Viglen Genie Ultra Micro Getting Started Manual

Viglen Getting Started Guide

Genie Ultra Micro

Included fittings

If you purchased your Genie Ultra Micro from Viglen, the fitting lugs (2x screw A) will already be in place.
Otherwise you will need to fit the lugs shown below.

1 2 3 4

1 2 3

4

Step 1 Mounting the cable cover

u Ensure that screws A are fitted

to chassis. Align the chassis
onto the monitor stand and slot
into place.

u Slot the chassis down into the

slots marked 2 to lock into
place (figure 1).

u Turn the retaining clips to

secure the chassis and lock the
chassis using optional screws B
provided through the low holes
on the retaining clips (figure 2).

Step 2 Attach the chassis to the stand

u Ensure that screws C are fitted

to the two bottom monitor VESA
points (figure 1). Align the rear
VESA mount of the monitor with
the VESA bracket on the
monitor stand.

u Ensure the monitor is now

slotted in place on the VESA
plate (figure 2).

u Hold the monitor in place and

secure it using the screws D
provided to the upper holes
(figure 3).

Step 3 Securing the monitor to the stand

6

Screw A Screw B Screw C Screw D Cable Cover Block

( x 2 ) ( x 2 ) ( x 2 ) ( x 2 ) ( x 1 )

Screw A

6

Tools required

Cross-head screwdriver

Additional parts

Depending on the configuration you purchased,
you may also receive the following items:

u Internal Speaker (mounted in the Cable Cover)

u Split Mains Power Cable for the base unit and monitor

(includes a converter for the AC adapter)

Start Guide - Genie Ultra Micro (2009-06)

5

5

Screw B

Screw C

Screw D

u Feed all cables through the aperture in the bottom of the

cable cover and attach them to the ports on the
motherboard, including the cables from the optional
monitor stand and optional internal speaker.

u Slide the AC Adapter into the cable cover and insert the

retaining block (figure 1 and 2).

u Attach the power connector to the power socket at the

rear of the chassis (figure 3).

u Attach the cable cover on to the Genie Ultra Micro

chassis by engaging its lugs in the corresponding holes at
the rear of the chassis and slide down firmly until you
hear it clip into place.

u An optional Kensington-style locking device can be used

to lock the cable cover in place.

1

2

3

1

2

3

1

2

Contents

Monitor stand Genie Ultra Micro chassis Cable cover
(optional) (optional)

Monitor Power Adapter Fittings (see ‘included
(optional) fittings’ below)

1

2

Under certain conditions you may need to reset the software
originally installed on your computer to factory conditions, this can
be put down to many different reasons:

u

Accidental deletion of system files.

u

Incompatible software has been installed.

u

Incompatible changes to the system settings.

At Viglen, we understand that unless you have professional
knowledge of computer systems, reinstallation can be a costly and
time-consuming affair, especially for new users. This is why we
have created the Viglen Recovery Utility System – designed to
automatically reinstall your computer software quickly and
efficiently.
Before proceeding with system recovery, please observe the
following recommended guidelines.

u

Back up all personal files to a CD or a suitable backup
device before proceeding with the recovery procedure.

u

Any subsequent software installed by the user must
therefore be manually reinstalled – Please refer to the
manuals that came with your software for installation
instructions.

u

Once initiated, all data stored on the system will be destroyed
and will therefore not be recoverable.

Using the Recovery Utility

Please read the recommended guidelines above before
continuing with the recovery procedures:

1. Shutdown your Viglen PC (if applicable) and switch off.

2. Inser t the Viglen Recovery Utility CD into the CD-ROM drive.

3. Switch your computer back on.

4. The Viglen Recovery Utility CD will now load.

5. When prompted, please type ‘factory’ and press the ‘Enter’
key to initiate system recovery.

6. A Windows style screen will now appear with two horizontal
bars showing the status of the recovery sequence. Please
wait while the procedure completes.

7. When prompted, remove the Recovery Utility CD from the
drive and press a key to restart the computer.
Windows will now start up and you will be prompted to enter
you User Information – Please refer to the Software Guide
supplied with your Viglen PC.

Your Viglen Recovery Utility CD….

WARNING

ONLY TO BE USED IF YOUR VIGLEN PC HAS BECOME
UNSTABLE OR YOU HAVE BEEN ADVISED OTHERWISE BY A
MEMBER OF VIGLEN TECHNICAL SUPPORT. ALL PERSONAL
DOCUMENTS WILL BE LOST IF THIS CD IS ACTIVATED.

Hopefully, you should never need to use this utility, but in the
unfortunate event that your system must be reinstalled, please
keep this Getting Started Guide and the Viglen Recovery Utility CD
in a safe place to help ensure a hassle-free recovery.

Viglen System Recovery Utility (Optional)

Technical Support

If you have any queries concerning the following:
1 Hardware configuration problems.
2 You wish to return your hardware for repair or

arrange a service visit (subject to contract).
3 You have installation or set up difficulties.
4 You require additional drivers.

Please call our TECHNICAL SUPPORT department on

01727 201 850

Customer Care

If you have any queries concerning the following:
1 Parts missing or damaged from your Viglen PC order.
2 Incorrect goods supplied against your Viglen PC order.
3 Any complaint with a courier or delivery in general.
4 Collection of any computers or parts.
5 You have ordered or wish to order spare parts.
6 You wish to return your Viglen PC for an upgrade.
7 You wish to know the status of any returned

Viglen PC.

8 You require information on upgrading new or old

systems.

Please call our CUSTOMER CARE department on

01727 201 810

Viglen Getting Started Guide

Genie Ultra Micro

Getting Help
at Viglen

Please read this pamphlet before switching on the Viglen PC and
store in a safe place. For further information regarding your Viglen
PC please refer to the Viglen Driver CD which Includes the BIOS,
Drivers and Manual for your motherboard.

Important

Viglen is a trademark of Viglen Ltd, Viglen Ltd is a subsidiary of Viglen Technology Ltd. Pentium 4 is a registered trademark of Intel Corporation. Viglen Ltd disclaims any proprietary interest in trademarks and
trade names other than its own. Viglen cannot be liable for pictorial or typographical errors. Viglen reserve the right to change the specification of the servers without prior notification. Specifications may be
subject to change without notice. Although Viglen endeavours to ensure the accuracy of this information, Viglen will not be liable for any damages whatsoever for errors or omissions of fact herein. Viglen,
Contender, Genie and Dossier are registered trademarks of Viglen Ltd. Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corporation. Intel, Intel logo, Intel Inside, Intel Inside logo and
Pentium are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the United States and other countries All other trademarks are acknowledged. Subject to Viglen terms and conditions
available on request.

Viglen Limited,

VHQ,

7 Handley Page Way,

Old Parkbury Lane,

Colney Street,

St. Albans, Hertfordshire

AL2 2DQ

Corporate Sales

01727 201 830

Education Sales 01727 201 860
Public Sector Sales 01727 201 830
Schools Sales 01727 201 820

Email [e-mail]
Web www.viglen.co.uk

IT’s Personal