ViewSonic PX725HD User Manual

PX725HD
DLP Projector

User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://

ZZZYLHZVRQLFFRPLQ (QJOLVKRU LQ VSHFL¿FODQJXDJHV XVLQJ WKH 5HJLRQDOVHOHFWLRQ

box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”

Model No. VS16965

Compliance Information

FCC Statement

This device complies with part 15 of FCC Rules. Operation is subject to the follow­ing two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.

This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installa­tion. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interfer­ence will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

y Reorient or relocate the receiving antenna.
y Increase the separation between the equipment and receiver.
y Connect the equipment into an outlet on a circuit different from that to which the

receiver is connected.

y Consult the dealer or an experienced radio/TV technician for help.

Warning:<RXDUHFDXWLRQHGWKDWFKDQJHVRUPRGL¿FDWLRQVQRWH[SUHVVO\DSSURYHG

by the party responsible for compliance could void your authority to operate the
equipment.

For Canada

CAN ICES-3 (B)/NMB-3(B)

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU.

Following information is only for EU-member states:

The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2012/19/EU (WEEE).

The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.

If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,

0.002% Cadmium, or more than 0.004% Lead.

i

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this unit near water.

6. Clean with a soft, dry cloth.

7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves,

RURWKHUGHYLFHVLQFOXGLQJDPSOL¿HUVWKDWSURGXFHKHDW

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
SURQJDUHSURYLGHGIRU\RXUVDIHW\,IWKHSURYLGHGSOXJGRHVQRW¿WLQWR\RXU
outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs.

Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.

 2QO\XVHDWWDFKPHQWVDFFHVVRULHVVSHFL¿HGE\WKHPDQXIDFWXUHU
 8VHRQO\ZLWKWKHFDUWVWDQGWULSRGEUDFNHWRUWDEOHVSHFL¿HGE\

the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.

13. Unplug this unit when unused for long periods of time.

 5HIHUDOOVHUYLFLQJWRTXDOL¿HGVHUYLFHSHUVRQQHO6HUYLFLQJLVUHTXLUHGZKHQWKH

unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.

ii

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
Hexavalent Chromium (Cr
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

6+

) 0.1% < 0.1%

Proposed Maximum
Concentration

Actual Concentration

Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:

Examples of exempted components are:

1. 0HUFXU\LQFROGFDWKRGHÀXRUHVFHQWODPSVDQGH[WHUQDOHOHFWURGHÀXRUHVFHQW

lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.

2. Lead in glass of cathode ray tubes.

3. /HDGLQJODVVRIÀXRUHVFHQWWXEHVQRWH[FHHGLQJE\ZHLJKW

4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

5. Copper alloy containing up to 4% lead by weight.

6. Lead in high melting temperature type solders (i.e. lead-based alloys containing

85% by weight or more lead).

7. Electrical and electronic components containing lead in a glass or ceramic other

than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.

iii

Copyright Information

Copyright © ViewSonic® Corporation, 2017. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks
of Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
WKHULJKWWRFKDQJHSURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFX­ment may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
The ViewSonic CD also provides an opportunity for you to print the product
registration form. Upon completion, please mail or fax to a respective ViewSonic
office. To find your registration form, use the directory “:\CD\Registration”.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
For additional information, please see the “Customer Support” section in this guide.

For Your Records

Product Name: PX725HD

ViewSonic DLP Projector

Model Number: VS16965
Document Number: PX725HD_UG_ENG Rev. 1A 08-24-17
Serial Number: ________________________________________
Purchase Date: ________________________________________

Product disposal at end of product life

The lamp in this product contains mercury which can be dangerous to you and the
environment. Please use care and dispose of in accordance with local, state or
federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

iv

Table of contents

Important safety

instructions.......................2

Introduction......................4

Projector features .................................4

Shipping contents.................................5

Projector exterior view .........................6

Controls and functions.........................7

Positioning your

projector .........................11

Choosing a location............................11

Projection dimensions........................12

Connection......................14

Connecting a computer or a monitor..15

Connecting Video source devices......15

Playing sound through the projector..17

Operation........................18

Starting up the projector.....................18

Using the menus.................................19

Utilizing the password function .........20

Switching input signal........................22

Adjusting the projected image ...........23

Magnifying and searching for

details.................................................24

Selecting the aspect ratio....................24

Optimizing the image.........................26

Setting the presentation timer ............30

Hiding the image................................31

Locking control keys..........................31

Operating in a high altitude

environment .......................................31

Using the CEC function.....................32

Using the 3D functions...................... 32

Using the projector in standby mode. 33

Adjusting the sound........................... 33

Shutting down the projector ..............34

Menu operation .................................. 35

Maintenance...................43

Care of the projector.......................... 43

Lamp information.............................. 44

Troubleshooting.............47

Specifications..................48

Projector specifications...................... 48

Dimensions........................................ 49

Ceiling mount installation ................. 49

Timing chart ................... 50

Copyright information ..54

Appendix.........................55

IR control table..................................55

RS232 command table....................... 56

1

Important safety instructions

Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.

Safety Instructions

1. Please read this manual before you operate your projector. Save it for future

reference.

2. Do not look straight at the projector lens during operation. The intense light beam

may damage your eyes.

3. Refer servicing to qualified service personnel.

4. Always open the lens shutter or remove the lens cap when the projector lamp is

on.

5. In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate

or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).

6. Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or
remote control.

7. The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.

8. Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond the rated life could cause them to break on rare occasions.

9. Never replace the lamp assembly or any electronic components unless the projector is
unplugged.

10. Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.

11. Do not attempt to disassemble this projector . There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable part is the lamp which has its own removable cover.

Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.

12. Do not place this projector in any of the following environments.

- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.

- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.

- Locations where excessive humidity , dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.

- Locations near fire alarms

- Locations with an ambient temperature above 40°C / 104°F

- Locations where the altitudes are higher than 3000 m (10000 feet).

2

13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.

- Do not place this projector on a blanket, bedding or any other soft surface.

- Do not cover this projector with a cloth or any other item.

- Do not place inflammables near the projector.

14. Always place the projector on a level, horizontal surface during operation.

- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the lamp.

15. Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.

16. Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.

17. Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.

18. This product is capable of displaying inverted pictures for ceiling mount installation.

Use only qualified ceiling mount kit for mounting the projector and ensure it is
securely installed.

19. When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.

20. Do not use the Security bar for transporting or installation. It should be used with a
commercially available theft prevention cable.

Safety instructions for ceiling mounting of the projector

We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.

If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely
installed.

If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.

Y ou can p urchase a projector ceiling mount kit from the place yo u purchased your projector.
We recommend that you also purchase a separate security cable and attach it securely to
both the anti-theft lock slot on the projector and the base of the ceiling mount bracket. This
will perform the secondary role of restraining the projector should its attachment to the
mounting bracket become loose.

As with any bright light source, do not stare into the beam, RG2 IEC 62471-5:2015.

3

Introduction

Projector features

The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.

The projector offers the following features.

• Dynamic mode adjusting the power consumption of the lamp according to the
brightness of the image being projected

• Power saving function decreasing the power consumption of the lamp by up to 70%
when no input signal can be detected for a set period of time.

• Presentation timer for better control of time during presentations

• Supports 3D display

•Color Management allowing color adjustments to your liking

• Less than 0.5W power consumption when power saving mode is turned on

• Screen Color correction allowing projection on surfaces of several predefined colors

• Quick auto search speeding up the signal detecting process

• Color modes providing choices for different projection purposes

• Selectable quick power off function

• One-key auto-adjustment to display the best picture quality

• Digital keystone correction to correct distorted images

• Adjustable color management control for data/video display

• Ability to display 1.07 billion colors

• Multi-language On-Screen Display (OSD) menus

• Switchable normal and economic modes to reduce the power consumption

• Component HDTV compatibility (YP

• HDMI CEC (Consumer Electronics Control) function al lo ws sy n c hr on ized power ON/
OFF operation between the projector and a CEC-compatible DVD player device
connected to the HDMI input of the projector

• ISF certified professional image tools with Day/Night modes to optimize color
performance

The apparent brightness of the projected image will vary depending on the ambient lighting
conditions, selected input signal contrast/brightness settings, and is directly proportional to
projection distance.

The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.

bPr)

4

Shipping contents

Carefully unpack and verify that you have all of the items shown below. If any of these
items are missing, please contact your place of purchase.

Standard accessories

The supplied accessories will be suitable for your region, and may differ from those
illustrated.

Projector Power Cord

Quick Start Guide

Optional accessories

1. Replacement lamp

2. VGA-Component adapter

3. Warranty Card (CN only)

4. FCC Compliance Statement (EU only)

Remote Control &

Batteries

5

Projector exterior view

1 2 3 4 5 6 7 8

Front/upper

9

1816 171514 19 20

10 11

12 13

21

Rear/lower side

1. Lamp cover

2. Front IR remote sensor

3. Projection lens

4. Focus ring

5. Zoom ring

6. Power button and LED indicators

7. External control panel
(See "Projector" on page 7 for
details.)

8. Vent (air inlet)

9. AC power cord inlet

10. HDMI-1 port

11. HDMI-2 port

12. RGB (PC) /Component video
(YPbPr/YCbCr) signal input socket

13. RS-232 control port

14. Video input socket

15. Audio signal input L/R socket

16. Audio signal output socket

17. Audio signal input socket

18. USB port (5V/1.5A out)

19. Mini USB port

20. Kensington Security Slot

21. Adjuster foot

Warning

• THIS APPARATUS MUST BE EARTHED.

• When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring,
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should
occur during operation of the unit, operate the disconnect device to switch the power supply
off, or disconnect the power plug.

6

Controls and functions

Projector

21

1. Focus ring

Adjusts the focus of the projected image.

2. Zoom ring

Adjusts the size of the projected image.

3. Power

Toggles the projector between standby
mode and Power ON.

4. (Power indicator light)

Lights up or flashes when the projector is
under operation.

5. (Temperature indicator light)

Lights up red if the projector's temperature
becomes too high.

6. (Lamp indicator light)

Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem.

7. (Menu up)

Selects the desired menu items and makes
adjustments.

(Keystone key)

Manually corrects distorted images
resulting from an angled projection.

8. Blank

Makes the screen blank.

9. Menu

Turns on the On-Screen Display (OSD)
menu.

223 4 5 6 7 8

10 11 12 13 14 159

Exit

Goes back to previous OSD menu, exits
and saves menu settings.

10. Source

Displays the source selection bar.

(Help)

Displays the HELP menu by a long press
for 3 seconds.

11. (Volume down)

Decrease the volume level.

(Left)

Selects the desired menu items and makes
adjustments.

12. (Menu down)

Selects the desired menu items and makes
adjustments.

(Keystone key)

Manually corrects distorted images
resulting from an angled projection.

13. Enter

Enacts the selected On-Screen Display
(OSD) menu item.

14. Color Mode

Selects an available picture setup mode.

15. (Volume up)

Increase the volume level.

(Right)

Selects the desired menu items and makes
adjustments.

