disk, USB device or CD-ROM.
4. Boot the target PC with the device connected or inserted.
5. Select F7 during POST to display the Boot Menu and select your bootable device.
6. Type 'Flash.bat' to launch the BIOS update process.
7. The system will reboot once complete.
DO NOT shutdown or reset the system while updating the BIOS! Doing so may
cause system boot failure!
When the BIOS update process is complete, the utility reboots the system.
Once the system has been restarted following need to be completed before starting
windows.
1. Enter the BIOS setup by pressing DEL
2. Once in the setup load the optimized settings by selecting ‘Load Optimized
Defaults’
3. Exit the setup by selecting ‘Save & Exit setup’.
4. Now boot in to windows.
V1.0 Vig660W Motherboard Manual
37
BIOS Setup
This chapter provides basic information on the BIOS Setup program and allows you to
configure the system for optimum use. You may need to run the Setup program when:
An error message appears on the screen during the system booting up, and requests
you to run BIOS SETUP.
You want to change the default settings for customized features.
Note: The items under each BIOS category described in this chapter are under
continuous update for better system performance. Therefore, the description may be
slightly different from the latest BIOS and should be held for reference only.
Entering Setup
Power on the computer and the system will start POST (Power On Self Test) process.
When the message below appears on the screen, press <DEL> key to enter Setup.
Press DEL to enter Setup Menu, F11 to enter Boot Menu
If the message disappears before you respond and you still wish to enter Setup, restart
the system by turning it OFF and On or pressing the RESET button. You may also restart
the system by simultaneously pressing <Ctrl>, <Alt>, and <Delete> keys.
Control Keys
Table 12: BIOS control keys
<← →>
Select Screen
↑↓
Select Item
<Enter>
Select
+/-
Change Opt
F1:
General help
F2:
Previous values
F3:
Optimized Defaults
F4:
Save & Exit
ESC:
Exit
Getting Help
After entering the Setup menu, the first menu you will see is the Main Menu.
Main Menu
The main menu lists the setup functions you can make changes to. You can use the
arrow keys ( ↑↓ ) to select the item. The on-line description of the highlighted setup
function is displayed at the bottom of the screen.
V1.0 Vig660W Motherboard Manual
38
Sub-Menu
If you find a right pointer symbol (as shown in the right view) appears to the left of certain
fields that means a sub-menu can be launched from this field. A sub-menu contains
additional options for a field parameter. You can use arrow keys ( ↑↓ ) to highlight the
field and press <Enter> to call up the sub-menu. Then you can use the control keys to
enter values and move from field to field within a sub-menu. If you want to return to the
main menu, just press the <Esc >.
General Help <F1>
The BIOS setup program provides a General Help screen. You can call up this screen
from any menu by simply pressing <F1>. The Help screen lists the appropriate keys to
use and the possible selections for the highlighted item. Press <Esc> to exit the Help
screen.
The Menu Bar
Figure 21: Main Menu Bar
Main Menu - Use this menu for basic system configurations, such as time, date etc.
Advanced - Use this menu to setup the items of the BIOS special enhanced features,
integrated peripherals, power management and PC health status.
Overclocking - Use this menu to specify your settings for frequency/voltage control
and overclocking.
Monitor - For changing the system monitor configuration settings.
Boot - Use this menu to specify the priority of boot devices.
Security - Use this menu to set supervisor and user passwords.
Save & Exit - This menu allows you to load the BIOS default values or factory
V1.0 Vig660W Motherboard Manual
39
When enter the BIOS Setup utility, follow the processes below for general use.
1. Load Optimized Defaults: Use the arrow keys (←, →, ↑, ↓) to select the [Restore
Defaults] in [Save & Exit] menu, and press <Enter>. A pop-up message will appear,
select [Yes] and press <Enter> to load the default settings for optimal system
performance.
Figure 22: Restore Defaults
2. Setup Date/Time: Use the arrow keys (←, →, ↑, ↓) to select the [System Date] /
[System Time] in [Main Menu] menu, and press <Enter>. And then, you can set the
Date, Time in their respective fields.
Figure 23: Setup Date/Time
3. Save & Exit Setup: Use the arrow keys (←, →, ↑, ↓) to select the [Save Changes &
Reset] in [Save & Exit] menu, and press <Enter>. A pop-up message will appear,
please select [Yes] and press<Enter> to save the configurations and exit BIOS setup
utility.
Figure 24: Save & Exit Setup
V1.0 Vig660W Motherboard Manual
40
Windows 8 BIOS Setting
System configured with Windows 8 64bit operating system will have following default
BIOS settings. It is strongly recommended that these BIOS settings are not disabled for a
Windows 8 64Bit Operating system.
