Viewsonic VP930B-1, VP930-1 Service Manual 1a

Service Manual
ViewSonic VP930/b
Model No. VS10725
19Color TFT LCD Display
ViewSonic
(VP930/b_SM Rev. 1a Oct. 2005)
381 Brea Canyon Road, Walnut, California 91789 USA - (800) 888-8583
Copyright reproduced, transmitted, transcribed, stored in a retrieval system, or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Disclaimer
ViewSonic makes no representations or warranties, either expressed or implied, with respect to the contents hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further, ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents hereof without obligation of ViewSonic to notify any person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation. ViewSonic is a registered trademark of ViewSonic Corporation. All other trademarks used within this document are the property of their respective owners.
2005 by ViewSonic Corporation. All rights reserved. No part of this publication may be
¤
Revision History
ECR Number
1a
10/19/05
Initial Release
Description of Changes
EditorRevision SM Editing Date
G. Han
ViewSonic Corporation Confidential
i
-
Do Not Copy VP930/b
TABLE OF CONTENTS
1. Precautions and Safety Notices
2. Specification
3. Front Panel Function Control Description
4. Circuit Description
5. Adjustment Procedure
6. Troubleshooting Flow Chart
7. Recommended Spare Parts List
8. Exploded Diagram and Exploded Parts List
9. Block Diagram
10. Schematic Diagrams
11. PCB Layout Diagrams
1 5
10
17 18 30
35 43
50 51 57
ViewSonic Corporation Confidential
ii
-
Do Not Copy VP930/b
1. Precautions and Safety Notices
1. Appropriate Operation
(1) Turn off the product before cleaning. (2) Use only a dry soft cloth when cleaning the LCD panel surface. (3) Use a soft cloth soaked with mild detergent to clean the display housing. (4) Use only a high quality, safety approved AC/DC power cord. (5) Disconnect the power plug from the AC outlet if the product will not be used for a long period of time. (6) If smoke, abnormal noise, or strange odor is present, immediately switch the LCD display off. (7) Do not touch the LCD panel surface with sharp or hard objects. (8) Do not place heavy objects on the LCD display, video cable, or power cord. (9) Do not use abrasive cleaners, waxes or solvents for your cleaning. (10) Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas containing excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- In direct sunlight.
2. Caution
No modification of any circuit should be attempted. Service work should only be performed after you are thoroughly familiar
with all of the following safety checks and servicing guidelines.
3. Safety Check
Care should be taken while servicing this LCD display. Because of the high voltage used in the inverter circuit, the voltage is
exposed in such areas as the associated transformer circuits.
4. LCD Module Handling Precautions
4.1 Handling Precautions
(1) Since front polarizer is easily damaged, pay attention not to scratch it. (2) Be sure to turn off power supply when connecting or disconnecting input connector. (3) Wipe off water drops immediately. Long contact with water may cause discoloration or spots. (4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth. (5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface. (6) Since CMOS LSI is used in this module, take care of static electricity and ensure human earth when handling. (7) Do not open or modify the Module Assembly. (8) Do not press the reflector sheet at the back of the module in any direction. (9) In the event that a Module must be put back into the packing container slot after it was taken out of the
container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT Module may be damaged.
(10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate or tilt the Interface
Connector of the TFT Module.
1
D o Not Copy V P930/bViewSonic Corporation Confidential
(11) After installation of the TFT Module into an enclosure (LCD monitor housing, for example), do not twist or
bend the TFT Module even momentarily. When designing the enclosure, it should be taken into consideration that no bending/twisting forces may be applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
(12) The cold cathode fluorescent lamp in the LCD contains a small amount of mercury. Please follow local
ordinances or regulations for disposal.
(13) The LCD module contains a small amount of materials having no flammability grade. The LCD module
should be supplied with power that complies with the requirements of Limited Power Source (IEC60950 or UL1950), or an exemption should be applied for.
(14) The LCD module is designed so that the CCFL in it is supplied by a Limited Current Circuit (IEC60950
or UL1950). Do not connect the CCFL to a Hazardous Voltage Circuit.
