ViewSonic VS11856 User Manual

Precision by ViewSonic

Home Theater Projector

User’s Manual

ENG

FRN

ESP

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

For Canada

• This Class B digital apparatus complies with Canadian ICES-003.

• Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.

CE Conformity for European Countries

The device complies with the requirements of the EEC directive 2004/108/EC as amended by 92/31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic compatibility”, and 2006/95/EC as amended by 93/68/EEC Art.13 with regard to “Safety.”

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE). The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth. If still not clean, see “Cleaning the Display” in this guide for further instructions.

Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s

7. instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade and the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs. Convenience receptacles and the point where they exit from the unit. Be sure that the power outlet is located near the unit so that it is easily accessible.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufac

13. Unplug this unit when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the unit has

turer, or sold with the unit. When a cart is used, use caution when moving the cart/unit combination to avoid injury from tipping over.

been damaged in any way, such as: if the power- supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.

Compliance Information

Declaration of RoHS Compliance

This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex of the RoHS Directives as noted below:

Examples of exempted components are:

1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other lamps not specifically mentioned in the Annex of RoHS Directive.

2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and electronic ceramic parts (e.g. piezoelectronic devices).

3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).

4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium con taining up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.

Proposed Maximum

Concentration

Actual Concentration

Copyright© ViewSonic© Corporation, 2008. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA. PS/2, VGA and XGA are registered trademarks of International Business Machines Corpora tion. Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product. In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specifications without notice. Information in this document may change without notice. No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To meet your future needs, and to receive any additional product information as it becomes available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic® Wizard CD-ROM also provides an opportunity for you to print the registration form, which you may mail or fax to ViewSonic.

For Your Records

Product Name:

Model Number: Document Number: Serial Number: Purchase Date:

The lamp in this product contains mercury. Please dispose of in accordance with local, state or federal laws.

Pro8100 Home Theater Projector VS11856 Pro8100_UG_ENG Rev. 1C 04-16-08 _________________________________ _________________________________

ENG

Compliance Information...........i

FCC Statement

For Canada

CE Conformity for European Countries

Following information is only for EU-member states

Important Safety Instructions

Declaration of RoHS Compliance

Product Registration

Chapter 1: Introduction............1

Projector Features

Notes on the AC Power Cord

Package Contents

Projector Overview

Control Panel

Connection ports

Remote Control

Installing the Batteries

Remote Control Operation

Chapter 3: Remote Control

direct acess............................12

Picture Modes

Color Temperature

PCS (Precision Color System)

HQV

Black Level

Daylight Sensor

Input Source Select

Direct Input Keys

Aspect Ratio

Overscan

Freeze

Keystone

Zoom and Focus

Lens Shift

Power

Light

Chapter 4: ADVANCED OPERA-

TION (OSD Menu).................20

Chapter 2: Installation.............6

Power connection

Audio and Video Devices Connectivity Configuration

Adjusting the Projected Image

Adjusting Projection Image Size

Projection Screen Selection

1. Main Menu

2. Setup Menu

2-1. Picture Sub-Menu

2-1-1 Basic Sub-Menu

2-1-2 Color Temperature Sub-Menu

2-1-3 Image Adjust Sub-Menu

2-1-4 Aspect Ratio

2-1-5 Overscan

2-1-6 Geometry Adjust

2-2. Advanced Sub-Menu

2-2-1 Picture Mode

2-2-2 Black Level

2-2-3 HQV

2-2-4 Noise Reduction

2-2-5 Color Space

2-3 Config Sub-Menu

2-3-1 Projector Settings

2-3-2 OSD

2-3-3 Languages

2-3-4 Timers

2-3-5 High Altitude

2-3-6 Auto Iris

2-4 PCS Settings Sub-Menu

2-4-1 PCS

2-4-2 PCS Display

2-4-3 Flesh tone

2-4-4 Edge Enhancement

2-4-5 Gamma Correction

2-4-6 3D Color Management

2-5 Memory Settings Sub-Menu

2-5-1 Custom Color Temperature

2-5-2 Save

2-5-3 Load

2-5-4 Reset

2-5-5 System Status Screen

Chapter 5: Making and Recalling

the User Adjustments.................42

Making Adjustments

1-1. User Picture Mode Adjustments

1-2. User Color Temperature Adjustments

1-3. User PCS Adjustments

2-1 Recalling the User Picture Mode &

Color Temperature

2-2 Recalling the User PCS Adjustments

2-3 Recalling Both User Picture Mode and

User PCS (Custom 1 & 2)

