Page 1
Dossier D100
User’s Guide
Model: W651UI
First Edition: December 2007
Page 2
User's Guide
Page II
Specifications and information found in this guide are subject to change
without notice. Any changes therefore will be incorporated in future
editions. The manufacturer assumes no responsibility for errors or omissions
in this document.
Windows™ is the trademark of Microsoft Corporation.
Intel® is the trademark of Intel Corporation.
Bluetooth® is the trademark owned by its proprietor.
Other trademarks are properties of their respective owners.
NOTICE
TRADEMARKS
Page 3
User's Guide
Page III
The following standards are adopted throughout this guide:
Notebook in boldface (with or without capitalization) refers to the notebook
computer that you have purchased.
Boldface type is also used to highlight important information in this
document.
Whenever extra caution is called for, the information will be boxed in a dark
frame preceded by "Note:" or "Warning:".
Standards
Page 4
User's Guide
Page IV
This page is left blank intentionally.
Page 5
User’s Guide Contents
Page V
CHAPTER 1 BEFORE YOU BEGIN .......................................................................... 1
1.1 CHECKING WHAT YOU RECEIVED......................................................................... 1
1.2 EXAMINING YOUR COMPUTER .............................................................................. 2
1.3 THE TWO POWER LEDS ....................................................................................... 7
1.4 THE FIVE STATUS LEDS ....................................................................................... 8
1.5 THE POWER BUTTON ............................................................................................. 9
1.6 THE NINE SYSTEM BUTTONS............................................................................... 10
1.7 ATTENTION ON PCI EXPRESS AND MEDIA CARD SOCKETS.............................. 12
1.8 OPERATING TEMPERATURE ................................................................................. 14
1.9 THE <FN> KEY .................................................................................................... 15
1.10 THE SCROLL AREA ON TOUCH PAD ............................................................... 18
CHAPTER 2 BATTERY..............................................................................................19
2.1 BATTERY PACK.................................................................................................... 19
2.2 RECHARGING THE BATTERY PACK ..................................................................... 19
2.3 QUESTIONS AND ANSWERS ................................................................................. 20
2.4 BATTERY MAINTENANCE.................................................................................... 21
2.5 POWER CONSUMPTION......................................................................................... 21
2.6 REDUCING POWER CONSUMPTION ...................................................................... 22
2.7 REMOVING THE BATTERY PACK......................................................................... 22
CHAPTER 3 MEMORY..............................................................................................23
3.1 REMOVING MEMORY MODULE ........................................................................... 24
CHAPTER 4 MINI-PCI EXPRESS MODULE .........................................................26
4.1 REMOVING MINI-PCI EXPRESS MODULE............................................................ 26
CHAPTER 5 THE HARD DISK DRIVE....................................................................28
5.1 REMOVING THE HARD DISK DRIVE................................................................... 28
CHAPTER 6 SYSTEM OVERVIEW .........................................................................30
CONTENTS
Page 6
Contents User's Guide
Page VI
6.1 SYSTEM SPECIFICATION ..................................................................................... 30
CHAPTER 7 BIOS SETUP..........................................................................................31
7.1 CONFIGURATION SOFTWARE...................................................................................... 31
7.2 RUNNING THE SETUP UTILITY ............................................................................. 32
7.3 MAIN SETUP ........................................................................................................ 33
7.4 ADVANCED SETUP ............................................................................................... 35
7.5 SECURITY SETUP .................................................................................................. 37
7.6 BOOT SETUP ......................................................................................................... 39
7.7 EXIT SETUP........................................................................................................... 40
APPENDIX A - AGENCY REGULATORY NOTICES............................................41
Page 7
Dossier D100 User’s Guide
1
Chapter 1 Before You Begin
Please read this section before you start using your computer.
1.1 Checking What You Received
Your notebook package should contain the following items:
The Notebook.
AC Adapter.
AC Power Cord.
Driver CD Disc (Optional).
Battery Pack.
Note: You should keep the original factory carton and packing materials in case you
need to ship the unit back for servicing.
Page 8
Dossier D100 User's Guide
2
1.2 Examining Your Computer
Before you start using your computer, you need to get acquainted with your notebook's
main features and interfaces:
Panoramic View
Internal Microphone (Optional) LCD Screen
Web Cam Lens (Optional) Power Button
Web Cam LED (Optional) Keyboard
Two Speakers Fingerprint Reader (Optional)
Nine System Buttons Two Click Buttons
ODD Drive Five Status LEDs
Touch Pad
Page 9
Dossier D100 User’s Guide
3
Front View
Two Power LEDs Microphone Jack
Headphone Jack (SPDIF)
Rear View
VGA Connector Battery Pack
RJ11 Fax/Modem Connector DC-In Jack
Kensington Lock
Page 10
Dossier D100 User's Guide
4
Left View
Media Card Slot (for MMC/ SD/ MS/ MS-Pro
Cards)
RJ45 LAN Connector
Two USB Connectors Ventilation Holes
HDMI Connector (Optional) PCI Express Card Slot
Right View
USB Connector ODD Drive
Eject Button Emergency Hole
Page 11
Dossier D100 User’s Guide
5
Bottom View
Compartment Door (for Mini-PCI Express and
HDD Modules)
Compartment Door (for Memory Modules,
Heatsink, and CPU)
Ventilation Holes Battery Pack
Two Battery Latches
Note: Some external USB devices consume more power than this system unit can
provide. In this case, these USB devices have their own power cords. To make
sure this kind of USB devices can function properly, please connect these devices
to the AC source first before connecting to the system unit.
Page 12
Dossier D100 User's Guide
6
Two Types of Audio Jack
Mono Jack:
Your microphone jet should
have this type of connector
as shown here.
Stereo Jack:
Your headphone jet should
have this type of connector
as shown here.
Page 13
Dossier D100 User’s Guide
7
1.3 The Two Power LEDs
The Power LED
Below is how the LED would behave in different situations:
Off System is powered off, or in Hibernate mode.
On System is in full operation.
Blinking System is in Standby mode.
The Battery LED
Below is how the LED would behave in different situations:
Purple
Battery pack is being recharged: fast-charge or pre-charge.
