ViewSonic Q9-1, Q9b-1, VS10863-1W Service Manual

Page 1
ViewSonic Q9-1
Q9b-1
Model No. VS10863-1W
19” Color TFT LCD Display
(Q9-1_Q9b-1_SM Rev. 1a Dec. 2005)
ViewSonic 381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Page 2
Viewsonic Corporation i Confidential - Do Not Copy Q9-1_Q9b-1
Copyright
Copyright © 2005 by ViewSonic Corporation. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation. ViewSonic is a registered trademark of ViewSonic Corporation. All other trademarks used within this document are the property of their respective owners.
Revision History
Revision SM Editing Date ECR Number
Description of Changes Editor
1a 12/19/2005 Initial release Jamie Chang
Page 3
TABLE OF CONTENTS
1. Precautions and Safety Notices
2. Specification
3. Front Panel Function Control Description
4. Circuit Description
5. Adjusting Procedure
6. Trouble Shooting Flow Chart
7. Recommended Spare Parts List
8. Exploded View And Exploded Parts List
9. Block Diagram
10. Schematic Diagrams
11. PCB Layout Diagrams
1 5 8
14
20
34 38
42
44 45 49
Viewsonic Corporation ii Confidential - Do Not Copy Q9-1_Q9b-1
Page 4
1. Precautions and Safety Notices
1-1. Appropriate Operation
(1) Turn off the product before cleaning. (2) Use only a dry soft cloth when cleaning the LCD panel surface. (3) Use a soft cloth soaked with mild detergent to clean the display housing. (4) Use only high quality and safety approved AC/DC power adapter. (5) Disconnect the power plug from AC outlet if the product is not used for a long period of time. (6) If smoke, abnormal noise or strange odor is present, immediately switch the LCD display off. (7) Do not touch the LCD panel surface with sharp or hard objects. (8) Do not place heavy objects on the LCD display, video cable, or power cord. (9) Do not use abrasive cleaners, waxes or solvents for your cleaning. (10) Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dusts and dirt.
- Near any appliance generating a strong magnetic field.
- Place in direct sunlight.
1-2. Caution
No modification of any circuit should be attempted. Service work should only be performed after you are
thoroughly familiar with all of the following safety checks and servicing guidelines.
1-3. Safety Check
Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter circuit,
the voltage is exposed in such areas as the associated transformer circuits.
1-4. Power Supply Requirements
The external power converter for this display utilizes AC and DC cords, AC cord is detachable, but DC cord is
permanently attached. Any attempt to replace another adapter could result in serious problem on the display.
1
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 5
1-5. LCD Module Handling Precautions
1-5.1 Handling Precautions
(1) Since front polarizer is easily damaged, pay attention not to scratch it. (2) Be sure to turn off power supply when inserting or disconnecting from input connector. (3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots. (4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. (5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. (6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when handling. (7) Do not open nor modify the Module Assembly. (8) Do not press the reflector sheet at the back of the module to any directions. (9) In case if a Module has to be put back into the packing container slot after once it was taken out from the
container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may be damaged.
(10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface
Connector of the TFT Module.
(11) After installation of the TFT Module into an enclosure (LCD monitor housing, for example), do not twist nor
bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
(12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances
or regulations for disposal.
(13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module
should be supplied by power complied with requirements of Limited Power Source (IEC60950 or UL1950), or be applied exemption.
(14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit (IEC60950 or
UL1950). Do not connect the CFL in Hazardous Voltage Circuit.
2
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 6
1-5.2 Handling and Placing Methods
Correct Methods: Incorrect Methods:
Only touch the metal frame of the LCD panel or
the front cover of the monitor.Do not touch the
surface of the polarizer.
Surface of the LCD panel is pre
ssed by fingers
and that will probably cause “Mura”.
Take out the monitor with cushions
Taking out the monitor by grasping the LCD
panel.That will probably cause “Mura”.
3
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 7
Place the monitor on a clean and soft foam pad.
Placing the monitor on foreign objects. That will probably scratch the surface of the panel or cause “Mura.”
The panel is placed facedown on the lap. That
will probably cause “Mura.”
4
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 8
2. SPECIFICATIONS
General Specification
Test Resolution & Frequency 1280x1024 @ 60Hz Test Image Size Full Size
Contrast and Brightness Controls
Factory Default: Contrast = 60%, Brightness = 100%
Video Interface
Analog Input Connector DB-15 (Analog), refer the appendix A Default Input Connector Defaults to the first detected input
Video Cable Strain Relief
Equal to twice the weight of the monitor for five minutes
Video Cable Connector DB-15 Pin out Compliant DDC 1/2B Video Signals
1. Video RGB (Analog)
Separate, Video Impedance 75 Ohms (Analog) Maximum PC Video Signal 950 mV with no damage to monitor Maximum Mac Video Signal 1250 mV with no damage to monitor Sync Signals TTL DDC 1/2B Compliant with Revision 1.3 Sync Compatibility Separate Sync
Video Compatibility
Shall be compatible with all PC type computers,
Macintosh computers, and after market video
cards Resolution Compatibility
640 x 350, 640 x 480, 720 x 400 (640 x 400), 800
x 600, 832 x 624, 1024 x 768, 1280 x 720, 1280 x
1024, Exclusions Not compatible with interlaced video
Horizontal / Vertical Frequency
Horizontal Frequency 30 – 82 kHz Vertical Refresh Rate 50 – 75 Hz. Maximum Pixel Clock 140 MHz Sync Polarity Independent of sync polarity.
POWER SUPPLY
Internal Power Supply Part Number: HOAU172001 Input Voltage Range 90 to 264 VAC Input Frequency Range 47.5 to 63 Hertz Over Current Protection 5 A TYPICAL AT 5VDC Leakage Current 3.5MA (MAX) AT 254VAC / 60HZ Efficiency 75 % TYPICAL AT 115VAC FULL LOAD Power Dissipation 45 WATTS (TYP) Max Input AC Current 1.5 ARMS @ 90VAC, 1 ARMS @180VAC Inrush Current (Cold Start) 50 A @ 120VAC, 90 A(MAX) @220VAC
Power Consumption
ON Mode < 45 W (max) / 35 W (typ)
ACTIVE OFF < 1 W Recovery Time ON Mode = N/A, ACTIVE OFF < 3 sec
5
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 9
Timing Table
Item Timing Analog
1 640 x 350 @ 70Hz, 31.5kHz Yes 2 640 x 400 @ 70Hz, 31.5kHz Yes 3 640 x 480 @ 60Hz, 31.5kHz Yes 4 640 x 480 @ 67Hz, 35.0kHz Yes 5 640 x 480 @ 72Hz, 37.9kHz Yes 6 640 x 480 @ 75Hz, 37.5kHz Yes 7 720 x 400 @ 70Hz, 31.5kHz Yes 8 800 x 600 @ 56Hz, 35.1kHz Yes
9 800 x 600 @ 60Hz, 37.9kHz Yes 10 800 x 600 @ 75Hz, 46.9kHz Yes 11 800 x 600 @ 72Hz, 48.1kHz Yes 12 832 x 624 @ 75Hz, 49.7kHz Yes 13 1024 x 768 @ 60Hz, 48.4kHz Yes 14 1024 x 768 @ 70Hz, 56.5kHz Yes 15 1024 x 768 @ 72Hz, 58.1kHz Yes 16 1024 x 768 @ 75Hz, 60.0kHz Yes 17 1280 x 1024 @ 60Hz, 63.4kHz Yes 18 1280 x 1024 @ 75Hz, 79.97kHz Yes 20 1280x 720 @ 60Hz, 45kHz (HDTV) Yes
User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration
Panel Characteristics
Model number “HANNSTAR AND HSD190ME12-A02 Type “TN PANEL TECHNOLOGY” Active Size 376.32 (H) x 301.056 (V) Pixel Arrangement RGB Vertical Stripe Pixel Pitch 0.294 mm Glass Treatment ANTI GLARE (HARD COATING 3H) # of Backlights 4 CCFL EDGE-LIGHT (2 TOP / 2 BOTTOM) Backlight Life 40,000 HOURS (MIN) Luminance – Condition: CT = 6500K, Contrast = Max, Brightness = Max
260 cd/m2 (Typ after 30 minute warm up) 200 cd/m2 (Min after 30 minute warm up)
Brightness Uniformity 75 % Entire Area (minimum) Contrast Ratio 500:1 (Typ), 350:1 (Min) Color Depth 16 million colors (x bit panel) Viewing Angle (Horizontal) 140 deg @ CR>10, 160 deg @ CR>5 (typ) Viewing Angle (Vertical) 130 deg @ CR>10, 150 deg @ CR>5 (typ) Response Time 10%-90% @ Ta=25°C
12 ms (Tr =3.6 ms, Tf = 8.4 ms) (Typ) 25ms (Max)
Panel Defects Please see Panel Quality Specifications.
