ViewZ vz19rtt User Manual

19-INCH PREMIUM

TOUCH SCREEN CCTV MONITOR

USER MANUAL

Please read this manual thoroughly before use, and keep it handy for future reference.

SAFETY INSTRUCTION ………………………………………………………….……

2 ~ 3

CAUTIONS ……………………………………………………………..........................

4

FCC RF INTERFERENCE STATEMENT …………………………….......................

5

CONNECTING WITH EXTERNAL EQUIPMENT ……………………………………

6

REMOTE FUNCTIONS …………………………………………………………………

7

CONTROLS AND FUNCTIONS ………………………………………………………..

8 ~ 15

MOUNTING GUIDE ……………………………………………………………………..

16

D-SUB CONNECTOR PIN ASSIGNMENTS …………………………………………

17

POWER MANAGEMENT ………………………………………………………………

18

SPECIFICATION ………………………………………………………………………

19 ~ 20

TROUBLE SHOOTING GUIDE ………………………………………………….........

21

- 1 -

This Monitor was
Manufactured by ISO 9001
Certified Factory

Important Safety Instruction

1. Read these instructions.

2. Keep these Instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s
instructions.

8. Do not install near any heat sources such as radiators, heat registers,stoves, or other
apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.

Apolarized plug has two blades with one wider than the other.
Agrounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the bsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles and the point where they exit from the apparatus.

11. Only use attachment/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket or table specified by the manufacturer or
sold with the apparatus. When a cart is used, use caution when moving
the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused

for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus
has been damaged in any way, such as power-supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the apparatus the apparatus has been exposed to
rain or moisture does not operate normally or has been dropped.

- 2 -

- The apparatus shall not be exposed to dripping or splashing and that no objects filled with liquids,
such as vases, shall be placed no the apparatus.

14 Minimum distances(e.g. 10cm) around the apparatus for sufficient ventilation.

“WARNING – To reduce the risk of fire or electric shock, do not expose the apparatus to rain or moisture.”

“The apparatus shall not be exposed to dripping or splashing and no objects filled with liquids,

such as vases, shall be placed on the apparatus.”

This symbol is intended to alert the user to the presence of uninsulated:

dangerous voltage with in the product’s enclosure that may be of sufficient

magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating
and maintenance(servicing) instructions in the literature accompanying the
appliance.

- 3 -

CAUTION

The power supply cord is used as the main disconnect device, ensure that the socket-outlet is
located/installed near the equipment and is easily accessible.

ATTENTIONN

Le cordon d`alimentation est utillsé comme interrupteur général. La prise de courant doit être
située ou installée à proximité du matériel et être facile d`accès

▶ NEVER REMOVE THE BACK COVER

Removal of the back cover should be carried out only by qualified personnel.

▶ DO NOT USE IN HOSTILE ENVIRONMENTS

To prevent shock or fire hazard, do not expose the unit to rain or moisture.
This unit is designed to be used in the office or home. Do not subject the unit to vibrations,
dust of corrosive gases.

▶ KEEP IN A WELL VENTILATED PLACE

Ventilation holes are provided on the cabinet to prevent the temperature from rising.
Do not cover the unit or place anything on the top of unit.

▶ AVOID HEAT

Avoid placing the unit in direct sunshine or near a heating appliance.

▶ TO ELIMINATE EYE FATIGUE

Do not use the unit against a bright back ground and where sunlight or other light sources will
shine directly on the monitor.

▶ BE CAREFUL OF HEAVY OBJECT

Neither the monitor itself nor any other heavy object should rest on the power cord.
Damage to a power cord can cause fire or electrical shock.

- 4 -

NOTE

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures.

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.

- Consult the dealer or an experienced radio, TV technician for help.

- Only shielded interface cable should be used.

Finally, any changes or modifications to the equipment by the user not expressly approved by
the grantee or manufacturer could void the users authority to operate such equipment.