7

19

23
24
25

26

27

28

29

20

21

22

18

1
2
3

4

5

6

7
8

9
10
11
12
13
14
15

16
17

Remote control

1. Power

Toggles the projector betwe en standby
mode and Power ON.

2. HDMI 1
Selects HDMI 1 source for display.

3. COMP

Selects D-Sub / Comp. source for
display.

4. Auto Sync

Automatically determines the best
picture timings for the displayed
image.

5. / (Keystone keys)

Manually corrects distorted images
resulting from an angled projection.

Left/ Right/ Up/ Down

Selects the desired menu items and
makes adjustments.

6. (Information)

Displays the Information menu.

7. Menu

Turns on the On-Screen Display
(OSD) menu.

8. Pattern

Displays embedded test pattern.

9. Aspect

Selects the display aspect ratio.

8

10. (Volume down)

Approx. 30°

A

p

pr

o

x

.

3

0°

Decrease the volume level.

11. (Mute)

Toggles th e projector audio between on and
off.

12. Contrast

Displays the contrast setting bar.

13. Brightness

Displays the brightness setting bar.

14. Standard

Displays Standard color mode.

15. 3D

Opens the 3D function OSD.

16. Eco Mode

Selects a lamp mode.

17. Movie

Displays Movie color mode.

18. LED indicator

19. Power Off

Turns the projector off.

20. HDMI 2
Selects HDMI 2 source for display.

Remote control effective range

The Infra-Red (IR) remote control is located on the
front of the projector. The remote control must be held
at an angle within 30 degrees perpendicular to the
projector's IR remote control sensor to function
correctly. The distance between the remote control and
the sensor should not exceed 8 meters (~ 26 feet).

Make sure that there are no obstacles between the
remote control and the IR sensor on the projector that
might obstruct the infra-red beam.

21. Source

Displays the source selection bar.

22. Enter

Enacts the selected On-Screen Display
(OSD) menu item.

23. Exit

Goes back to previous OSD menu, exits
and saves menu settings.

24. Blank

Hides the screen picture.

25. (Help)

Displays the HELP menu.

26. (Volume up)

Increase the volume level.

27. Color Temp

Selects an available picture setup mode.

28. Gaming

Displays Gaming color mode.

29. Sports

Displays Sports color mode.

9

Replacing the remote control batteries

1. To open the battery cover, turn the remote control over to view its back, press on the
finger grip on the cover and pull it up in the direction of the arrow as illustrated.

2. Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.

3. Refit the cover by aligning it with the base and pushing it back down into position.
Stop when it clicks into place.

WARNING

• Avoid leaving the remote control and batteries in an exces sive hea t or humid envi ronment

like the kitchen, bathroom, sauna, sunroom or in a closed car.

• Replace only with the same or equivalent type recommended by the battery manufacturer.

• Dispose of the used batteries according to the manufacturer's instructions and local

environment regulations for your region.

• Never throw the batteries into a fire. There may be danger of an explosion.

• If the batteries are drained or if you will not be using the remote control for an extended

period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.

• RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

• DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.

10

Positioning your projector

Choosing a location

Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.

Your projector is designed to be installed in one of the following 4 possible installation
locations:

1. Front Table

Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.

2. Front Ceiling

Select this location with the projector suspended
upside-down from the ceiling in front of the screen.

Purchase the projector ceiling mount kit from your
dealer to mount your projector on the ceiling.

Set Front Ceiling in the SYSTEM > Projector

Position menu after you turn the projector on.

3. Rear Ceiling

Select this location with the projector suspended
upside-down from the ceiling behind the screen.

Note that a special rear projection screen and the
projector ceiling mounting kit are required for this
installation location.

Set Rear Ceiling in the SYSTEM > Projector

Position menu after you turn the projector on.

4. Rear Table

Select this location with the projector placed near
the floor behind the screen.

Note that a special rear projection screen is
required.

Set Rear Table in the SYSTEM > Projector
Position menu after you turn the projector on.

11

Projection dimensions

(f): Center of lens(e): Screen

• 16:9 image on a 16:9 screen

• 16:9 image on a 4:3 screen

The "screen" mentioned below refers to the projection screen usually consisting of a screen
surface and a support structure.

(a) Screen Size

inch mm inch mm inch mm inch mm inch mm inch mm

50 1270 65 1651 72 1829 25 635 2.2 55 3.7 93
60 1524 78 1981 86 2184 29 737 2.6 66 4.4 112
70 1778 92 2337 101 2565 34 864 3 77 5.2 131
80 2032 105 2667 115 2921 39 991 3.5 88 5.9 149

90 2286 118 2997 129 3277 44 1118 3.9 99 6.6 168
100 2540 131 3327 144 3658 49 1245 4.3 110 7.4 187
110 2794 144 3658 158 4013 54 1372 4.8 121 8.1 205
120 3048 157 3988 173 4394 59 1499 5.2 131 8.8 224
130 3302 170 4318 187 4750 64 1626 5.6 142 9.6 243
140 3556 183 4648 201 5105 69 1753 6 153 10.3 262
150 3810 196 4978 216 5486 74 1880 6.5 164 11 280
170 4318 222 5639 244 6198 83 2108 7.3 186 12.5 318
190 4826 248 6299 273 6934 93 2362 8.2 208 14 355

16:9 image on a 16:9 Screen
(b) Projection distance
min. max. min. max.

(c) Image height

(d) Vertical offs et

12

16:9 image on a 4:3 Screen

(a) Screen Size

inch mm inch mm inch mm inch mm inch mm inch mm

54 1372 65 1651 72 1829 25 635 2.2 55 3.7 93
65 1651 78 1981 86 2184 29 737 2.6 66 4.4 112
76 1930 92 2337 101 2565 34 864 3 77 5.2 131
87 2210 105 2667 115 2921 39 991 3.5 88 5.9 149

98 2489 118 2997 129 3277 44 1118 3.9 99 6.6 168
109 2769 131 3327 144 3658 49 1245 4.3 110 7.4 187
120 3048 144 3658 158 4013 54 1372 4.8 121 8.1 205
131 3327 157 3988 173 4394 59 1499 5.2 131 8.8 224
142 3607 170 4318 187 4750 64 1626 5.6 142 9.6 243
153 3886 183 4648 201 5105 69 1753 6 153 10.3 262
163 4140 196 4978 216 5486 74 1880 6.5 164 11 280
185 4699 222 5639 244 6198 83 2108 7.3 186 12.5 318
207 5258 248 6299 273 6934 93 2362 8.2 208 14 355

There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should physically
test the projection size and distance using the actual projector in situ before y ou perm anently
install it, so as to make allowance for this projector's optica l characteri stics. This will help you
determine the exact mounting position so that it best suits your installa tion location.

(b) Projection distance
min. max. min. max.

(c) Image height

(d) Vertical offs et

13

Connection

6

4

5

8

8

4

3

2

1

2

4

7

Y Pb Pr

Notebook or desktop A/V device

Speakers

When connecting a signal source to the projector, be sure to:

1. Turn all equipment off before making any connections.

2. Use the correct signal cables for each source.

3. Ensure the cables are firmly inserted.

In the connections shown below, some cables may not be included with the projector (see

"Shipping contents" on page 5). They are commercially available from electronics stores.

The connection illustrations below are for reference only. The rear connecting jacks available
on the projector vary with each projector model.

For detailed connection methods, see pages 15-16.

1. VGA cable

2. HDMI cable

3. RS232 cable

4. Audio cable

5. Video cable

6. USB cable

7. Mini USB cable

8. Component Video to VGA (D-Sub)
adapter cable

14

Connecting a computer or a monitor

Connecting a computer

1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.

2. Connect the other end of the VGA cable to the COMPUTER IN signal input socket
on the projector.

Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.

Connecting Video source devices

You can connect your projector to various Video source devices that provide any one of the
following output sockets:

• HDMI

• Component Video

• Video (composite)

You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:

Best video quality

The best available video connection method is HDMI. If your source device is equipped
with an HDMI socket, you can enjoy uncompressed digital video quality.

See "Connecting an HDMI device" on page 16 for how to connect the projector to an HDMI
source device and other details.

If no HDMI source is available, the next best video signal is Component video (not to be
confused with composite video). Digital TV tuner and DVD players output Component
video natively, so if available on your devices, this should be your connection method of
choice in preference to (composite) video.

See "Connecting a Component Video source device" on page 16 for how to connect the
projector to a component video device.

Least video quality

Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.

See "Connecting a composite Video source device" on page 16 for how to connect the
projector to a composite Video device.

Connecting audio

The projector has built-in mono speaker(s) which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. It is not designed
for, nor intended for stereo audio reproduction use as might be expected in home theater or
home cinema applications. Any stereo audio input (if provided), is mixed into a common
mono audio output through the projector speaker.

15

If you wish, you can make use of the projector (mixed mono) speaker in your presentations,

VGA-Component adapter
(ViewSonic P/N: CB-00008906)

and also connect separate amplified speakers to the Audio Out socket of the projector. The
audio output is a stereo signal and controlled by the projector Volume and Mute settings.

If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.

Connecting an HDMI device

You should use an HDMI cable when making connection between the projector and HDMI
devices.

1. Take an HDMI cable and connect one end to the HDMI output port of the video
device.

2. Connect the other end of the cable to the HDMI input port on the projector.

In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI
input and the projected picture displays wrong colors, please change the color space to YUV.
See "Changing HDMI input settings" on page 22 for details.

The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 15 for details.

Connecting a Component Video source device

Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

1. Take a VGA (D-Sub)-Component adaptor cable and connect the end with 3 RCA type
connectors to the Component V ide o output sockets of the Video source device. Match
the color of the plugs to the color of the sockets; green to green, blue to blue, and red
to red.

2. Connect the other end of the VGA (D-Sub)-Component adaptor cable (with a D-Sub
type connector) to the COMPUTER IN socket on the projector.

The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 15 for details.

If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly . Also check that the signal cables have been connected correctly.

Connecting a composite Video source device

Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:

• If so, you can continue with this procedure.

• If not, you will need to reassess which method you can use to connect to the device.

1. Take a Video cable and connect one end to the composite Video output socket of the
Video source device.

2. Connect the other end of the Video cable to the VIDEO socket on the projector.

The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See "Connecting audio" on page 15 for details.

16

If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly . Also check that the signal cables have been connected correctly.

You need only connect to this device using a composite V ideo connection if Component Video
input is unavailable for use. See "Connecting Video source devices" on page 15 for details.

Playing sound through the projector

You can make use of the projector (mixed mono) speaker in your presentations, and also
connect separate amplified speakers to the AUDIO OUT socket of the projector.

If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.

Once connected, the audio can be controlled by the projector On-Screen Display (OSD)
menus. See "Adjusting the sound" on page 33 for details.

17

Operation

Starting up the projector

1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket
switch (where fitted).

2. (If available) Remove the lens cap.

3. Press Power to start the projector . As soon as the lamp lights up, a "Power On Ring
Tone" will be heard. The Power indicator light stays blue when the projector is on.