Appendix...............................46

Maintenance

Cleaning the Lens

Cleaning the Projector Housing

Maintaining the Air Filter

Replacing the Air Filter

Replacing the Lamp

Troubleshooting

List of Compatible Signals

LED Indicator Message

Product Specification

RS232 command code

Remote control code

Customer Support

Limited Warranty

Introduction

Ground

Chapter 1: Introduction

Projector Features

The projector integrates high-performance optical engine projection and a user-friendly design to

deliver high reliability and ease of use.

• 1080P (1920x1080) Full HD native resolution.

• C2 FineTM LCD panel for superior performance.

• Silicon Optix HQVTM for highest quality video.

• Precision Color System for true color image enhancement.

• Power horizontal and vertical lens shift.

• HDMI 1.3 support with HDCP compliance.

• 1.6x power optical zoom lens.

• Auto-iris enables high contrast to produce deeper black levels.

• Daylight sensor for auto setting based on ambient light conditions.

• 1080p 24fps capable

• Full discrete IR and RS-232 command codes

Notes on the AC Power Cord

AC Power Cord must meet the requirement of countries where you use this projector. Please confirm your

AC plug type with the graphics below and ensure that the proper AC Power Cord is used. If the supplied

AC Power Cord does not match your AC outlet, please contact your sales dealer. This projector is

equipped with a grounding type AC line plug. Please ensure that your outlet fits the plug. Do not defeat

the safety purpose of this grounding type plug. We highly recommend using a video source device also

equipped with a grounding type AC line plug to prevent signal interference due to voltage fluctuations.

Package Contents

When you unpack the projector, make sure you have all these components:

Projector Projector dust

Micro-fiber wiping

cloth

1. Projector

2. Projector dust cover. x1

3. Component (RCA) cable x1

4. Power cord x1

5. HDMI cable x1

Batteries Remote control Quick start guide User Guide

cover

Component (RCA)

cable

6. Micro-fiber wiping cloth. x1

7. AA size batteries for remote control x 2

8. Remote control x1

9. Quick start guide x1

10. User Guide x1

Power cord

HDMI cable

ENG

« NOTE »

• Save the original shipping carton and packing material; they will come in handy if you ever to ship

your unit. For maximum protection, repack your unit as it was originally packed at the factory.

• Accessories and components may vary by retailer and region.

Projector Overview

(3)

(6)

(5)(5)

(4) (11)(12)

(7) (8) (9) (10)(2) (1)

(13)(14)

(15)

(1)

(3)

(2)

(4)

(5)

(6)

(7) (8)

(9)

(10)

Control Panel

LED indicator:

1. Daylight sensor.

2. Power indicator

Refer to “LED Indicator Message” (Page 50).

3. Status indicator

Refer to “LED Indicator Message” (Page 50).

Button Function:

1. Control panel

2. LED indicator

3. Air inlet grille

4. Front IR remote control sensor

5. Elevation foot

6. Elevation button

7. Connection ports

8. Rear IR remote control sensor

« NOTE »

• This projector can be used with a ceiling mount for support. The ceiling mount is not included

in the package.

9. Kensington lock

10. Air outlet grille

11. Lamp cover

12. Air filter cover

13. AC power socket

14. Projection lens

15. Ceiling mount (3-M6)

4. Source

Manually selects an input source.

5. Lens Shift

Motorized vertical and horizontal lens

shift for positioning display image

without physically moving the unit.

6. Zoom/Focus

Motorized zoom and focus adjust.

7. Four directional buttons

Use four directional buttons to select items

or make adjustments to your selections.

8. Enter

To confirm selected menu item.

9. Power

Turn on or off the projector.

10. Menu/Exit

Opens and Exits the on-screen menu.

Introduction

(1) (2) (3) (4 ) ( 5) (6) (7 )

(8) (9) (10 ) (11)

(1)

(6)

(7)

(2)

(4)

(3)

(5)

(8)

(9)

(10)

(11)

(12)

(13)

(14)

(15) (16)

Connection ports

1. RS-232 terminal

When operating the projector via a computer, connect this to the controlling computer’s RS-232C port.