▶ DOC COMPLIANCE NOTICE
This digital apparatus does not exceed the Class A limits for radio noise emissions from digital
apparatus set out in the radio interference regulation of Canadian Department of
communications.

- 5 -

A. BOTTOM PANEL CONTROL

1. HDMI2 IN

2. HDMI1 IN

3. DVI IN

4. VGA(D-SUB) IN

5. PC STEREO IN

6. AUDIO OUT(Speaker)

7. COMPONENT Y,Pb,Pr & SOUND L,R IN

8. DC 12V IN

9. TRIGGER IN

B. SIDE PANEL CONTROL

1. VIDEO1(AV1) IN

2. VIDEO1(AV1) OUT

3. VIDEO2(AV2) IN

4. VIDEO2(AV2) OUT

5. S-VIDEO(Y/C) IN

6. S-VIDEO(Y/C) OUT

7. AV1 & S-VIDEO AUDIO IN

8. AV1 & S-VIDEO AUDIO OUT

9. AV2 AUDIO IN

10. AV2 AUDIO OUT

11. TOUCH SCREEN USB CABLE

12. DC 12V ADAPTOR

- 6 -

2 3 4 5 6 7 8 9 1

C. REMOTE CONTROLLER (Option)

1. POWER( )

Turns the power ON or OFF. There will be a few seconds delay before the display appears.

2. SOURCE

Selects PC or video(AV1/AV2/S-Video/Component/HDMI/DVI/PC) sources.

3. AUTO

Auto geometry adjustment in PC Source.

4. HOLD

Stops the Trigger & Auto switching functions.

5. MUTE

Mutes the sound.

6. MENU

Activates and exits the On Screen Display.

7. EXIT

Exits the On Screen Display.

8. VOL( )

Increases or decreases the level of audio volume.

9. UP/DOWN

Moves to OSD menu.

10. SOURCE/SELECT

Accepts your selection or displays the current mode.

11. INFO

Input mode information Display.

12. STILL

Stops the picture.

13. PIP (Picture In Picture)

Activates PIP mode.

14. P.INPUT

Changes source of sub picture in PIP mode.

15. P.POS

Moves the position of sub picture for PIP mode.

16. P.SIZE

Changes the size of sub and main picture for PIP mode.

17. SWAP

Alternates between main and sub picture.

18. ARC (Aspect Ratio Control)

Selects screen ratio.

19. APC (Auto Picture Control)

Selects picture mode.

20. ACC (Auto Color Control)

Selects Colour mode.

21. S.SET

Selects Sound mode main input or sub input

22. PC

Selects PC mode(PC, DVI & HDMI).

23. AV

Selects AV mode.(AV1, AV2 & S-VIDEO).

24. COMP

Selects COMPONENT mode.

- 7 -

D. FRONT KEY CONTROL

1 / 2. ◀ VOL ▶

Adjust the volume and menu settings.

3 / 4. ▲ / ▼

These buttons allow user to enter the sub-menu of the activated function.
The up(▲) button is HOLD function and stop the Trigger & Auto switching functions.

5. SOURCE/SELECT

Select PC or video.
Select On Screen Display menu.

6. MENU/EXIT

Activate and exit the On Screen Display.

7. POWER ON/OFF( / I )

Turns the power ON or OFF. There will be a few seconds delay before the display appears.

8. IR Sensor

Remote controller sensor.

9. POWER LED

The power LED lights with green when the power is turned ON.
The power is turned off by pressing the power switch again and the power LED goes Red.

- 8 -

OSD MENU DESCRIPTION

All picture, sound settings and setup for the monitor can be adjusted in the OSD menu.
(On Screen Display)
To adjust the OSD screen:

1. Press the Menu button to enter the OSD menu.

2. Press the ▲/▼ buttons to select the desired option. The selected option is highlighted.

3. Press the ▶ button to enter the submenu for adjusting items.

4. Change the value you wish to adjust by using the ▲/▼ buttons.

5. Press the ◀ button to exit the submenu for adjusting items.

6. Press the Menu button to exit the OSD menu.

A. Custom

Option

Function

Value

Brightness

Adjusts brightness of the screen.