2
D o Not Copy V P930/bViewSonic Corporation Confidential
Correct Methods:
Only touch the metal frame of the LCD panel or the front cover of the monitor.Do not touch the surface of the polarizer.
Incorrect Methods: Surface of the LCD panel is pressed by
fingers and that will probably cause “Mura”.
Take out the monitor with cushions
Taking out the monitor by grasping the LCD panel.That will probably cause “Mura”.
D o Not Copy V P930/bViewSonic Corporation Confidential
3
Place the monitor on a clean and soft
foam pad.
Placing the monitor on foreign objects. That will probably scratch the surface of the panel or cause “Mura.”
The panel is placed facedown on
the lap. That will probably cause “Mura.”
4
D o Not Copy V P930/bViewSonic Corporation Confidential
GENERAL specification
Test Resolution & Frequency 1280x1024 @ 60Hz
Test Image Size Full Size
Contrast and Brightness Controls
VIDEO INTERFACE
Input Connector
Default Input Connector Defaults to the first detected input
Video Cable Strain Relief
Video Cable Connector DB-15 Pin
out
Video Signals
Video Impedance 75 Ohms (Analog), 100 Ohms (Digital)
Maximum PC Video Signal 950 mV with no damage to monitor
Maximum Mac Video Signal 1250 mV with no damage to monitor
Sync Signals TTL
DDC/CI Compliant with Revision 1.0
Sync Compatibility
Video Compatibility
Resolution Compatibility
Exclusions Not compatible with interlaced video
Horizontal / Vertical Frequency
2.SPECIFICATIONS
Factory Default: Contrast = 70%, Brightness = 100%
D-SUB1= DB-15(Analog) D-SUB2= DB-15(Analog) DVI= DVI-D(Digital)
Equal to twice the weight of the monitor for five minutes Compliant DDC 2B
Video RGB (Analog) Separate Sync / Composite Sync / SOG TMDS (Digital)
Separate Sync / Composite Sync / SOG Shall be compatible with all PC type
computers, Macintosh computers, and after market video cards 640 x 350, 640 x 400, 640 x 480, 640 x 870, 720 x 400, 720 x 480, 720 x 576, 800 x 600, 832 x 624, 1024 x 768, 1152 x 864, 1152 x 870, 1280 x 720, 1280 x 768, 1280 x 960, 1280 x 1024
Horizontal Frequency 24 – 82 kHz
Vertical Refresh Rate 50 – 85 Hz
Maximum Pixel Clock 135 MHz
Sync Polarity Independent of sync polarity
5
D o Not Copy V P930/bViewSonic Corporation Confidential
Table : 15 pin D-sub connector pin assignment
Pin Number Pin Function
1 Red video input 2 Green video input 3 Blue video input 4 No Connection 5 Ground 6 Red video ground 7 Green video ground 8 Blue video ground
9 +5V 10 Ground 11 No connection 12 (SDA) 13 Horizontal sync (Composite sync) 14 Vertical sync 15 (SCL)
Timing Table
Item