Blue
Battery pack is in full power capacity.
Off
Battery pack is not under recharge.
Red Blinking
Battery pack is consuming down to 10% level.
Battery pack error.
Note: The Two Power LEDs are located near the front side of system unit. For exact
location, please refer to the Front View diagram in Chapter 1.2.
For more details on Standby and Hibernate, please refer to Power Options (of
Windows System) in the Control Panel of your Microsoft Windows operating
system.
Page 14
Dossier D100 User's Guide
8
1.4 The Five Status LEDs
The Wireless LAN LED
This LED would be lit when the Wireless LAN is powered on. For details on
how to power on and power off the Wireless LAN, please refer to Chapter 1.9
The Caps Lock LED
The LED would be lit when the keyboard is in Caps Lock mode. In this mode,
all characters you type are in uppercase.
The Num Lock LED
This LED would be lit when the keyboard is in Num Lock mode. In this mode,
the embedded numeric keypads can be used.
The ODD Access LED
This LED would be lit when system is accessing the ODD drive.
The HDD Access LED
This LED would be lit when system is accessing the HDD drive.
Note: The Five Status LEDs are located near the two click buttons. For exact location,
please refer to the Panoramic View diagram in Chapter 1.2.
Page 15
Dossier D100 User’s Guide
9
1.5 The Power Button
The Power Button
This Power Button is programmable by user. For detail on how to program this
button, please refer to the Power Options of Control Panel in Windows
System.
Note: The Power Button is located near the top left of keyboard. For exact location,
please refer to the Panoramic View diagram in Chapter 1.2.
Page 16
Dossier D100 User's Guide
10
1.6 The Nine System Buttons
Email Button
Press this button to activate the email function. If you press this button while
system is powered off or in hibernation, system would power on or resume from
hibernation first before launching into the “Windows Mail” application program.
Internet Button
Press this button to activate the internet function.
Media Player Button
Press this button to activate the media player function.
Play/Pause Button
Press this button to play or pause media playback.
Stop Button
Press this button to stop media playback.
Previous Track Button
Press this button to skip to the previous track/chapter of media playback.
Next Track Button
Press this button to skip to the next track/chapter of media playback.
Mute/Un-mute Button
Press this button to mute and un-mute audio volume.
Volume Button
Press this button to increase () and decrease () audio volume.
Page 17
Dossier D100 User’s Guide
11
Note: The Nine System Buttons are located near the top of keyboard. For exact
location, please refer to the Panoramic View diagram in Chapter 1.2.
In order for the Email Button ( ) to function properly in Windows™ Vista operating
system, first you need to perform the below one-time registration procedure:
In the driver CD disc, there is an execution program, “mail.reg”.
Start the registration process by double clicking on the “mail.reg” execution program.
Then follow the instructions to complete the process.
Reboot the system to activate the email function.
In order for the Media Player Button ( ) to function properly in Windows™ Vista
operating system, first you need to perform the below one-time registration procedure:
In the driver CD disc, there is an execution program, “WMPlayer.reg”.
Start the registration process by double clicking on the “WMPlayer.reg” execution
program. Then follow instructions to complete the process.
Reboot the system to activate “Windows Media Player” application program.
Page 18
Dossier D100 User's Guide
12
1.7 Attention On PCI Express And Media Card Sockets
Please observe below safety measures:
When PCI Express Card is not inserted into the PCI Express Card slot, make sure this
slot is covered by the “PCI Express Card slot door” as supplied together with this
notebook. The purpose of this “PCI Express Card slot door” is to prevent foreign
matters from entering into the system unit through this slot, when PCI Express Card is
not inserted. When inserting this “PCI Express Card slot door”, please make sure the
arrow is on the topside as shown above. Inserting this door upside down may cause
damage to your notebook.
The Media Card slot door is now
inserted into the system unit.
The PCI Express slot door is now
taken out from the system unit.
The Media Card slot door is
now taken out from the system
unit.
The PCI Express Card slot door is
now inserted into the system unit.
Arrow on topside of PCI Express
Card slot door.
Arrow on topside of Media Card
slot door.
Page 19
Dossier D100 User’s Guide
13
When no card (MMC/ SD/ MS/ MS-Pro Cards) is inserted into the media card slot,
make sure this card slot is covered by the “media card slot door” as supplied together
with this notebook. The purpose of this “media card slot door” is to prevent foreign
matters from entering into the system unit through this card slot, when no card is
inserted. When inserting this “media card slot door”, please make sure the arrow is on
the topside as shown above. Inserting this door upside down may cause damage to your
notebook.
Page 20
Dossier D100 User's Guide
14
1.8 Operating Temperature
Operating Temperature : 10ºC to 35ºC.
Page 21
Dossier D100 User’s Guide
15
1.9 The <Fn> Key
The <Fn> Function Key is located near the bottom-left corner of the keyboard. This key is
used together with other keys to activate certain pre-defined functions. To activate these
functions, press and hold down <Fn> together with the keys described below:
Wireless LAN Switch
Press this key combination (Fn+F2) to power on and power off the Wireless
LAN module. Powering on the Wireless LAN by pressing this key
combination (Fn+F2) does not automatically activate the Wireless LAN
function. After powering on, you need to activate the Wireless LAN function
through Windows™. The main purpose of this key combination (Fn+F2) is to
provide you a quick way to turn off the power of Wireless LAN when entering
venues like airplanes, airports, and hospitals where the usage of Wireless LAN
is prohibited or not advisable.
Sleep Switch
Press this key combination (Fn+F3) to enter sleep mode. In sleep mode, the
LCD display and selected devices would be switched off for less energy
consumption.
LCD/CRT Switch
Press this key function combination (Fn+F4) to switch between LCD only,
CRT only, and LCD/CRT simultaneously.
Bluetooth Switch
Press this key combination (Fn+F6) to power on and power off the
Bluetooth® module. Powering on the Bluetooth® by pressing this key
combination (Fn+F6) does not automatically activate the Bluetooth®
function. After powering on, you need to activate the Bluetooth® function
through Windows™. The main purpose of this key combination (Fn+F6) is to
provide you a quick way to turn off the power of Bluetooth® when entering
venues like airplanes, airports, and hospitals where the usage of Bluetooth® is
prohibited or not advisable.