0 ~ 100

Contrast

Adjusts intensity of the image.

0 ~ 100

Color

1)

Adjusts color of the picture.

0 ~ 100

Tint

2)

Adjusts tint of the picture.

0 ~ 100

Sharpness

1)

Adjusts sharpness of the picture.

0 ~ 100

1) Unavailable in RGB PC, DVI, HDMI1 and HDMI2.

2) Unavailable in Component mode and PAL system.

- 9 -

B. Picture/Sound

Option

Function

Value

Picture Mode

Sets picture mode.

See table below

Color Tone

Sets color tone.

See table below

Mute

Mutes speaker sound.

Off or On

Volume

Adjust the level of audio volume.

0 ~ 100

Size

Display picture size.

See table below

NR

1)

Reduces noise of the picture.

On or Off

3D Comb

2)

Activates the 3D comb filter.

On or Off

PC

3)

See table below.

1) Unavailable in RGB PC, DVI, HDMI1 and HDMI2.

2) Unavailable in S-Video, RGB PC, DVI, HDMI1, HDMI2 and Component.

3) Only available in RGB PC.

Picture Mode

Custom

Applies user selected values.(Brightness, Contrast, Color, Tint and Sharpness)

Dynamic

Provides enhanced contrast and sharpness.

Standard

Provides standard contrast and sharpness.

Movie

Is recommended for viewing film-based content.

Mild

Reduces contras and sharpness.

- 10 -

Color Tone

Cool

Gives the white color a bluish tint.

Normal

Gives the white color a neutral tint.

Warm

Gives the white color a reddish tint.

User

To manually adjust the color tones(Red, Green, and Blue).

Size

4:3

1)

Sets the image size to 4:3

Panorama

Sets the image to panorama

Zoom1

Expands the image size about two times to upward and downward

Zoom2

Expands the image size about one and half times to upward and downward

Wide

Sets the image size to wide

Under

Adjusts the image size to display resolution without overscan

1:1

Adjusts the image size to input resolution with overscan

1) Only available in RGB PC, HDMI1 and HDMI2.

PC

Option

Function

Value

Auto Adjust

Auto geometry adjustment.

Phase

Adjusts the number of horizontal picture elements.

0 ~ 100

H-Position

Adjusts the horizontally picture position.

0 ~ 100

V-Position

Adjusts the vertically picture position.

0 ~ 100

Frequency

Adjusts the vertical noise of screen image.

0 ~ 100

- 11 -

C. PIP

Option

Function

Value

PIP

Activates the PIP feature.

Off or On

Input Source

Selects the input source for the PIP area.

See table below

PIP Mode

Enables 3 screen size.4:3 side by corner, 4:3 side by 4: 3,
and full screen side by side.

PIP, PBP1 or PBP2
PIP Size

Selects the size of PIP screen.

Size1, Size2 or Size3

Position

Selects the position of PIP screen. Right of Bottom, Left of
Bottom, Left of Top and Right of Top.

RB, LB, LT or RT
Swap

Alternates between the main and sub picture

Sound Select

Selects the sound source from either the Main or PIP

Main or Sub

Input Source

Main

Sub

Available

combination

AV1, AV2 or S-Video

AV1, AV2 or S-Video

AV1, AV2 or S-Video

RGB PC, DVI, HDMI1, HDMI2
or Component

RGB PC, DVI, HDMI1, HDMI2
or Component

AV1, AV2 or S-Video

Unavailable
combination

RGB PC, DVI, HDMI1, HDMI2
or Component

RGB PC, DVI, HDMI1, HDMI2
or Component

- 12 -

D. Setup

Option

Function

Value

Reset

Resets the monitor settings to their
factory default.

Language

Sets the language of the OSD menu.