(If necessary) Rotate the focus ring to adjust the image clearness.

If the projector is still hot from previous activity, it will run the cooling fan for approximately 60
seconds before energizing the lamp.

To maint ain the lamp life, once you turn the projector on, wai t at least 5 minutes before turning
it off.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 33 for details.

4. If the projector is activated for the first time, select your OSD language following the
on-screen instructions.

5. Switch all of the connected equipment on.

6. The projector will start to search for input signals. The current input signal being
scanned appears in the upper left corner of the screen. If the projector doesn't detect a
valid signal, the message 'No Signal' will continue to be displayed until an input
signal is found.
You can also press Source to select your desired input signal. See "Switching input

signal" on page 22 for details.

If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range' displayed on a blank screen. Please cha nge to an i nput signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 50 for details.

18

Using the menus

Current input signal

Main menu icon

Sub-menu

Highlight

Go to the
previous page
or to exit.

Status

The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.

The OSD screenshots below are for reference only, and may differ from the actual design.

Below is the overview of the OSD menu.

To use the OSD menus, please select your language first.

1. Press Menu to turn the OSD menu on.

2. Use / to highlight the SYSTEM

menu.

3. Press to highlight

Language and press //

/ to select a preferred

language.

4. Press Exit twice* to leave and

save the settings.

*The first press leads you back
to the main menu and the
second press closes the OSD
menu.

19

Utilizing the password function

For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on

page 19.

You will be inconvenienced if you enable the password function yet forget the password
somehow. Do make a note of your password, and keep the note in a safe place for later recall.

Setting a password

Once a password has been set and the power on lock i s enabled, the projector ca nnot be used
unless the correct password is entered every time the projector is started.

1. Open the OSD menu and go to the SYSTEM > Security Settings > Change
Password menu.

2. Press Enter and the password dialog box is displayed.

3. Highlight Power On Lock and select On by pressing / .

4. As pictured to the right, the four arrow keys
( , , , ) respectively represent 4 digits (1, 2, 3,

4). According to the password you desire to set, press
the arrow keys to enter six digits for the password.

5. Confirm the new password by re-entering the new
password.

Once the password is set, the OSD menu returns to the
Security Settings page.

6. To leave the OSD menu, press Exit.

If you forget the password

If the password function is activated, you will be
asked to enter the six-digit password every time you
turn on the projector. If you enter the wrong
password, the password error message as pictured
to the right is displayed lasting for 5 seconds, and
the message 'INPUT PASSWORD' follows. You
can retry by entering another six-digit password, or if you did not record the password in
this user manual, and you absolutely do not remember it, you can use the password recall
procedure. See "Entering the password recall procedure" on page 21 for details.

If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.

20

Entering the password recall procedure

1. Press and hold Auto Sync on the remote control for
3 seconds. The projector will display a coded
number on the screen.

2. Write down the number and turn off your projector.

3. Seek help from the local service center to decode
the number. You may be required to provide proof
of purchase documentation to verify that you are an
authorized user of the projector.

The "XXX" shown in the above screenshot are numbers
that vary depending on different projector models.

Changing the password

1. Open the OSD menu and go to the SYSTEM > Security Settings > Change
Password menu.

2. Press Enter. The message 'INPUT CURRENT PASSWORD' is displayed.

3. Enter the old password.

• If the password is correct, another message 'INPUT NEW PASSWORD' is

displayed.

• If the password is incorrect, the password error message is displayed lasting for

5 seconds, and the message 'INPUT CURRENT PASSWORD' is displayed
for your retry. You can press Exit to cancel or try another password.

4. Enter a new password.

5. Confirm the new password by re-entering the new password.

6. You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.

7. To leave the OSD menu, press Exit.

The digits being input will be displayed as asterisks on-screen. Do make a note of your
password, and then keep the note in a safe place for later recall.

Disabling the password function

1. Open the OSD menu and go to the SYSTEM > Security Settings > Power On Lock
menu.

2. Press / to select Off.

3. The message 'INPUT PASSWORD' is displayed. Enter the current password.

• If the password is correct, the OSD menu returns to the Security Settings page

with 'Off' shown in the row of Power On Lock. You will not have to enter the
password next time you turn on the projector.

• If the password is incorrect, the password error message is displayed lasting for

5 seconds, and the message 'INPUT PASSWORD' is displayed for your retry.
You can press Exit to cancel or try another password.

Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.

21

Switching input signal

The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.

Be sure the Quick Auto Search function in the SYSTEM menu is On if you want the
projector to automatically search for the signals.

You can also manually select the desired signal by
pressing one of the source selection keys on the
remote control, or cycle through the available input
signals.

1. Press Source. A source selection bar is
displayed.

2. Press / until your desired signal is
selected and press Enter.
Once detected, the selected source information
will be displayed on the screen for seconds. If there are multiple devices connected to
the projector, repeat steps 1-2 to search for another signal.

Please see "Projector specifications" on page 48 for the native display resolution of this
projector. For best display picture results, you should select and use an input signal which
outputs at this resolution. Any other resolutions will be scaled by the projector depending
upon the 'aspect ratio' setting, which may cause some image distortion or loss of picture
clarity. See "Selecting the aspect ratio" on page 24 for details.

Changing HDMI input settings

In the unlikely event that you connect the projector to a device (like a DVD or Blu-ray
player) via the projector’s HDMI input and the projected picture displays wrong colors,
please change the color space to an appropriate one that fits the color space setting of the
output device.

To do this:

1. Open the OSD menu and go to the ADVANCED > HDMI Settings menu.

2. Press Enter.

3. Highlight HDMI Settings and press / to select a suitable color space according
to the color space setting of the output device connected.

• RGB: Sets the color space as RGB.

• YUV: Sets the color space as YUV.

• Auto: Sets the projector to detect the color space setting of the input signal

automatically.

4. Highlight HDMI Range and press / to select a suitable HDMI color range
according to the color range setting of the output device connected.

• Enhanced: Sets the HDMI color range as 0 - 255.

• Normal: Sets the HDMI color range as 15 - 235.

• Auto: Sets the projector to detect the HDMI range of the input signal

automatically.

This function is only available when the HDMI input port is in use.
Refer to the documentation of the device for information on the color space and HDMI range

settings.

22

Adjusting the projected image

Adjusting the projection angle

The projector is equipped with two adjuster foot. It changes the image height and vertical
projection angle. Screw the adjuster foot to fine tune the angle until the image is positioned
where you want it.

If the projector is not placed on a flat surface or the screen and the projector are not
perpendicular to each other, the projected image becomes trapezoidal. To correct this
situation, see "Correcting keystone" on page 24 for details.

Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.

Auto-adjusting the image

In some cases, you may need to optimize the picture quality . To do this, press Auto Sync on
the remote control. Within 5 seconds, the built -in Intellig ent Auto Adjustment func tion will
re-adjust the values of Frequency and Clock to provide the best picture quality.

The current source information will be displayed in the upper left corner of the screen for 3
seconds.

The screen will be blank while auto adjustment is functioning.
This function is only available when PC D-Sub input signal (analog RGB) is selected.

23

Fine-tuning the image clarity

Press /

Press /

1. Adjust the projected image to the size
that you need using the zoom ring.

2. If necessary, sharpen the image by rotating
the focus ring.

Correcting keystone

Keystoning refers to the situation where the projected image becomes a trapezoid due to
angled projection.

To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.

• Using the remote control

1. Press / to display the Keystone

correction page.

2. Press to correct keystoning at the top of
the image. Press to correct keystoning at
the bottom of the image.

• Using the OSD menu

1. Open the OSD menu and go to the

2. Press Enter. The Keystone correction page is displayed.

3. Press to correct keystoning at the top of the image or press to correct
keystoning at the bottom of the image.

DISPLAY > Keystone menu.

Magnifying and searching for details

If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.

• Using the OSD menu

1. Open the OSD menu and go to the

2. Press Enter. The Zoom bar is displayed.

3. To navigate the picture, press Enter to switch to the paning mode and press the
directional arrows ( , , , ) to navigate the picture.

4. To reduce size of the picture, press Enter to switch back to the zoom in/out
functionality, and press repeatedly until it is restored to the original size. Y ou can
also press Auto Sync on the remote control to restore the picture to its original size.

The picture can only be navigated after it is magnified. You can further magnify the picture
while searching for details.

DISPLAY > Zoom menu.

Selecting the aspect ratio

The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.

24

With the advent of digital signal processing, digital display devices like this projector can

16:10 picture

15:9 picture

4:3 picture

16:9 picture

4:3 picture

2.35:1 picture

dynamically stretch and scale the image output to a different aspect than that of the image
input signal.

To change the projected image ratio (no matter what aspect the source is):

1. Open the OSD menu and go to the

DISPLAY > Aspect Ratio menu.

2. Press / to select an aspect ratio to suit the format of the video signal and your
display requirements.

About the aspect ratio

In the pictures below, the black portions are inactive areas and the white portions are acti ve
areas. OSD menus can be displayed on those unused black areas.

1. Auto: Scales an image proportionally to fit the
projector's native resolution in its horizontal
width. This is suitable for the incoming image
which is neither in 4:3 nor 16:9 and you want to
make most use of the screen without altering the
image's aspect ratio.

2. 4:3: Scales an image so that it is displayed in the
center of the screen with a 4:3 aspect ratio. This
is most suitable for 4:3 images like computer
monitors, standard definition TV and 4:3 aspect
DVD movies, as it displays them without aspect
alteration.

3. 16:9: Scales an image so that it is displayed in
the center of the screen with a 16:9 aspect ratio.
This is most suitable for images which are
already in a 16:9 aspect, like high definition TV,
as it displays them without aspect alteration.

4. Panorama: Scales a 4:3 image vertically and
horizontally in a non-linear manner so that it
fills the screen.

5. 2.35:1: Scales an image so that it is displayed in
the center of the screen with a 2.35:1 aspect
ratio without aspect alteration.

25

6. Anamorphic: Scales a 2.35:1 aspect image so

2.35:1 picture

that it fills the screen.

Optimizing the image

Selecting a picture mode

The projector is preset with several predefined picture modes so that you can choose one to
suit your operating environment and input signal picture type.

To select an operation mode that suits you r need, you can follow one of the following steps.

• Press Standard, Gaming, Movie and Sports on the remote control until your desired

mode is selected.

•Go to the IMAGE > Color Mode menu and press / to select a desired mode.

Picture modes for different types of signals

The picture modes available for different types of signals are listed below.

1. Brightest mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.

2. Sport: Optimized for viewing sport match in well-lit environments.

3. Standard mode: Is designed for presentations under daylight environment to match
PC and notebook coloring.

4. Gaming: Suitable for playing video games in a bright living room.

5. Movie mode (Rec.709): Is appropriate for playing colorful movies, video clips from
digital cameras or DVs through the PC input for best viewing in a blackened (little
light) environment.

6. ISF Day/ISF Night mode: Only available when ISF Mode is On.

Selectable lamp modes may vary depending on the Color Mode selected.