2. USB terminal (Service purpose)

This connector is for firmware upgrade.

3. HDMI-1 terminal

Interface for digital video.

4. HDMI-2 terminal

Interface for digital video.

5. RGB IN terminal

Connects PC input signal (analog) to this jack.

6. COMPONENT VIDEO 1 terminals

Analog/digital video interface transmits via three separate signals - Y, Cb/Pb, Cr/Pr.

7. S-VIDEO terminal

Connects S-Video output from video equipment to this jack.

8. DC 5V terminal

9. DC 12V TRIGGER terminal

10. COMPONENT VIDEO 2 terminals

Analog/digital video interface transmits via three separate signals - Y, Cb/Pb, Cr/Pr.

11. COMPOSITE VIDEO terminal

Connects composite video output from video equipment to this jack.

Remote Control

1. POWER

Power On: Discrete power on key.

Power Off: Discrete power off key.

2. MENU

Opens and Exits the on-screen menu.

3. COLOR TEMP

Selections of color shading. Browse

through factory defaults and user

color temp.

ENG

4. PCS

Selection of PCS mode.

PCS On: Use ViewSonic default PCS settings.

USER: Use user defined PCS settings.

PCS Off: Turn off all PCS settings.

5. INPUT SELECT

All: Browse through HDMI 1/2, Component Video 1/2, Composite, S-Video and PC inputs.

HDMI 1: Direct access key for HDMI 1 input.

HDMI 2: Direct access key for HDMI 2 input.

Component Video 1: Direct access key for Component Video 1.

Component Video 2: Direct access key for Component Video 2.

Composite Video and S-Video selection. Browse through Composite Video and S-Video inputs.

PC: Direct access key for PC input.

6. LIGHT

Keypad Light Enable. Keypad will also light up if any other remote control key is pressed.

7. LENS SHIFT

Motorized vertical and horizontal lens shift for positioning display image without physically

moving the unit.

8. ZOOM/FOCUS

Motorized zoom and focus adjust.

9. ASPECT RATIO

Selections of screen proportion.

Normal: Browse through Standard, Full Screen, Crop and Flexview aspect ratios.

Anamorphic 1: Use in conjunction of 16:9 to 2:35:1 conversion lens.

Anamorphic 2: Use in conjunction of 16:9 to 2:35:1 conversion lens.

Note: Requires use of optional .Anamorphic lens. ViewSonic does not provide this optional

lens. For more details on where to purchase the Anamorphic 2.35:1 lens, please visit

www.viewsonic.com

10. FOUR DIRECTIONAL BUTTONS

Use four directional buttons to select items or make adjustments to your selection.

11. ENTER

To confirm selected menu item.

12. EXIT

To Exits the on-screen menu or Cancel the current OSD selection.

13. PICTURE MODE

Selections of picture modes, for easy access to ViewSonic customized presets and customized settings.

All: Browse through Normal, Vivid, Cinema and Professional picture mode.

Custom 1: Recall customized setting 1.

Custom 2: Recall customized setting 2.

14. HQV

HQV enable.

On: Use ViewSonic default HQV settings.

Off: Turn off all HQV settings.

Note: User defined HQV settings can only be accessed in the OSD.

15. DAYLIGHT SENSOR

Daylight sensor enable.

Auto: Daylight mode bases on light sensor detection.

Manual: Manually selects daylight mode.

Off: Turn off daylight mode.

16. BLACK LEVEL

Defines the brightness levels at the darkest visual image point.

Installation

P I C T U

R E

M O D E

A S P E

C T

R A T I O

L E N S S

H I F T

D A

Y L I

G H

S E N

S O R

I E W

C O

L O R

B L A C K

L E V E L

O V E R

S C A N

R E E Z

H Q V

C O

L O R

T E M

E X I T

V / H

K E

Y S T O N

L I

G H T

Z O

O M

/ F O

C U S

C O M P O

N E N T

V I D E

C O M P O

S I T E

V I D E

M E N U

H D M

I D E O

I N P U T

P I C T

U R E

M O D

A S P

E C T

R AT I

L E N S

S H I F

D A

Y L I G

S E

N S O

I E W

C O

L O R

B L A C

E V E L

O V E R

S C A N

R E E Z

H Q V

C O L

O R

T E M

E X

I T

/ H

E Y S T

O N E

L I G H T

O O M

/ F O

C U S

CO M PO

N E NT

V I D E

M POSITE

I D E O

E N U

H D

M I

V I

D E O

I N

P U T

Installing the Batteries

1. Open the battery cover in the direction shown.

2. Install batteries as indicated by the diagram inside the compartment.

3. Close the battery cover into position.

« NOTE »

• Keep the batteries out of the reach of children. There is a danger of death by accidentally

swallowing the battery.