English, French, Deutsch,
Italian, Spanish, Portuguese
or Nederland

OSD Tone

Changes background of monitor menus.
(e.g. input source & information)

Transparency or On

Blue Screen

Displays a blue screen if the monitor
receives no signal.

Off or On

Key Lock1)

Locks all buttons of the monitor.
Note: Use remote controller to unlock.

Off or On
Trigger

See table below

Auto Switching

See table below

1) How to unlock

① On the front key: Press the SOURCE/SELECT and MENU button at the same time over 3 seconds.
② On the Remote Controller: The Remote Controller operates well because the Key Lock function is

only allowed for the front key of this product.

- 13 -

Motion Detection (Built-in PIR sensor; Passive Infra-Red)

Option

Function

Value

Trigger Enable

Activates the trigger feature.

Off or On.

Trigger Input

Selects the input source for the Trigger.

AV1, AV2, S-Video, RGB PC,
DVI, HDMI1, HDMI2 and
Component

Buzzer

Activates an audible signal when the monitor
receives an trigger signal.

On or Off.

Trigger Time

Selects the amount of time, in seconds,
that the monitor displays the trigger Input image.

3 ~ 100.
Trigger Option

Selects the type of physical trigger input.

See table below.

Display Type

Selects the mode in which the monitor displays
the Trigger Input. The monitor takes one of the
following actions:

- PIP & FULL: Displays the Trigger Input in the PIP
of the current video input source.
Note: The main video source must support the
Trigger Input source as a PIP option. See section
“Input Source” in “C. PIP”.

- FULL: Switches the display to show the Trigger
Input in the full screen.

PIP & FULL or FULL.

- 14 -

N/C(Normally Closed):
The Trigger function is activated when
the trigger cable is opened.

N/O(Normally Opened):
The Trigger function is activated when
the trigger cable is closed.

High:
The Trigger function is activated when
the trigger signal is DC 2~5[V].

Low:
The Trigger function is activated when
the trigger signal is DC 0~0.6[V].
Note: In this case, trigger port has high
status electrically, so the trigger cable
has to have ground( or earth) status to
be activated.

Auto Switching

Option

Function

Value

Auto Switching

Activates the Auto Switching feature.

Off or On

Input Enable

Opens another menu and you can select the input
sources to include in the Auto Switching cycle.

AV1, AV2, S-Video, RGB PC,
DVI, HDM1, HDMI2 and
Component

Time

Selects the amount of time, in seconds, that the
monitor displays each selected input source.

3 ~ 100

- 15 -

Wall mounting (Optional)

The LCD monitor is suitable for wall mounting by using the VESA 100 standard wall mount (not
included in the delivery).

※ Attention!

You must use four M4x10 screws to assemble this monitor and the wall mount bracket.

- 16 -

▶ PIN ASSIGNMENTS

Pin 1

RED VIDEO

9

2 GREEN VIDEO

10

SIGNAL CABLE DETECT

3

BLUE VIDEO

11

GROUND

4

GROUND

12

SDA(for DDC)

5

GROUND

13

H-SYNC.(or H+V SYNC.)

6

RED GROUND

14

V-SYNC.

7

GREEN GROUND

15

SCL(for DDC)

8

BLUE GROUND

D-SUB

▶ ACCESSORIES

1. Power cord.

2. Power adaptor (Built-in).

3. User’s manual.

4. PC cable.

5. Touch Screen Install CD.

6. Trigger cable (Option).

7. Stereo cable (Option).

8. Remote controller (Option).

9. Batteries (Option).

10. Wall mount (Option).

11. Rack mount (Option).

- 17 -

This monitor features a power management system to “power down” upon receipt of the VESA
DPMS(The display power management signaling) from a VESA DPMS video card.
The VESA DPMS-compliant video card performs this signaling system through not sending
horizontal, vertical, or sync signal.
This monitor enters an appropriate mode through identifying each of the three modes of the
signaling system.