Using Screen Color

In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Screen Color feature can help correct the projected picture’s colors to
prevent possible color difference between the source and projected pictures.

To use th is function, go to the DISPLAY > Screen Color menu and press / to select a
color which is closest to the color of the projection surface. There are several precalibrated
colors to choose from: Whiteboard, Greenboard, and Blackboard. The effects of these
settings may vary depending on different models.

This function is only available when a PC or HDMI input signal is selected.

Fine-tuning the image quality in user modes

According to the detected signal type, there are some user-definable functions available.
You can make adjustments to these functions based on your needs.

26

Adjusting Brightness

50

-30

+80

Go to the IMAGE > Brightness menu and press /.
The higher the value, the brighter the image. And the

lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.

Adjusting Contrast

Go to the IMAGE > Contrast menu and press / .
The higher the value, the greater the contrast. Use this

to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.

-30

0

Adjusting Color

Go to the IMAGE > ADVANCED > Color menu and press / .
Lower setting produces less saturated colors. If the setting is too high, colors on the image

will be overpowering, which makes the image unrealistic.

This function is only available when the input signal is Video, YPbPr (digital) or YCbCr
(digital).

Adjusting Tint

Go to the IMAGE > ADVANCED > Tint menu and press / .
The higher the value, the more reddish the picture becomes. The lower the value, the more

greenish the picture becomes.

This function is only available when the input signal is Video, YPbPr (digital) or YCbCr
(digital).

Adjusting Sharpness

Go to the IMAGE > ADVANCED > Sharpness menu and press / .
The higher the value, the sharper the picture becomes. The lower the value, the softer the

picture becomes.

This function is only available when the input signal is Video, YPbPr (digital) or YCbCr
(digital).

Adjusting Brilliantcolor

Go to the IMAGE > ADVANCED > Brilliantcolor menu and press / .
This feature utilizes a new color-processing algorithm and system level enhancements to

enable higher brightness while providing truer, more vibrant colors in the projected picture.
It enables a greater than 50% brightness increase in mid-tone images, which are common in
video and natural scenes, so the projector reproduces images in realistic and true colors. If
you prefer images with that quality, select a level that suits your need. If you don’t need it,
select Off.

Reducing image noise

Go to the IMAGE > ADVANCED > Noise Reduction menu and press / .
This function reduces electrical image noise caused by different media players. The higher

the setting, the less the noise.

This function is only available when a PC, or Video input signal is selected.

+40

27

Selecting a gamma setting

Go to the IMAGE > ADVANCED > Gamma menu and select a preferred setting by
pressing / .

Gamma refers to the relationship between input source and picture brightness.

Selecting a Color Temperature

Go to the IMAGE > Color Temp menu and press / .
The options available for color temperature settings vary according to the signal type

selected.

1. Cool: With the highest color temperature, Cool makes the image appear the most
bluish white than other settings.

2. Normal: Maintains normal colorings for white.

3. Warm: Makes images appear reddish white.

Setting a preferred color temperature

1. Go to the IMAGE > Color Temp menu.

2. Press / to select Cool, Normal or Warm and press Enter.

3. Press / to highlight the item you want to change and adjust the values by
pressing /

• Red Gain/Green Gain/Blue Gain: Adjusts the contrast levels of Red, Green,

and Blue.

• Red Offset/Green Offset/Blue Offset: Adjusts the brightness levels of Red,

Green, and Blue.

This function is only available when a PC input signal is selected.

.

Color Management

Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction, should
you require it.

If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc., you can project any image
from the disc on the screen and enter the Color Management menu to make adjustments.

To adjust the settings:

1. Open the OSD menu and go to the IMAGE > ADVANCED > Color Management
menu.

2. Press Enter and the Color Management page is displayed.

3. Highlight Primary Color and press / to select a color from among Red, Ye llow,
Green, Cyan, Blue, or Magenta.

4. Press to highlight Hue and press / to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.

28

Please refer to the illustration to the right for

RED

BLUE

GREEN

Yellow

Cyan

Magenta

how the colors relate to each other.
For example, if you select Red and set its

range at 0, only pure red in the projected
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.

5. Press to highlight Saturation and adjust
its values to your preference by pressing /

. Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will
be affected.

Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.

6. Press to highlight Gain and adjust its values to your preference by pressing / .

The contrast level of the primary color you select will be affected. Every adjustment
made will reflect to the image immediately.

7. Repeat steps 3 to 6 for other color adjustments.

8. Make sure you have made all of the desired adjustments.

9. Press Exit to exit and save the settings.

29

Setting the presentation timer

Presentation timer can indicate the presentation time on the screen to help you achieve
better time management when giving presentations. Follow these steps to utilize this
function:

1. Go to the BASIC > Presentation Timer menu.

2. Press Enter to display the Presentation Timer page.

3. Highlight Timer Period and decide the time period by pressing / . The length of

time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5­minute increments.

If the timer is already on, the timer will restart whenever the Timer Period is reset.

4. Press to highlight Timer Display and choose if you want the timer to show up on

the screen by pressing

Selection Description

Always
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).

Never Hides the timer throughout the presentation time.

5. Press to highlight Timer Position and set the timer position by pressing / .

Top-Left Bottom-Left Top-Right Bottom-Right

6. Press to highlight Timer Counting Direction and select your desired counting
direction by pressing / .

Selection Description
Count Up Increases from 0 to the preset time.
Count Down Decreases from the preset time to 0.

/ .

Displays the timer on screen throughout the presentation
time.

7. Press to highlight Sound Reminder and decide if you want to activate sound
reminder by pressing / . If you select On, a double beep sound will be heard at

the last 30 seconds of counting down/up, and a triple beep sound will be produced
when the timer is up.

8. To activate the presentation timer, press and press / to highlight Start
Counting and press Enter.

9. A confirmation message displays. Highlight Yes and press Enter to confirm. You will
see the message “Timer is On” displaying on the screen. The timer starts counting
when the timer is on.

To cancel the timer, perform the following steps:

1. Go to the BASIC > Presentation Timer menu.

2. Highlight Off. Press Enter. A confirmation message displays.

3. Highlight Yes and press Enter to confirm. You will see the message “Timer is Off”
displaying on the screen.

30

Hiding the image

In order to draw the audience's full attention to the presenter, you can press BLANK to hide
the screen image. Press any key on the projector or remote control to restore the image. The
word 'BLANK' appears at the lower right corner of the screen while the image is hidden.

You can set the blank time in the BASIC
the image automatically after a period of time when there is no action taken on the blank
screen.

Once Blank is pressed, the projector enters Eco mode automatically.
CAUTION

Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.

> Blank Timer menu to let the projector return

Locking control keys

With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no

control keys on the projector will operate except Power.

1. Go to the

2. Press / to select On.

3. A confirmation message is displayed. Select Yes to confirm.

You can also use the remote control to enter the
press / to select Off.

Keys on the remote control are still functional when panel key lock is enabled.

If you press Power to turn off the projector without disabling panel key lock, the projector
will still be in locked status the next time it is turned on.

SYSTEM > Panel Key Lock menu.

SYSTEM > Panel Key Lock menu and

Operating in a high altitude environment

We recommend you use the High Altitude Mode when your environment is between 1500
m–3000 m above sea level, and temperature is between 5°C–25°C.

CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperat ure

is between 5°C and 35°C. The projector will be over cooled, if you turn the mode on under
such a condition.

To activate the High Altitude Mode:

1. Open the OSD menu and go to the SYSTEM > High
Altitude Mode menu.

2. Press / to select On. A confirmation message is
displayed.

3. Highlight Yes and press Enter.

Operation under "High Altitude Mode" may cause a higher
decibel operating noise level because of increased fan speed
necessary to improve overall system cooling and performance.

If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude Mode to solve these symptoms.

31

However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.

Using the CEC function

This projector supports CEC (Consumer Electronics Control) function for synchronized
power on/off operation via HDMI connection. That is, if a device that also supports CEC
function is connected to the HDMI input of the projector, when the projector’s power is
turned off, the power of the connected device will also be turned off automatically. When
the power of the connected device is turned on, the projector’s power will be turned on
automatically.

To turn on the CEC function:

1. Open the OSD menu and go to the POWER MANAGEMENT > Auto Power On >
CEC menu.

2. Press / to select All.

In order for the CEC function to work properly, make sure that the device is correctly
connected to the HDMI input of the projector via an HDMI cable, and its CEC function is turned
on.

Depending on the connected device, the CEC function may not work.

Using the 3D functions

This projector features 3D function which enables you to enjoy 3D movies, videos, and
sporting events in a more realistic way by presenting the depth of the images. You need to
wear a pair of 3D glasses to view 3D images.

If the 3D signal is input from an HDMI 1.4a compatible device, the projector detects the
signal for 3D Sync information and once detected, it projects images in 3D format
automatically. In other cases, you may need to manually select a 3D Sync format for the
projector to project 3D images correctly.

To select a 3D Sync format:

1. Press 3D on the remote control to access the 3D Settings menu or go to the
ADVANCED > 3D Settings menu.

2. Press Enter. The 3D Settings page is displayed.

3. Highlight 3D Sync and press Enter.

4. Press

When the 3D Sync function is on:

• The brightness level of the projected image will decrease.

• The Color Mode cannot be adjusted.

• The Zoom function can only magnify the pictures to limited sizes.

If you discover the inversion of the 3D image depth, set the 3D Sy nc Inver t function to “Inver t”
to correct the problem.

to select a 3D Sync setting and then press Enter to confirm.

32

Using the projector in standby mode

Some of the projector functions are available in standby mode (plugged in but not turned
on). To use these functions, be sure you have turned on the corresponding menus under
POWER MANAGEMENT > Standby Settings, and the cable connections are correctly
made. For the connection methods, see the Connection chapter.

Active Audio Out

Selecting On outputs an audio signal when the AUDIO IN socket is correctly connected to
a proper device.

Adjusting the sound

The sound adjustments made as below will have an effect on the projector speaker. Be sure
you have made a correct connection to the projector audio input/output jacks. See

"Connection" on page 14 for more details.

Muting the sound

1. Open the OSD menu and go to the BASIC > Audio Settings > Mute menu.

2. Press / to select On.

If available, you can press on the remote control to toggle the projector audio between on
and off.

Adjusting the sound level

1. Open the OSD menu and go to the BASIC > Audio Settings > Audio Volume menu.

2. Press / to select a desired sound level.

If available, you can press or on the remote control to adjust the projector’s sound
level.

Turning off the Power On/Off Ring Tone

1. Open the OSD menu and go to the BASIC > Audio Settings > Power On/Off Ring
Tone menu.

2. Press / to select Off.

The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound
mute or changing the sound level will not affect the Power On/Off Ring Tone.

33

Shutting down the projector

1. Press Power and a confirmation message is displayed prompting you.
If you don't respond in a few seconds, the message will disappear .

2. Press Power a second time.

3. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect
the power cord from the wall socket if the projector will not be used in an extended
period of time.