6
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 10
IMAGE PERFORMANCE
Factory Defaults
Item Defaults Item Defaults Contrast 60% 720x400/640x400 720x400 Brightness 100% Resolution Notice Enabled Color Temperature 6500K Volume N/A Sharpness 50% Balance N/A OSD H. Position 50% Treble N/A OSD V. Position 50% Bass N/A OSD Time Out 20 Sec OSD Blending 100%
Dimension
Width 430 mm Height 435 mm Depth 194 mm Monitor Weight 4.4 kg / 9.68 lbs
Ergonomics
Tilt Up +19° +/- 1° DEGREES MINIMUM Tilt Down -1 °+/- 1° degrees
7
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
2
nd
Source Panel “CPT and CLAA190EA03
Type “Panel Technology” Active Size 376.32 (H) x 301.056 (V) Pixel Arrangement RGB Vertical Stripe Pixel Pitch 0.294 mm GLASS TREATMENT Anti Glare (Hard coating 3H) # OF BACKLIGHTS 4 CCFL edge-light (2 top / 2 bottom) BACKLIGHT LIFE 40,000 Hours (Min) / 50,000 Hours (typ) Luminance –
Condition: CT = 6500K, Contrast = Max, Brightness = Max
250 cd/m2 (Typ after 30 minute warm up) 200 cd/m2 (Min after 30 minute warm up)
Brightness Uniformity 75 % Entire Area (minimum) Contrast Ratio 500:1 (Typ), 400:1 ( Min) Color Depth 16 million colors (x bit panel) Viewing Angle (Horizontal) 150 deg @ CR>10, 170 deg @ CR>5 (typ) VIEWING ANGLE (VERTICAL) 130 deg @ CR>10, 170 deg @ CR>5 (typ) Response Time 10%-90% @ Ta=25°C
12 ms (Tr= 5 ms, Tf = 7 ms) ( Typ) 25 ms (Tr= 10 ms, Tf = 15 ms) (Max)
Panel Defects Please see Panel Quality Specifications.
Page 11
Display Controls
1) MENU
Enter to the OSD adjustment menu. It also used for go back to previous menu for sub-men
u
and the change data don’t save to memory.
2) SELECT:
To confirm the current selection. It also used for go back to previous menu for sub-menu,
and the change data will be saving to memory.
If pressed when menu is not active, VOLUME is adjusted.
3) ADJUST : (RIGHT)
To scroll up in sub menu or to increase value of selected item.
If pressed when menu is not active, BRIGHTNESS is adjusted.
4) ADJUST —: (LEFT)
To scroll down in sub menu or to decrease value of selected item
If pressed when menu is not active, AUTO CINFIG is adjusted.
5) POWER SWITCH:
Pushing the power switch will turn the monitor on. Pushing it again to turn the monitor
off.
6) POWER INDICATOR:
The LED will light with green color in normal on state, and will light with flash in power
saving mode.
3-1 Location of Controls
3. Front Panel Function Control Description
8
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 12
Screen Adjustment Operation Procedure
The Screen Adjustment
Main Menu
1) Entering the screen adjustment The setting switches are normally at stand-
b
y. Push the MENU button once to display the main menu of the screen adjustment. The adjustable items will be displayed in the main menu.
2) Entering the settings
Use the Adjust and Adjust buttons to select the desired setting icon and push the SELECT button to enter sub-menu.
3) Change the settings
After the sub-menu appears, use the Adjust and Adjust buttons to change the setting values.
4) Save After finishing the adjustment, push the SELECT button to memorize the setting.
5) Return & Exit the main menu To go back to the previous menu, push the MEMU button.
The OSD main menu (Figure 8-1) is displayed on screen when MENU key is pressed. The OSD men
u
is a combination of graphic and text display. The column inside the OSD menu will show information o
f
input image. Second column beneath OSD menu shows the item selected.
The LEFT and RIGHT keys are used to scroll through items within the menu. The selected item i
s
highlighted as the scrolling moves along. The SELECT key is used to activate the highlighted ite
m
during this state.
Figure 8-1
3-2 OSD Menu Controls
9
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 13
OSD adjusting and Controls
BRIGHTNESS
Setup the brightness of the panel.
CONTRAST
The Contrast menu item is used to adjust image contrast.
AUTO CONFIG
There are two items: AUTO ADJUST and AUTO COLOR. Use the Adjust [+] an
d
[-] key to scroll up and down in menu, and then press the SELECT key to start thi
s
function. If the MENU key is pressed, the main menu is re-displayed and nothing i
s
changed.
AUTO ADJUST: Used to perform automatic configuration of the phase、clock、
vertical and horizontal positioning.
AUTO COLOR: It is used to adjust the gain and offset of the Red, Green and Blue
channels on the ADC automatically.
H-POSITION
H-Position is used to adjust the horizontal image position manually. A slider wit
h
current value is displayed.
V-POSITION
V-Position is used to adjust the vertical image position manually. A slider wit
h
current value is displayed.
CLOCK
Reduce vertical stripes in the screen image.
PHASE
Reduce horizontal stripes in the screen image.
SHARPNESS
This can adjust the video quality to be sharp or blur (special for text mode).
10
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 14
INFORMATION
The “INFORMATION” menu provides the user with detailed information regarding th
e
current input format and version (include resolution, vertical /horizontal frequency, pixe
l
clock and software version).
COLOR
Configure the image color. There are three items : 9300K、6500K、USER MODE.
9300K: The item “9300K” is used to default 9300K color temperature.
6500K: The item “6500K” is used to default 6500K color temperature.
USER MODE:
RGB ADJUST:
-RED: The item “RED” is used to adjust the gain of red channel in ADC.
-GREEN: The item “GREEN” is used to adjust the gain of green channel in ADC.
-BLUE: The item “BLUE” is used to adjust the gain of blue channel in ADC.
OSD MENU
There are five items: OSD H POSITION, OSD V POSITION, OSD BLENDING, OS
D
TIME OUT and LANGUAGE.
OSD H POSITION: The item “OSD H Position” is used to setup the OSD menu H position.
OSD V POSITION: The item “OSD V Position” is used to setup the OSD menu H position.
OSD BLENDING: To adjust the blending of the OSD MENU.
OSD TIME OUT: “OSD Time out” is used to set the timeout of the OSD menu.
There are three options for the automatic timeout: 20, 40 and 60 seconds.
MISC MENU
There is one item: reset.
RESET: Press “Reset” to return the monitor to its factory default settings.
11
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 15
How to use AUTO CONFIG Adjustment
This function can tune the parameters of PHASECLOCKH-POSITION and V-POSITION.
Suggesting Adjustment Steps
Step 1: Enter the “Windows” Shut-down frame. ( Note:The Wallpaper color CAN NOT be
black.)
Step 2: Enter OSD Main Menu and choose the “AUTO CONFIG” item, then press SELECT
key. The Picture will auto-adjust by itself. After 4 seconds, you can exit OSD and Shut-down frame.
Step 3: If you are not still satisfied with the picture quality, you could choose CONTRAST
item in OSD Main Menu and adjust it.
Note:
1. If you don’t like the effect of AUTO CONFIG adjustment, you can adjust PHASE,
CLOCK… items in OSD.
2. AUTO CONFIG adjustment can be used in “Windows” except black background frame, but
the best effect is in the SHUT DOWN frame.
3. It is recommend running “EDIT” program first, then doing AUTO CONFIG adjustment in
DOS mode.
12
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 16
3-3 Hot Key for Function Controls
Buttons: Functions:
[Manual] Main menu
[Enter] Select / Exit
[+] To immediately activate Brightness menu. [-]
Auto config
[+] + [PW] + Main Power On All Reload
No signal + [Enter] + Main
Power on
Burning mode
Signal + [PW] +[ Enter] + Main
Power on
Factory Mode
Remark : All the short cuts function are only available while OSD off
13
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 17
1. WORKING THEOREM
A. Scaler
The RTD2023 is total solution graphics processing IC for LCD monitors with panel resolutions up to SXGA. It is configured with integrated 8­bit triple-ADC/PLL, a high quality display processing engine, and an integrated output display interface that can support Dual / Single LVDS panel interface format. To further reduce system costs, the RTD2023 also integrates intelligent power management control capability for green-mode requirements and spread-spectrum support for EMI management. The RTD2023 incorporates the world’s first coherent oversampled RGB graphics ADC in a monitor controller system1. The oversampling ADC samples the input RGB signals at a frequency that is much higher than the signal source pixel rate. This can preserve details in the video signal that ordinarily would be lost due to input signal jitter or bandwidth limitations in non-oversampled systems.
B. MCU:
The MTV512M micro-controller is an 8051 CPU core embedded device especially tailored for flat panel display application. It includes an 8051 CPU core, a 768K-byte SRAM, 4 channels of 6-bit ADC,3 external counters / timers ,6 channels of PWM DAC,VESA DDC interface, and a 64k-byte internal program Flash-ROM memory. of 6-bit ADC, and a built-in , It also includes two IIC Slave B ports, supporting VESA DDC/CI for D-sub interfaces, and a Boot-Code-Free ISP (In System Programming).
