Page 1
INSTALLATION INSTRUCTIONS
Tilting Wall Mount for 42˝ to 55˝ ViewZ Monitors
Model: VZ-CMK04
NORTH AMERICA
1220 N. Kraemer Blvd.
Anaheim, CA 92806 USA
USA and Canada
Phone: 1-888-99-ViewZ
Other Locations
Phone: (001) 714-630-3380
Fax: (001) 714-630-2335
853177002922
Page 2
VZ-CMK04
Contents
Weight Limit. ............................................................................................................................................................. 2
Warning Statements. ................................................................................................................................................ 2
Installation Tools. ...................................................................................................................................................... 3
Parts List................................................................................................................................................................... 3
Mounting Hardware. ................................................................................................................................................. 4
Nylon Spacers and Flat Washers. ............................................................................................................................ 4
Features. .................................................................................................................................................................. 5
Installing the Wall Plate Introduction. ....................................................................................................................... 6
Installing the Mounting Brackets............................................................................................................................... 8
Selecting the Mounting Hardware. .............................................................................................................. 8
Griplate™ Washer Installation. .................................................................................................................... 9
Nylon Spacer Installation. ............................................................................................................................ 9
Attaching the Mounting Brackets to the Flat Panel. ................................................................................... 10
Mounting the Flat Panel.......................................................................................................................................... 10
Attaching the Flat Panel to the Wall Plate. ................................................................................................ 10
Safety Knurl Knob Installation. .................................................................................................................. 11
Locking Safety Screw Installation. ............................................................................................................. 11
Tilt Adjustment. .......................................................................................................................................... 11
Technical Specications. ........................................................................................................................................ 13
Part 2 Instructions................................................................................................................................................... 14
Part 3 Instructions................................................................................................................................................... 20
Warranty. ................................................................................................................................................................ 22
Weight Limit
THE WALL STRUCTURE MUST BE CAPABLE OF
Maximum Flat Panel Weight:
160 lbs.
SUPPORTING AT LEAST FIVE TIMES THE WEIGHT OF
THE FLAT PANEL. IF NOT, THE WALL STRUCTURE MUST
BE REINFORCED.
Warning Statements
PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION INSTRUCTIONS MUST BE READ AND
COMPLETELY UNDERSTOOD. KEEP THESE INSTALLATION INSTRUCTIONS IN AN EASILY ACCESSIBLE LOCATION
FOR FUTURE REFERENCE.
PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN MUST BE FOLLOWED, AS OUTLINED
IN THESE INSTALLATION INSTRUCTIONS. FAILURE TO DO SO COULD RESULT IN PROPERTY DAMAGE, SERIOUS
PERSONAL INJURY, OR EVEN DEATH.
SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE ASSEMBLY OF THIS PRODUCT. USE
PROPER SAFETY EQUIPMENT AND TOOLS FOR THE ASSEMBLY PROCEDURE TO PREVENT PERSONAL INJURY.
VIEWZ DOES NOT WARRANT AGAINST DAMAGE CAUSED BY THE USE OF ANY VIEWZ PRODUCT FOR PURPOSES
OTHER THAN THOSE FOR WHICH IT WAS DESIGNED OR DAMAGE CAUSED BY UNAUTHORIZED ATTACHMENTS
OR MODIFICATIONS, AND IS NOT RESPONSIBLE FOR ANY DAMAGES, CLAIMS, DEMANDS, SUITS, ACTIONS OR
CAUSES OF ACTION OF WHATEVER KIND RESULTING FROM, ARISING OUT OF OR IN ANY MANNER RELATING TO
ANY SUCH USE, ATTACHMENTS OR MODIFICATIONS.
At least two qualied people should perform the assembly procedure. Personal injury and/or property damage can result
from dropping or mishandling the at panel.
If mounting to wall studs or ceiling studs, make sure that the mounting screws are anchored into the center of the wall studs
or ceiling studs. Use of an edge-to-edge stud nder is recommended.
It is recommended that a maximum of ⅝˝ plaster board be used when mounting to wooden studs.
Be aware of the mounting environment. If drilling and/or cutting into the mounting surface, always make sure that there
are no electrical wires in wall. Cutting or drilling into an electrical line may cause serious personal injury.