To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 33 for details.
CAUTION

• To protect the lamp, the projector will not respond to any commands during the cooling

process.

• To shorten the cooling time, you can also activat e the Quick Power Off function. See

"Quick Power Off" on page 40 for details.

• Do not unplug the power cord before the projector shutdown sequence is complete.

34

Menu operation

Menu system

Please note that the on-screen display (OSD) menus vary according to the signal type
selected.

The menu items are available when the projector detects at least one valid signal. If there is
no equipment connected to the projector or no signal detected, limited menu items are
accessible.

Main menu Sub-menu Options

Screen Color Off/Blackboard/Greenboard/Whiteboard

Auto/4:3/16:9/Panorama/2.35:1/
Anamorphic

Brightest/Sports/Standard/Gaming/
Movie(Rec.709)/ISF Day/ISF Night

Warm/Normal/Cool
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
Blue Offset

Primary Color
Hue
Saturation
Gain

1.

DISPLAY

2.

IMAGE

Aspect Ratio
Keystone

Position
Phase
H. Size
Zoom
OverScan Off/1/2/3/4/5
3X Fast Input Inactive/Active

Color Mode
Brightness

Contrast

Color Temp

Color
Tint
Sharpness
Gamma C1~C8/G1~G5/DICOM SIM/sRGB

ADVANCED

Reset Color Settings Reset/Cancel
ISF Mode (input password)

Brilliantcolor Off/1/2/3/4/5/6/7/8/9/10
Noise Reduction

Color
Management

35

Main menu Sub-menu Options

Signal Disable/VGA/HDMI/All

3. POWER
MANAGEME
NT

4. BASIC

Auto Power On

Smart Energy

Standby
Settings

Smart Restart Disable/Enable
Quick Power Off Disable/Enable

Audio Settings

Presentation
Timer

Pattern Off/Grid
Blank Timer
Message On/Off

Splash Screen Black/Blue/ViewSonic

CEC Disable/Enable
Direct Power On Off/On
Auto Power Off Disable/10 min/20 min/30 min

Sleep Timer
Power Saving Enable/Disable
Active Audio Out Off/On

Mute On/Off
Audio Volume 0 ~ 20
Power On/Off Ring

Tone
Timer Period

Timer Display

Timer Position
Timer Counting

Direction
Sound Reminder On/Off
Start Counting/Off Yes/No

Disable/30 min/1 hr /2 hr/3 hr/
4 hr/8 hr/12 hr

On/Off
1 ~ 240

(1,2,3,4,5,10,15,20,60,…240)
Always/1 min /2 min/3 min/

Never
Top-Lef t/Bottom-Left/Top-

Right/Bottom-Right
Count Down/Count Up

Disable/5 min/10 min/15 min/
20 min/25 min/30 min

36

Main menu Sub-menu Options

Auto/Off/Frame

5. ADVANCED

6.
SYSTEM

7.
INFORMATION

3D Settings

HDMI Settings

Lamp Settings

DCR Off/On
Closed Caption Off/CC1/CC2/CC3/CC4
Reset Settings Reset/Cancel

Language
Projector

Position

Menu Settings

High Altitude
Mode

Quick Auto
Search

Security
Settings

Panel Key Lock Off/On

Baud Rate

Current System Status

3D Sync

3D Sync Invert Disable/Invert
HDMI Format Auto/RGB/YUV
HDMI Range Auto/Enhanced/Normal

Lamp Mode
Reset Lamp Hours Rese t/Cancel

Lamp Hours

Menu Display Time

Menu Position

Change Password
Power on Lock Off/On

Sequential/Frame Packing/
Top-Bottom/Side-by-Side

Normal/Eco/Dynamic/
SuperEco

Multi-language OSD
selection

Front Table/Rear Table/
Rear Ceiling/Front Ceiling

5 sec/10 sec/15 sec/20 sec/
25 sec/30 sec

Center/Top-Left/Top-Right/
Bottom-Left/Bottom-Right

Off/On

Off/On

2400/ 4800/ 9600/ 14400/
19200/ 38400/ 57600/
115200

• Source

• Color Mode

• Resolution

• Color System

• Firmware Version

• 3X Fast Input

• S/N

37

Description of each menu

1. DISPLAY menu

Function Description

See "Using Screen Color" on page 26 for details.

Screen Color

Aspect Ratio See "Selecting the aspect ratio" on page 24 for details.
Keystone See "Correcting keystone" on page 24 for details.

Position

Phase

H. Size

Zoom

OverScan

3X Fast Input

This function is only available when a PC input signal is
selected.

Displays the position adjustment page. To move the projected
image, use the directional arrow keys. The values shown on the
lower position of the page change with every key press you made
until they reach their maximum or minimum.

This function is only available when a PC input signal is
selected.

The adjustment range may vary under different timings.

Adjusts the clock phase to reduce image
distortion.

This function is only available when
a PC input signal is selected.

Adjusts the horizontal width of the image.

This function is only available when a PC input signal is
selected.

See "Magnifying and searching for details" on page 24 for
details.

Adjusts the overscan rate from 0% to 3%.

This function is only available when a Composite Video or
HDMI input signal is selected.

Selecting Active enables the function. This function is favorable
to frame rate reducing. Quick response time in native timing can
be achieved. When enabled, the following settings will return to
factory preset values: Aspect Ratio, Keystone, Position, Zoom,
OverScan.

This function is only available when a 1080p input signal
is selected.

38

Function Description

2. IMAGE menu

Color Mode See "Selecting a picture mode" on page 26 for details.
Brightness See "Adjusting Brightness" on page 27 for details.
Contrast See "Adjusting Contrast" on page 27 for details.

Color Temp

See "Selecting a Color Temperature" on page 28 and "Setting a

preferred color temperature" on page 28 for details.

Color

See "Adjusting Color" on page 27 for details.

Tint

See "Adjusting Tint" on page 27 for details.

The function is only available when Video input with NTSC
system is selected.

Sharpness

See "Adjusting Sharpness" on page 27 for details.

ADVANCED

Gamma

See "Selecting a gamma setting" on page 28 for details.

Brilliantcolor

See "Adjusting Brilliantcolor" on page 27 for details.

Noise Reduction

See "Reducing image noise" on page 27 for details.

Color Management

See "Color Management" on page 28 for details.

Reset Color
Settings

Returns all color settings to the factory preset values.

The ISF calibration menu is password protected and only
accessible by authorized ISF calibrators. The ISF (Imaging
Science Foundation) has developed carefully crafted, industry­recognized standards for optimal video performance and has
implemented a training program for technicians and installers to
use these standards to obtain optimal picture quality from ISF

ISF Mode

certified display devices. Accordingly , we reco mmend that setu p
and calibration be performed by an ISF certified installation
technician.

The default password is: , , , , , .
For more information, go to www.imagingscience.com or

contact the dealer or reta iler from whom you pur chased the
projector.

39

Function Description

3. POWER MANAGEMENT menu

4. BASIC menu

Signal

Selecting All allows the projector to turn on automatically once
the VGA/HDMI signal is fed through the VGA/HDMI cable.

Auto Power On

CEC

See "Using the CEC function" on page 32 for details.

Direct Power On

Selecting On allows the projector to turn on automatically
once the power is fed through the power cord.

Auto Power Off

See "Setting Auto Power Off" on page 44 for details.

Smart Energy

Sleep Timer

See "Setting Sleep Timer" on page 44 for details.

Power Saving

See "Setting Power Saving" on page 44 for details.

Standby
Settings

See "Using the projector in standby mode" on page 33 for
details.

Selecting Enable you to restart the projector immediately
within 120 seconds after turning it off. After 120 seconds, if
the projector is not turned on again, it will directly enter the
standby mode.

Smart Restart

It takes some time to initiate this function. Make sure the
projector has been turned on for more than 4 minutes. If
the projector is resumed by using the Smart Restart
feature, this function can be executed immediately.

When All is selected, the Quick Power Off function will be
automatically set to “All”.

Selecting Enable enables the function and the projector will
not enter the cooling process after being shut down. Selecting
Disable disables the function and the projector will enter

Quick Power
Off

normal cooling process after being shut down.

If you attempt to restart the projector right after it’ s been
turned off, it may not be turned on successfully and will
rerun its cooling procedure.

When Disable is selected, the Smart Restart function will
be automatically turned off.

Audio Settings See "Adjusting the sound" on page 33 for details.

40

Function Description

4. BASIC menu

5. ADVANCED menu

Presentation
Timer

See "Setting the presentation timer" on page 30 for details.

The projector can display grid test patterns. It helps you adjust

Pattern

the image size and focus and check that the projected image is
free from distortion.

Blank Timer See "Hiding the image" on page 31 for details.
Message

Splash Screen

Selecting On displays the current information on the screen
when the projector is detecting or searching for a signal.

Allows you to select which logo screen will be displayed
during projector start-up.

3D Settings See "Using the 3D functions" on page 32 for details.
HDMI Settings See "Changing HDMI input settings" on page 22 for details.

Lamp Mode

See "Setting Lamp Mode as Eco" on page 44 for details.

Reset Lamp Hours

Lamp Settings

Resets the lamp timer after new lamp is installed. For changing
the lamp, please contact qualified service personnel.

Lamp Hours

See "Getting to know the lamp hour" on page 44 for details on
how the total lamp hour is calculated.

Enables or disables the DCR (Dynamic Contrast Ratio)
function. Selecting On enables the function and the projector
will automatically switch the lamp mode between normal and
economic modes according to the input image detected.

DCR

This function is only available when a PC input signal is
selected.

After enabling DCR, frequent lamp mode switching may
shorten lamp life and noise level will vary during
operation.

Caption Version

Closed Caption

Selects a preferred closed captioning mode. To view captions,
select CC1, CC2, CC3, or CC4 (CC1 displays captions in the
primary language in your area).

Returns all settings to the factory preset values.

Reset Settings

The following settings will still remain: Keystone,
OverScan, Language, Projector Position, High Altitude
Mode, Security Settings, 3D Settings, ISF Mode.

41

Function Description

6. SYSTEM menu

7. INFORMATION menu

Language
Projector

Position

Menu Settings

High Altitude
Mode

Quick Auto
Search

Security
Settings

Panel Key Lock See "Locking control keys" on page 31 for details.
Baud Rate Selects RS-232 baud rate.

Current System
Status

Sets the language for the On-Screen Display (OSD) menus.
See "Using the menus" on page 19 for details.

See "Choosing a location" on page 11 for details.

Menu Display Time

Sets the length of time the OSD will remain active after your
last key press. The range is from 5 to 30 seconds in 5-second
increments.

Menu Position

Sets the On-Screen Display (OSD) menu position.

A mode for operation in high altitude areas.

See "Switching input signal" on page 22 for details.

See "Utilizing the password function" on page 20 for details.

Source

Shows the current signal source.

Color Mode
Shows the selected mode in the IMAGE menu.

Resolution

Shows the native resolution of the input signal.

Color System

Shows input system format.

Firmware Version

Shows the current firmware version.