Page 22
Dossier D100 User's Guide
16
Brightness Increasing
Press this key combination (Fn+F7) to increase brightness of LCD display.
Brightness Decreasing
Press this key combination (Fn+F8) to decrease the brightness of LCD
display.
Touch Pad Switch
Press this key combination (Fn+F9) to switch off and to switch on the touch
pad function. When the touch pad function is switched off, the touch pad
device still can work temporarily for three to five seconds during system
reboots into Windows™ operating system, or resumes from standby or
hibernation.
NumLock Switch
Press this key combination (Fn+ ) to activate or deactivate the embedded
numeric keypads.
Break Switch
Press this key combination (Fn+ ) to break the MS-DOS application
program you are running. Its function is the same as the industry standard
“break” key.
Print Screen Switch
Press this key combination (Fn+ ) to capture the screen image. Its
function is the same as the industry standard “Prt SC” key.
System Request Switch
Press this key combination (Fn+ ) to execute system request. Its function
is the same as the industry standard “Sys Rq” key.
Page 23
Dossier D100 User’s Guide
17
Note: The proper way to activate Wireless LAN, and Bluetooth® is as below:
1) Press this key combination (Fn+F2) to power on Wireless LAN.
2) Press this key combination (Fn+F6) to power on Bluetooth®.
3) Activate the application programs in Windows™.
The effective range of the system Bluetooth® is 10 meters.
Page 24
Dossier D100 User's Guide
18
1.10 The Scroll Area On Touch Pad
The system touch pad has a scroll area immediately to the right of the vertical bar. Design
of traditional touch pads requires end-users to push their fingertips upward or downward on
the scroll area to respectively scroll up and scroll down. Your system touch pad offers an
unique feature different from other more traditional design; whereby you can rest your
fingertips on the upper portion or lower portion of the scroll area to scroll up and scroll
down respectively.
The scroll
area
Page 25
Dossier D100 User’s Guide
19
Chapter 2 Battery
2.1 Battery Pack
Your notebook is equipped with a high-energy rechargeable Lithium Ion (Li-Ion) battery
pack. Battery life will vary depending on the product configuration, product model,
applications loaded on the product, power management settings of the product, and the
product features used by the customer. As with all batteries, the maximum capacity of this
battery will decrease with time and usage.
2.2 Recharging The Battery Pack
Your notebook supports both on-line and off-line recharge. Follow the procedure below to
recharge battery:
Make sure the battery pack is installed in the notebook.
Connect the AC adapter to the notebook and to an electrical outlet.
When a battery pack is being recharged, the battery LED (located near the front side of the
system unit) would be lit. For details on the LED, please refer to Chapter 1.3. When the
notebook is OFF, a depleted Li-Ion battery will take three hours to recharge.
Page 26
Dossier D100 User's Guide
20
2.3 Questions And Answers
Q: I can feel a mild heat next to the battery pack during recharge. Is it normal?
A: The battery will generate heat during recharging and discharging. There is a
protection circuit inside the notebook to prevent overheating. User needs not to
worry.
Q: My battery operation time is not as long as it should be. Why?
A: The battery is heat sensitive and can only be charged to its maximum if the battery
and its environmental temperature remain within 15-25C (59-77F). The more the
temperature deviates from this range during recharging, the less chance there is for
the battery to be fully charged. In order to recharge the pack to its full capacity, users
are requested to cool down the unit by unplugging the AC Adapter. Wait until it is
cooled down. Then plug in the AC Adapter to start recharging again.
Q: I did not use my spare battery for a few days. Even though it was fully recharged,
there wasn't as much power left as a newly charged one. Why?
A: The batteries will self-discharge (1% per day for Li-Ion) when they are not being
recharged. To make sure a battery pack is fully charged, recharge before use. Always
keep the battery inside the notebook and have the AC adapter connected whenever
possible.
Q: I did not use my spare battery for months. I have problem in recharging it.
A: If you happen to leave your battery pack to go through an extended period of self-
discharge, say more than three months, the battery voltage level will become too low
and needs to be Pre-Charged (to bring the battery voltage level high enough) before
it automatically (for Li-Ion only) resumes its normal Fast Charge. Pre-Charge may
take 30 minutes. Fast Charge usually takes 2~3 hours.
Page 27
Dossier D100 User’s Guide
21
2.4 Battery Maintenance
To maintain the battery pack's maximum capacity, you should occasionally let the notebook
deplete its battery power completely before recharging.
To carry out a complete depletion of the battery, disconnect the AC adapter and let your
notebook consume the remaining battery power. To speed up the depletion, use the HDD as
much as possible, and the LCD should be set as bright as possible. When the battery is
empty, wait for the notebook to cool down (especially the battery). The temperature should
be within 15-25C (59-77F). Then insert the AC adapter to recharge the battery.
2.5 Power Consumption
The Windows™ operating system has incorporated the latest state-of-the-art ACPI
(Advanced Configuration Power Interface) power management methodology. In order to
fully utilize the power of your battery packs, it would be a good idea for you to spend
sometime to acquire a basic understanding of the power management concept from your
operating system.
In Windows™ Operating Systems, you can go through Power Options of the Control
Panel according to the version of Windows™ Operating System the notebook applies.
We shall not describe them in details.
Page 28
Dossier D100 User's Guide
22
2.6 Reducing Power Consumption
Although your notebook (together with the operating system) is capable of power
conservation, there are measures you can take to reduce the power consumption:
Use the AC power whenever possible.
Lower the intensity of the LCD backlight. A very bright screen translates to higher
power usage.
Try to use the HDD to read and write files, instead of using the external USB
FDD.
Note: Whenever system is powered on or powered off, make sure the battery pack is
installed in the battery pack compartment.
2.7 Removing The Battery Pack
This battery pack can easily be removed and replaced. Make sure that the computer is
properly shutdown before changing the battery pack. If you would like to change the battery
pack while power is on, make sure this battery pack is not the only electrical source to the
system unit. Follow the steps below to remove the battery pack.