POWER CONSUMPTION : < 50W

LED INDICATOR

The power management feature of the monitor is comprised of four stages: On(Green),
Standby, Suspend, Active off(Red on/off 1 sec) and Unsupported mode(Green).

MODE

LED COLOR

MONITOR OPERATION

ON

GREEN

Normal Operation

STANDBY

RED ON/OFF

1 SEC

Screen blanks after preset idle time
And some electronic circuits or all
Circuitry in the monitor shut down.

SUSPEND

ACTIV OFF

UNSUPPORTES

MODE

GREEN

Normal operation but the on screen
Display will show error massage

POWER OFF

RED

Not Operation

- 18 -

1. Monitor Specification

19”

LCD- Type

19˝ Diagonal AM-TFT(Active-Matrix)

Pixel pitch(mm) : 0.294(H) x 0.294(V)

BRIGHTNESS: 250cd/ m² (Typical)

CONTRAST RATIO: 800:1(Typical)

RESPONSE TIME: 5msec(Typical)

RESOLUTION (H x V)

1280X1024 @60Hz

FREQUENCY

HORIZONTAL: 31~ 64KHz, VERTICAL: 56-75Hz

INPUT SIGNAL

VIDEO (2ch input 1.0Vp-p, 75Ω terminated, loop-throughout)
S-VIDEO (1ch input (Y/C) , loop-throughout)

COMPONENT (Y,Pb,Pr, Sound L/R)

DVI (Digital Video Interface)

HDMI1, HDMI2 (High Definition Multimedia Interface)

PC RGB

AV(composite) Sound in/Out

PC Stereo Sound

Audio Out

ACTIVE DISPLAY AREA (W x H)

376.32mm X 301mm (14.82’’ X 11.85’’)

PACKING DIMENSIONS (W x H x D)

477mm X 543mm X 205mm (18.78’’ X 21.38’’ X 8.07’’)

WEIGHT

Net Weight : 7.17Kg (15.81 lbs)

Gross Weight : 8.94Kg (19.71 lbs)

ELECTRICAL RATINGS

12V 3.5A

▶▶ NOTE : Technical specifications are subject to change without notice.

- 19 -

2. Touch Screen Specification

Specification

TOUCH

SCREEN

Rating

Voltage
Operating Temperature Range
Storage Temperature Range

DC 5Volts

-20℃ to 70℃

-40℃ to 85℃

Optical

Transmittance

More then 90%
(subjected to surface finishies)

Electrical

Resistanse between Leads
Linearity
Insulation Resistance
Chattering Time

50~300 Ω
Less than 1.5%
10MΩ or more at DC 25V
Less than 3ms

Mechanical

Input Methed

Surface Hardness

Bared hand or finger,
conductive metal
3H

Reliability

High Temperature Test
Low Temperature Test
Humidity Test

120 hours at 85 ℃
120 hours at -50 ℃
120 hours at 80 ℃, 90% RH

Durability

Touch Life

Touch 100 million Times
(Ø 2 Manuscript Pen)
(force: 250gf, speed: 2cycles/sec)

Interface

USB

2.0 Compliant

▶▶ NOTE : Technical specifications are subject to change without notice.

- 20 -

WEEE Symbols

- 21 -

Correct Disposal of This Product
(Waste Electrical & Electronic Equipment)

(Applicable in the European Union and other
European countries with separate collection systems)

This marking shown on the product or its literature,
indicates that it should not be disposed with other
household wastes at the end of its working life. To
prevent possible harm to the environment or human
health from uncontrolled waste disposal, please
separate this from other types of wastes and
recycle it responsibly to promote the sustainable
reuse of material resources. Household users should
contact either the retailer where they purchased this
product, or their local government office, for details of
where and how they can take this item for
environmentally safe recycling. Business users
should contact their supplier and check the terms
and conditions of the purchase contract. This product
should not be mixed with other commercial wastes
for disposal.

MEMO

MEMO

MEMO

L39ME0147 Rev.4