3X Fast Input

Shows whether the function is activated or not.

S/N

Shows the project serial number.

42

Maintenance

Care of the projector

You need to keep the lens and/or filter (optional accessory) clean on a regular basis.
Never remove any parts of the projector. Contact your dealer when any part of the projector

needs replacing.

Cleaning the lens

Clean the lens whenever you notice dirt or dust on the surface.

• Use a canister of compressed air to remove dust.

• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.

CAUTION
Never rub the lens with abrasive materials.

Cleaning the projector case

Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 34 and unplug the power cord.

• To remove dirt or dust, wipe the case with a soft, lint-free cloth.

• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.

CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.

Storing the projector

If you need to store the projector for an extended time, please follow the instructions below:

• Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to "Specificatio ns" on p ag e 48 or
consult your dealer about the range.

• Retract the adjuster foot.

• Remove the battery from the remote control.

• Pack the projector in its original packing or equivalent.

Transporting the projector

It is recommended that you ship the projector with its original packing or equivalent.

43

Lamp information

Getting to know the lamp hour

When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer.

To obtain the lamp hour information:

1. Open the OSD menu and go to the ADVANCED > Lamp Settings menu.

2. Press Enter and the Lamp Settings page is displayed.

3. You will see the Lamp Hours information on the menu.

4. To leave the menu, press Exit.

Extending lamp life

The projection lamp is a consumable item. To keep the lamp life as long as possible, you
can do the following settings via the OSD menu.

Setting Lamp Mode as Eco

Using Eco mode reduces system noise and power consumption by 20%. If the Eco mode is
selected, the light output will be reduced and result in darker projected pictures.

Setting the projector in Eco mode also extends the lamp operation life. T o set Eco mode, go
to the ADVANCED > Lamp Settings > Lamp Mode menu and press / to select Eco.

Setting Auto Power Off

This function allows the projector to turn off automatically after a set period of time once no
input source is detected to prevent unnecessary waste of lamp life.

1. Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy

menu.

2. Press Enter and the Smart Energy page is displayed.

3. Highlight Auto Power Off and press / .

4. If the preset time lengths are not suitable for your need, select Disable. The projector

will not automatically shut down in a certain time period.

Setting Sleep Timer

This function allows the projector to turn off automatically after a set period of time to
prevent unnecessary waste of lamp life.

1. Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy

menu.

2. Press Enter and the Smart Energy page is displayed.

3. Highlight Sleep Timer and press / .

4. If the preset time lengths are not suitable for your need, select Disable. The projector

will not automatically shut down in a certain time period.

Setting Power Saving

The projector lowers the power consumption if no input source is detected after 5 minutes to
prevent unnecessary waste of lamp life. You can further decide if you would like the
projector to turn off automatically after a set period of time.

1. Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy

menu.

44

2. Press Enter and the Smart Energy page is displayed.

3. Highlight Power Saving and press / .

4. When Enable is selected, the projector lamp will be changed to Eco mode after no

signal is detected for 5 minutes.
The lamp power will be changed to SuperEco mode after no signal is detected for 20
minutes.

Timing of replacing the lamp

Please install a new lamp or consult your dealer when the Lamp indicator light lights up. An
old lamp may cause a malfunction in the projector and in some instances the lamp may
explode.

CAUTION
The Lamp indicator light and Temperature indicator light will light up if the lamp becomes too

hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp indicator light or
Temperature indica tor light still lights up after turning the power back on, please contact your
dealer. See "Indicators" on page 46 for details.

Replacing the lamp

Turn the power off and disconnect the projector from the power outlet. Please contact
qualified service personnel for changing the lamp.

45

Indicators

Light

Blue

ON Off Off
Flashing Off Off
Flashing Off Off

2 blinks Off Off
7 blinks Off Off
8 blinks Off Off
9 blinks Off Off

5 blinks Off Off
5 blinks Off 1 blinks

5 blinks Off 2 blinks

5 blinks Off 3 blinks
5 blinks Off 4 blinks
5 blinks Off 5 blinks
5 blinks Off 6 blinks
5 blinks Off 7 blinks
5 blinks Off 8 blinks
5 blinks Off 10 blinks
5 blinks Off 11 blinks
5 blinks Off 12 blinks
5 blinks Off 13 blinks
5 blinks Off 14 blinks
5 blinks Off 15 blinks

Off On Off

4 blinks Off Off
4 blinks Off 4 blinks
6 blinks Off 1 blinks
6 blinks Off 2 blinks
6 blinks Off 3 blinks

Red

Status & Description

Red

Power events

Lamp Ready
Start
Cooling
Scaler Stops Working
Case Open
DMD Error
Color Wheel Error

Lamp events

Lamp Re-Strike 6 Times Failed
Lamp Temperature Shut Down (Ballast Temp.)
Lamp Short Circuit in Output Detected (Ballast

Circuit Short)
Lamp End of Lamp Life Detected
Lamp Did Not Ignite
Lamp Extinguished During Normal Operation
Lamp Extinguished During Run-Up Phase
Lamp Voltage Too Low
Lamp Ballast Fail
Lamp Ballast COMM. fail
Lamp Ballast Over Temp.
Restrike Lamp Fail 1
Restrike Lamp Fail 2
Lamp Fail 1
Lamp Fail 2

Thermal events

Over Temperature
Thermal Break Sensor Error
G794 Error(Fan IC I2C Connection Error)
Fan 1 Error
Fan 2 Error
Fan 3 Error

46

Troubleshooting

The projector does not turn on.

Cause Remedy

There is no power from the power cord.

Attempting to turn the projector on again
during the cooling process.

No picture

Cause Remedy

The video source is not turned on or
connected correctly.

The projector is not correctly connected to
the input signal device.

The input signal has not been correctly
selected.

Blurred image

Cause Remedy

The projection lens is not correctly focused. Adjust the focus of the lens using the focus ring.
The projector and the screen are not

aligned properly .

Remote control does not work

Cause Remedy

The battery is out of power. Replace the battery with a new one.
There is an obstacle between the remote

control and the projector.
You are too far away from the projector. Stand within 8 meters (26 feet) from the projector.
The remote control code on the projector

and that on the remote control are not
consistent.

Plug the power cord into the AC inlet on the
projector, and plug the power cord int o the power
outlet. If the power outlet has a switch, make sure
that it is switched on.

Wait until the cooling down process has completed.

Turn the video source on and check that the si gnal
cable is connected correctly.

Check the connection.
Select the correct input signal with the Source key

on the projector or remote control.

Adjust the projection angle and direction as well as
the height of the projector if necessary.

Remove the obstacle.

Adjust the remote control code.

47

Specifications

Projector specifications

• All specifications are subject to change without notice.

• Not all models can be purchased in your region.

General

Product name DLP Projector

Optical

Resolution 1920 x 1080 1080p
Display system 1-CHIP DMD
Lamp 240 W lamp

Electrical

Power supply AC100–240V , 50–60 Hz (Automatic)
Power consumption 330 W (Max); < 0.5 W (Standby)

Mechanical

Weight 2.94 Kg (6.48 lbs)

Input terminal

Computer input
RGB input D-Sub 15-pin (female) x 1
Video signal input
VIDEO RCA jack x 1
SD/HDTV signal input

Analog – D-Sub <–> Component RCA jack x 3 (through RGB input)

Digital – HDMI V1.4a x 1

Audio signal input Audio in jack x 1
HDMI input x 2

Output terminal

Audio signal output Audio jack x 1
Speaker 8 watt x 1
USB Type A DC5V/1.5A

Control terminal

RS-232 serial control 9 pin x 1
USB serial control Type mini B
IR receiver x 1 (Front)

Environmental Requirements

Operating temperature 5°C–40°C at sea level
Operating relative humidity
Operating altitude • 0–1499 m at 5°C–35°C

Storage temperature -10°C to +60°C
Storage humidity 10% to 85% Non-Condensing
Storage altitude 30°C@ 0 to 12200m above sea level

Audio in jack L/R in x 1

10%–90% (without condensation)

• 1500–3000 m at 5°C–25°C (with

High Altitude Mode

on)

48

Dimensions

233.29mm (9.2")

347.66mm (13.6" )

65mm (2.56")

106.9mm (4.2")

Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)

Unit: mm

347.66 mm (W) x 106.9 mm (H) x 233.29 mm (D)

Ceiling mount installation

63.50mm [2.5"]

mm [3.85"]

98.00

136.000mm [5.35"]

60.00mm

[2.36"]

mm [3.85"]

98.00

49

Timing chart

Analog RGB

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

VGA 640 x 480 4:3 60/72/75/85

SVGA 800 x 600 4:3 60/72/75/85

XGA

WXGA

Quad-VGA 1280 x 960 4:3 60/85

SXGA 1280 x 1024 5:4 60

SXGA+ 1400 x 1050 4:3 60

WXGA+ 1440 x 900 16:10 60

UXGA 1600 x 1200 4:3 60

WSXGA+ 1680 x 1050 16:10 60

HD 1280 x 720 16:9 60

MAC 13" 640 x 480 4:3 67

1024 x 768 4:3 60/70/75/85
1152 x 864 4:3 75
1280 x 768 15:9 60
1280 x 800 16:10 60/75/85
1360 x 768 16:9 60

MAC 16" 832 x 624 4:3 75
MAC 19" 1024 x 768 4:3 75
MAC 21" 1152 x 870 4:3 75

HDTV (1080p) 1920 x 1080 16:9 60

50

HDMI

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

VGA 640 x 480 4:3 60

SVGA 800 x 600 4:3 60

XGA 1024 x 768 4:3 60

1280 x 768 15:9 60

WXGA

Quad-VGA 1280 x 960 4:3 60

SXGA 1280 x 1024 5:4 60

SXGA+ 1400 x 1050 4:3 60

WXGA+ 1440 x 900 16:10 60

WSXGA+ 1680 x 1050 16:10 60

HDTV (1080p) 1920 x 1080 16:9 50 / 60

HDTV (1080i) 1920 x 1080 16:9 50 / 60
HDTV (720p) 1280 x 720 16:9 50 / 60

SDTV (480p) 720 x 480 4:3 / 16:9 60
SDTV (576p) 720 x 576 4:3 / 16:9 50

SDTV (480i) 720 x 480 4:3 / 16:9 60
SDTV (576i) 720 x 576 4:3 / 16:9 50

1280 x 800 16:10 60
1360 x 768 16:9 60

51

3D (HDMI signal included)

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
SVGA 800 x 600 4:3 60* / 120**

XGA 1024 x 768 4:3 60* / 120**

HD 1280 x 720 16:9 60* / 120**

WXGA 1280 x 800 16:9 60* / 120**

for Video Signal

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

SDTV (480i)*** 720 x 480 4:3 / 16:9 60

60Hz signals are supported for

*
** 120 Hz signals are supported for Frame Sequential format only.
*** Video signal (SDTV 480i) is supported for Frame Sequential format only.

