The following statement applies to all products that have received FCC approval.
Applicable products bear the FCC logo, and/or an FCC ID in the format FCC ID: GSSVS13761 on the product label.
This mobile device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This mobile device may not cause harmful interference,
and (2) this mobile device must accept any interference received, including
interference that may cause undesired operation. This mobile device has been tested
and found to comply with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
The antenna(s) used for this transmitter must not be colocated or operating in
conjunction with any other antenna or transmitter.
RF EXPOSURE INFORMATION (FCC SAR)
DEVICE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO
RADIO WAVES.This device is designed and manufactured not to exceed the
emission limits for exposure to radio frequency (RF) energy set by the Federal
Communications Commission of the U.S. Government.
The exposure standard for wireless mobile devices employs a unit of measurement
known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is
1.6W/kg. Tests for SAR are conducted using standard operating positions accepted by
the FCC with the device transmitting at its highest certified power level in all tested
frequency bands. Although the SAR is determined at the highest certified power level,
the actual SAR level of the device while operating can be well below the maximum
value. This is because the device is designed to operate at multiple power levels so as
to use only the poser required
to reach the network. In general, the closer you are to a wireless base station antenna,
the lower the power output.
The highest SAR value for the device as reported to the FCC when tested for use
when worn on the body, as described in this user guide, is 1.39 W/kg. (Body-worn
measurements differ among device models, depending upon available accessories
and FCC requirements.)
ViewSonicViewPad 71
While there may be differences between the SAR levels of various devices and at
various positions, they all meet the government requirement.
The FCC has granted an Equipment Authorization for this device with all reported
SAR levels evaluated as in compliance with the FCC RF exposure guidelines. SAR
information on this device is on file with the FCC and can be found under the Display
Grant section of www.fcc.gov/oet/ea/fccid/ after searching on FCC ID: GSS-VS13761.
For Canada
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
This Category II radiocommunication device complies with Industry Canada Standard
RSS-310.
Ce dispositif de radiocommunication de catégorie II respecte la norme CNR-310
d’Industrie Canada.
IMPORTANT NOTE: IC Radiation Exposure Statement
This EUT is compliance with SAR for general population/uncontrolled exposure limits
in IC RSS-102 and had been tested in accordance with the measurement methods
and procedures specified in IEEE 1528. This equipment should be installed and
operated with minimum distance 0.5cm between the radiator & your body.
This device and its antenna(s) must not be co-located or operating in conjunction with
any other antenna or transmitter.
The County Code Selection feature is disabled for products marketed in the US/
Canada.
For product available in the USA/ Canada markets, only channel 1~11 can be
operated. Selection of other channels is not possible.
CE SAR Information
THIS MOBILE DEVICE MEETS GUIDELINES FOR EXPOSURE TO RADIO WAVES.
Your mobile device is a radio transmitter and receiver. It is designed not to exceed the
limits for exposure to radio waves recommended by international guidelines. These
guidelines were developed by the independent scientific organization ICNIRP and
include safety margins designed to assure the protection of all persons, regardless of
age and health.
The exposure guidelines for mobile devices employ a unit of measurement known as
the Specific Absorption Rate or SAR. The SAR limit stated in the ICNIRP guidelines is
2.0 W/kg averaged over 10 grams of tissue. Test for body worn SAR, the positions of
the device are at a minimum of 1.5cm from the body with the device transmitting at its
highest certified power level in all tested frequency bands. The actual SAR level of an
operating device can be below the maximum value because the device is designed to
use only the power required to reach the network. That amount changes depending
on a number of factors such as how close you are to a network base station. The
highest SAR value under the ICNIRP guidelines for use of the device at the body is
0.43 W/kg. Use of device accessories and enhancements may result in different SAR
values. SAR values may vary depending on national reporting and testing
requirements and the network band.
CE Conformity for European Countries
The device complies with the EMC Directive 2004/108/EC and Low
Voltage Directive 2006/95/EC.
ViewSonicViewPad 72
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical and
Electronic Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as
unsorted municipal waste, but use the return and collection systems according
to local law.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery has a
heavy metal content of more than 0.0005% Mercury, or more than 0.002%
Cadmium, or more than 0.004% Lead.
European Union Regulatory Conformance
The equipment complies with the RF Exposure Requirement 1999/519/EC, Council
Recommendation of 12 July 1999 on the limitation of exposure of the general public to
electromagnetic fields (0–300 GHz). This equipment meets the following conformance
standards: EN62311, EN60950-1, IEC60950-1, EN50332-1/2, EN301489-1,
EN301489-3, EN301489-7, EN301489-17, EN301489-24, EN301511, EN301908-1/2,
EN300328, EN300440-1/2, EN55022, EN55024.