4. Circuit Description
14
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 18

15
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 19
B. MCU:
Hardware Design Attention :
(1). Reset Time :
(2). Pin assignment of MTV512M and 8051
16
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 20
(3). Special application
17
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 21
18
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 22
19
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 23
5. Adjusting Procedure
5-1. Function Test
5-1.1 Product
19” LCD Monitor
5-1.2 Test Equipment
Color Video Signal & Pattern (or PC with SXGA resolution)
5-1.3 Test Condition
Before function test and alignment, each LCD Monitor should be run-in and warmed up for at least 30 minutes with the following conditions:
(a) In room temperature, (b) With full-white screen, RGB, and Black (c) With cycled display modes,
640*480 (H=43.27 kHz, V=85Hz) 800*600 (H=53.7 kHz, V=85Hz) 1024*768 (H=68.67 kHz, V=85Hz) 1280*1024(H=80.0KHz, V=75Hz)
5-1.4 Test Display Modes & Pattern
5-1.4.1 Compatible Modes
Item Analog Timing
1 640 x 350 @ 70Hz, 31.5kHz 2 640 x 400 @ 70Hz, 31.5kHz 3 640 x 480 @ 60Hz, 31.5kHz 4 640 x 480 @ 67Hz, 35.0kHz 5 640 x 480 @ 72Hz, 37.9kHz 6 640 x 480 @ 75Hz, 37.5kHz 7 720 x 400 @ 70Hz, 31.5kHz 8 800 x 600 @ 56Hz, 35.1kHz
9 800 x 600 @ 60Hz, 37.9kHz 10 800 x 600 @ 75Hz, 46.9kHz 11 800 x 600 @ 72Hz, 48.1kHz 12 832 x 624 @ 75Hz, 49.7kHz 13 1024 x 768 @ 60Hz, 48.4kHz 14 1024 x 768 @ 70Hz, 56.5kHz 15 1024 x 768 @ 72Hz, 58.1kHz 16 1024 x 768 @ 75Hz, 60.0kHz 17 1280 x 1024 @ 60Hz, 63.4kHz 18 1280 x 1024 @ 75Hz, 79.97kHz 20 1280x 720 @ 60Hz, 45kHz (HDTV)
20
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 24
5-1.5.2 Auto Image Adjust
Please select and enter Auto Adjustfunction on Main Menu to see if it is workable. The Auto Adjustfunction is aimed to offer a better screen quality by built-in ASIC. For optimum screen quality, the user has to adjust each function manually.
5-1.5.3 Firmware
Test Pattern: Burn in Mode (Refer to Chapter III-3. Hot Keys for Function Controls) - Make sure the F/W is the latest version.
5-1.5.4 DDC
Test Pattern: EDID program - Make sure it can pass test program.
5-1.5.5 Fine Tune and Sharpness
Test Signal: 1280 x 1024 @ 60.0kHz Test Pattern: Line Moiré Pattern
- Check and see if the image has noise and focus performs well. Eliminate visual line bar.
- If not, readjust by the following steps:
(a) Select and enter “Auto config” function on “Auto Adjust” to
adjust the image to eliminate visual wavy noise.
(b) Then, select and enter “Sharpness” function to adjust the clarity and
focus of the screen image.
5-1.5.6 White Balance
Test Signal: 640*480@60Hz Test Pattern: Full White and Black Pattern
5-1.5.7 R, G, B, Colors Contrast
Test Signal: 1280 x 1024 @ 60.0kHz Test Pattern: R, G, B, Color Intensities Pattern and 16 Gray Scale Pattern
- Check and see if each color is normal and distinguishable.
- If not, please return the unit to repair area.
5-1.5.8 Screen Uniformity and Flicker
Test Signal: 1280 x 1024 @ 60.0kHz Test Pattern: Full White Pattern
- Check and see if it is in normal condition.
21
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 25
5-1.5.9 Dead Pixel and Line
Test Signal: 1280 x 1024 @ 60.0kHz Test Pattern: Dark and White Screen Pattern
- Check and see if there are dead pixels on LCD panel with shadow gauge
and filter film.
- The total numbers and distance of dead pixels should be compliant with the
spec.
5-1.5.10 Mura
Test Pattern: White, RGB, Black, & Grey Test Tool: 10 % ND Filter
- Check if the Mura can pass 10 % ND Filter.
5-1.5.11 Check for Secondary Display Modes
Test Signal: Analog: 640*350@70Hz; 640*400@60Hz;640*480@50/60/67/72/75/85Hz;
720*400@70Hz, 800*600@56/60/72/75/85Hz; 832*624@75Hz, 1024*768@50/60/70/72/75/85Hz; 1280*1024@60/75Hz
- Normally when the primary mode 1280*1024@60Hz is well adjusted and compliant with the specification, the secondary display modes will be great possible to be compliant with the spec. But we still have to check with the general test pattern to make sure every secondary is compliant with the specification.
5-1.5.12 All Modes Reset
After final QC step, we have to erase all saved changes again and restore the factory defaults. You should do “All Mode Reset” again.
5-1.5.13 Power off Monitor
Turn off the monitor by pressing “Power” button.
22
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 26
5-2. Firmware Upgrade Procedure
5-2.1 Equipment Needed
- Q9 Monitor
- Fixture for Firmware Upgrade
- Power Adapter *1 for Fixture (+12V)
- VGA Cable *1
- PC (Personal Computer)
- LPT Cable *1
- Firmware Upgrade Program
- One additional monitor for checking the program execution PC Fixture Printer Port Q9
Q9 Fixture Power Adapter *1 for Fixture
VGA cable PC LPT cable
Printer Port
23
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 27
5-2.2 ISP procedure
Connection of ISP Kit
Using LPT cable connect PC Print port Using VGA cable connect monitor (destination) Plug Power Adapter to Fixture Fixture SW3 select 4 & 8 both
J701:to Power Adapter
CN702:to Q9 monitor
P1: to PC printer port
24
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 28
Setting of ISP program on PC
1. Setup MYSON ISP program,
2. Execute ISP program to get the window below
3. Select “MTV512M64” MTV type,
4. Select CPU=5 MHz
5. Click “Load MCU file” and then find the updated firmware code.
6. Click “Create Security File” going to next window
MTV Type
CPU=5
MCU File
Create Security File
25
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 29
7. Select Command No=4
8. Put ISP Slave Add=94 ; Slave B Add=94 ; Command 1=ac ; Command 2=ca , Command 3=53
9. Click “OK” to start ISP function and update the firmware into Monitor.
10. Firmware update is finished when the display backed to the window then press
“RUN” as below.
2.Input Value
1.Command N
o 3. OK
26
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 30
5.3 . EDID Procedure
DDC User’s manual
1. Hardware installation
A. The EDID cable has equipped 2 different terminals;
one is male 25 pin printer connector and another side is male 15 pin D-sub connecter. B. Connect the EDID cable from PC Printer port to monitor D-sub connector. C. Make sure the monitor was working under power saving mode and keep it at “Power Saving
state” during DDC process.
D-Sub of Monitor
PC printer port 25pin
EDID-Kit Cable
27
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 31
2. Programming procedure
A. Normally, you received a EDID zip file of new model. You need to unzipped it. B. There will need the following files for DDC program: (Q9 is an example)
1. DPS.EXE
2. Q9.BAT
3. Q9.DDC
4. Q9.CFG
5. Q9.DPS
C. Execute the Q9.BAT (for Q9 monitor only) from Programming PC. Below screen will display.
Fig-DDC1
Refer to Fig-DDC1; you have to select the required item if the display data was not you want. Press 1: For year, the cursor will move to the column behind “Edit Year” than you can key in
the data you want after that press enter to exit and return. (It needs 4 numbers for this data)
Press 2: For week, the cursor will move to the column behind “Edit Week” than you can key in
the data you want after that press enter to exit and return. (This data is within 1 ~ 53.)
Press 3: For S/N,, the cursor will move to the column behind “Edit S/N” than you can key in the
data you want after that press enter to exit and return. (This data is within 0 ~ 99999, 5 numbers max.)
28
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 32
D. Press “ESC” or “Enter” key to return main menu, the Fig-DDC2 will be displayed and the
correct serial number will show on right corner of screen.
Fig-DDC2
Under Fig-DDC2, you could change the “Week” data by press “*” key and the “S/N” data by press “­“ key.
Press 3 “DDC Writer/Check Data”: The Kit will start to program new data of EDID into monitor, all
DDC data will display on the screen after programming. Please refer to Fig-DDC3 below, the DDC process is finished.
Fig-DDC3
Display updated serial number.
29
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 33
The message (E2PROM Acknowledge Not Echo) will display on the screen if there is any error detected by Programming PC. If error message is happened, please re-check the connection of cable and return to first step.
Please refer to the Viewsonic EDID data format that was printing on ID label.
PPPYYWWAxxxx PPP = Viewsonic Regional Product ID Code, EX. Q9 is “PW1”, Q9b is “PW3”. YY= 2 digits of Manufacturing year. (range 1996-2015). WW = 2 digits of Manufacturing week (range 01-54). A = 0~1 HSD A grade + Realtek A = 2~3 HSD A- grade + Realtek A = 4~5 HSD V grade + Realtek A = 6~9 Reserve xxxx = 4 digits of Sequence number. (range 0001-9999).
30
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 34
5.4 Parking Procedure
1.1 Paste protecting film to protect the monitor. (Figure 1)
1.2 Put the montor in the PE bag and seal the bag with tape. (Figure 2)
Figure 1 Figure 2
1.3 Put the cushions on the monitor. (Figure 3)
1.4 Place the monitor into the carton and then put all the accessories into the carton. At last, The carton and seal it with tape. (Figure 4)
Figure 3 Figure 4
31
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 35
2. Disassembly
Lie down the monitor on flat table
Remove Stand by 4 screw
Remove CAB-B
Take off D-sub 2 screws
32
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 36
Remove the shielding case by 2 screws
Remove the I/F board
Remove the shielding case by 1 screw
Remove the Inverter board by 2 screws
33
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 37
6. TROUBLE SHOOTING FLOW CHART
Does picture
display?