Make sure the system is properly
shutdown.
Flip the system upside down as
shown.
Push the battery latch to unlock
position as shown by #1.
Push the battery latch to unlock
position as shown by #2.
Maintain the battery latches in unlock
positions.
Remove the battery pack as shown by
#3.
To insert the battery pack, reverse the steps above.
Page 29
Dossier D100 User’s Guide
23
Chapter 3 Memory
Your notebook is equipped with a configurable memory unit. The industry standard
JEDEC DDR2 S.O.DIMM memory module sockets are available for memory upgrade to
4096MB. The table below illustrates all the possible ways system memory can be
configured.
Your notebook supports the below industry standard memory modules: PC4300 (DDR2-
533), and PC5300 (DDR2-667). If it occurs that different standards of memory module are
installed into the system (with one module in socket#1 and another in socket#2), the overall
speed would be downgraded to the lower standard of the two standards.
Total Memory Socket#1 Socket#2
256MB 0MB 256MB
256MB 256MB 0MB
512MB 0MB 512MB
512MB 256MB 256MB
512MB 512MB 0MB
768MB 256MB 512MB
768MB 512MB 256MB
1024MB 0MB 1024MB
1024MB 512MB 512MB
1024MB 1024MB 0MB
1280MB 256MB 1024MB
1280MB 1024MB 256MB
1536MB 512MB 1024MB
1536MB 1024MB 512MB
2048MB 1024MB 1024MB
4096MB 2048MB 2048MB
DDR2 S.O. DIMM Memory Module
Groove for indicating the
orientation of the module
1.25” max
Page 30
Dossier D100 User's Guide
24
3.1 Removing Memory Module
Below is the procedure on how to remove the memory module.
Make sure the system is properly
shutdown.
Flip the system upside down as
shown.
Remove the battery pack as shown in
Chapter 2.
Remove the screw as shown by #1.
Remove the compartment door as
shown by #2.
You can see two memory sockets with
one socket overlapping the other
socket.
Press the spring-locks sideways as
shown by #1.
The first memory module would pop
up as shown by #2.
Remove the first memory module as
shown by #3.
Memory
Modules
Page 31
Dossier D100 User’s Guide
25
Press the spring-locks sideways as
shown by #1.
The second memory module would
pop up as shown by #2.
Remove the second memory module
as shown by #3.
To insert the memory modules, reverse the steps above.
Page 32
Dossier D100 User's Guide
26
Chapter 4 Mini-PCI Express Module
Depending on model, your notebook may be equipped with an optional Mini-PCI Express
module. The Mini-PCI Express module supports wireless LAN function.
4.1 Removing Mini-PCI Express Module
Below is the procedure on how to remove the Mini-PCI Express module.
Make sure the system is properly
shutdown.
Flip the system upside down as shown.
Remove the battery pack as shown in
Chapter 2.
Remove the three screws as shown by
#1.
Remove the compartment door as
shown by #2.
Disconnect the two cables as shown by
#1.
Remove the two screws as shown by
#2.
The Mini-PCI Express module would
pop up as shown by #3.
Remove the Mini-PCI Express module
as shown by #4.
Note, there are different types of mini-
PCI Express module. Externally, they
look slightly different; especially on the
locations of the cable connections.
To insert the Mini-PCI Express module, reverse the steps above.
Mini-PCI Express
Module
Page 33
Dossier D100 User’s Guide
27
Note: Depend on the different types of mini-PCI Express module, some modules are
with two cables, while some modules are with three cables.
Page 34
Dossier D100 User's Guide
28
Chapter 5 The Hard Disk Drive
Your notebook is equipped with an industry standard 2.5”/9.5mm hard disk drive.
5.1 Removing The Hard Disk Drive
Below is the procedure on how to remove the hard disk drive.
Make sure the system is properly
shutdown.
Flip the system upside down as shown.
Remove the battery pack as shown in
Chapter 2.
Remove the three screws as shown by
#1.
Remove the compartment door as
shown by #2.
Remove the two screws as shown by
#3.
Pull the belt in a lateral direction to
unlock the HDD module as shown.
HDD Drive
Page 35
Dossier D100 User’s Guide
29
Tilt up the HDD module as shown by
#1.
Remove the HDD module as shown by
#2.
Remove the four screws as shown by
#1.
Remove the HDD drive as shown by
#2.
To insert the HDD drive, reverse the steps above.
Page 36
Dossier D100 User's Guide
30
Chapter 6 System overview
6.1 System Specification
CPU
Intel® Merom Processor Core™2 Duo (Santa Rosa Platform)
Intel® Celeron® Processor (Santa Rosa Platform)
TDP
35 watts
FSB
800/533MHz
North Bridge
Intel® GM965
VGA
Intel® GM965 Integration
Shared system memory (default), supports up to 256 MB
Memory
Dual DDR2-SODIM, 667 MHz, Max: 4GB (Dual Channel)
USB2.0
Integrated in ICH-8M
Media Card
Reader
Realtek RTS5158, USB 2.0,
4-in-1 (RS-MMC, MMC, miniSD, SD, MS, MS Pro)
LAN
Realtek PCI_Express 10/100 Network
KBC/EC
Winbond 83L951AGD or compatible
Audio Codec
High Definition integrated stereo sound
Speakers: Stereo, 1.5 watts
Audio Amplifier
Maxim MAX9789A
Modem
Agere 56k bps, V.92
ODD
12.7mm, PATA, CD-ROM RW/DVD-ROM combo
LCD Display
15.4" WXGA (1280x800)
HDD
9.5mm, 2.5", SATA, Capacity 80-200G, 5400/7200rpm
Bluetooth
USI BCM92045NMD (Factory Fit only)
WLAN Support
Intel Mini Express Card Wireless LAN 802.11N (4965AGN)
Intel Mini Express Card Wireless LAN 802.11a/b/g (4965AG)
Intel Mini Express Card Wireless LAN 802.11a/b/g
(3945ABG)
Pointing Device
Touch-pad (with 2 buttons & scrolling )
Security
Kensington lock
I/O Port
VGA x 1,RJ11 x 1,RJ45 x 1,Headphone out x 1 (with S/PDIF)
USB(2.0) x3, DC-in x 1, Mic-In x1
Battery Pack
6 cells/48 WH(2.2AH), 57WH(2.6AH)
Adaptor
65/90 watts, DC19V output, AC100~220V input
Dimension
355.4mmx257.7mmx 30.32-37.66 mm
Weight
2.6Kg without battery
Page 37
Dossier D100 User’s Guide
31
Chapter 7 BIOS Setup
7.1 Configuration Software
The notebook can easily be configured to suit your personal needs. The built-in
SETUP program allows you to setup various system parameters. The information is
stored in a battery-backed CMOS memory; so when the power is turned off, your
setup is retained. This Configuration Software is sometimes referred to as CMOS
Setup, BIOS Setup, or simply the SETUP.