Side-by-Side, Top-Bottom

, and

Frame Sequential

HDMI 3D

In Frame packing format

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
1080p 1920 x 1080 16:9 23.98/24

720p 1280 x 720 16:9 50/59.94/60

In Side by side format

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

formats.

1080i 1920 x 1080 16:9 50/59.94/60

In Top and Bottom format

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
1080p 1920 x 1080 16:9 23.98/24

720p 1280 x 720 16:9 50/59.94/60

52

Component video

Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)

HDTV (1080p) 1920 x 1080 16:9 50 / 60

HDTV (1080i) 1920 x 1080 16:9 50 / 60

HDTV (720p) 1280 x 720 16:9 50 / 60
SDTV (480p) 720 x 480 4:3 / 16:9 60
SDTV (576p) 720 x 576 4:3 / 16:9 50

SDTV (480i) 720 x 480 4:3 / 16:9 60
SDTV (576i) 720 x 576 4:3 / 16:9 50

Composite video

Signal Aspect Ratio Refresh Rate (Hz)
NTSC 4:3 60

PAL 4:3 50

PAL60 4:3 60

SECAM 4:3 50

53

Copyright information

Copyright

Copyright 2015. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.

Disclaimer

ViewSonic Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, ViewSonic Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.

*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.

54

Appendix

IR control table

Key

(with Blue back light)

Power ON NEC X3 F4 4F A0

Power Off NEC X3 F4 4E A1

COMP NEC X3 F4 41 BE
HDMI 1 NEC X3 F4 58 A7
HDMI 2 NEC X3 F4 59 A6

Auto sync NEC X3 F4 8 F7

Source NECX3F440BF

Up/V keystone + NEC X3 F4 0B F4

Left NECX3F40EF1
Enter NEC X3 F4 15 EA
Right NEC X3 F4 0F F0

Down/V keystone - NEC X3 F4 0C F3

Menu NEC X3 F4 30 CF
Info(i) NEC X3 F4 97 68

Exit NEC X3 F4 28 D7

Aspect NEC X3 F4 13 EC

Pattern NEC X3 F4 55 AA

Blank NEC X3 F4 7 F8

Help(?) NEC X3 F4 21 DE

Mute NEC X3 F4 14 EB

Volume- NEC X3 F4 83 7C

Volume+ NEC X3 F4 82 7D

Brightness NEC X3 F4 60 9F

Contrast NEC X3 F4 61 9E

Color Temp. NEC X3 F4 66 99

3D NEC X3 F4 20 DF

Standard NEC X3 F4 62 9D

Gaming NECX3F4639C

Eco mode/ ID6 NEC X3 F4 2B D4

Movie NEC X3 F4 64 9B

Sports NEC X3 F4 65 9A

Format Byte1 Byte2 Byte3 Byte4

55

RS232 command table

<Pin assignment for this two end>

Pin Description Pin Description

1NC2RX
3TX4NC
5GND6NC
7RTSZ8CTSZ
9NC

<Interface>

Baud Rate 115200 bps (default)

Data Length 8 bit

Parity Check None

Stop Bit 1 bit

Flow Control None

RS-232 protocol

56

<RS232 command table>

Function Type Action Command

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x00 0x00 0x5D

0x01 0x00 0x5E

0x00 0x11 0x00 0x5E

0x02 0x00 0x5F

0x2A 0x00 0x87

0x0A 0x00 0x67

0x0A 0x01 0x68

0x0A 0x02 0x69

0x00 0x11 0x0A 0x68

0x0B 0x00 0x68

0x0B 0x01 0x69

0x00 0x11 0x0B 0x69

0x0C 0x00 0x69

0x0C 0x01 0x6A

0x00 0x11 0x0C 0x6A

0x10 0x00 0x6D

0x10 0x01 0x6E

0x10 0x02 0x6F

0x10 0x03 0x70

0x00 0x11 0x10 0x6E

Power

Reset All

Settings

Reset Color

Settings

Splash

Screen

Quick Power

Off

High Altitude

Mode

Lamp Mode

ON

Write

OFF

Read Status

Write Execute

Write Execute

Black

Write

Read Status

Write

Read Status

Write

Read Status

Write

Read Status

Blue

ViewSonic

OFF

ON

OFF

ON

Normal

Eco

Dynamic

SuperEco

57

Function Type Action Command

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x27 0x00 0x84

0x27 0x01 0x85

0x00 0x11 0x27 0x85

0x00 0x00 0x5E

0x00 0x01 0x5F

0x00 0x02 0x60

0x00 0x03 0x61

0x00 0x12 0x00 0x5F

0x20 0x00 0x7E

0x20 0x01 0x7F

0x20 0x02 0x80

0x20 0x03 0x81

0x20 0x04 0x82

0x20 0x05 0x83

0x00 0x12 0x20 0x7F

0x21 0x00 0x7F

0x21 0x01 0x80

0x00 0x12 0x21 0x80

0x02 0x00 0x60

0x02 0x01 0x61

0x00 0x12 0x02 0x61

Message

Projector

Position

3D Sync

3D Sync

Invert

Contrast

OFF

Write

ON

Read Status

Front Table

Rear Table

Write

Rear Ceiling

Front Ceiling

Read Status

OFF

Auto

Frame Sequential

Write

Frame Packing

Top Bottom

Side by Side

Read Status

OFF

Write

ON

Read Status

Decrease

Write

Increase

Read Get Value

58

Function Type Action Command

Decrease

Write

Brightness

Read Get Value

Write

Aspect ratio

Read Get Value

Auto Adjust Write Execute

Horizontal

position

Vertical

position

Color

temperature

Write

Read Get Value

Write

Read Get Value

Write

Read Get Value

Increase

Auto

4:3

16:9

Anamorphic

2.35:1

Panorama

Cycle

Shift Right

Shift Left

Shift Up

Shift Down

Warm

Normal

Cool

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x03 0x00 0x61

0x03 0x01 0x62

0x00 0x12 0x03 0x62

0x04 0x00 0x62

0x04 0x02 0x64

0x04 0x03 0x65

0x04 0x05 0x67

0x04 0x07 0x69

0x04 0x08 0x6A

0x31 0x00 0x90

0x00 0x12 0x04 0x63

0x05 0x00 0x63

0x06 0x01 0x65

0x06 0x00 0x64

0x00 0x12 0x06 0x65

0x07 0x00 0x65

0x07 0x01 0x66

0x00 0x12 0x07 0x66

0x08 0x00 0x66

0x08 0x01 0x67

0x08 0x03 0x69

0x00 0x12 0x08 0x67

59

Function Type Action Command

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x09 0x01 0x68

0x09 0x00 0x67

0x00 0x12 0x09 0x68

0x0A 0x00 0x68

0x0A 0x01 0x69

0x00 0x12 0x0A 0x69

0x0B 0x00 0x69

0x0B 0x09 0x72

0x0B 0x04 0x6D

0x0B 0x11 0x7A

0x0B 0x12 0x7B

0x33 0x00 0x92

0x00 0x12 0x0B 0x6A

0x10 0x00 0x6E

0x10 0x01 0x6F

0x10 0x02 0x70

0x10 0x03 0x71

0x10 0x04 0x72

0x10 0x05 0x73

0x00 0x12 0x10 0x6F

Blank

Keystone-

Vertical

Color mode

Primary

Color

ON

Write

OFF

Read Status

Decrease

Write

Increase

Read Get value

Brightest

Movie (Rec 709)

Standard

Write

Sports

Gaming

Cycle

Read Status

R

G

B

Write

C

M

Y

Read Status

60

Function Type Action Command

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x11 0x00 0x6F

0x11 0x01 0x70

0x00 0x12 0x11 0x70

0x12 0x00 0x70

0x12 0x01 0x71

0x00 0x12 0x12 0x71

0x13 0x00 0x71

0x13 0x01 0x72

0x00 0x12 0x13 0x72

0x0E 0x00 0x6C

0x0E 0x01 0x6D

0x00 0x12 0x0E 0x6D

0x00 0x01 0x60

0x00 0x00 0x5F

0x00 0x13 0x00 0x60

0x01 0x00 0x60

0x01 0x03 0x63

0x01 0x07 0x67

0x01 0x05 0x65

0x00 0x13 0x01 0x61

Hue

Saturation

Gain

Sharpness

Freeze

Source input

Decrease

Write

Increase

Read Get value

Decrease

Write

Increase

Read Get value

Decrease

Write

Increase

Read Get value

Decrease

Write

Increase

Read Get value

ON

Write

OFF

Read Status

D-Sub / Comp. 1

HDMI 1

Write

HDMI 2

Composite Video

Read Status

61

Function Type Action Command

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x14

0x06 0x14 0x00 0x04 0x00 0x34 0x14

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x14

0x06 0x14 0x00 0x04 0x00 0x34 0x14

0x06 0x14 0x00 0x04 0x00 0x34 0x13

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x02 0x01 0x62

0x02 0x00 0x61

0x00 0x13 0x02 0x62

0x00 0x01 0x61

0x00 0x00 0x60

0x00 0x14 0x00 0x61

0x01 0x00 0x61

0x02 0x00 0x62

0x2A 0x11 0x9A

0x00 0x14 0x03 0x64

Quick Auto

Search

Mute

Volume

ON

Write

OFF

Read Status

ON

Write

OFF

Read Status

Increse

Write

Read Get Value

Decrese

Write Value

62

Function Type Action Command

Language Write

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x00 0x00 0x61

0x00 0x01 0x62

0x00 0x02 0x63

0x00 0x03 0x64

0x00 0x04 0x65

0x00 0x05 0x66

0x00 0x06 0x67

0x00 0x07 0x68

0x00 0x08 0x69

0x00 0x09 0x6A

0x00 0x0a 0x6B

0x00 0x0b 0x6C

0x00 0x0c 0x6D

63

Function Type Action Command

Language

Lamp Hours

Reset

HDMI Format

HDMI Range

Write

Vie

Read Status

Write Reset to ZERO

Read Get Usage Time

RGB

Write

Read Status

Write

Read Status

YUV

Auto

Enhanced

Normal

Auto

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x15

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x00 0x0d 0x6E

0x00 0x0e 0x6F

0x00 0x0f 0x70

0x00 0x10 0x71

0x00 0x11 0x72

0x00 0x12 0x73

0x00 0x13 0x74

0x00 0x14 0x75

0x00 0x15 0x76

0x00 0x15 0x00 0x62

0x01 0x00 0x62

0x00 0x15 0x01 0x63

0x28 0x00 0x85

0x28 0x01 0x86

0x28 0x02 0x87

0x00 0x11 0x28 0x86

0x29 0x00 0x86

0x29 0x01 0x87

0x29 0x02 0x88

0x00 0x11 0x29 0x87

64

Function Type Action Command

OFF

Write

CEC

Read Status

Error status Read Status

Write

Brilliant Color

Read Status

Remote

Control Code

Write

ON

OFF

Color 1

Color 2

Color 3

Color 4

Color 5

Color 6

Color 7

Color 8

Color 9

Color 10

code 1

code 2

code 3

code 4

code 5

code 6

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x06 0x14 0x00 0x04 0x00 0x34 0x12