Make sure there are no water or natural gas lines inside the wall where the mount is to be located. Cutting or drilling into a
water or gas line may cause severe property damage or personal injury.
This product is intended for indoor use only. Use of this product outdoors could lead to product failure and/or serious
personal injury.
Do not install near sources of high heat. Do not install on a structure that is prone to vibration, movement or chance of
impact.
Contact ViewZ with any questions:
(888) 99-ViewZ
techsupport@viewzusa.com
Page 2 Visit the ViewZ website at http://www.viewzusa.com Installation Instructions
Page 3
VZ-CMK04
Installation Tools
The following tools may be required, dependent upon your particular installation. These tools are not provided by
Viewz, but you can purchase them at your local hardware store.
Electronic Stud Finder ¼ ˝ Drill Bit
Pencil Protective Eyewear
½˝ Socket
Portable Drill
Phillips Head ScrewdriverSocket Wrench
Parts List
Your Viewz product is shipped with all proper installation hardware and components. Make sure that none of these
parts are missing and/or damaged before beginning installation. If there are parts missing and/or damaged, please stop
the installation and contact Viewz at 1-888-99-ViewZ.
VZ-CMK04 Tilting Wall Mount Assembly Components
Wall Plate
(Qty 1)
Mounting Bracket
(Qty 2)
Thread Depth Indicator
(Supplied)
Panelock™ Hardware Kit
Panelock™ Hooks (Qty 2)
Griplate™ Washer
(Qty 6)
M6 Safety Knurl Knob
(Qty 2)
Universal Spacers
(Qty 24)
M6 x 12mm Security Head
Screw (Qty 2)
5
/16˝ x 3˝ Lag Bolt
(Wooden Studs Only) (Qty 6)
5
/16˝ Flat Washer
(Qty 6)
M6 x 30mm Locking Safety
Screw (Qty 2)
Security Head
Allen Wrench
Installation Instructions Visit the ViewZ website at http://www.viewzusa.com Page 3
Page 4
Parts List (cont’d)
VZ-CMK04
Mounting Hardware
M4 x 16mm Screw
(Qty 6)
M4 x 25mm Screw
(Qty 6)
M4 x 30mm Screw
(Qty 6)
M5 x 16mm Screw
(Qty 6)
M5 x 25mm Screw
(Qty 6)
M6 x 30mm Screw
(Qty 6)
M6 x 45mm Screw
(Qty 6)
M8 x 16mm Screw
(Qty 6)
M8 x 25mm Screw
(Qty 6)
M8 x 30mm Screw
(Qty 6)
M5 x 30mm Screw
(Qty 6)
M6 x 16mm Screw
(Qty 6)
M6 x 25mm Screw
(Qty 6)
M8 x 45mm Screw
(Qty 6)
M8 x 70mm Screw
(Qty 4)
Page 4 Visit the ViewZ website at http://www.viewzusa.com Installation Instructions
Page 5
VZ-CMK04
Features
Mounting Slots
Allow for a variety of stud
congurations and
lateral adjustments when
installing the wall plate.
Cable/Electrical Cut Out
Allows for easy cable access and
power distribution installations.
Directional Mounting Arrow
Lets you know which edge is the top.
Safety Knurl Knobs
Prevent the at panel
from being removed or
dislodged from the wall
plate.
Universal Spacers
ViewZ’s uniquely
designed spacers that t
multiple
screw sizes.
Visual Centering Diamond
The visual centering diamond
will guide you in determing the
screen placement on the wall.
Mounting Rails
Allow lateral adjustments
when mounting the at panel.
Locking Safety Screws
Prevent the at panel from
being removed or dislodged
from the wall plate.
Installation Instructions Visit the ViewZ website at http://www.viewzusa.com Page 5
Page 6
Installing the Wall Plate
Introduction
Directional Mounting Arrow
The Directional Mounting Arrow stamped into the
VZ-CMK04 wall plate indicates which edge is the
top.
Visual Centering Diamond
The Visual Centering Diamond will guide you in
determing the screen placement on the wall.
Mounting Safety
Two people are recommended to install the wall
plate.