Note: The SETUP can be activated by pressing <F2> during system boot-up.
You are requested to perform the following one-time procedure immediately after
you have upgraded/reprogrammed your BIOS:
* Press <F2> during system boot-up to get into the SETUP.
* Go to the EXIT sub-menu and choose Load Setup Defaults. Press
Enter.
* Now, you can customize the BIOS for your personal needs.
For detail on the BIOS SETUP, read on.
Note: For information on the BIOS upgrade, contact your local notebook
dealer.
Page 38
Dossier D100 User's Guide
32
7.2 Running the Setup Utility
There are five major sub-menus in the SETUP program: Main Setup, Advanced
Setup, Security Setup, Boot Setup, and Exit Setup. Details on the five major
sub-menus are described on the following pages.
Movement within the SETUP Utility
To move between the different item fields, use the cursor keys and . To move
between the five SETUP sub-menus, use the cursor keys and . To change the
value of a field, press the <> and <> keys. When you select one item, this item
will be highlighted and a brief explanation would be displayed in the Item Specific
Help box located on the right side of the screen. The followings are some of the
most commonly used keys:
Press <F1> to enter the menu of Help.
Press <F9> to enter the menu of Setup Defaults, then press Enter to
continue or press Esc to abort.
Press <F10> to enter the menu of Save And Exit. This would save
modifications you have made. Then exit.
Press Enter to execute command.
Press Esc to get to the EXIT Setup sub-menu, or to the next higher-level sub-
menu.
Note: The settings shown on the following sub-menu displays are factory
default settings.
The content of these sub-menu displays, described in the rest of this
chapter, is subject to change in the future.
Page 39
Dossier D100 User’s Guide
33
7.3 Main Setup
You will be greeted by this screen when you enter the Main Setup menu:
System Time:
Current time. Use <Tab>, <Shift-Tab>, or <Enter> keys to move around these
fields. To change the value, press <> or <> key.
System Date:
Today date. Use <Tab>, <Shift-Tab>, or <Enter> keys to move around these
fields. To change the value, press <> or <> key. Set any date from year 1981 to
2099. It will automatically keep track of leap years. The system date can also be set
from the operating system.
BIOS Version:
This is for display only. This shows the version of the BIOS.
KBC Version:
This is for display only. This shows the version of the KBC (Keyboard Controller).
CPU Type:
This is for display only. This shows the type of CPU you have in the system.
Page 40
Dossier D100 User's Guide
34
CPU Speed:
This is for display only. This shows the speed of CPU you have in the system.
Cache Ram:
This is for display only. This shows the memory of cache Ram you have in the
system.
Total Memory:
This is for display only. This shows the total memory in the system.
Slot 1 Memory:
This is for display only. This shows the slot 1 memory in the system.
Slot 2 Memory:
This is for display only. This shows the slot 2 memory in the system.
IDE Primary/Master:
Enter its submenu by pressing <Enter>. In this submenu, there are seven options:
Auto, User, Other ATAPI, IDE Removable, CD-ROM, ATAPI Removable, and
None. In general, you should choose the default value Auto to let the system to
automatically detect the type of optical drive you have in the system. If Auto fails to
recognize your optical drive, you can choose the User option; then enter the
parameters according to the specifications of your optical drive.
SATA Port:
Enter its submenu by pressing <Enter>. In this submenu, there are seven options:
Auto, User, Other ATAPI, IDE Removable, CD-ROM, ATAPI Removable, and
None. In general, you should choose the default value Auto to let the system to
automatically detect the type of HDD you have in the system. If Auto fails to
recognize your HDD, you can choose the User option; then enter the parameters
according to the specifications of your HDD.
Page 41
Dossier D100 User’s Guide
35
7.4 Advanced Setup
You will be greeted by this screen when you enter the Advanced Setup menu:
Summary Screen:
There are two options to this field: Enabled, and Disabled. This field allows the
system to display (enabled) or hide (disabled) the system configuration during
system boot-up.
Legacy USB Support:
There are two options to this field: Enabled, and Disabled. This field allows you to
activate (enabled) or deactivate (disabled) the legacy USB support.
Internal WLAN Power State:
There are three options to this field: On, Off, and Restore.
If set to On, the wireless LAN LED would be on after system boot-up or resume
from hibernation.
If set to Off, the wireless LAN LED would be off after system boot-up or resume
from hibernation.
If set to Restore, the wireless LAN LED would keep their last state after system
boot-up or resume from hibernation.
Page 42
Dossier D100 User's Guide
36
Internal Bluetooth Power State:
There are three options to this field: On, Off, and Restore.
If set to On, the bluetooth LED would be on after system boot-up or resume
from hibernation.
If set to Off, the bluetooth LED would be off after system boot-up or resume
from hibernation.
If set to Restore, the bluetooth LED would keep their last state after system
boot-up or resume from hibernation.
AC Wake On LAN:
There are two options to this field: Enabled, and Disabled. This field allows the
system to activate (enabled) or deactivate (disabled) the LAN function when AC
adapter is plugged into the system unit.
Page 43
Dossier D100 User’s Guide
37
7.5 Security Setup
You will be greeted by this screen when you enter the Security Setup menu:
Supervisor Password Is:
This is for display only. This shows the system’s supervisor password has been set
(Set) or not (Clear).
