ViewSonic VS12075 User Manual
ViewSonic
®
Digital Photo Frame
DPX702
- Quick Start Guide
Model No. : VS12078
- Quick Start Guide
- Guide de démarrage rapide
- Guía de Inicio Rápido
Model No. : VS12075
Digital Photo Frame
ViewSonic
®
DPX802
Quick start guide
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the
following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that
may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy, and if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly
approved by the party responsible for compliance could void your authority to
operate the equipment.
For Canada
• This Class B digital apparatus complies with Canadian ICES-003.
• Cet appareil numérique de la classe B est conforme à la norme NMB-003
du Canada.
CE Conformity for European Countries
The device complies with the requirements of the EEC directive
2004/108/EC as amended by 92/31/EEC and 93/68/EEC Art.5 with
regard to “Electromagnetic compatibility”, and 2006/95/EC as amended
by 93/68/EEC Art.13 with regard to “Safety.”
Following information is only for EU-member states:
The mark shown to the right is in compliance with the Waste Electrical
and Electronic Equipment Directive 2002/96/EC (WEEE).
The mark indicates the requirement NOT to dispose the equipment as
unsorted municipal waste, but use the return and collection systems
according to local law.
English
2
Quick start guide
3
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth. If still not clean, see “Cleaning the Display” in
this guide for further instructions.
7.
Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding
type plug has two blades and a third grounding prong. The wide blade and
the third prong are provided for your safety. If the provided plug does not t
into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at
plugs. Convenience receptacles and the point where they exit from the
unit. Be sure that the power outlet is located near the unit so that it is easily
accessible.
11. Only use attachments/accessories specied by the manufacturer.
12.
Use only with the cart, stand, tripod, bracket, or table specied
by the manufacturer, or sold with the unit. When a cart is used,
use caution when moving the cart/unit combination to avoid
injury from tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when
the unit has been damaged in any way, such as: if the power-supply cord or
plug is damaged, if liquid is spilled onto or objects fall into the unit, if the
unit is exposed to rain or moisture, or if the unit does not operate normally
or has been dropped.
English
Quick start guide
Declaration of RoHS Compliance
This product has been designed and manufactured in compliance with Directive
2002/95/EC of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS
Directive) and is deemed to comply with the maximum concentration values
issued by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Proposed Maximum
Concentration
Actual
Concentration
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr6+) 0.1% < 0.1%
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers
(PBDE)
0.1% < 0.1%
Certain components of products as stated above are exempted under the Annex of
the RoHS Directives as noted below:
Examples of exempted components are:
1. Mercury in compact uorescent lamps not exceeding 5 mg per lamp and in
other lamps not specically mentioned in the Annex of RoHS Directive.
2. Lead in glass of cathode ray tubes, electronic components, uorescent tubes,
and electronic ceramic parts (e.g. piezoelectronic devices).
3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by
weight or more lead).
4. Lead as an allotting element in steel containing up to 0.35% lead by weight,
aluminium containing up to 0.4% lead by weight and as a cooper alloy
containing up to 4% lead by weight.
English
4
Quick start guide
5
English
Package contents
Check your Digital Photo Frame package for the following items.
• Digital Photo Frame
• Power adapter
• Stand
• Quick Start Guide
• USB cable
• Replacement front panel*
* The bundled front panel varies depending on the model you purchase.
Replacing front panel
If your Digital Photo Frame package contains a spare front panel, follow these
instructions to replace the front panel for personal preference.
1. Locate the indent on the edge
near the memory card socket.
2. Follow the direction of the gure
and gently lift the front panel.
3. To install a new front panel, align
the panel edge to the Digital
Photo Frame and gently place the
panel on the device.
1
2
3
Quick start guide
English
6
Connect
Button Function
OK Enter or conrm the selection
Left
Move to the previous or left selection
Right Move to the next or right selection
Up Move upward
Down Move downward
Power On/Off
Locate control keys (in the back panel)
Locate the control buttons in the back panel according to the following
table.
2. Plug the power adapter from the device to a power outlet.
1. Align the head of the stand with the
socket, then rotate clockwise until the
stand locks into place.
Turn ON/OFF the device
Turn on the device
Press turn on the device, then the main
screen appear. The LED will light up in blue
color.
Turn off the device
Hold for 2 seconds then release to turn off
the device.
Tips: If you can’t turn on the device normally, please try to turn off the device
then turn it on again.
Loading...