ViewZ VZ-DC24-320 User Manual

Download

Page 1

VZ-DC24-320

ViewZ DC-24-30 Power Supply

VZ-DC24-320 Field Wiring and Mounting Instructions

Page 2

Contents

VZ-DC24-320 Power Supply

Installaon Tools 3 Warning Statements 3 Mounng 4 Wiring Warranty

.....................................................................................................................................................................................................

............................................................................................................................................................................................

...............................................................................................................................................................................................................

5 6

2 Installation InstructionsVisit the ViewZ USA website at http://www.viewzusa.com

Page 3

VZ-DC24-320 Power Supply

Field Wiring and Mounting Instructions

The following tools may be required depending on your installaon.

Electronic Stud Finder

Pencil Portable Drill Drill Bit

Protecve Eye-wear

Screwdriver

Level

UL Installation Requirements

Minimum screw size - 2 1/4" length, 0.117" (11/64) thread diameter, 0.4" head diameter Wire - 14AWG ~ 18 AWG with temperature tolerance of 105c

Warning Statements

PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND COMPLETELY UNDERSTOOD. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.

It is recommended that a maximum of ⅝˝ plaster board be used when mounng to wooden studs.

Be aware of the mounng environment. If drilling and/or cung into the mounng surface, always make sure that there are no electrical wires in wall. Cung or drilling into an electrical line may cause serious personal injury.

Make sure there are no water or natural gas lines inside the wall where the mount is to be located. Cung or drilling into a water or gas line may cause severe property damage or personal injury.

Wiring and Mounng of Power Supply must be done by a trained and authorized service technician.

Power Supply should be mounted on wall with a at service in an area designated for authorized personnel only.

Do not apply power to unit unl mounng and all connecons are made.

Do not install near water, high moisture, open ames or sources of high levels of heat.

Power output cabling must be housed within a cable tray, conduit, or plenum area for connuous protecon to the cabling.

Only use copper wire for output cabling. The type of wire and its rated Ampacity are determined using NEC ANSI/NFPA 70 Arcle 310.

The wire’s rated Ampacity for output cabling must be derated by mulplying by 0.8 as specied in ANSI/NFPA Arcle 645.5A.

Always crimp a UL listed ring terminal to each wire according to the ring terminal manufacturer’s instrucons.

It is recommended that a maximum of ⅝˝ plaster board be used when mounng to wooden studs.

Contact ViewZ with any quesons: (888) 998-4399

techsupport@viewzusa.com

3Installation Instructions Visit the ViewZ USA website at http://www.viewzusa.com

Page 4

Mounting

Use #12 Screws or Bolts that are at least 1.25” in length

VZ-DC24-320 Power Supply

Drill pilot holes

Screw Bolts (Qty 4)

1. Use the hole paern provided to mark where the mounng screws will be located.

2. Drill in mounng screws ¼” away from wall. (Pilot holes might be needed).

3. If not drilling to a stud, use proper fastener/support (e.g. drywall anchor).

4. Place the Power Supply Box Keyholes over the mounng screws.

5. Secure the Power Supply by ghtening screws.

If mounng to wall studs or ceiling studs, make sure that the mounng screws are anchored into the center of the wall studs or ceiling studs. Use of an edge-to-edge stud nder is recommended.

4 Installation InstructionsVisit the ViewZ USA website at http://www.viewzusa.com

Page 5

VZ-DC24-320 Power Supply

Wiring

*Use 18AWG Copper Wire or larger for output power

Diagram of Power Supply Connections

+V ADJ.

Voltage Adjustment ~24V DC to 27V DC

Clockwise to increase Voltage

Voltage Output (Posive, +)

Voltage Output (Negave, -)

Line In (Neutral)

Line In (Load)

Ground

+V ADJ.

-V

LED

ADJ .

1. Connect wires from monitor to the terminal blocks (V+) and (V-) using a Phillips screwdriver. To avoid damaging the monitor, use correct polarity.

2. Once unit is powered, the amount of output voltage can be adjusted (+V ADJ), if needed for longer cable runs that have resulted in a voltage drop.

5Installation Instructions Visit the ViewZ USA website at http://www.viewzusa.com

Page 6

VZ-DC24-320 Power Supply

Warranty

ViewZ USA

LIMITED 2 YEAR WARRANTY

What and Who is Covered by this Limited Warranty and for How Long

ViewZ USA warrants this product to be free from defects in material and workmanship for 2 YEAR of the original owner of this product. The limited warranty is valid only for the original purchaser of the product.

What ViewZ USA Will Do

At the sole opon of ViewZ USA, ViewZ USA will repair or replace any product or product part that is defecve. If ViewZ USA chooses to replace a defecve product or part, a replacement product or part will be shipped to you at no charge, but you must pay any labor

costs.

What is Not Covered; Limitaons

ViewZ USA DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS, PROJECTORS, OTHER PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM IMPROPER INSTALLATION, MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.

ViewZ USA DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. ViewZ USA IS NOT RESPONSIBLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.

What Customers Must Do for Limited Warranty Service

If you discover a problem that you think may be covered by the warranty you MUST REPORT it in wring to the address below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer purchaser must accompany all warranty claims. Warranty claims must also include a descripon of the problem, the purchaser’s name, address, and telephone number. General inquiries can be addressed to ViewZ USA Customer Service at 1-888-998-4399. Warranty claims will not be accepted over the phone or by fax.

ViewZ USA

An: Warranty Claim 177 W. Orangethorpe Ave. Placena, CA 92870

How State Law Applies

THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

Disclaimer

ViewZ USA intends to make this manual accurate and complete. However, ViewZ USA makes no claim that the informaon contained herein covers all details, condions or variaons, nor does it provide for every possible conngency in connecon with the installaon or use of this monitor. The informaon contained in this document is subject to change without noce or obligaon of any kind. ViewZ USA makes no representaon of warranty, expressed or implied, regarding the informaon contained herein. ViewZ USA assumes no responsibility for accuracy, completeness or suciency of the informaon contained in this document.

NORTH AMERICA

177 W. Orangethorpe Ave. Placena, CA 92870 USA and Canada Phone: 1-888-998-4399 Fax: 1-714-996-1138 Other Locaons

Phone: (001) 888-998-4399 Fax: (001) 714-996-1138

6 Installation InstructionsVisit the ViewZ USA website at http://www.viewzusa.com

Page 7

Print this page on Letter size Paper

Page 8