User Password Is:
This is for display only. This shows the system’s user password has been set (Set)
or not (Clear).
Set Supervisor Password:
Press <Enter> to get into its sub-menu. In this sub-menu (not shown here), you can
set system Supervisor Password. The Supervisor Password controls the access
to system boot-up, the access to BIOS setup, and all settings within the BIOS
setup.
Set User Password:
Press <Enter> to get into its sub-menu. In this sub-menu (not shown here), you can
set system User Password. The User Password controls the access to system
boot-up, and the access to BIOS setup.
Page 44
Dossier D100 User's Guide
38
Password On Boot:
There are two options to this field: Enabled and Disabled. If the option is set to
Enabled and when Supervisor Password and/or User Password have been set,
system would prompt for password during system boot up. In order to access the
system, you need to enter either the Supervisor Password or User Password. In
order to set this field (Password On Boot), you need to set either/both the
Supervisor Password and User Password as described above.
HDD Password:
This is for display only. This shows the system’s HDD password has been set (Set)
or not (Clear).
HDD Password:
Press <Enter> to get into its sub-menu. In this sub-menu (not shown here), you can
set system HDD Password. The sole purpose of this HDD password is to guard
against information theft namely installing this HDD into another system unit.
Therefore, system would not prompt for this password if this password is set and
the HDD is resided in the same system unit where the password was set. However,
system would prompt for this password if this password is set and the HDD is
resided in some other system than the system unit where the password was set.
Warning: You are requested to disable the HDD Password before
upgrading BIOS. Otherwise, there is a possibility that all
data in the HDD will be lost.
Page 45
Dossier D100 User’s Guide
39
7.6 Boot Setup
You will be greeted by this screen when you enter the Boot Setup Menu:
This menu is for determining the priority of which the system would boot from. This
version of BIOS supports the following boot devices: 1: IDE CD, 2: SATA HDD, 3:
USB CD-ROM, 4: USB Key, 5: USB HDD, 6: USB FDC, and 7: Boot to LAN. Use
<> and <> to select the device to work on. Then use <> and <> to escalate or
downgrade the boot priority of the selected device.
Page 46
Dossier D100 User's Guide
40
7.7 Exit Setup
You will be greeted by this screen when you enter the Exit Setup Menu:
Exit Saving Changes:
Save the changes that you have just made, and then exit the SETUP.
Exit Discarding Changes:
If you do not want to save the changes you have just made, choose this to reject all
the changes and exit the SETUP.
Load Setup Defaults:
If you are not sure how to setup certain fields, choose this. The system would get
the default settings for you.
Discard Changes:
If you do not want to keep the changes you have just made, choose this. The
system would load the previously saved settings for you.
Save Changes:
Save the changes you have just made.
Page 47
Dossier D100 User’s Guide
41
Appendix A - Agency Regulatory Notices
A.1 Safety Instructions
CAUTION: Please read these safety instructions carefully.
CAUTION: Please keep this User's Manual for future reference.
CAUTION: Please disconnect this equipment from AC outlet before
cleaning. DO NOT use liquid or sprayed detergent for cleaning. Use a clean
moistened cloth.
CAUTION: The wall socket used should be positioned near the equipment
and should be easily accessible.
CAUTION: Please keep this equipment free from humidity.
CAUTION: Place the equipment on a reliable surface at all times. A drop or
fall can cause severe damage.
WARNING: The openings of the enclosure are for air ventilation and are
meant to protect the equipment from overheating. DO NOT COVER THE
VENTILATION OPENINGS.
Page 48
Dossier D100 User's Guide
42
CAUTION: Verify the voltage of the power source before connecting the
unit to any power outlet.
WARNING: DO NOT step on or place anything over the power cord.
CAUTION: All cautions and warnings on the equipment should be noted.
WARNING: If the equipment is not used for a long period of time,
disconnect the equipment from the power source to avoid damage from power
spikes.
WARNING: NEVER pour any liquid into any openings; a fire or electrical
shock is possible.
WARNING: For safety reasons, other than pre-designated ports, doors, and
the equipment should be opened only through qualified service personnel.
CAUTION: If one of the following situations should arise, the equipment
should be checked by an authorized technician:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to excessive moisture.
d. The equipment does not work well, or you fail to get it to work
according to user's manual.
e. The equipment has been dropped or damaged.
f. The equipment has obvious signs of breakage.
Page 49
Dossier D100 User’s Guide
43
CAUTION: DO NOT LEAVE THE EQUIPMENT IN TEMPERATURES
BELOW -20ºC(-4ºF) OR ABOVE 60ºC(140ºF). IT MAY CAUSE
DAMAGE TO THE EQUIPMENT.
WARNING: Never install modem/telephone wiring during a lightning storm.
WARNING: Never install modem/telephone jacks in wet locations unless the
jack is specially designed for wet locations.
WARNING: Never touch un-insulated modem/telephone wires or terminals
unless the modem/telephone line has been disconnected at the network interface.
CAUTION: Use caution when installing or modifying modem/telephone
lines.
WARNING: Avoid using a modem/telephone (other than a cordless type)
during an electrical storm. There may be a remote risk of electric shock from
lightning.
WARNING: This computer contains an internal lithium battery-powered
real-time circuit. There is a risk of explosion and injury if the battery is
incorrectly replaced or handled. Do not attempt to recharge, disassembled,
immerse in water, or dispose of it in fire. Replacement should be done through
your notebook dealer.
Page 50
Dossier D100 User's Guide
44
WARNING: THE CD-ROM/DVD-ROM IN THIS NOTEBOOK
EMPLOYS A LASER SYSTEM.
a. To ensure proper use of this product, please read the relevant
instructions carefully and retain for future reference.
b. Should the unit ever require maintenance, contact your local dealer.
c. Use of controls, adjustments or the performance of procedures other than
those specified may result in hazardous radiation exposure.
d. To prevent direct exposure to Laser Beam, do no try to open the
enclosure.