YES
NO
Back-light On or off
Check Power
LED
A dark Picture or a Picture full Of colorfully vertical lines
Check Display
resolution
Check inverter Check I/F board JP1
Check I/F board JP9 Check panel connector
Check I/F board
OSD no respones too dim The brightness is
different between upper side and downer side
partly picture without color
Vertical,Horizontal none synchronousness
a few of colorfully vertical lines
even(or odd) vertical lines is dark
Check SW board
SW1 ~ SW4
Check OSD
adjustment
Check inverter of power board
Check backlight
Check I/F board
Check LCD panel
Check L
CD panel
Check I/F board
(DPWBN5625T89
-H-)
Check SW board JP1 Check inverter Check I/F board
OFF
ON
ON
Hsync
Vsync or DE error
Flash
RGB
Signal error
H,Vsync
error
34
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 38
CHK OSD U7 pin6,24,25 (PUSH KEY SWITCH)
CHK U7
pin 73~94
RETURN
DPWBN5625T8-CHA
Debug Procedure
JP1,
+12V&+5V
INPUT
Does the
screen
Display??
Solution with
No display
(2)
NO
Display
ok ?
YES
Lost some
bits
of RGB??
YES
NO
CHK R66(R ),
R63(G),R60(B)
C37C34C24
NO
35
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 39
CHK PWR
REF: power
flow
No display
(2)
Back-light
ok ?
NO
YES
U7
SCALER
INPUT/OUTPUT
D-SUB
VGA 15PIN
NO
CHK
JP9 INPUT
YES
CABLE
CHK Panel
CONNECTOR
YES
LED always ON
or always OFF
when power on
ok ?
CHK U5
SOCKET
SOFTWARE
KEY PAD
YES
CHK
JP1 PIN3、4
NO
CHK U5
Pin 19
CHK
SOFTWARE
OR
CHANGE U7
CHK
U1U2
NG
OK
YES
CHK LCD-VCC
CHK CLK
CHK R、G、B SIGNAL
NG
CHANGE Power board
FLASH
NORMAL
RETURN
OK
REPLACE
U1U2
NG
36
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 40
JP1, +5V
INPUT
CHK FUSE F1
CHK U1 input +5V U1 output +3.3V
CHK U2 input +3.3V U2 output +2.5V
DPWBN5625T89-H- POWER FLOW
Return
REPLACE U1
normal
abnormal
abnormal
REPLACE U2
37
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 41
Rev: 1a
Serial No Prefix: PW1
Panel Sources
Hanstarr
(12ms)
1
Accessories:
POWER CORD A-PC-0106-0180 QACC-1126D8D--- POWER CORD 1 2 AC ADAPTOR & INVERTER B-00003900 RUNTP5642T8---- ADAPTOR & INV. 1 3 I/F BOARD ASS'Y B-00003899 DPWBN5625T89-H- I/F BOARD ASS'Y 1 4 OSD-SW BOARD ASS'Y B-00003901 DPWBN5720T8---- SW BOARD ASS'Y 1 5 BASE C-00003935 GSTN-2940T8---- BASE 1 6 CAB-A C-00003936 GCABA2361T8F--E CAB-A 1 7 CAB-B C-00003937 DCABB1877T8F--A CAB-B 1 8 NECK C-00003938 GCOVD2613T8---- NECK 1 9 FFC CABLE (30 PIN) CB-00003907 QCODP1217T8---- FFC CABLE (30 PIN) 1
10 INVERTER EXTEND WIRE CB-00003906 QCNWS0902T8012- INV. EXTEND WIRE 2 11 OSD-SW WIRE CB-00003909 QCNWS0906T8033A OSD-SW WIRE 1 12 POWER BOARD GND WIRE CB-00003908 QTMLW0002-8376- POWER/B GND WIRE 2 13 SIGNAL CABLE CB-00002024 QCODS1584D8D--A SIGNAL CABLE 1 14 CD Wizard (CD-ROM) DC-00003939 DDSKC0063T8---- CD Wizard (CD-ROM) 1 15 ID LABEL DC-00003940 TLABM4495T8---- ID LABEL 1 16 Quick Start Guide DC-00003912 TINSE3206TG---- Quick Start Guide 1 17
30 PIN CONNECTOR
E-00003913
QCNCP2138T8----
30 PIN CONNECTOR
1
18 D-SUB CONNECTOR E-00003915 QCNCD1782T8---- D-SUB CONNECTOR 1 19
EEPROM
E-00001039
VSIMP24LC16B--A
EEPROM
1
20
FUSE 4A
E-FS-0410-0099
QFS-Z402F-81UAA
FUSE 4A
1
21 Hannstar PANEL (19") E-00003914 VVLHSD190ME12-2 Hanns. PANEL (19") 1 22
MCU
E-00001061
VSIMTV512MV---S
MCU
1
23 OSCILLATOR (24.000MHZ) E-00003916 RCRSL1173T8---- Y1 (24.000MHZ) 1 24 OSCILLATOR (24.576MHZ) E-00001063 RCRSL1252T8---- Y2 (24.576MHZ) 1 25
SCALER REALTEK
E-IC-0401-4040
VSIRTD2023----D
SCALER REALTEK
1
26 HINGE ASSEMBLY HW-00003920 MHNGM0062T8---- HINGE ASSEMBLY 1 27 I/F BOARD SHIELD HW-00003922 PSLDM6599T8---- I/F BOARD SHIELD 1 28 INVERTER SHIELD HW-00003921 PSLDM6597T8---- INVERTER SHIELD 1 29 MAIN METAL HW-00003923 LANGF2197T8---- MAIN METAL 1 30 PANEL METAL HW-00003918 LANGF2199T8---- PANEL METAL 1 31 PANEL METAL HW-00003919 LANGF2200T8---- PANEL METAL 1 32 PWB METAL HW-00003917 LANGF2198T8---- PWB METAL 1 33 BOSS FOR D-SUB M-MS-0808-5840 LBOSM1069D8---- BOSS FOR D-SUB 2 34 CUSHION FOR BASE M-00003925 GLEGG1478T8---- CUSHION FOR BASE 4 35 CUSHION FOR KNOB M-00003926 PCUSG1659T8---A CUSHION FOR KNOB 0.25 36 CUSHION-A M-00003927 PCUSG1671T8---- FOR PWB 1 37 CUSHION-B M-00003928 PCUSG1683T8---- FOR CAB-B 1 38 CUSHION-C M-00003929 PCUSG1680T8---- FOR PANEL 1 39 CUSHION-D M-00003930 PISLS1182D8---- FOR I/F SCREW 2 40 FOR SHIELDING CASE HW-00003924 LHLD-1467T8---- FOR SHIELDING CASE 3 41 CARTON P-00003931 SPAKC3714T8---D CARTON 1 42 PACKING P-00003932 SPAKA6615T8F--- PACKING 1 43 KNOB PL-00003941 JKNBP2388T8F--- KNOB 1 44 LENS PL-00003934 HDECP2005T8F--- LENS 1
Remark 1:
Remark 2:
Hardware:
Miscellaneous:
Packing Material:
All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved
by ViewSonic Corporation. This is to eliminate repeated cross checks of each item between this version and prior versions.
Item
Above listed items are examples, supplier can expand the rows to add more necessary items.