Step 1
You must secure the wall plate to two (2) wall
studs with four (4) lag bolts (2 lag bolts for each
stud found)
VZ-CMK04
X
1) Use a stud nder to determine the exact center of
wall studs in the vicinity of the wall plate.
2) Use a pencil to mark the exact center of each of the
wall studs.
Step 2
Two people are recommended for this step; one
person to level the wall plate and another person
to mark the wall stud location.
1) Place the wall plate against the wall in the desired
viewing location.
2) Adjust the wall plate to align the mount slots in the
wall plate with the center of the wall studs.
3) Level the wall plate.
4) Use a pencil to mark the upper right mounting
location along the center of the wall stud.
X
X
X
Step 3
Drill a “pilot hole” in the center of the upper right mark
using a ¼″ drill bit and power drill.
Only use a ¼˝ drill bit when drilling pilot holes.
X
X
Page 6 Visit the ViewZ website at http://www.viewzusa.com Installation Instructions
Page 7
VZ-CMK04
Installing the Wall Plate (cont’d)
Step 4
1) Place the wall plate against the wall and align it with
the pilot hole.
2) Insert one (1) 5/16˝ x 3˝ lag bolt and one (1) 5/16˝
washer into the upper right pilot hole.
3) Use a socket wrench and a ½˝ socket to tighten the
lag bolt.
Do not overtighten the lag bolt.
Step 5
1) Level the wall plate.
2) Use a pencil to mark the remaining three (3)
mounting locations along the center of each wall
stud.
Step 6
Two people are recommended for this step; one
person to level the wall plate and another person
to drill the pilot holes.
Drill a “pilot hole” in the center of each of the marks with
a power drill and a ¼″ drill bit.
Only use ¼″ drill bit when drilling the pilot holes.
Step 7
1) Insert one (1)
5
/16″ x 3″ lag bolt and one (1) 5/16″
washer into each pilot hole
2) Tighten all lag bolts using a socket wrench and ½″
socket.
Do not overtighten the lag bolts when attaching
the mount to the wall. Improper installation may
result in personal injury or property damage.
Proceed to the “Installing the Mounting Bracket” on
page 8.
Installation Instructions Visit the ViewZ website at http://www.viewzusa.com Page 7
Page 8
Installing the Mounting Brackets
Selecting the Mounting Hardware
1) Insert a small straw or toothpick into the threaded
inserts found on the back of the at panel.
2) Use a pencil to mark the depth of the threaded
insert on the small straw or toothpick.
3) Mark the straw or toothpick 1/8” above the depth of
the threaded insert, as shown in Figure 1.
4) Insert the small straw or toothpick into the remaining
threaded inserts to compare and verify their depth
using the straw or toothpick’s 1/8” allowance mark.
5) Locate the correct diameter screw for the threaded
insert.
VZ-CMK04
If the screw you selected is longer than the 1/8”
allowance mark on the small straw or toothpick,
as shown in Figure 2 and Figure 3, do not use
this screw. The screw length must not bypass the
mark.
6) Test each size of the screws provided.
The correct screws should thread easily into the
mounting point and not pull out when tension is
applied.
Proceed to the “Griplate™ Installation” section.
Small Straw
or Toothpick
Small Straw or Toothpick
Depth Plus 1/8” Allowance
Mark
Small Straw
or Toothpick
Marking the 1/8”
Allowance
Depth Plus 1/8” Allowance
Mark
Page 8 Visit the ViewZ website at http://www.viewzusa.com Installation Instructions
Page 9
VZ-CMK04
Installing the Mounting Brackets (cont’d)
Griplate™ Installation
ViewZ’s Universal Washers are designed to
accommodate the various M4, M5, M6 and M8 hole
sizes required by at panels.
Do not place excessive pressure on the back of
the at panel, as this may damage the at panel.
The Universal Washer must be installed between
the head of the mounting screw and the mounting
bracket as shown with dimples facing down.
Does the at panel have:
● Recessed mount points?
● Uneven mount points?
● A curved back?
● Any obstruction near the mount point?
If Yes, you must install Universal Spacers. Remove the
mounting brackets, Universal Washers, and mounting
screws from the back of the at panel. Proceed to the
“Universal Spacer Installation” below.
If No, skip to the “Attaching the Mounting Bracket to
the Flat Panel” on page 10.