1 640 x 350 @ 70 Hz, 31.5 KHz 2 640 x 400 @ 60 Hz, 31.5 KHz 3 640 x 400 @ 70 Hz, 31.5 KHz 4 640 x 480 @ 50 Hz, 24.7 KHz 5 640 x 480 @ 60 Hz, 31.5 KHz 6 640 x 480 @ 67 Hz, 35.0 KHz 7 640 x 480 @ 72 Hz, 37.9 KHz 8 640 x 480 @ 75 Hz, 37.5 KHz
9 640 x 480 @ 85 Hz, 43.3 KHz 10 640 x 870 @ 75 Hz, 68.9 KHz 11 720 x 400 @ 70 Hz, 31.5 KHz 12 720 x 400 @ 85 Hz, 37.9 KHz 13 720 x 480 @ 60 Hz, 31.5 KHz 14 720 x 576 @ 50 Hz, 31.3 KHz 15 800 x 600 @ 50 Hz, 24.7 KHz 16 800 x 600 @ 56 Hz, 35.1 KHz
Timing Analog Digital Remark
Yes Yes DMT Yes Yes DMT Yes Yes DMT Yes Yes DMT Yes Yes DMT Yes Yes For MAC Yes Yes DMT Yes Yes DMT Yes Yes DMT Yes Yes MAC Yes Yes DMT Yes Yes DMT Yes Yes 480p Yes Yes 576p Yes Yes DMT
Yes Yes DMT
17 800 x 600 @ 60 Hz, 37.9 KHz 18 800 x 600 @ 72 Hz, 48.1 KHz 19 800 x 600 @ 75 Hz, 46.9 KHz 20 800 x 600 @ 85 Hz, 53.7 KHz 21 832 x 624 @ 75 Hz, 49.7 KHz 22 1024 x 768 @ 50 Hz, 39.6 KHz 23 1024 x 768 @ 60 Hz, 48.4 KHz 24 1024 x 768 @ 70 Hz, 56.5 KHz 25 1024 x 768 @ 72 Hz, 58.1 KHz
6
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes MAC
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
D o Not Copy V P930/bViewSonic Corporation Confidential
26 1024 x 768 @ 75 Hz, 60.0 KHz
Yes Yes DMT
27 1024 x 768 @ 75 Hz, 60.2 KHz 28 1024 x 768 @ 85 Hz, 68.7 KHz 29 1152 x 864 @ 75 Hz, 67.5 KHz 30 1152 x 870 @ 75 Hz, 68.7 KHz 31 1280 x 720 @ 50 Hz, 37.5 KHz 32 1280 x 720 @ 60 Hz, 45.0 KHz 33 1280 x 768 @ 50 Hz, 39.6 KHz 34 1280 x 768 @ 60 Hz, 47.4 KHz 35 1280 x 768 @ 60 Hz, 47.8 KHz 36 1280 x 768 @ 75 Hz, 60.3 KHz 37 1280 x 768 @ 85 Hz, 68.6 KHz 38 1280 x 960 @ 50 Hz, 49.4 KHz 39 1280 x 960 @ 60 Hz, 59.7 KHz 40 1280 x 960 @ 75 Hz, 75.2 KHz 41 1280 x 1024 @ 50 Hz, 52.7 KHz 42 1280 x 1024 @ 60 Hz, 64.0 KHz 43 1280 x 1024 @ 75 Hz, 80.0 KHz
Yes Yes For MAC
Yes Yes DMT
Yes Yes DMT
Yes Yes For MAC
Yes Yes 720p
Yes Yes 720p
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
Yes Yes DMT
User Presets
Number of User Presets (recognized timings) Available: 10 presets total in FIFO configuration
7
D o Not Copy V P930/bViewSonic Corporation Confidential
Panel Characteristics
Model number AUO M190EN03 V.0/V.2 Type Active Matrix TFT, PMVA technology Active Size 19” Pixel Arrangement RGB Vertical Stripe Pixel Pitch 0.294 mm Glass Treatment Anti Glare # of Backlights 4 CCFL Backlight Life 50,000 Hours (Typ)
Luminance (Center)– CT =
6500K, Contrast / Brightness = Brightness Uniformity 80%(Typ) / 75%(Min) Contrast Ratio 1000:1 (Typ), 500:1 (Min) Color Depth 16.7 million colors (8 bit panel) Horizontal Viewing Angle 170 degress (Typ) @ CR>10
Vertical Viewing Angle 170degress (Typ) @ CR>10
Response Time 10%-90% @ Ta=25°C
Mercury Panel Defects Please see Panel Quality Specifications.