PC Board Assembly:
Cabinets:
Cables:
Documentation:
Plastics:
Electronic Components:
RECOMMENDED SPARE PARTS LIST (Q9-1)
ViewSonic Model Number: VS10863-1W
Description ECR/ECN ViewSonic P/N Ref. P/N Location
Universal Number#
7. Recommended Spare Parts List
38
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 42
Rev: 1a
Serial No Prefix: PW3
Panel Sources
Hanstarr
(12ms)
1
Accessories:
POWER CORD A-PC-0106-0180 QACC-1126D8D--- POWER CORD 1 2 AC ADAPTOR & INVERTER B-00003900 RUNTP5642T8---- ADAPTOR & INV. 1 3 I/F BOARD ASS'Y B-00003899 DPWBN5625T89-H- I/F BOARD ASS'Y 1 4 OSD-SW BOARD ASS'Y B-00003901 DPWBN5720T8---- SW BOARD ASS'Y 1 5 BASE C-00003903 GSTN-2940T8---A BASE 1 6 CAB-A C-00003904 GCABA2361T8F--F CAB-A 1 7 CAB-B C-00003905 DCABB1877T8F--D CAB-B 1 8 NECK C-00003902 GCOVD2613T8---A NECK 1 9 FFC CABLE (30 PIN) CB-00003907 QCODP1217T8---- FFC CABLE (30 PIN) 1
10 INVERTER EXTEND WIRE CB-00003906 QCNWS0902T8012- INV. EXTEND WIRE 2 11 OSD-SW WIRE CB-00003909 QCNWS0906T8033A OSD-SW WIRE 1 12 POWER BOARD GND WIRE CB-00003908 QTMLW0002-8376- POWER/B GND WIRE 2 13 SIGNAL CABLE CB-00002024 QCODS1584D8D--A SIGNAL CABLE 1 14 CD Wizard (CD-ROM) DC-00003910 DDSKC0064T8---- CD Wizard (CD-ROM) 1 15 ID LABEL DC-00003911 TLABM4496T8---- ID LABEL 1 16 Quick Start Guide DC-00003912 TINSE3206TG---- Quick Start Guide 1 17
30 PIN CONNECTOR
E-00003913 QCNCP2138T8----
30 PIN CONNECTOR
1 18 D-SUB CONNECTOR E-00003915 QCNCD1782T8---- D-SUB CONNECTOR 1 19
EEPROM
E-00001039 VSIMP24LC16B--A
EEPROM
1 20
FUSE 4A
E-FS-0410-0099 QFS-Z402F-81UAA
FUSE 4A
1 21 Hannstar PANEL (19") E-00003914 VVLHSD190ME12-2 Hanns. PANEL (19") 1 22
MCU
E-00001061 VSIMTV512MV---S
MCU
1 23 OSCILLATOR (24.000MHZ) E-00003916 RCRSL1173T8---- Y1 (24.000MHZ) 1 24 OSCILLATOR (24.576MHZ) E-00001063 RCRSL1252T8---- Y2 (24.576MHZ) 1 25
SCALER REALTEK
E-IC-0401-4040 VSIRTD2023----D
SCALER REALTEK
1 26 HINGE ASSEMBLY HW-00003920 MHNGM0062T8---- HINGE ASSEMBLY 1 27 I/F BOARD SHIELD HW-00003922 PSLDM6599T8---- I/F BOARD SHIELD 1 28 INVERTER SHIELD HW-00003921 PSLDM6597T8---- INVERTER SHIELD 1 29 MAIN METAL HW-00003923 LANGF2197T8---- MAIN METAL 1 30 PANEL METAL HW-00003918 LANGF2199T8---- PANEL METAL 1 31 PANEL METAL HW-00003919 LANGF2200T8---- PANEL METAL 1 32 PWB METAL HW-00003917 LANGF2198T8---- PWB METAL 1 33 BOSS FOR D-SUB M-MS-0808-5840 LBOSM1069D8---- BOSS FOR D-SUB 2 34 CUSHION FOR BASE M-00003925 GLEGG1478T8---- CUSHION FOR BASE 4 35 CUSHION FOR KNOB M-00003926 PCUSG1659T8---A CUSHION FOR KNOB 0.25 36 CUSHION-A M-00003927 PCUSG1671T8---- FOR PWB 1 37 CUSHION-B M-00003928 PCUSG1683T8---- FOR CAB-B 1 38 CUSHION-C M-00003929 PCUSG1680T8---- FOR PANEL 1 39 CUSHION-D M-00003930 PISLS1182D8---- FOR I/F SCREW 2 40 FOR SHIELDING CASE HW-00003924 LHLD-1467T8---- FOR SHIELDING CASE 3 41 CARTON P-00003931 SPAKC3714T8---D CARTON 1 42 PACKING P-00003932 SPAKA6615T8F--- PACKING 1 43 KNOB PL-00003933 JKNBP2388T8F--B KNOB 1 44 LENS PL-00003934 HDECP2005T8F--- LENS 1
Remark 1:
Remark 2:
Hardware:
Miscellaneous:
Packing Material:
All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR
Item
Above listed items are examples, supplier can expand the rows to add more necessary items.
PC Board Assembly:
Cabinets:
Cables:
Documentation:
Plastics:
Electronic Components:
RECOMMENDED SPARE PARTS LIST (Q9b-1)
ViewSonic Model Number: VS10863-1W
Description ECR/ECN ViewSonic P/N Ref. P/N Location
Universal Number#
39
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 43
Rev: 1a
Serial No Prefix: PW1
Item
ViewSonic P/N
Ref. P/N
Description
Location
Universal number#
Q'ty
1 CB-00003908 QTMLW0002-8376- POWER BOARD GND WIRE POWER BOARD GND WIRE 2 2
C-00003935 GSTN-2940T8---- BASE BASE 1
3
C-00003938 GCOVD2613T8---- NECK NECK 1
4
M-00003925 GLEGG1478T8---- BASE*4 BASE*4 4
5
HW-00003920 MHNGM0062T8---- HINGE HINGE 1
6
#N/A XEASD35P12000-- HINGE/NECK*6 HINGE/NECK*6 6
7
#N/A XBSSB40P08000-A HINGE/CAB-B*4 HINGE/CAB-B*4 4
8
C-00003936 GCABA2361T8F--E CAB-A CAB-A 1
9
C-00003937 DCABB1877T8F--A CAB-B ASM CAB-B ASM 1
10
PL-00003941 JKNBP2388T8F--- KNOB KNOB 1
11
PL-00003934 HDECP2005T8F--- LENS LENS 1
12
M-MS-0808-5840 LBOSM1069D8---- VGA BOSS VGA BOSS 2
13
M-SCW-0824-0464 XETSD40P10000-- CAB-A/CHASSIS*2 CAB-A/CHASSIS*2 2
14
M-SCW-0824-6739 XBMSD40P08TV0-- GROUND*1 GROUND*1 1
15
B-00003901 DPWBN5720T8---- KEY BOARD ASS'Y KEY BOARD ASS'Y 1
16
CB-00003909 QCNWS0906T8033A KEY BOARD WIRE KEY BOARD WIRE 1
17
M-00003926 PCUSG1659T8---A KNOB USE KNOB USE 0.25
18
#N/A TLABZ4916T8---- HIGH VOLTAGE LABEL HIGH VOLTAGE LABEL 1
19
DC-00003912 TINSE3206TG---- USER'S MANUAL USER'S MANUAL 1
20
M-LB-0813-0527 TLABZ3903D8---- UPC LABEL UPC LABEL 1
21
M-MS-0808-8408 PISL-1281D8---- PROTECT SHEET PROTECT SHEET 1
22
#N/A SPAKW1260T8---- PALLET PALLET 0.02
23
#N/A SSAKH1356D8-T-B SET BAG SET BAG 1
24
#N/A SSAKD0010-1-T-- BAG BAG 1
25
#N/A SPAKK6309D8---- COVER PAPER COVER PAPER 0.12
26
#N/A ZTAPEQ072T050-B TAPE FOR CARTON TAPE FOR CARTON 1.2
27
DC-00003940 TLABM4495T8---- ID LABEL ID LABEL 1
28
P-00003932 SPAKA6615T8F--- PACKING FOAM PACKING FOAM 1
29
P-00003931 SPAKC3714T8---D CARTON CARTON 1
30
A-PC-0106-0180 QACC-1126D8D--- AC POWER CORD(1.8M) AC POWER CORD(1.8M) 1
31
CB-00002024 QCODS1584D8D--A SIGNAL CABLE (1.8M BLACK) SIGNAL CABLE (1.8M BLACK) 1
32
DC-00003939 DDSKC0063T8---- CD-DRIVE CD-DRIVE 1
33
#N/A ZTAPEY010G060-- TYPE FOR PROTECT SHEET TYPE FOR PROTECT SHEET 80
34
#N/A TLAB-5523D8---- S/N LABEL S/N LABEL 1
35
#N/A TLAB-5657T8---- HI-POT PASS LABEL HI-POT PASS LABEL 1
BOM LIST
CPWB-Q9--T8HSD-
Item
ViewSonic P/N
Ref. P/N
Description
Location
Universal number#
Q'ty
1 E-00003914 VVLHSD190ME12-2 HSD 19" PANEL (12ms) HSD 19" PANEL (12ms) 1 2
#N/A VVLHSD190ME12N2 2nd 1
3
#N/A VVLHSD190ME12V2 2nd 1
4
B-00003900 RUNTP5642T8---- AC ADAPTOR & INVERTER AC ADAPTOR & INVERTER 1
5
#N/A RUNTP5651T8---- 2nd 1
6
B-00003899 DPWBN5625T89-H- I/F BOARD ASS'Y I/F BOARD ASS'Y 1