For the device which is tested in accordance to EN60950-1:2006, it is
mandatory to perform audio tests for EN50332. The device has been tested
to comply with the Sound Pressure Level requirement laid down in the
applicable EN 50332-1 and EN 50332-2 standards. Permanent hearing
loss may occur if earphones or headphones are used at high volume for prolonged
periods of time.
A pleine puissance, l’écoute prolongée du baladeur peut endommager l’oreille de
l’utilisateur.
The conformity assessment procedure has been followed with the involvement of the
following Notified Body:
PHOENIX TESTLAB
Identification mark: CE0700 (Notified Body) CE
This equipment may be operated in:
ATBEBGCHCYCZDEDK
EEESFIFRGBGRHUIE
ITISLILTLULVMTNL
NOPLPTROSESISKTR
0700
We, hereby, declare that this cellular, Wi-Fi, & Bluetooth radio is in compliance with
the essential requirements and other relevant provisions of Directive 1999/5/EC.
Products with 2.4-GHz Wireless LAN Devices France
For 2.4-GHz wireless LAN operation of this product, certain restrictions apply. This
equipment may use the entire-2400-MHz to 2483.5-MHz frequency band (channels 1
through 13) for indoor applications. For outdoor use, only 2400-2454 MHz frequency
band (channels 1-9) may be used. For the latest requirements, see http://www.arttelecom.fr.
Guarantee of Provision of Operating Instructions
This company hereby guarantees that all large-screen smartphones sold (or
manufactured) by it (including their LP RF electric devices or modules) (brand:
ViewSonic, model number: VS13761) shall have operating instructions inside the
packaging when they are made available on the market. The instructions or external
packaging of the products shall contain: (1) a warning that reads, “Use properly to
ViewSonicViewPad 73
reduce the effect of electromagnetic waves”; (2) a measured value of SAR 0.43W/Kg;
(3) instructions on the safe use of batteries/electric power; (4) a warning that reads,
“Without permission, companies, stores or users shall not arbitrarily change or amplify
the power or modify the features and functions of the original design of this LP RF
electric device, which has obtained an LP approval certificate”; and (5) a warning that
reads, “Use of LP RF electric devices shall not impact flight safety or interfere with
legitimate telecommunication. If interference is found, use of the device shall be
immediately terminated, and usage shall not resume until the interference is
eliminated. Legitimate telecommunication refers to wireless telecommunication
conducted as per the Telecommunications Act. LP RF electric devices must endure
the interference caused by electrical waves sent out or radiation produced by
legitimate telecommunication or industrial, scientific and medical devices.” If this
company contravenes its guarantee, it shall unconditionally accept revocation of the
approval certificate issued to it, be held legally responsible, and pay for all losses
suffered by the users.
ViewSonicViewPad 74
Important Safety Instructions
1.DO NOT place objects on top of the ViewPad, as objects may scratch the screen.
2.DO NOT expose the ViewPad to dirty or dusty environments.
3.DO NOT place the ViewPad on an uneven or unstable surface.
4.DO NOT insert any foreign objects into the ViewPad.
5.DO NOT expose the ViewPad to strong magnetic or electrical field.
6.DO NOT expose the ViewPad to direct sunlight as it can damage the LCD Screen.
Keep it away from heat sources.
7.SAFE TEMPERATURE: This ViewPad should only be used in environments with
ambient temperatures between 5°C (41°F) and 35°C(95°F).
8.DO NOT use the ViewPad in the rain.
9.Please check with your Local Authority or retailer for proper disposal of electronic
products.
10. The ViewPad and the adapter may produce some heat during normal operation or
charging. DO NOT leave the ViewPad on your lap to prevent discomfort or injury
from heat exposure.
11. POWER INPUT RATING: Refer to the rating label on the ViewPad and be sure
that the power adapter complies with the rating. Only use accessories specified
by the manufacturer.
12. DO NOT use a pen or any sharp object to tap the screen.
13. Clean the touch screen with a soft cloth. If needed, dampen the cloth slightly
before cleaning. Never use abrasives or cleaning solutions.
14. Always power off the ViewPad to install or remove external devices that do not
support hot-plug.
15. Disconnect the ViewPad from an electrical outlet and power off before cleaning
the ViewPad.
16. DO NOT disassemble the ViewPad, only a certified service technician should
perform repair.
17. The ViewPad has apertures to disperse heat. DO NOT block the ViewPad
ventilation, the ViewPad may become hot and malfunction as a result.