Universal Spacer Installation
ViewZ’s Universal Spacers allow you to attach the
mounting bracket to at panels which have recessed or
uneven mount points. Each Universal Spacer adds ¼˝
to the distance between the mounting bracket and the
at panel.
The Universal Spacers must be stacked and
oriented as shown.
M8
M5, M6
M4
Mounting Screw
Universal Washer
Mounting Bracket
Flat Panel
Universal Spacer
Mount Point
The Universal Spacers must only be installed
between the mounting bracket and the at panel.
The Universal Spacers will t M4, M5, M6 and M8
screw sizes.
Proceed to the “Attaching the Mounting Bracket to
the Flat Panel” section.
1˝ ¼˝
Installation Instructions Visit the ViewZ website at http://www.viewzusa.com Page 9
Page 10
Installing the Mounting Brackets (cont’d)
Attaching the Mounting Brackets to the Flat Panel
This section presumes that you have read and
understood these sections:
● Selecting the Proper Mounting Hardware
● Universal Washer Installation
● Universal Spacer Installation
1) Place your at panel screen-side down on a soft, at
surface.
2) Identify the number and location of the thread
inserts on the back of your at panel.
3) Aligning the holes on each mounting bracket with
the thread inserts on the back of your at panel.
4) Secure each mounting bracket to your at panel by
inserting a minimum of two (2) screws per bracket.
Do not overtighten the mounting hardware.
Proceed to the “Mounting the Flat Panel” below.
VZ-CMK04
Mounting the Flat Panel
Attaching the Flat Panel to the Wall Plate
This section requires two people.
Do not release your at panel until you are certain
that top and bottom hooks of both mounting
brackets are securely seated on the upper and
lower mounting rails of the wall panel.
1) Raise the at panel past the top and bottom
mounting rails on the wall panel.
2) Slide the at panel down slowly, keeping it close to
the wall.
3) Engage the top and bottom mounting brackets to
the rails of the wall plate.
Page 10 Visit the ViewZ website at http://www.viewzusa.com Installation Instructions
Page 11
VZ-CMK04
Safety Knurl Knob Installation
If you chose not to install the safety knurl knobs
and instead chose to use the Panelock™, skip this
section and proceed to the Panelock™ Installation
section below.
The Panelock™ is a theft deterent device. It comes
with security hardware that requires a special tool
that is used to install and remove the security head
screws.
The safety knurl knobs keep the at panel from
being accidently dislodged from the VZ-CMK04.
1) Fully extend the at panel away from the wall.
2) Install and tighten a safety knurl knob at the top of
one of the mounting brackets.
3) Repeat steps 1 and 2 for the other safety knurl
knob.
Panelock™ Installation
Safety Knurl Knob
(1 per Bracket)
If the safety knurl knobs were previously installed,
they must be removed prior to installing the
Panelock™ hardware.
1) Slide the Panelock™ onto the top mounting rail,
placing the Panelock™ to the outside edge of the
at panel bracket.
Be sure that the Panelock™ is facing in the same
direction as shown in the illustration to the right.
2) Insert and tighten one (1) M6 x 12mm screw to
attach the Panelock™ to the at panel bracket.
Repeat and to attach the remaining
Panelock™.
Proceed to “Tilt Adjustment” on page 12.
Panelock™
Hook
M6 x 12mm
Security Head
Screw
Security Head
Wrench
Panelock™
Hook
Security Head
Wrench
Installation Instructions Visit the ViewZ website at http://www.viewzusa.com Page 11
Page 12
Locking Safety Screw Installation
The locking safety screws keep the at panel from
being accidently dislodged from the VZ-CMK04.
1) Thread an M6 x 30mm locking safety screw at the
bottom of one of the mounting brackets.
2) Use a Phillips head screwdriver to tighten the
locking safety screw.
3) Repeat steps 1 and 2 for the other locking safety
screw.
Do not overtighten the locking safety screws.
Proceed to the “Installing the Mounting Bracket”
below.
Tilt Adjustment
Adjusting the Flat Panel Friction Tilt Angle
1) Place one hand at the center top edge of the at
panel.
2) Place the other hand on the center bottom edge of
the at panel.
3) Using the upper hand, gently pull the top of the
at panel towards you while the lower hand gently
pushes the bottom of the at panel away from you.