• Remove batteries from remote control when not being used for extended periods.

• Do not dispose of the used battery along with household waste. Dispose of used batteries

according to local regulations.

• Danger of explosion may occur if batteries are incorrectly replaced. Replace all the batteries

with new ones.

Remote Control Operation

Point the remote control at the infrared remote sensor and press a button.

• Operating the projector from the front

• Operating the projector from the rear

« NOTE »

• Do not point the LED light pointer directly to the people’s eyes (especially small children). There

is a danger of injury to the eyes.

• The remote control may not operate when there is sunlight or other strong light such as a

fluorescent lamp shining on the remote sensor.

• Operate the remote control from a position where the remote sensor is visible.

• Do not drop the remote control or jolt it.

• Keep the remote control out of locations with excessively high temperature or humidity.

• Do not get water on the remote control or place wet objects on it.

• Do not disassemble the remote control.

ENG

Chapter 2: Installation

Power cord (example)

Grounding

Power outlet

terminal

Power connection

1. Remove the projector lens cap.

2. Plug the attached power cord into the AC power socket of this projector.

3. Plug the other end of the power cord into a power outlet.

• The power cords for use in the U.S., UK and Europe are included with this projector. Use the

appropriate one for your country.

• This projector uses the power plug of three-pin grounding type. Do not remove the grounding

pin from the power plug. If the power plug doesn’t fit your wall outlet, ask an electrician to

change the wall outlet.

• The provided power cord for the U.S. is rated at 120 V. Never connect this cord to any outlet or

power supply using other voltages or frequencies than rated. If you use a power supply using

other voltage than rated, prepare an appropriate power cord separately.

• Use 100-240 V AC 50/60 Hz to prevent fire or electric shock.

• Do not place any objects on the power cord or do not place the projector near heat sources to

prevent damage to the power cord. If the power cord should be damaged, contact your dealer

for replacement because it may cause fire or electric shock.

• Do not modify or alter the power cord. If the power cord is modified or altered, it may cause fi

re or electric shock.

Caution:

• Plug in the power cord firmly. When unplugging, hold and pull the power plug, not the power cord.

• Do not plug in or out the power cord with your hand wet. It may cause electric shock.

Audio and Video Devices Connectivity Configuration

ViewSonic Pro8100 offers a full complementary video input connectivity - from the hi-tech HDMI

to the basic composite video.

There are vast possibilities of audio & video connectivity configurations user can choose from.

However the best setup combination relies on user’s equipments and using preferences.

Please seek professional advice for best matching setup. The video input type priority sequence is

listed below:

• HDMI

The illustration below shows some recommended setup configuration possibilities.

•Component Video • S-Video • Composite Video

A. Using Home Theater System as hub

FRONT A

CENTER

SURROUND

SPEAKERS

Surround Audio Speakers

Home Theater Receiver

SURROUND

L L

R R

OUT

VIDEO

OUT

COMPOSITE VIDEO

OUTININ

OUT

MONITOR OUT

COMPONENT VIDEO

PB0C

PR0C

OUT

PB0CBPR0C

OUT

VCR

DVD

Set top box

Blue Ray DVD/ HD DVD player

Pro8100

DIGITAL INPUT

DIGITAL OUTPUT

OPTICAL COAXIAL

AUDIO

OUT OUTININ

3 4 5

OUT

HDMI

ININ

S-VIDEO

OUTININ

This setup is recommended if a highly sophisticated home theater system is available.

This setup offers a great ease on utility for user, since settings of both audio and video can be changed without manual matching.

Pros: Eliminate audio and video source matching between projector and audio amplifier. Increase number of connecting devices. Reduce cabling to the projector.

Cons: High cost.