ViewSonicViewPad 75
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive 2002/
95/EC of the European Parliament and the Council on restriction of the use of certain
hazardous substances in electrical and electronic equipment (RoHS Directive) and is
deemed to comply with the maximum concentration values issued by the European
Technical Adaptation Committee (TAC) as shown below:
SubstanceProposed Maximum ConcentrationActual Concentration
Lead (Pb)0.1%< 0.1%
Mercury (Hg)0.1%< 0.1%
Cadmium (Cd)0.01%< 0.01%
Hexavalent Chromium (Cr
Polybrominated biphenyls (PBB)0.1%< 0.1%
Polybrominated diphenyl ethers (PBDE)0.1%< 0.1%
6+
)
0.1%< 0.1%
Certain components of products as stated above are exempted under the Annex of
the RoHS Directives as noted below:
Examples of exempted components are:
1.Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other
lamps not specifically mentioned in the Annex of RoHS Directive.
2.Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and
electronic ceramic parts (e.g. piezoelectronic devices).
3.Lead in high temperature type solders (i.e. lead-based alloys containing 85% by
weight or more lead).
4.Lead as an allotting element in steel containing up to 0.35% lead by weight,
aluminium containing up to 0.4% lead by weight and as a cooper alloy containing
up to 4% lead by weight.
Permissions.
This product has an Android™ platform based on Linux, which can be expanded by a
variety of JME-based application SW.
All products used in this device and trademarks mentioned herein are trademarks or
registered trademarks of their respective owners.
Google™, the Google logo, Android™, the Android logo and Gmail™ are trademarks
of Google Inc. Use of this trademark is subject to Google Permissions.
Wi-Fi and the Wi-Fi CERTIFIED logo are registered trademarks of the Wireless
Fidelity Alliance.
microSD™ is a trademark of SD Card Association.
Bluetooth and the Bluetooth logo are trademarks owned by Bluetooth SIG, Inc.
Java, JME and all other Java-based marks are trademarks or registered trademarks
of Sun Microsystems, Inc. in the United States and other countries.
The prediction engine of the input method is TOUCHPAL, provided by COOTEK.
DataViz and RoadSync are registered trademarks of DataViz, Inc. All rights reserved.
DataViz and Documents To Go are trademarks or registered trademarks of DataViz,
Inc. All rights reserved.
Word To Go™, Sheet To Go®, Slideshow To Go®, PDF To Go® and icons are
trademarks or registered trademarks of DataViz, Inc. All rights reserved.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or
omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
the right to change product specifications without notice. Information in this document
may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for
any purpose without prior written permission from ViewSonic Corporation.
Intellectual Property Right Information
Right to all technologies and products that comprise this device are the property of
their respective owners:
This product has an Android platform based on Linux, which can be expanded by a
variety of Java-Script-based application SW.
Google, the Google logo, Android, the Android logo, Gmail, and YouTube are
trademarks of Google Inc.
Bluetooth and the Bluetooth logo are trademarks owned by Bluetooth SIG, Inc.
Java, JME and all other Java-based marks are trademarks or registered trademarks
of Sun Microsystems, Inc. in the United States and other countries.
microSD is a trademark of SD Card Association.
The prediction engine of the input method is TOUCHPAL, provided by COOTEK.
ViewSonicViewPad 77
Product Registration
To meet your future needs, and to receive any additional product information as it
becomes available, please register your product on the Internet at:
www.viewsonic.com.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
Product disposal at end of product life
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
volume button to decrease
volume or the right to
increase volume.
ViewSonicViewPad 71
Down
Chapter 1: Getting Started
ResetMIC
Headphones jack:
Use a headphones for
hands-free conversation
or listening to music.
Side
Power:
• Press and hold for 5
seconds to turn the
device on or off.
• To save battery, quick
press to temporarily
turn the screen on or
off.
Mini-USB port:
• Connect USB cable to PC as a
modem /USB mass storage.
• Connect USB cable and the AC
adapter to charge the battery.
Speakers
1.2 Accessories
Your package comes with the following items. If any of them is missing, please contact
your retailer.
•ViewPad 7
•AC adapter / Charger
•Mini USB cable
•Headphones
•Leatherette Cover
•Quick Start Guide
ViewSonicViewPad 72
Chapter 1: Getting Started
1.3 Installing SIM Card and Memory
Card
A SIM card & memory card
SIM card contains your phone number and network
service details. You will need a microSD® card to store
photos, music, videos and other data.
To install the SIM card/microSD card
1. Open the card cover.
2. Insert SIM card/micro SD card as shown. Make sure
the gold contacts are facing up.
3. Close the card cover.
To remove the SIM card
1. Open the card cover.
2. Push to eject the SIM card from the slot.
3. Close the card cover.
To remove the memory card
1. For safe removal, tap Application Drawer > Settings > SD card, USB Mass
storage & phone storage > Unmount SD card.
2. Open the card cover.
3. Push to eject the micro SD card to eject it from the slot.
NOTE: Do not remove the memory while the device is turned on. Sudden removal of
the memory card may cause data loss or unpredictable system hang up.