VZ-CMK04
M6 x 30mm
Locking Safety Screw
(1 per Bracket)
Adjusting the Flat Panel to the Original Position
1) Place one hand at the center top edge of the at
panel.
2) Place the other hand on the center bottom edge of
the at panel.
3) Using the upper hand, gently push the top of the at
panel towards the wall while the lower hand gently
pulls the bottom of the at panel away from the wall.
Page 12 Visit the ViewZ website at http://www.viewzusa.com Installation Instructions
Page 13
VZ-CMK04
Technical Specications
All measurements are in inches [millimeters].
Installation Instructions Visit the ViewZ website at http://www.viewzusa.com Page 13
Page 14
INSTALLATION INSTRUCTIONS
VZ-CMK04 PART 2
Ceiling Mount Adapter
Page 15
VZ-CMK04
Installation Tools
The following tools may be required depending upon your particular installation. They are not included.
2
1
Tape Measure
Power Drill
Pencil Protective Eyewear
Phillips Tip Screwdriver
Ladder
Socket Wrench
Parts List
Make sure your Viewz product has the following hardware and components before beginning installation. If there are
parts missing and/or damaged, stop the installation and call ViewZ at (888) 99-ViewZ.
VZ-CMK-P2 Hardware
M10 Nut
(Qty 4)
M10 Flat Washers
(Qty 8)
Ceiling Adapter
(Qty 1)
M10 Hex Head Bolt
(Qty 4)
Installation Instructions Visit the ViewZ website at http://www.viewzusa.com Page 15
Page 16
VZ-CMK04
Installing the VZ-CMK-P2 Adapter
Attaching The Ceiling Adapter
Step 1
Before the following steps are begun, the appropriate suspension device must be installed. ViewZ offers the
VZ-CMK-P3 or a standard 1-1/2” NPT extension pipe. Please see the installation instructions that are included
with these respective mounting congurations.
In addition, some steps of this installation may require two people to prevent personal injury and/or damage to
your projector. Please observe all warnings in the following installation procedure and utilize proper safety
equipment at all times.
1) To attach the ceiling adapter to the suspension device (not included), rotate the ceiling adapter onto the
suspension device ve (5) complete turns.
VZ-CMK-P2
Page 16 Visit the ViewZ website at http://www.viewzusa.com Installation Instructions
Page 17
VZ-CMK04
Step 2
A Phillips head screwdriver is required to perform the following step.
1) Once the ceiling adapter has been attached, tighten the M6 x 12mm Phillips head set screw using a Phillips
screwdriver.
VZ-CMK-P2
Installation Instructions Visit the ViewZ website at http://www.viewzusa.com Page 17
Page 18
VZ-CMK04
Attaching the Mounting Plate
Step 1
1) Use four M10 hex head bolts, eight M10 at washers, and four M10 nuts to attach the mounting plate to the ceiling
adapter.
At this time, nger tighten all hardware.
*Mount shown for illustration purposes only (not included)
Step 2
A 17mm open-end wrench and a 17mm socket wrench will be required to perform the following step
(not included).
1) Once the two units have been attached together, use a 17mm socket wrench and a 17mm wrench to tighten the
M10 hardware.
*Mount shown for illustration purposes only (not included)
Page 18 Visit the ViewZ website at http://www.viewzusa.com Installation Instructions
Page 19
VZ-CMK04
Technical Specications
All measurements are in inches [mm].
Installation Instructions Visit the ViewZ website at http://www.viewzusa.com Page 19
Page 20
Part 3 Installation Instructions
Introduction
This 1.5 in. adjustable-height suspension adapter allows
the height of the display or projector to be adjusted
within a range of 24 - 46 in.
(60.96-116.84cm) in 1.25 in. (3.18cm) increments.
Installing the VZ-CMK-P3
Are you attaching the VZ-CMK-P3 to a single stud
or a concrete surface?
If a single stud, continue to the “Single Stud”
section below.
If a concrete surface, go to the “Solid Ceiling
Surface” section on page 2.
The ceiling should be capable of supporting at least ve
(5) times the weight of the product that will be used with
this accessory. If the surface cannot support this weight,
it must be reinforced. Proper installation procedure
by qualied personnel as outlined in the installation
instructions must be adhered to. Failure to do so could
result in serious personal injury.