CAUTION: The internal CD-ROM/DVD-ROM drive is classified as a
CLASS 1 LASER PRODUCT. Label is located on the outside of the CD-
ROM/DVD-ROM drive with the following wordings:
CLASS 1 LASER PRODUCT
KLASSE 1 LASER PRODUKT
WARNING: Danger of explosion if battery is incorrectly replaced. Replace
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.
Explosionsgefahr bei unsachgemäßen Austausch der Batterie. Ersatz nur durch
denselben oder einem vom Hersteller empfohlenem ähnlichen Typ. Entsorgung
gebrauchter Batterien nach Angaben des Herstellers.
WARNING: Your notebook contains a Ni-MH or Li-Ion battery pack.
There is a risk of fire and chemical burn if the battery pack is handled
improperly. Do not disassemble, crush, puncture, short external contact, dispose
of in water or fire, or expose it to temperature higher than 60ºC.
Page 51
Dossier D100 User’s Guide
45
WARNING: Handle the battery pack very carefully. Avoid touching the
metal leads on the connector of the battery case.
CAUTION: Use only approved AC Adapter with your notebook. Using the
wrong type of AC Adapter may cause serious damage to your notebook.
CAUTION: The AC Adapter can accept a line voltage ranging from 100V to
240V and is compatible with most international power sources. If you are unsure
whether your power source is compatible, please contact the local dealer for
assistance.
CAUTION: To reduce the risk of fire, use only No. 26 AWG or larger
telecommunication line cord.
CAUTION: For continued protection against risk of fire, Replace only with
same type and rating of fuse.
CAUTION: If the computer is not sold to German area, please use only the
local recognized power supply cords that are recommended by the manufacturer.
WARNING: Don't expose your notebook to excessive heat or coldness
(frost). Don't drop, spill fluids or open the exterior of the case. This can damage
the notebook and void the warranty.
Page 52
Dossier D100 User's Guide
46
A.2 Agency Notice
Federal Communications Commission Notice
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
* Reorient or relocate the receiving antenna.
* Increase the separation between the equipment and receiver.
* Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
* Consult the dealer or an experienced radio or television technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Modifications
The FCC requires the user to be notified that any changes or modifications made to this
device that are not expressly approved by the manufacturer responsible for compliance may
void the user’s authority to operate the equipment.
Cables
Connections to this device must be made with shielded cables with metallic RFI/EMI
connector hoods to maintain compliance with FCC Rules and Regulations.
Page 53
Dossier D100 User’s Guide
47
FCC RF Radiation Exposure Statement
This transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
This equipment complies FCC RF radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with a
minimum distance of 20 centimeters between the radiator and your body.
If this device is going to be operated in 5.15 ~5.25GHz frequency range, then it is
restricted in indoor environment only.
USA and Canada Safety Requirements And Notices
The FCC with its action in ET Docket 93-62 has adopted a safety standard for human
exposure to radio frequency (RF) electromagnetic energy emitted by FCC certified
equipment. The Intel PRO/Wireless LAN MiniPCI Adapter products meet the Human
Exposure limits found in OET Bulletin 65, 2001, and ANSI/IEEE C95.1, 1992. Proper
operation of this radio according to the instructions found in this manual will result in
exposure substantially below the FCC’s recommended limits.
The following safety precautions should be observed:
Do not touch or move antenna while the unit is transmitting or receiving.
Do not hold any component containing the radio such that the antenna is very close or
touching any exposed parts of the body, especially the face or eyes, while transmitting.
Do not operate the radio or attempt to transmit data unless the antenna is connected; if
not, the radio may be damaged.
Use in specific environments:
The use of wireless devices in hazardous locations is limited by the constraints posed
by the safety directors of such environments.
The use of wireless devices on airplanes is governed by the Federal Aviation
Administration (FAA).
The use of wireless devices in hospitals is restricted to the limits set forth by each
hospital.
Antenna use:
In order to comply with FCC RF exposure limits, low gain integrated antennas should
be located at a minimum distance of 20 cm (8 inches) or more from the body of all
persons.
High-gain, wall-mount, or mast-mount antennas are designed to be professionally
installed and should be located at a minimum distance of 30 cm (12 inches) or more
from body of all persons. Please contact your professional installer, VAR, or antenna
manufacturer for proper installation requirements.
Page 54
Dossier D100 User's Guide
48
Explosive Device Proximity Warning
Warning: Do not operate a portable transmitter (such as a wireless network device) near
unshielded blasting caps or in an explosive environment unless the device has been
modified to be qualified for such use.
Use On Aircraft Caution
Caution: Regulations of the FCC and FAA prohibit airborne operation of radio-frequency
wireless devices because their signals could interfere with critical aircraft instruments.
Canadian Notice
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing
Equipment Regulations.
Avis Canadien
Cet appareil numerque de la classe B respecte toutes les exigences du Reglement sur le
materiel brouilleur du Canada.
Canada Radio Frequency Interference Requirements
This Class B digital apparatus complies with Canadian ICES-003, Issue 2, and RSS-210,
Issue 4 (Dec. 2000).
“To prevent radio interference to the licensed service, this device is intended to be operated
indoors and away from windows to provide maximum shielding. Equipment (or its transmit
antenna) that is installed outdoors is subject to licensing.”
Cet appareil numérique de la classe B est conforme à la norme NMB-003, No. 2, et CNR210, No. 4 (Dec. 2000).
“Pour empêcher que cet appareil cause du brouillage au service faisant l’objet d’une
licence, il doit être utilizé à l’intérieur et devrait être placé loin des fenêtres afin de fournir
un écran de blindage maximal. Si le matériel (ou son antenne d’émission) est installé à
l’extérieur, il doit faire l’objet d’une licence.”
Page 55
Dossier D100 User’s Guide
49
European Union Notice
Product with the CE Marking comply with the EMC Directive (89/336/EEC) and the Low
Voltage Directive (73/23/EEC) issued by the Commission of the European Community and
if this product has telecommunication functionality, the R&TTE Directive (1999/5/EC).