40,000 Hours (Min) 250 cd/m2 (Typ after 30 minute warm up) 200 cd/m2 (Min after 30 minute warm up)
On/Off Typical= 20 ms (Tr= 13 ms, Tf = 7 ms) GTG
8 ms (Avg)
3.0 mg per lamp
8
D o Not Copy V P930/bViewSonic Corporation Confidential
IMAGE PERFORMANCE
Factory Defaults
Item Defaults Item Defaults Contrast 70% 720x400/640x400 720x400 Brightness 100% Resolution Notice Enabled Color Temperature 6500K Volume N/A Sharpness 100% Balance N/A OSD H. Position 50% Treble N/A OSD V. Position 50% Bass N/A OSD Time Out 15 Sec OSD Background Enabled
Dimension
Width 412 mm (16.2 “) Height (adjust to the top/bottom) 356 mm (14”) / 491mm(19.3” Depth 289 mm (11.4”) Monitor Weight 6.8 kg (15 lbs)
Dimension (Head Only / Wall Mount)
Width 412 mm (16.2”) Height 336 mm (13.2”) Depth 61 mm (2.4”) Monitor Weight 4.2 kg (9.3 lbs)
Ergonomics
Tilt Up 20º Tilt Down From 0º down to -3º ~ -5 º Swivel Right 135º Swivel Left 135º Height Adjust 0 135 mm Pivot 0~90 degress (clockwise)
9
D o Not Copy V P930/bViewSonic Corporation Confidential
3. Front Panel Function Control Description
3.1 Location of Controls
10
D o Not Copy V P930/bViewSonic Corporation Confidential
11
D o Not Copy V P930/bViewSonic Corporation Confidential
12
D o Not Copy V P930/bViewSonic Corporation Confidential
13
D o Not Copy V P930/bViewSonic Corporation Confidential
14
D o Not Copy V P930/bViewSonic Corporation Confidential
15
D o Not Copy V P930/bViewSonic Corporation Confidential
To immediately activate Contrast menu. It should
+ Main
Hot Key for Function Controls
Buttons: Functions:
[1] Main menu [2] Input Select
[Up] or [Dn]
be change to Brightness OSD by push button [2]
[Up] + [Dn] Recall both of Contrast and Brightness to default
[1] + [2] Toggle 720x400 and 640x400 mode when input
720x400 or 640x400 mode.
[1] + [Up] + [Dn] Auto White Balance.(Not shown on user’s guide)
[1] + [Dn] Power Lock [1] + [Up] OSD Lock
[1] + [Dn] + [2] Didable Theft Defence function
[Up] + [PW] + Main
Power On
No signal + [PW] +[2] +
Main Power on
Signal + [PW] +[2]
Power on
Remark : All the short cuts function are only available while OSD off
All reset Burning mode Factory Mode
16
D o Not Copy V P930/bViewSonic Corporation Confidential
4. Circuit Description
1. WORKING THEOREM
A. Scaler
The TSU66AJ is total solution graphics processing IC for LCD monitors with panel resolutions up to SXGA. It is configured with a high-speed integrated triple-ADC/PLL, an integrated DVI receiver, a high quality display processing engine, and an integrated output display interface that can support LVDS panel interface format. To further reduce system costs, the TSU66AJ also integrates intelligent power management control capability for green-mode requirements and spread-spectrum support for EMI management. The TSU66AJ incorporates the world’s first coherent oversampled RGB graphics ADC in a monitor controller system1. The oversampling ADC samples the input RGB signals at a frequency that is much higher than the signal source pixel rate. This can preserve details in the video signal that ordinarily would be lost due to input signal jitter or bandwidth limitations in non-oversampled systems. The TSU66AJ also incorporates a new Dynamic Frame Rate (DFR) generator2 for the digital output video to the display panel that preserves the advantages of a fixed output clock rate, while eliminating the output end of frame short-line.
??
B. MCU:
The MTV416M micro-controller is an 8051 CPU core embedded device targeted for LCD Monitor or LCD TV application. It includes an 8051 CPU core, a 128K-byte internal program Flash-ROM, a 768-byte SRAM, 4 channels of PWM DAC, 4 channels of 6-bit ADC, and a built-in sync-processor. It also includes two IIC Slave B ports, supporting VESA DDC/CI for both D-sub and DVI interfaces, and a Boot-Code-Free ISP (In System Programming).
17
D o Not Copy V P930/bViewSonic Corporation Confidential
Loading...
+ 45 hidden pages