Installation

Note: The illustrated home theater receiver contains HDMI out, component video out, S-Video out and composite video out. Not all home theater receiver has full complementary of video output.

ENG

B. Using Projector as hub

FRONT A

CENTER

SURROUND

SPEAKERS

Surround Audio Speakers

Home Theater Receiver

SURROUND

L L

R R

OUT

HDMI

ININ

S-VIDEO

COMPOSITE VIDEO

VIDEO

OUT

INININ

AUDIO

OUT OUTININ

OUT OUT

OUT

ININ

MONITOR OUT

COMPONENT VIDEO

PB0C

PR0C

OUT

PB0CBPR0C

OUT

VCR

Set top box

DVD

Blue Ray DVD/ HD DVD player

Pro8100

DIGITAL INPUT

DIGITAL OUTPUT

OPTICAL COAXIAL

3 4 5

This setup is recommended for low to mid range home theater system.

When changing input source, both projector and home theater system’s remote controls need to be activated.

Projector and home theater system controls can be centralizing controlled by 3rd party‘s home appliances control system (Projector is via RS232).

Please seek professional advice for best suited type of home appliances control system.

Pros: Low budget.

Cons: It is required to match audio and video sources between projector and audio amplifier manually. Masses of routing cables need to be connected to projector.

C. Connecting Cable or Satellite TV

There’s no build-in TV tuner in ViewSonic Pro8100.

It will only take direct video output (HDMI, Component Video, S-Video or Composite Video.) with cable or satellite set-top-box.

Please use by the recommended input priority order.

Please to use HDMI or Component Video connection only if cable or satellite offers HDTV signals (Check with cable or satellite TV provider.).

Installation

PC or Home Appliances control Host

RS232 Cabel

To monitor port

RGB IN

RGB cable

D. RS232 Connection

The illustration shows the connection to a home appliances control device. ViewSonic Pro8100’s

RS232 command code table and setup protocol are listed in the Appendix section.

E. 12V Screen Curtain Trigger

ViewSonic Pro8100 offers a 12V trigger control pulse upon power-on and power-off. This 12V trigger

pulse can be utilized to motor drive of a home theater’s curtain or a drop-down projection screen.

F. PC Input

ViewSonic Pro8100 can take analog PC video signal by RGB IN (Shown in the illustration below.).

« NOTE »

• When connecting cable, power cords of both a projector and external equipment should be

disconnected from AC outlet.

• The figure above is a sample connection. This does not mean that all of these devices can or

must be connected simultaneously.

• The cables that come with the projector may differ from the above illustration. The included

cables are based on actual shipment delivery.

ENG

Adjusting the Projected Image

Adjusting the Projector Height

The projector is equipped with two elevation feet to adjust the image height.

To raise the image:

1. Press the elevation button.

2. Raise the image to the desired height angle, then release the button to lock the elevation foot

into position.

To lower the image:

1. Press the elevation button.

2. Lower the image, then release the button to lock the elevation feet into position.

« NOTE »

• To avoid damaging the projector, make sure that the elevation feet are fully retracted before

placing the projector in its package.

Adjusting the Projector Lens Position

1. Press the Lens Shift button.

2. Use four directional buttons to adjust the lens position.

The adjustable projection range

Installation

40"

80"

120"

200"

300"

Wide: 1.25m Tele: 2.02m

Wide: 3.75m Tele: 6.06m

Wide: 6.24m Tele: 10.09m

Wide: 9.36m Tele: 15.14m

Wide: 2.5m Tele: 4.04m

Adjusting Projection Image Size

Refer to the graphic and table below to determine the screen size and projection distance.

Projection Screen Selection

ViewSonic Pro8100’s preset image modes are calibrated based on a no-gain, pure flat white

projection screen. For best preset performance, it is highly recommended to use a no-gain, flat

white professional projection screen. The projection screens used in most office are gain-screens.

Material used in brightness gain screen will cause decrease in viewing angle and hot-spot symptom.

Black level and contrast performances can also be altered by the gain-screen since the gain will

also boost the dark level brightness.

the contrast and black level performance.

standard factory presets, when using these types of projection screens.

Please seek professional help for adapting a specialized screen, when calibrating the projector

settings manually.