VZ-CMK04
Solid Ceiling Surface Installation
Use suitable, commercially available hardware to
secure the VZ-CMK-P3 to the ceiling surface using the
four corner mounting holes.
Single Stud Installation
Use suitable, commercially available hardware to secure
the VZ-CMK-P3 to the stud using the two mounting
slots.
Height Adjustment
Make sure to hold the at
panel, or projector, securely
and remove it from the
mount to make the height
adjustment prior to loosening
the adjustment screws.
Loosen, remove, adjust then
re-tighten the screws. Failure
to do so could result in injury
and or damage to the at
panel or projector.
1) Remove the adjustments
screws to adjust the height.
2) Re-insert adjustment screws
into holes once pipe is at the
desired length.
Page 20 Visit the ViewZ website at http://www.viewzusa.com Installation Instructions
Page 21
VZ-CMK04
Technical Specications
All measurements are in inches [mm].
.28
7.1
4.50
114.3
6.72
170.7
4.50
114.3
4.50
114.3
Ø. 41
10.3
1.5" NPT
PIPE THREADS
ADJUSTABLE
1.00
25.4
27.0
685.5
(CABLE ACCESS)
1.06
26.9
2.50
63.5
44.0
1117.3
Installation Instructions Visit the ViewZ website at http://www.viewzusa.com Page 21
Page 22
VZ-CMK04
Warranty
Warranty
VIEWZ
LIMITED LIFETIME WARRANTY
What and Who is Covered by this Limited Warranty and for How Long
Viewz warrants this product to be free from defects in material and workmanship for the lifetime of the original owner of
this product. The limited warranty is valid only for the original purchaser of the product.
What ViewZ Will Do
At the sole option of ViewZ, ViewZ will repair or replace any product or product part that is defective. If ViewZ chooses
to replace a defective product or part, a replacement product or part will be shipped to you at no charge, but you must
pay any labor costs.
What is Not Covered; Limitations
VIEWZ DISCLAIMS ANY LIABILITY FOR DAMAGE TO MOUNTS, ADAPTERS, DISPLAYS, PROJECTORS, OTHER
PROPERTY, OR PERSONAL INJURY RESULTING, IN WHOLE OR IN PART, FROM IMPROPER INSTALLATION,
MODIFICATION, USE OR MISUSE OF ITS PRODUCTS.
VIEWZ DISCLAIMS ALL OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. VIEWZ IS NOT RESPONSIBLE FOR
INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING BUT NOT LIMITED TO, INABILITY TO USE ITS
PRODUCTS OR LABOR COSTS FOR REMOVING AND REPLACING DEFECTIVE PRODUCTS OR PARTS. SOME
STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES,
SO THE ABOVE LIMITATION OR EXCLUSION MAY NOT APPLY TO YOU.
What Customers Must Do for Limited Warranty Service
If you discover a problem that you think may be covered by the warranty you MUST REPORT it in writing to the address
below within thirty (30) days. Proof of purchase (an original sales receipt) from the original consumer purchaser must
accompany all warranty claims. Warranty claims must also include a description of the problem, the purchaser’s name,
address, and telephone number. General inquiries can be addressed to ViewZ Customer Service at 1-888-99-ViewZ.
Warranty claims will not be accepted over the phone or by fax.
ViewZ
Attn: Warranty Claim
1220 N. Kraemer Blvd.
Anaheim, CA 92806
How State Law Applies
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY ALSO HAVE OTHER RIGHTS WHICH
VARY FROM STATE TO STATE.
Disclaimer
ViewZ intends to make this manual accurate and complete. However, ViewZ makes no claim that the information
contained herein covers all details, conditions or variations, nor does it provide for every possible contingency in
connection with the installation or use of this product. The information contained in this document is subject to change
without notice or obligation of any kind. ViewZ makes no representation of warranty, expressed or implied, regarding
the information contained herein. ViewZ assumes no responsibility for accuracy, completeness or sufciency of the
information contained in this document.
©ViewZ 2011
Page 22 Visit the ViewZ website at http://www.viewzusa.com Installation Instructions
Loading...