7
CB-00003907 QCODP1217T8---- LVDS(FFC) CABLE LVDS(FFC) CABLE 1
8
CB-00003906 QCNWS0902T8012- INVERTER EXTEND WIRE INVERTER EXTEND WIRE 2
9
HW-00003923 LANGF2197T8---- CHASSIS CHASSIS 1
10
HW-00003917 LANGF2198T8---- PWB USE PWB USE 1
11
HW-00003918 LANGF2199T8---- PANEL USE PANEL USE 1
12
HW-00003919 LANGF2200T8---- PANEL USE PANEL USE 1
13
M-SCW-0824-6733 XBMSD30P06000-- LANGF2198/PWB*2 LANGF2198/PWB*2 2
14
HW-00003921 PSLDM6597T8---- SHIELDING CASE SHIELDING CASE 1
15
HW-00003924 LHLD-1467T8---- SHIELDING CASE USE SHIELDING CASE USE 3
16
#N/A XBSSE30P06000-- PANEL/LANGF2199*1,CHASSIS*1 PANEL/LANGF2199*1,CHASSIS*1 2
17
M-SCW-0824-0463 XEASD30P10000-- CAB-A/LANGF2199*1,LANGF2200*1 CAB-A/LANGF2199*1,LANGF2200*1 2
18
M-00003927 PCUSG1671T8---- PWB USE PWB USE 1
19
#N/A ZTAPEL040S030-- 40MM*1,50MM*2,60MM*1 40MM*1,50MM*2,60MM*1 200
20
#N/A ZTAPEL025S030-- 50MM*2 50MM*2 100
21
#N/A ZTAPEY020W066U- 50MM*3,70MM*1 50MM*3,70MM*1 220
#N/A
LANGF2198/PSLDM6597*1,CHASSIS*4,PANEL LANGF2198/PSLDM6597*1,CHASSIS*4,PANEL /LANGF2200*1
/LANGF2200*1
23
#N/A XBJSD30P04000-- LANGF2198/PWB*2 LANGF2198/PWB*2 2
24
HW-00003922 PSLDM6599T8---- I/F BOARD SHIELDING CASE I/F BOARD SHIELDING CASE 1
25
M-00003928 PCUSG1683T8---- CAB-B*2 CAB-B*2 2
26
M-00003929 PCUSG1680T8---- HT PANEL USE HT PANEL USE 1
27 M-00003930 PISLS1182D8---- FOR I/F BOARD SCREW FOR I/F BOARD SCREW 2
BOM LIST
DCABB1877T8F--A
Item
ViewSonic P/N
Ref. P/N
Description
Location
Universal number#
Q'ty
1 #N/A GCABB1877T8F--A CAB-A CAB-A 1 2 #N/A LANGF2194T8---- VESA METAL VESA METAL 4
ViewSonic Model Number: VS10863-1W
BOM LIST (Q9-1)
22 XBJSD30P08000-- 6
40
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 44
Rev: 1a
Serial No Prefix: PW3
Item
ViewSonic P/N
Ref. P/N
Description
Location
Universal number#
Q'ty
1
CB-00003908
QTMLW0002-8376-
POWER BOARD GND WIRE
POWER BOARD GND WIRE
2
2
C-00003903
GSTN-2940T8---A
BASE
BASE
1
3
C-00003902
GCOVD2613T8---A
NECK
NECK
1
4
M-00003925
GLEGG1478T8----
BASE*4
BASE*4
4
5
HW-00003920
MHNGM0062T8----
HINGE
HINGE
1
6
#N/A
XEASD35P12000--
HINGE/NECK*6
HINGE/NECK*6
6
7
#N/A
XBSSB40P08000-A
HINGE/CAB-B*4
HINGE/CAB-B*4
4
8
C-00003904
GCABA2361T8F--F
CAB-A
CAB-A
1
9
C-00003905
DCABB1877T8F--D
CAB-B ASM
CAB-B ASM
1
10
PL-00003933
JKNBP2388T8F--B
KNOB
KNOB
1
11
PL-00003934
HDECP2005T8F---
LENS
LENS
1
12
M-MS-0808-5840
LBOSM1069D8----
VGA BOSS
VGA BOSS
2
13
M-SCW-0824-0464
XETSD40P10000--
CAB-A/CHASSIS*2
CAB-A/CHASSIS*2
2
14
M-SCW-0824-6739
XBMSD40P08TV0--
GROUND*1
GROUND*1
1
15
B-00003901
DPWBN5720T8----
KEY BOARD ASS'Y
KEY BOARD ASS'Y
1
16
CB-00003909
QCNWS0906T8033A
KEY BOARD WIRE
KEY BOARD WIRE
1
17
M-00003926
PCUSG1659T8---A
KNOB USE
KNOB USE
0.25
18
#N/A
TLABZ4916T8----
HIGH VOLTAGE LABEL
HIGH VOLTAGE LABEL
1
19
DC-00003912
TINSE3206TG----
USER'S MANUAL
USER'S MANUAL
1
20
M-LB-0813-0527
TLABZ3903D8----
UPC LABEL
UPC LABEL
2
21
M-MS-0808-8408
PISL-1281D8----
PROTECT SHEET
PROTECT SHEET
1
22
#N/A
SPAKW1260T8----
PALLET
PALLET
0.02
23
#N/A
SSAKH1356D8-T-B
SET BAG
SET BAG
1
24
#N/A
SSAKD0010-1-T--
BAG
BAG
1
25
#N/A
SPAKK6309D8----
COVER PAPER
COVER PAPER
0.12
26
#N/A
ZTAPEQ072T050-B
TAPE FOR CARTON
TAPE FOR CARTON
1.2
27
DC-00003911
TLABM4496T8----
ID LABEL
ID LABEL
1
28
P-00003932
SPAKA6615T8F---
PACKING FOAM
PACKING FOAM
1
29
P-00003931
SPAKC3714T8---D
CARTON
CARTON
1
30
A-PC-0106-0180
QACC-1126D8D---
AC POWER CORD(1.8M)
AC POWER CORD(1.8M)
1
31
CB-00002024
QCODS1584D8D--A
SIGNAL CABLE (1.8M BLACK)
SIGNAL CABLE (1.8M BLACK)
1
32
DC-00003910
DDSKC0064T8----
CD-DRIVE
CD-DRIVE
1
33
#N/A
ZTAPEY010G060--
TYPE FOR PROTECT SHEET
TYPE FOR PROTECT SHEET
80
34
#N/A
TLAB-5523D8----
S/N LABEL
S/N LABEL
1
35
#N/A
TLAB-5657T8----
HI-POT PASS LABEL
HI-POT PASS LABEL
1
BOM LIST
CPWB-Q9--T8HSD-
Item
ViewSonic P/N
Ref. P/N
Description
Location
Universal number#
Q'ty
1
E-00003914
VVLHSD190ME12-2
HSD 19" PANEL (12ms)
HSD 19" PANEL (12ms)
1
2
#N/A
VVLHSD190ME12N2 2nd
1
3
#N/A
VVLHSD190ME12V2 2nd
1
4
B-00003900
RUNTP5642T8----
AC ADAPTOR & INVERTER
AC ADAPTOR & INVERTER
1
5
#N/A
RUNTP5651T8---- 2nd
1
6
B-00003899
DPWBN5625T89-H-
I/F BOARD ASS'Y
I/F BOARD ASS'Y
1
7
CB-00003907
QCODP1217T8----
LVDS(FFC) CABLE
LVDS(FFC) CABLE
1
8
CB-00003906
QCNWS0902T8012-
INVERTER EXTEND WIRE
INVERTER EXTEND WIRE
2
9
HW-00003923
LANGF2197T8----
CHASSIS
CHASSIS
1
10
HW-00003917
LANGF2198T8----
PWB USE
PWB USE
1
11
HW-00003918
LANGF2199T8----
PANEL USE
PANEL USE
1
12
HW-00003919
LANGF2200T8----
PANEL USE
PANEL USE
1
13
M-SCW-0824-6733
XBMSD30P06000--
LANGF2198/PWB*2
LANGF2198/PWB*2
2
14
HW-00003921
PSLDM6597T8----
SHIELDING CASE
SHIELDING CASE
1
15
HW-00003924
LHLD-1467T8----
SHIELDING CASE USE
SHIELDING CASE USE
3
16
#N/A
XBSSE30P06000--
PANEL/LANGF2199*1,CHASSIS*1
PANEL/LANGF2199*1,CHASSIS*1
2
17
M-SCW-0824-0463
XEASD30P10000--
CAB-A/LANGF2199*1,LANGF2200*1
CAB-A/LANGF2199*1,LANGF2200*1
2
18
M-00003927
PCUSG1671T8----
PWB USE
PWB USE
1
19
#N/A
ZTAPEL040S030--
40MM*1,50MM*2,60MM*1
40MM*1,50MM*2,60MM*1
200
20
#N/A
ZTAPEL025S030--
50MM*2
50MM*2
100
21
#N/A
ZTAPEY020W066U-
50MM*3,70MM*1
50MM*3,70MM*1
220
LANGF2198/PSLDM6597*1,CHASSIS*4,PANEL
LANGF2198/PSLDM6597*1,CHASSIS*4,PANEL
/LANGF2200*1
/LANGF2200*1
23
#N/A
XBJSD30P04000--
LANGF2198/PWB*2
LANGF2198/PWB*2
2
24
HW-00003922
PSLDM6599T8----
I/F BOARD SHIELDING CASE
I/F BOARD SHIELDING CASE
1
25
M-00003928
PCUSG1683T8----
CAB-B*2
CAB-B*2
2
26
M-00003929
PCUSG1680T8----
HT PANEL USE
HT PANEL USE
1
27
M-00003930
PISLS1182D8----
FOR I/F BOARD SCREW
FOR I/F BOARD SCREW
2
BOM LIST
DCABB1877T8F--A
Item
ViewSonic P/N
Ref. P/N
Description
Location
Universal number#
Q'ty
1
#N/A
GCABB1877T8F--A
CAB-A
CAB-A
1
2
#N/A
LANGF2194T8----
VESA METAL
VESA METAL
4
ViewSonic Model Number: VS10863-1W
BOM LIST (Q9b-1)
22 M-SCW-0824-6733 XBJSD30P08000-- 6
41
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 45
8. Exploded Diagram And Spare Parts List
42