The so-called hi-contrast gray projection screen can also alter

The best viewing performance can not be brought by the

16 : 9 Screen

Screen Size

(Diagonal)

40” 1.25 49.2 2.02 79.5

50” 1.56 61.5 2.52 99.4

60” 1.87 73.7 3.03 119.2

70” 2.19 86.0 3.53 139.1

80” 2.50 98.3 4.04 159.0

90” 2.81 110.6 4.54 178.8

100” 3.12 122.9 5.05 198.7

120” 3.75 147.5 6.06 238.5

150” 4.68 184.3 7.57 298.1

200” 6.24 245.8 10.09 397.4

250” 7.80 307.2 12.62 496.8

300” 9.36 368.7 15.14 596.2

Wide

Projection Distance

m inch m inch

Tele

Projection Distance

« NOTE »

• Position the projector in a horizontal position; other positions can cause heat build-up and

damage to the projector.

• Make sure all intake and exhaust ventilation are not blocked.

• Do not use the projector in a smoky environment. Smoke residue can cause buildup on critical

parts.

ENG

Chapter 3: Remote Control direct access

Power

Power button to turn on or off the projector.

Power ON

Power OFF

Cancel Power

OFF

Press on the remote control/top panel to turn

on projector.

Press on the remote control/top panel, it would

pop up a confirmation screen showing:

“Press Power Button Again to power off.”

Once this confirmation pops up, Press on the

remote control/top panel again to turn the power off.

After lamp cooling cycle is completed, the unit will

enter Stand-By mode.

Press on the remote control to cancel the

power off process, once this confirmation pops up.

Light

To illuminate remote control key pad backlight.

Light ON, no

action

Light ON, action

Press on the remote control to illuminate the

remote control keypad backlight. Backlight will

automatically switch off after 10 seconds, if no

other key is pressed.

Press any remote control key will illuminate the

keypad backlight and calls up the function at the

same time.

Backlight will automatically switch off after 10

seconds, if no other key is pressed.

Remote Control direct access

Lens Shift

Motorized vertical and horizontal lens shift for positioning display

image without physically moving the unit.

Press on the remote control to evoke lens shift adjustment

function.

Press on the remote control to leave the adjusting section.

Press ▲ on the remote control/top panel to move

display image up.

Press

on the remote control/top panel to move

▼

display image down.

Press ► on the remote control/top panel to move

display image right.

Press

on the remote control/top panel to move

◄

display image left.

Zoom and Focus

Motorized zoom and focus adjust.

Press on the remote control to browse through zoom and

focus adjust options.

Press on the remote control to confirm the selection.

Press on the remote control to leave the adjusting section.

Enlarge/minimise the image optically.

Press

on the remote control/top panel to Zoom in.

►

Press

on the remote control/top panel to Zoom out.

◄

Adjust the clarity and sharpness of the image optically.

Press

and

on the remote control/top panel to

►

◄

adjust the focus.

ENG

Aspect Ratio

Selections of screen proportion.

Press on the remote control to browse through available

aspect ratio options.

Normal: Browse through standard aspect ratio modes.

Anamorphic 1: Use in conjunction of 16:9 to

2.35:1 conversion lens. Morphing a 2.35:1 film

content from a 16:9 letter box to a full screen

2.35:1 output.

Picture Modes

Selections of picture modes, for easy access to ViewSonic customized

presets and customized settings.

Press on the remote control to browse through avail-

able picture modes.

All: Browse through Normal, Vivid, Cinema and Professional picture mode.

CUST 1: Recall customized setting 1.

CUST 2: Recall customized setting 2.

Normal: I mage is presented in original content.

All special enhancement features are off.

Vivid: High contrast, richer colo r and detail en-

han cem ent . Attent ion : Exten ded vie win g may

cause fatigue to the eyes.

Cinema: Emphasis on enhancements of skin tone

performance and cinematic effect.

Anamorphic 2: Use in conjunction of 16:9 to

2.35:1 conversion lens. Morphing a 4:3 or 16:9

film contents from a 16:9 format to a 2.35:1

format.

Note: Requires use of optional .Anamorphic lens. ViewSonic does not

provide this optional lens. For more details on where to purchase the

Anamorphic 2.35:1 lens, please visit www.viewsonic.com

Professional: Emphasis on grayscale accuracy and

color performance.

Cust 1: Recall customized settings 1.

Cust 2: Recall customized settings 2.

+ 42 hidden pages