Fast BOOT [Enabled]
UEFI Boot [Enabled]
Secure Boot [Enabled]
To enable downgrade to Windows 7 on this system the BIOS settings must be changed
to boot into Legacy BIOS mode. Above BIOS settings should be changed to [Disabled]
Note
Please ensure the changes of the following settings are performed by personnel with some
previous experience/knowledge of altering BIOS settings.
Accessing BIOS Setup
To access the BIOS, when the system is powered on repeatedly press the [DEL] key to
access BIOS setup screen once the Windows 8 setup is complete to re-access the BIOS
you will need to power down the system and wait 20 seconds before powering up the
system; on power on Press the {DEL} key to access BIOS setup.
Enabling/Disabling Windows 8 Features
1. From the BIOS main menu select the ‘Boot’ tab.
Figure 25: Main menu
2. In the ‘Boot’ tab scroll down the options to ‘Fast Boot’ and select this option. Set
the ‘Fast Boot’ option to ‘Enabled’.
V1.0 Vig660W Motherboard Manual
41
Figure 26: Boot Menu
Fast Boot’ - It is recommended that this option is ‘Enabled’ for Windows 8 operating systems to
ensure the boot up sequence is performed at the fastest possible time.
3. In the ‘Boot’ tab scroll down the options to ‘UEFI Boot’ and select this option. Set
the ‘UEFI Boot’ option to ‘Enabled’. For Windows 7 and Windows XP operating
systems it should be set to Disabled.
Figure 27: UEFI Boot option
V1.0 Vig660W Motherboard Manual
42
Enabling /Disabling Secure Boot
‘Secure Boot’ it is recommended this setting is set to ‘Enabled’ to initialize the Windows
8 secure boot feature when the system boots up.
Note: Secure boot is supported under Windows 8 64Bit Operating system. This
feature helps in preventing malicious software applications and "Unauthorized" operating
systems from loading during the system start-up process.
To Enable Secure Boot
From the BIOS tab options select the ‘Security’ tab and select the ‘Secure Boot’ option,
set the ‘Secure Boot’ option to ‘Enabled’
Figure 28: Secure Boot Enabled/Disabled option
V1.0 Vig660W Motherboard Manual
43
1. Once Secure Boot is set to ‘Enabled’ scroll down the active options from the
Security Tab options and Set the Secure Boot Mode to ‘Custom’
Figure 29: Secure Boot Enabled/Disabled option
2. In Custom mode scroll down the active options in the Security Tab option list and
Select the ‘Key Management’ Option.
Figure 30: Secure Boot
V1.0 Vig660W Motherboard Manual
44
3. In the Key management options select the ‘Default Key Provisioning’ option
and Set to ‘Enabled’
Figure 31: Default Key Provisioning
4. In the Key management options select the ‘Install default Secure Boot Keys’
option and confirm Installation in the prompt pop up to install the default secure
Boot Keys.
Figure 32: Default Secure Boot Keys
V1.0 Vig660W Motherboard Manual
45
5. Once the Default Secure Boot keys are installed it will state ‘Installed’ as shown in
below image
Figure 33: Default Secure boot keys
V1.0 Vig660W Motherboard Manual
46
Disabling Secure Boot
1. In the Key management options select ‘Default Key Provisioning’ and Set the
option to ‘Disabled’
Figure 34: Default Key Provisioning
2. Select ‘Clear Secure Boot Keys’ and confirm Installation in the prompt pop up to
clear the default secure Boot Keys.
Figure 35: Reset platform
V1.0 Vig660W Motherboard Manual
47
3. Once the secure Boot keys are cleared it will state ‘Not Installed’ as shown in
below
Figure 36: Clear Secure Boot Keys’
4. Press Esc to exit the Key provisioning Menu.
5. Select ‘Secure Boot’ and set the option to ‘Disabled’
Figure 37: Disabling Secure boot
Once all BIOS settings have been configured press F4 key to Save and Exit the BIOS
Setup.
For Non EFI OS support (Windows 7) secure boot keys must be set to default and secure boot
disabled. Otherwise system will not detect SATA hard disk drive under boot menu.
V1.0 Vig660W Motherboard Manual
48
Chapter 5: Suggestions
Viglen is interested in continuing to improve the quality and information provided in their
manuals. Viglen has listed some questions that you may like to answer and return to
Viglen. This will help Viglen help to keep and improve the standard of their manuals.
1. Is the information provided in this and other manuals clear enough?
2. What could be added to the manual to improve it?
3. Does the manual go into enough detail?
4. Would you like an on-line version of this manual?
5. How do you rate the Viglen Technical support and Service Departments?
V1.0 Vig660W Motherboard Manual
49
6. Are there any technological improvements that could be made to the system?
7. Other points you would like to mention?
Please return this slip to: Product Development Dept.
Viglen Ltd.
7 Handley Page Way
Colney Street
St Albans
Hertfordshire
AL2 2DQ
V1.0 Vig660W Motherboard Manual
50
Notes
Loading...