Compliance with these directives implies conformity to the following European Norms (in
parentheses are the equivalent international standards and regulations):
* EN55022 (CISPR 22) Electromagnetic Interference
* EN55024 (IEC61000-4-2,3,4,5,6,8,11) Electromagnetic Immunity
* EN61000-3-2 (IEC61000-3-2)-Power Line Harmonics
* EN61000-3-3 (IEC61000-3-3)-Power Line Flicker
* EN60950 (IEC60950) Product Safety
For devices with built-in wireless equipment, the following additional standards apply:
* ETSI301489-17: General Emissions for Radio Equipment
* EN60950: Safety
* ETSI300328-2: Technical Requirements for Radio Equipment
CE Caution: Due to the fact that the frequencies used by 802.11b/802.11g wireless
LAN devices may not yet be harmonized in all countries, 802.11b/802.11g products are
designed for use only in specific countries or regions, and are not allowed to be operated in
countries or regions other than those of designated use. As a user of these products, you are
responsible for ensuring that the products are used only in the countries or regions for which
they were intended and for verifying that they are configured with the correct selection of
frequency and channel for the country or region of use. And deviation from permissible
settings and restrictions in the country or region of use could be an infringement of local law
and may be punished as such.
Page 56
Dossier D100 User's Guide
50
The wireless LAN device can currently be used indoors only in the following departments
of mainland France.
01 Ain 36 Indre 69 Rhône
02 Aisne 37 Indre et Loire 70 Haute Saône
03 Allier 39 Jura 71 Saône et Loire
05 Hautes Alpes 41 Loir et Cher 72 Sarthe
08 Ardennes 42 Loire 75 Paris
09 Ariège 45 Loiret 77 Seine et Marne
10 Aube 50 Manche 78 Yvelines
11 Aude 54 Meurthe et Moselle 79 Deux Sèvres
12 Aveyron 55 Meuse 82 Tarn et Garonne
16 Charente 57 Moselle 84 Vaucluse
19 Corrèze 58 Nièvre 86 Vienne
2A Corse Sud 59 Nord 88 Vosges
2B Haute Corse 60 Oise 89 Yonne
21 Côte d’Or 61 Orne 90 Territoire de Belfort
24 Dordogne 63 Puy du Dôme 91 Essonne
25 Doubs 64 Pyrénées Atlantique 92 Hauts de Seine
26 Drôme 65 Haute Pyrénées 93 Seine St Denis
27 Eure 66 Pyrénées Orientales 94 Val de Marne
32 Gers 67 Bas Rhin
35 Ille et Vilaine 68 Haut Rhin
The wireless LAN device cannot currently be used in any departments of mainland France
other than those listed above.
Maximum allowable EIRP 802.11b wireless LAN cards in the mainland departments of
France not shown in the table above are as follows: (See the ART website at www.arttelecom.fr for information on the French overseas territories.)
Frequency Ranges (MHz) Indoors Outdoors
2400 – 2446.5 10 mW Not permitted
2446.5 – 2483.5 100 mW 100 mW on private property
with Ministry of Defense
approval
Japanese Notice
Page 57
Dossier D100 User’s Guide
51
DGT Statement
U.S. Regulations Governing the Use of Modems
This equipment complies with Part 68 of the FCC Rules. On this equipment is a label that
contains, among other information, the FCC registration number and Ringer Equivalence
Number (REN) for this equipment. You must, upon request, provide this information to
your telephone company.
If your telephone equipment harms the telephone network, the Telephone Company may
discontinue your service temporarily. If possible, they will notify in advance. But, if
advance notice is not practical, you will be notified as soon as possible. You will be
informed of your right to file a compliant with the FCC.
Your telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect proper operation of your equipment. If they do, you will be
notified in advance to give you an opportunity to maintain uninterrupted telephone service.
The FCC prohibits this equipment to be connected to party lines or coin-telephone service.
In the event that this equipment should fail to operate properly, disconnect the equipment
from the phone line to determine if it is causing the problem. If the problem is with the
equipment, discontinue use and contact your dealer or vendor.
The FCC also requires the transmitter of a FAX transmission be properly identified (per
FCC Rules Part 68, Sec 68.381 (C) (3)).
Page 58
Dossier D100 User's Guide
52
Japanese Modem Notice
U.K. Modem Compliance Information
This modem is approved by the secretary of state at the Department of Trade and Industry
for connection to a single exchange line of the public switched telephone network run by
certain licensed public telecommunication operators or system connected there to (Direct
exchange lines only, not shared service or 1-1 carrier systems).
This modem is also suitable for connection to Private Automatic Branch Exchange (PABX),
which return secondary proceeding indication.
If this modem is to be used with a PBX which has extension wiring owned by BT,
connection of the modem the PBX can only be carried out by BT; or by the authorized
maintainer of the PBX unless the authorized maintainer has been given 14 days written
notice that the connection is to be made by another person; and that period of notification
has expired.
This modem is suitable for use only on telephone lines proved with Loop Disconnect or
Multi-Frequency Dialing Facilities.
Users of this modem are advised that the approval is for connection to the PSTN via the
telephone line interface supplied with it. Connection of a modem to the PSTN by any other
means will invalidate the approval.
There is no guarantee of correct working in all circumstances. Any difficulties should be
referred to your supplier.
Some network operators require that intended users of their network request permission to
connect and for the installation of an appropriate socket.
The Ringer Equivalence Number (REN) of this modem is 1. REN is guide to the maximum
number of apparatus that can simultaneously be connected to one telephone line. The REN
value of each apparatus is added together, and should not exceed 4. Unless otherwise
marked, a telephone is assumed to have a REN of 1.
This modem is only approved for use of the following facilities:
Page 59
Dossier D100 User’s Guide
53
* Storage of telephone numbers for retrieval by a predator mined code.
* Initial proceed indication detection.
* Automatic calling / automatic answering.
* Tone detection.
* Loud-speaking facility.
This modem is not approved for connection to U.K./private speech-band services. This
modem does not support an automatic re-dial function. Any other usage will invalidate the
approval of your modem, if as a result, it then ceases to confirm to the standards against
which approval was granted. The approval of this modem is invalidated if the apparatus is
subject to modification in any material way not authorized by the BABT or if it is used
with, or connected to external software that have not been formally accepted by BABT.
Loading...