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x0C

0x06 0x14 0x00 0x04 0x00 0x34 0x0C

0x06 0x14 0x00 0x04 0x00 0x34 0x0C

0x06 0x14 0x00 0x04 0x00 0x34 0x0C

0x06 0x14 0x00 0x04 0x00 0x34 0x0C

0x06 0x14 0x00 0x04 0x00 0x34 0x0C

0x2B 0x00 0x88

0x2B 0x01 0x89

0x00 0x11 0x2B 0x89

0x00 0x0C 0x0D 0x66

0x0F 0x00 0x6D

0x0F 0x01 0x6E

0x0F 0x02 0x6F

0x0F 0x03 0x70

0x0F 0x04 0x71

0x0F 0x05 0x72

0x0F 0x06 0x73

0x0F 0x07 0x74

0x0F 0x08 0x75

0x0F 0x09 0x76

0x0F 0x0A 0x77

0x00 0x12 0x0F 0x6E

0x48 0x00 0xA0

0x48 0x01 0xA1

0x48 0x02 0xA2

0x48 0x03 0xA3

0x48 0x04 0xA4

0x48 0x05 0xA5

65

Function Type Action Command

0x06 0x14 0x00 0x04 0x00 0x34 0x0C

0x06 0x14 0x00 0x04 0x00 0x34 0x0C

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x06 0x14 0x00 0x04 0x00 0x34 0x11

0x07 0x14 0x00 0x05 0x00 0x34 0x00

0x48 0x06 0xA6

0x48 0x07 0xA7

0x00 0x0C 0x48 0xA1

0x32 0x00 0x8F

0x32 0x01 0x90

0x32 0x02 0x91

0x32 0x03 0x92

0x00 0x11 0x32 0x90

0x33 0x00 0x90

0x33 0x01 0x91

0x33 0x02 0x92

0x33 0x03 0x93

0x33 0x04 0x94

0x33 0x05 0x95

0x00 0x11 0x33 0x91

Remote

Control code

Screen Color

Over Scan

code 7

Write

code 8

Read Status

OFF

Blackboard

Write

Greenboard

Whiteboard

Read Status

OFF

Value 1

Value 2

Write

Value 3

Value 4

Value 5

Read Get Value

66

Function Type Action Command

Menu

Exit

Top

Bottom

Remote Key Write

AMX Write AMX response AMX

Left

Right

Source

Enter

Auto

0x02 0x14 0x00 0x04 0x00 0x34 0x02

0x02 0x14 0x00 0x04 0x00 0x34 0x02

0x02 0x14 0x00 0x04 0x00 0x34 0x02

0x02 0x14 0x00 0x04 0x00 0x34 0x02

0x02 0x14 0x00 0x04 0x00 0x34 0x02

0x02 0x14 0x00 0x04 0x00 0x34 0x02

0x02 0x14 0x00 0x04 0x00 0x34 0x02

0x02 0x14 0x00 0x04 0x00 0x34 0x02

0x02 0x14 0x00 0x04 0x00 0x34 0x02

0x04 0x0F 0x61

0x04 0x13 0x65

0x04 0x0B 0x5D

0x04 0x0C 0x5E

0x04 0x0D 0x5F

0x04 0x0E 0x60

0x04 0x04 0x56

0x04 0x15 0x67

0x04 0x08 0x5A

67

Customer Support

For technical support or product service, see the table below or contact your reseller.

Note : You will need the product serial number.

Country/Region Website

Australia
New Zealand

Canada www.viewsonic.com T= 1-866-463-4775 [e-mail]
Europe www.viewsoniceurope.com http://www.viewsoniceurope.com/eu/support/call-desk/
Hong Kong www.hk.viewsonic.com T= 852 3102 2900 [e-mail]
India www.in.viewsonic.com T= 1800 419 0959 [e-mail]
Korea ap.viewsonic.com/kr/ T= 080 333 2131 [e-mail]
Latin America

(Argentina)
Latin America

(Chile)
Latin America

(Columbia)
Latin America

(Mexico)
Nexus Hightech Solutions, Cincinnati #40 Desp. 1 Col. De los Deportes Mexico D.F.

Tel: [phone])6547-6484
Other places please refer to http://www.viewsonic.com/la/soporte/servicio-tecnico#mexico

Latin America
(Peru)

Macau www.hk.viewsonic.com T= 853-2840-3687 [e-mail]
Middle East ap.viewsonic.com/me/ Contact your reseller [e-mail]

Puerto Rico &
Virgin Islands

Singapore/
Malaysia/Thailand

South Africa ap.viewsonic.com/za/ Contact your reseller [e-mail]
United States www.viewsonic.com T= 1-800-688-6688 [e-mail]

www.viewsonic.com.au

www.viewsonic.com/la/

www.viewsonic.com/la/

www.viewsonic.com/la/

www.viewsonic.com/la/

www.viewsonic.com/la/

www.viewsonic.com

www.ap.viewsonic.com T= 65 6461 6044 [e-mail]

T= Telephone
C = CHAT ONLINE

AUS= 1800 880 818
NZ= 0800 008 822

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

T= 1-800-688-6688 (English)
C= http://www.viewsonic.com/

la/soporte/servicio-tecnico

Email

[e-mail]

[e-mail]

[e-mail]

[e-mail]

[e-mail]

[e-mail]

[e-mail]
[e-mail]

68

Limited Warranty

ViewSonic® Projector

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product proves to
be defective in material or workmanship during the warranty period, ViewSonic will,
at its sole option, repair or replace the product with a like product. Replacement
product or parts may include remanufactured or refurbished parts or components.

Limited Three (3) year General Warranty

Subject to the more limited one (1) year warranty set out below, North and South
America: Three (3) years warranty for all parts excluding the lamp, three (3) years

IRUODERUDQGRQH\HDUIRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHU

purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic

RI¿FHIRUWKHZDUUDQW\LQIRUPDWLRQ

Limited One (1) year Heavy Usage Warranty:

Under heavy usage settings, where a projector’s use includes more than fourteen
(14) hours average daily usage, North and South America: One (1) year warranty
for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the

RULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH(XURSH2QH\HDU

warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days

IRUWKHRULJLQDOODPSIURPWKHGDWHRIWKH¿UVWFRQVXPHUSXUFKDVH

Other regions or countries: Please check with your local dealer or local ViewSonic

RI¿FHIRUWKHZDUUDQW\LQIRUPDWLRQ
/DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWR

manufacturer’s installed lamp only. All accessory lamps purchased separately are
warranted for 90 days.

Who the warranty protects:

7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU

What the warranty does not cover:

$Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG

2. Damage, deterioration, failure, or malfunction resulting from:

D$FFLGHQWDEXVHPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUH

LPSURSHUPDLQWHQDQFHXQDXWKRUL]HGSURGXFWPRGL¿FDWLRQRUIDLOXUHWRIROORZ

instructions supplied with the product.

E2SHUDWLRQRXWVLGHRISURGXFWVSHFL¿FDWLRQV

c. Operation of the product for other than the normal intended use or not under

normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.

J&DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFSRZHUÀXFWXDWLRQVRUIDLOXUH
K8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV

i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.

3. Removal, installation, and set-up service charges.

69

How to get service:

1. For information about receiving service under warranty, contact ViewSonic
Customer Support (please refer to “Customer Support” page). You will need to
provide your product’s serial number.

2. To obtain warranted service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a description of the problem, and
(e) the serial number of the product.

3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.

4. For additional information or the name of the nearest ViewSonic service center,
contact ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description

FRQWDLQHGKHUHLQLQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUD

particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based

XSRQLQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRI

business opportunity, loss of goodwill, interference with business relationships, or
other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

Effect of local law:

7KLVZDUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWV

which vary from local authority. Some local governances do not allow limitations on
implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic products sold outside of the
U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and
Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.

Projector Warranty Term Template In UG
VSC_TEMP_2005

70

Mexico Limited Warranty

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.

How long the warranty is effective:

3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of

WKH¿UVWFRQVXPHUSXUFKDVH
/DPSZDUUDQW\VXEMHFWWRWHUPVDQGFRQGLWLRQVYHUL¿FDWLRQDQGDSSURYDO$SSOLHVWRPDQXIDFWXUHU¶V

installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.

Who the warranty protects:

7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU

What the warranty does not cover:

 $Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG

2. Damage, deterioration or malfunction resulting from:

D$FFLGHQWPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUHXQDXWKRUL]HGSURGXFW

PRGL¿FDWLRQXQDXWKRUL]HGDWWHPSWHGUHSDLURUIDLOXUHWRIROORZLQVWUXFWLRQVVXSSOLHGZLWKWKH

product.

b. Any damage of the product due to shipment.

F&DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFDOSRZHUÀXFWXDWLRQVRUIDLOXUH
G8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV

e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.

3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.

4. Removal, installation, insurance, and set-up service charges.

How to get service:

For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to the attached Customer Support page). You will need to provide your product’s serial number,
so please record the product information in the space provided below on your purchase for your future
use. Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: ____________________________
Document Number: ____________________ Serial Number: ____________________________
Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? __________

1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

2. Take or ship the product in the original container packaging to an authorized ViewSonic service
center.

3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein

LQFOXGLQJWKHLPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUDSDUWLFXODUSXUSRVH

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:

1. Damage to other property caused by any defects in the product, damages based upon

LQFRQYHQLHQFHORVVRIXVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRIEXVLQHVVRSSRUWXQLW\

loss of goodwill, interference with business relationships, or other commercial loss, even if advised
of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

4. Repair or attempted repair by anyone not authorized by ViewSonic.

ViewSonic® Projector

71

Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:

Name, address, of manufacturer and importers:

México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: [phone] http://www.viewsonic.com/la/soporte/index.htm

NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004

Hermosillo:

Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: [phone]
E-Mail: [e-mail]

Puebla, Pue. (Matriz):

RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: [phone] CON 10 LINEAS
E-Mail: [e-mail]

Chihuahua

Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: [phone]
E-Mail: [e-mail]

Distrito Federal:

QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: [phone]
E-Mail : [e-mail]

Guerrero Acapulco

GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: [phone]

MERIDA:

ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: [phone]
E-Mail: [e-mail]

Tijuana:

STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico

Villahermosa:

Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: [phone]
E-Mail: [e-mail]

Veracruz, Ver.:

CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: [phone]
E-Mail: [e-mail]

Cuernavaca

Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: [phone]
E-Mail: [e-mail]

Guadalajara, Jal.:

SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: [phone]
E-Mail: [e-mail]

Monterrey:

Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: [phone]
E-Mail: [e-mail]

Oaxaca, Oax.:

CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: [phone]
Fax: [phone]
E-Mail. [e-mail]

FOR USA SUPPORT:

ViewSonic Corporation
14035 Pipeline Ave. Chino, CA 91710, USA
Tel: [phone]
E-Mail: http://www.viewsonic.com

Projector Mexico Warranty Term Template In UG
VSC_TEMP_2006

72