ViewSonic Corporation Confidential - Do Not Copy Q9-1_Q9b-1
ViewSonic Model Number: VS10863-1W Rev: 1a
Serial No. Prefix: PW1
Item
ViewSonic P/N
Ref. P/N
Description
Q'ty
1 C-00003936 GCABA2361T8F--E CAB-A 1 2 HW-00003918 LANGF2199T8---- PANEL USE 1 3 #N/A VVLHSD190ME12-- HANNSTAR 19" PANEL 1 4 HW-00003923 LANGF2197T8---- CHASSIS 1 5 HW-00003919 LANGF2200T8---- PANEL USE 1 6 HW-00003922 PSLDM6599T8---- I/F BOARD SHIELDING CASE 1 7 B-00003899 DPWBN5625T89-H- I/F BOARD 1 8 M-00003927 PCUSG1671T8---- PWB USE 1
9 B-00003900 RUNTP5642T8---- AC ADAPTOR & INVERTER 1 10 C-00003937 DCABB1877T8F--A CAB-B ASM 1 11 #N/A LANGF2194T8---- VESA METAL 4 12 HW-00003924 LHLD-1467T8---- SHIELDING CASE USE 3 13 HW-00003921 PSLDM6597T8---- SHIELDING CASE 1 14 #N/A MHNGM0062T8---B HINGE 1 15 C-00003938 GCOVD2613T8---- NECK 1 16 C-00003935 GSTN-2940T8---- BASE 1 17 M-00003925 GLEGG1478T8---- BASE*4 4 18 HW-00003917 LANGF2198T8---- PWB USE 1 19 PL-00003941 JKNBP2388T8F--- KNOB 1 20 B-00003901 DPWBN5720T8---- KEY BOARD ASS'Y 1
21
PL-00003934
HDECP2005T8F---
LENS
1
EXPLODED PARTS LIST (Q9-1)
ViewSonic Model Number: VS10863-1W Rev: 1a
Serial No. Prefix: PW3
Item
ViewSonic P/N
Ref. P/N
Description
Q'ty
1 C-00003904 GCABA2361T8F--F CAB-A 1
2 HW-00003918 LANGF2199T8---- PANEL USE 1
3 #N/A VVLHSD190ME12-- HANNSTAR 19" PANEL 1
4 HW-00003923 LANGF2197T8---- CHASSIS 1
5 HW-00003919 LANGF2200T8---- PANEL USE 1
6 HW-00003922 PSLDM6599T8---- I/F BOARD SHIELDING CASE 1
7 B-00003899 DPWBN5625T89-H- I/F BOARD 1
8 M-00003927 PCUSG1671T8---- PWB USE 1
9 B-00003900 RUNTP5642T8---- AC ADAPTOR & INVERTER 1 10 C-00003905 DCABB1877T8F--D CAB-B ASM 1 11 #N/A LANGF2194T8---- VESA METAL 4 12 HW-00003924 LHLD-1467T8---- SHIELDING CASE USE 3 13 HW-00003921 PSLDM6597T8---- SHIELDING CASE 1 14 #N/A MHNGM0062T8---B HINGE 1 15 C-00003902 GCOVD2613T8---A NECK 1 16 C-00003903 GSTN-2940T8---A BASE 1 17 M-00003925 GLEGG1478T8---- BASE*4 4 18 HW-00003917 LANGF2198T8---- PWB USE 1 19 PL-00003933 JKNBP2388T8F--B KNOB 1 20 B-00003901 DPWBN5720T8---- KEY BOARD ASS'Y 1
21
PL-00003934
HDECP2005T8F---
LENS
1
EXPLODED PARTS LIST (Q9b-1)
Page 46
43
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 47
9. Block Diagram
JP7
(DB15)
COMPUTER
GRAPHICS
U7 Realtek
RTD2023
SERIAL
EEPROM
MPU
U5
MTV512MV
INTERFACE BOARD ( DPWBN5625T89-H- )
JP1
To Inverter &
DC input
5V,
12V
POWER SUPPLY
AC Input
90-240V 50/60Hz
19” LCD PANEL
3.3V
5V
SW BOARD
DPWBN5720T8----
JP6
SCALER
Adapter & Inverter
RUNTP5642T8----
CON10
C
O N N E C T O R
U6
EEPROM
24C16
Y1
OSC
JP9
30 PIN
LVDS CABLE
CON103,CON104
CON105,CON106
Y2
OSC
CON001
DDC
EEPROM
2.5V
Backlight control
JP4
Backlight control
DC output +5V & +12V
44
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 48
JST PHR-13
2.0 pitch 90 Degree
serial
Pin 27, 29, 40, 41
的電容請盡IC量靠近
Change Value
VGAVS
VGAHS
CB
VGA_G
CG-
CR
CB-
VGA_B
VGA_R
CR-
CGSOG_in
RXO1-
RXE3-
RXO0+
RXE2-
DGND
LCD_VCC
RXO1+
RXO3+
RXE2+
RXE3+
RXE0-
LCD_VCC
RXEC-
RXE1-
RXOC-
RXE0+
RXOC+
RXEC+
RXE1+
DGND
DGND
RXO3-
DGND
RXO0-
RXO2­RXO2+
LCD_VCC
VGA_R VGA_G
VGA_B
VGA5V CONNECT
VSIN HSIN
VGA_B­VGA_B VGA_G­VGA_G VGA_R­VGA_R
HSIN
RXO3-
RXE3-
RXO2-
RXO3+
RXE2-
RXO1+
RXE0-
RXO1-
RXE3+
RXO0+
RXE0+
RXE1-
RXE1+
RXO2+
RXO0-
RXE2+
RTD_SCLK
RTD_RESET
RTD_SDO/SDI RTD_SCSB
PLL_TEST2
CG-
VGAVS
CB
CR-
CG
CB-
VGAHS
CR
SOG_in
RXEC+
RXOC-
RXOC+
VSIN
HSIN
VSIN
DDC_SDA
VGA_G
VGA_R
VGA_B
DDC_SCL
VGA_R-
VGA_B-
VGA_G-
VGA_R-
VGA_G-
VGA_B-
RXEC-
DDC_SDA
DDC_SCL
RXO2+
RXE2-
LCD_VCC
RXE2+
RXOC+
RXE3+
DGND
RXO2-
RXO1-
RXO3+
RXO0+
RXE1+
RXE3-
RXO0-
LCD_VCC
RXOC-
RXE0+
LCD_VCC
RXEC+
RXEC-
RXO1+
RXE0-
RXO3-
RXE1-
DGND
PANEL_5VCC
3DVCC
DDC_SCL DDC_SDA
Brightness
RTD_SDO/SDI
3AVCC1
3PVCC
VGA5V
VSIN
CONNECT
VOLUME XOUT
RTD_SCLK
RTD_SCSB RTD_RESET
ADC_VCC ADC_VCC ADC_VCC
R3DVCC3DVCC
2.5DVCC
R3DVCC
ADC_VCC
3AVCC1
3PVCC
3AVCC1
3AVCC1
D4 BAV99_SOT
3
1
2
+
C49
22uF_16V
L7 FEB_0603 19ohm
L5 FEB_0603 19ohm
L3 FEB_0603 19ohm
L10 FEB_0805
R97
10K
R69 NC/1M
R71 1K
R83 10K
D5 BAV99_SOT
3
1
2
R62 100
D6 BAV99_SOT
3
1
2
C33 47nF
C55 22pF
C56 22pF
R75 NC
RTD2023
113946
47
5450111
56
42 43
114 115 116 117 118 119 122 123 124
31
30
33
34
38
39
37
29
32
28
27
6 7
1
2
4
3
58
57
5
8
120
1214948
70
128
44459869127
109
110
112
26
25
15
14
19 17 18 22
13 20 21 16
11 23 24 10
12
126
125
73 74
75 76
77 78
79 80
81 82
85 86
87 88
89 90
91 92
93 94
72
96
71
95
36
35
83
84
596061626364656667
68
103
104
105
106
107
108
97
40
41
515253
55
99
100
101
102
TCON[12]/COOUT/PWM2
TMDS_TST/PWM1
DDC_SCL
DDC_SDA
SDIO
SCLK
SCSB
RESET#
AHS AVS
V0 V1 V2 V3 V4 V5 V6 V7 VCLK
B-
B+
SOG
G+
R-
ADC_GND
R+
ADC_VDD
ADC_GND
ADC_REFIO
ADC_GND
PLL_TEST1 PLL_TEST2
XO
XI
DPLL_VDD
DPLL_GND
PVCC
PGND
APLL_VDD
APLL_GND
GNDIO
VCCIO
VCCIO
GNDIO
GNDK
GNDK
GNDK
VCCK
VCCK
VCCK
VCCK
PGND
PVCC
REFCLK/PWM0
TMDS_VDD
TMDS_GND
RX2N
RX2P
TMDS_VDD
RX1P RX1N
TMDS_GND
TMDS_VDD
RX0P RX0N
TMDS_GND
TMDS_VDD
RXCP RXCN
TMDS_GND
REXT
DDC2_SCL
DDC2_SDA
TODP TODN
TOCLKP TOCLKN
TOCP TOCN
TOBP TOBN
TOAP TOAN
TEDP TEDN
TECLKP TECLKN
TECP TECN
TEBP TEBN
TEAP TEAN
PGND
PGND
PVCC
PVCC
ADC_VDD
G-
PVCC
PGND
BB3P
BB3N
BB2P
BB2N
BB1P
BB1N
BCLKP
BCLKN
BG3P
BBG3N
AR3P
AR3N
AR2P
AR2N
AR1P
AR1N
GNDK
ADC_GND
ADC_VDD
TCON[2]/SDIO[3]/PWM2
TCON[3]/SDIO[2]
TCON[4]/SDIO[1]
TCON[13]/COUT/PWM2
AG2P
AG2N
AG1P
AG1N
L8 0
R
G
B
NC
DGND
RAGND
GAGND
BAGND
VGA5V
DGND
NC
DDCSDA
DDCSCL
HSIN
VSIN
JP7
VGA_CON15
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
C34 47nF
C24 47nF
R61 75
R68 75
C37 47nF
C38 NC/47nF
JP9
CON30
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
R60 100
R66 100
R63 100
R64 75
JP10
CON13
1 2 3 4 5 6 7 8
9 10 11 12 13
R67 NC/100
Y2
24.576MHz
R74 10K
R89 NC
R86 NC
L2 FEB_0805
+
C25
22uF_16V
C45 100nF
D11
5.6V
C46 100nF
L9 FEB_0805
C47 100nF
+
C43
22uF_16V
R79 2K
C57 22pF
R77 100
C26 100nF
C27 100nF
R78 2K
R76 100ohm or 1.2nH
C58 12pF
C30 100nF
C29 100nF
C31 100nF
C48 100nF
C28 100nF
C61 100nF
D8
5.6V
C44 100nF
ZD1
5.6V
1
2
C63 100nF
ZD2
5.6V
1
2
D10
5.6V
C42 100nF
C64 100nF