1.4 Charging the Battery
From new the battery is only partically charged. To fully charge the battery, charge it
for 2 hours.
To charge the battery
1. Connect one end of the AC adaptor to the mini
USB connector of the device as shown.
2. Plug the other end of the AC adaptor to the wall
outlet to start charging.
When the battery is charging, the red LED is
activated; the icon is also displayed in the
status bar. When battery is fully charged, the red
LED disappears and the green LED is activated; if
the device is turned on, the icon is also displayed in the status bar.
ViewSonicViewPad 73
Chapter 1: Getting Started
NOTE:
• The battery can also be charged when device connects to computer through
USB cable. (Although charging time may signficatly increase)
• The battery life may vary depending on user usage.
1.5 Using Headphones
For hands-free conversation or listening to music, plug in headphones to the
headphone connector.
NOTE:
• When using headphones, your ability to hear outside sounds may be limited.
Do not use headphones if it will endanger you.
• Do not set the volume to its maximum when using headphones as it may
damage your hearing.
1.6 Turning the Device On or Off
After installing the SIM card and charging the battery, device is ready to turn on.
To turn on your device
Press and hold the power button until the device vibrates.
To turn off your device
1. Press and hold the power button for 5 seconds.
2. A pop-up window appears, tap Power off.
3. Select OK to confirm.
To set your device to Sleep mode
To set this device to sleep mode, press the power button briefly.
This turns the display off.
To turn the display on, press again the power button briefly.
ViewSonicViewPad 74
Chapter 1: Getting Started
1.7 Unlocking the Screen
To unlock the screen
1. Press the power button or front buttons briefly to turn on display from Sleep mode.
2. Tap and swipe upwards to unlock the screen.
1.8 Turning the Sound On or Off
To enable/disable the sound
1. Press the power button or front buttons briefly to turn on display from Sleep mode.
2. Tap and swipe downwards to turn the sound off.
3. To turn on the sound, repeat the steps above.
ViewSonicViewPad 75
Chapter 2: The Basics
Chapter 2: The Basics
2.1 Home Screen
From the Home screen, you can quickly access common features and view
notifications of missed calls, received messages, check battery and connection status.
Status bar
• Displays status and
notification icons
and clock.
• Message,
appointment, task,
Google Search
Enter the text
you want to
search in the
box.
and connection
notifications are
also displayed here.
Application Drawer
Tap to view the
applications and device
settings.
Shortcut Menu
Tap an icon to
access the
function.
Status Bar Icons
The Status bar icons indicate different types of information. Tap the status bar and
swipe down to view ongoing phone activities or notifications easily. To close the
window, press .
ViewSonicViewPad 76
The icons on status bar indicates the following information:
Notification icon
Text message icon
USB connection
icon
Chapter 2: The Basics
Battery icon
Signal strength icon
Network icon
Wi-fi icon
Bluetooth icon
Volume icon
The following icons may appear in the
volume area.
IconDescription
Sound is off.
Vibrate mode is activated.
Speakerphone is on.
Phone is muted.
Battery icon
The following icons may appear on the
battery icon area:
IconDescription
Battery is full.
Battery is low.
Battery is charging.
To charge the battery, see “Charging the
Battery” on page 3.
To adjust the volume, see “Adjusting the
Volume” on page 12.
Phone Network icon
The following icons may appear on the phone network icon area.
IconDescription
IconDescription
Call is in progress.
No network signal
Call is on hold.
Maximum signal strength. Fewer
bars indicate lower signal
strength.
GPRS network is in use.
No SIM card inserted.
ViewSonicViewPad 77
Chapter 2: The Basics
Connection icon
The following icons may appear on the
connection icon area.
IconDescription
WiFi is connected.
Bluetooth connection is active.
GPRS data connection is active.
HSDPA data connection is
active.
Device is connected to PC via
USB connector.
File has been downloaded.
Notification icon
The following icons may appear on the
notification icon area.
IconDescription
New text message notification
New WAP Push notification
New email notification
New Google mail notification
Alarm
Task notification
Missed call notification
ViewSonicViewPad 78
Chapter 2: The Basics
Shortcut Menu
To easily access the menu, tap the item on the Home screen.
Customizing the Shortcut menu
To add a shortcut:
1. Tap Menu > Add > Shortcuts.
2. Tap Applications to display the list of applications.
3. Tap to add the items that you want to appear on Home screen.
To remove a shortcut:
1. Tap and hold the desired shortcut icon. The icon enlarges.
2. appears on the right of Home screen.
3. Drag the icon to to delete. The shortcut icon is then removed.
ViewSonicViewPad 79
Loading...
+ 46 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.