C65 100nF
D7
5.6V
C32 5pF
C39 5pF
C35 5pF
JP8
CONN RECT 15x2
25 23 21 19 17 15 13 11 9 7 5 3 1
26 24 22 20 18 16 14 12 10
8 6 4 2
2728
2930
25 23 21 19 17 15 13 11
9 7 5 3 1
26 24 22 20 18 16 14 12 10 8 6 4 2
2728
2930
C36 47nFR65 100
L4 0
NCR92
L6 0
C62 100nF
C52 100nF
C51 100nF
C41 100nF
C40 47nFR70 100
10. Schematic Diagrams
Model
Title
Date Rev:
ViewSonic Corporation
45
ViewSonic Corporation Confidential - Do Not Copy Q9-1_Q9b-1
RTD2030
Page 49
2.0mm 6pin
0805
R93 Same D3 location
MODIFY20050225
MODIFY20050225
LED_O
VSIN
IICSDA
LED_G
DDC_SDA
IICSCL
SELECT_KEY
RTD_RESET
IICSDA
RTD_SDO/SDI
VGA5V
RTD_SCSB
MENU_KEY SELECT_KEY
3MCUVCC
3MCUVCC
PROFPNL
BACKLIGHT
POWER_KEY
3MCUVCC
DDC_SCL
RTD_RESET
RTD_SCLK
IICSCL
MENU_KEY
SRS
CONNECT
MUTE Audio_EN
POWER_KEY
LED_O
3MCUVCC
3MCUVCC
LED_G
XOUT
MCU_VCC
MCU_VCC
MCU_VCC
MCU_VCC
MCU_VCC
MCU_VCC
+5V
R103 100
Q6 MMBT3906
1
2
3
R34
4.7K
R29
4.7K
R47NCR46
NC
D2
1N4148
D1
1N4148
R101
47K
R27 NC
R43
4.7K
R100 1M
R22
4.7K
R21
4.7K C18 100nF
R33 100
R28 NC
R35 100
R55 6.8K
Y1
24MHz
R93 0
C22 10pF
C23 10pF
R17 10K
Q8 2N3906
1
2
3
R44
4.7K
ZD4
5.6V
1
2
R26 10K
ZD5
5.6V
1
2
JP6
CON6
1 2 3 4 5 6
R94 4.7K
C73 100nF
C20 1uF
R98
330
R52 1K
D3
NC/DAN202U
3
2
1
C72 100nF
R99
330
C71 100nF
R24 10K
R45 0
R23 10K
R25 10K
Q7 2N3906
1
2
3
R96
10K
ZD6
5.6V
1
2
R95 4.7K
R42
4.7K
R41
4.7K
R50 10K
R40
4.7K R39
4.7K
R38
4.7K
R51 1K
U6
24C16_SMD
8 5 6 4
7 3 2 1
5DVCC SDA SCL GND
TEST
A2 A1 A0
R58 100
C21 100nF
R57 100
ZD3 NC / 3.3V
1
2
Q5 MMBT3906
1
2
3
R49
4.7K
R48
4.7K
R32 100K
MTV512
U5 MTV512
2 3 4 5 6 7 8 9
10
13
20
21
22
44
43
42
41
40
39
38
37
36
35
32
33
24
25
26
27
28
29
30
31
11
14 15 16 17 18 19
12
P5.0/DA0 P5.1/DA1 P5.2/DA2 P5.3/DA3 P5.4/DA4 P5.5/DA5 HSCL2/P5.6 HSDA2/P5.7
RST
HDA1/TX/P3.1
XTAL2
XTAL1
VSS
VCC
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
NC
VSYNC
NC
P6.0/AD0
P6.1/AD1
P6.2/AD2
P6.3/AD3
P6.4
P6.5
P6.6/CLK0
P6.7
HCL1/RX/P3.0
P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 P7.6/CLKO P7.7
NC
R30 NC
R102 100
Model
Title
Date Rev:
ViewSonic Corporation
MCU
46
ViewSonic Corporation Confidential - Do Not Copy Q9-1_Q9b-1
Page 50
MCU 3VCC RTD 3DVCC
RTD 3PVCC
ADC_ 3AVCC
JST PHR-8
2.0 pitch 90 Degree
2.
雙排側插
0
pitch, 2*4
JST PHR-5
2.0 pitch 90 Degree
0805
0805
BL_ADJ
BL_ON_OFF
PANEL_5VCC
BL_ON_OFF BL_ADJ
PROFPNL
Brightness
BACKLIGHT
PANEL_5VCC
3PVCC
3AVCC1
3DVCC
3MCUVCC
SRS
Audio_EN
VOLUME
MUTE
+5V +5V
+5V
+5V
+5V
+5V +5V
C_12V
+12V
C_12V
+12V
2.5DVCC
JP3
CON5
1 2 3 4 5
C15 100nF(0805)
R13
4.7K
R12 10K
C3 NC / 100nF
C16 100nF
+
C14
100uF_16V
C10 1uF
C17 100nF
JP2
CON8A
1 3 5 7
2 4 6 8
C13 100nF
U4
FDS9435
1 2 3 4
5
6
7
8
S S S GD
D
D
D
R16 100
+
C11
100uF_16V
C9 100nF
R7 220
R8 22
Q2
2N3904
1
2
3
R5
4.7K
R15 NC
R6 20K
C6 1uF
R4 2K
C8 100nF
Q1 2N3904
1
2
3
R10 100K
C12 100nF
+
C4
22uF_16V
Q3 2N3904
1
2
3
+
C2
100uF_16V
+
C1
100uF_16V
U1 GM1117CY_3.3
3
1
2
VIN
GND
VOUT
U2 GM1117CY_2.5
3
1
2
VIN
GND
VOUT
R11
4.7K
R14 1K
F1 4A_SMD
JP4
CON2
1 2
JP5
CON2
1 2
U3
FDS9435
1 2 3 4
5
6
7
8
S S S GD
D
D
D
JP1
CON8
1 2 3 4 5 6 7 8
L1 RFIL-5240T8110A[1206]
R2 0
R1 NC/124 1%
Q4
MMBT3906
1
2
3
R3 NC/200 1%
R9 0
C5 100nF
C7 NC / 100nF
Model
Title
Date Rev:
ViewSonic Corporation
POWER
47
ViewSonic Corporation Confidential - Do Not Copy Q9-1_Q9b-1
Page 51
C4
100p
C1
100p
C2
100p
C3
100p
R1
2.2K
R2 100R
R5 100R
JP1
CON6
6 5 4 3 2 1
R7 100R
L5
0
R3
4.7K
R4
4.7K
R6
2.2K
D3
5.6V
L2
0
LED1
1
2
L4
0
L3
0
L1
0
SW1
MENU
3
1
SW5
POWER SW
3
1
SW3
-
3
1
SW4
+
3
1
SW2
SELECT
3
1
SW1__MENU
SW3_UP_DOWN
SOFT_START
LED_GRN
SW1__MENU
SOFT_START
LED_GRN
SW3_UP_DOWN
Model
Title
Date Rev:
ViewSonic Corporation
KeyBoard
48
ViewSonic Corporation Confidential - Do Not Copy Q9-1_Q9b-1
Page 52
11. PCB Layout Diagrams
IF-board
49
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 53
50
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 54
51
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 55
52
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 56
53
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 57
54
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 58
55
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 59
56
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 60
Key-board
SOLDER
57
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 61
DRILL
58
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 62
COMP SILK
59
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 63
Top
60
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 64
SOLDERMASK
61
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 65
Top Mask
62
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Page 66
*Readers Response*
Dear Readers:
Thank you in advance for your feedback on our Service Manual, which allows continuous improvement
of our products. We would appreciate your completion of the Assessment Matrix below, for return to
ViewSonic Corporation.
Assessment
Readers basic data:
After completing this form, please return it to ViewSonic Quality Assurance
metI tnellecxE dooG riaF daB
.1
.2
.3
tinU riaF daB
in the USA at facsimile
1-909-839-7943.
You may also e-mail any suggestions to the Director, Quality Systems & Processes
(marc.maupin@viewsonic.com)
dooGtnellecxE
Precautions and Safety Notices
1.
8. Exploded Diagram and Exploded Parts List
7. Recommended Spare Parts List
Adjustment Procedure
2. Specification
5.
4. Circuit Description
3.
6. Troubleshooting Flow Chart
Front Panel Function Control Description
9. Block Diagram
10. Schematic Diagrams
11. PCB Layout Diagrams
Service Manual Content Service Manual Layout
The form and listing
Name: Title:
Company: Add.: Tel:
E-mail:
Fax:
A. What do you think about the content of this Service Manual?
B. Are you satisfied with this Service Manual?
C. Do you have any other opinions or suggestions regarding this service manual?
63
ViewSonic Corporation Confidential
-
Do Not Copy Q9-1_Q9b-1
Loading...