ViewSonic Pro9800WUL, Pro9520WL, Pro9510L User Manual
Pro9510L/Pro9520WL/
Pro9530HDL/Pro9800WUL
DLP Projector
User Guide
IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specic languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Model No. VS16505/VS16506/VS16507/VS16508
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
y Reorient or relocate the receiving antenna.
y Increase the separation between the equipment and receiver.
y Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
y Consult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly approved
by the party responsible for compliance could void your authority to operate the
equipment.
For Canada
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2012/19/EU (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,
0.002% Cadmium, or more than 0.004% Lead.
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
prong are provided for your safety. If the provided plug does not t into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by
the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Substance
Lead (Pb) 0.1% < 0.1%
Mercury (Hg) 0.1% < 0.1%
Cadmium (Cd) 0.01% < 0.01%
6+
Hexavalent Chromium (Cr
Polybrominated biphenyls (PBB) 0.1% < 0.1%
Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%
) 0.1% < 0.1%
Proposed Maximum
Concentration
Actual Concentration
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode uorescent lamps and external electrode uorescent
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (＞500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (＞1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
Copyright Information
Copyright © ViewSonic® Corporation, 2016. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks
of Microsoft Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered
trademarks of ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association.
DPMS and DDC are trademarks of VESA.
PS/2, VGA and XGA are registered trademarks of International Business Machines
Corporation.
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors
or omissions contained herein; nor for incidental or consequential damages resulting
from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves
the right to change product specications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means,
for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
The ViewSonic CD also provides an opportunity for you to print the product
registration form. Upon completion, please mail or fax to a respective ViewSonic
office. To find your registration form, use the directory “:\CD\Registration”.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
For additional information, please see the “Customer Support” section in this guide.
For Your Records
Product Name: Pro9510L/Pro9520WL/Pro9530HDL/Pro9800WUL
ViewSonic DLP Projector
Model Number: VS16505_VS16506/VS16507_VS16508
Document Number: Pro9510L/Pro9520WL/Pro9530HDL/Pro9800WUL_UG_
ENG Rev. 1A 07-29-16
Serial Number: ________________________________________
Purchase Date: ________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the
environment. Please use care and dispose of in accordance with local, state or
federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/uk/support/recycling-information/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
i
Copyright
Ver.:01
This publication, including all photographs, illustrations and software, is protected under international
copyright laws, with all rights reserved. Neither this manual, nor any of the material contained herein, may
be reproduced without written consent of the author.
© Copyright 2016
Disclaimer
The information in this document is subject to change without notice. The manufacturer makes no
representations or warranties with respect to the contents hereof and specifically disclaims any implied
warranties of merchantability or fitness for any particular purpose. The manufacturer reserves the right to
revise this publication and to make changes from time to time in the content hereof without obligation of
the manufacturer to notify any person of such revision or changes.
Trademark Recognition
Kensington is a U.S. registered trademark of ACCO Brand Corporation with issued registrations
and pending applications in other countries throughout the world.
HDMI, the HDMI Logo, and High-Definition Multimedia Interface are trademarks or
registered trademarks of HDMI Licensing LLC in the United States and other countries.
MHL, the MHL logo, and Mobile High-Definition Link are trademarks or registered
trademarks of MHL licensing, LCC.
All other product names used in this manual are the properties of their respective owners and are
acknowledged.
ii
Important Safety Information
Important:
It is strongly recommended that you read this section carefully before using the projector. These
safety and usage instructions will ensure that you enjoy many years of safe use of the projector.
Keep this manual for future reference.
Symbols Used
Warning symbols are used on the unit and in this manual to alert you of hazardous situations.
The following styles are used in this manual to alert you to important information.
Note:
Provides additional information on the topic at hand.
Important:
Provides additional information that should not be overlooked.
Caution:
Alerts you to situations that may damage the unit.
Warning:
Alerts you to situations that may damage the unit, create a hazardous environment, or cause
personal injury.
Throughout this manual, component parts and items in the OSD menus are denoted in bold font as in this
example:
“Push the Menu button on the remote control to open the Main menu.”
General Safety Information
Do not open the unit case. Aside from the projection lamp, there are no user-serviceable parts in
the unit. For servicing, contact qualified service personnel.
Follow all warnings and cautions in this manual and on the unit case.
The projection lamp is extremely bright by design. To avoid damage to eyes, do not look into the
lens when the lamp is on.
Do not place the unit on an unstable surface, cart, or stand.
Avoid using the system near water, in direct sunlight, or near a heating device.
Do not place heavy objects such as books or bags on the unit.
iii
Projector Installation Notice
Minimum 500mm
(19.69 inch)
Minimum 500mm
(19.69 inch)
Minimum 500mm
(19.69 inch)
Minimum 500mm
(19.69 inch)
Minimum 300mm
(11.81 inch)
Do not tilt the projector to the left or right, otherwise lamp life could decrease dramatically, and
may lead to other unpredictable damages.
There is no limit on the tilt angle upward or downward.
Allow at least 50 cm clearance around the exhaust vent.
Ensure that the intake vents do not recycle hot air from the exhaust vent.
When operating the projector in an enclosed space, ensure that the surrounding air temperature
within the enclosure does not exceed operation temperature while the projector is running, and the
air intake and exhaust vents are unobstructed.
All enclosures should pass a certified thermal evaluation to ensure that the projector does not
recycle exhaust air, as this may cause the device to shutdown even if the enclosure temperature is
with the acceptable operation temperature range.
iv
Verify Installation Location
For Australia and
Mainland China
For the U.S.A. and
Canada
For the U.K.
Ground
For Continental Europe
Ground
Ground
Ground
To supply power, the 3-blade (with earthing lead) socket should be used to ensure proper
grounding and equalized ground potential for all of the equipment in the Projector System.
The power code provided with the Projector should be used. In case of any missing item, other
qualified 3-blade (with earthing lead) power cord can be used as substitution; however, do not use
2-blade power cord.
Verify if the voltage is stable, grounded properly and there is no electricity leakage.
Measure total power consumption which should not higher the safety capacity and avoid safety
issue and short circuit.
Turn on Altitude Mode when located in high altitude areas
The projector can only be installed upright or inverted.
When installation the bracket, make sure the weight limit is not exceed and firmly secured.
Avoid installing near air conditioner duct or subwoofer.
Avoid installing at high temperature, insufficient cooling and heavy dust locations.
Keep your product away from fluorescent lamps (>1 Meter) to avoid malfunction
caused by IR interference
The VGA IN connector should be connected to the VGA IN port. Note that it should be inserted
tightly, with the screws on both sides securely fastened to ensure proper connection of the signal
wire for achieving optimal display effect.
The AUDIO IN connector should be connected to the AUDIO IN port and CANNOT be connected
to AUDIO OUT or other ports like BNC, RCA; otherwise, it will lead to mute output and even
DAMAGE the port.
Install the projector above 200cm to avoid damage.
The power cord and signal cable should be connected before power on the projector. During the
projector starting and operating process, DO NOT insert or remove the signal cable or the power
cord to avoid damaging the projector.
Cooling notes
Air outlet
Make sure the air outlet is 50cm clear of any obstruction to ensure proper cooling.
Air outlet location should not be in front of the lens of other projector to avoid causing illusions.
Keep the outlet at least 100cm away from the inlets of other projectors
The projector generates a massive amount of heat during use. The internal fan dissipates the heat
of the projector when shutting down, and such process may continue for a certain period. After the
project enters STANDBY MODE status, press the AC power button to turn off the projector and
remove the power cord. DO NOT remove the power cord during the shutdown process, as it may
cause damage to the projector. In the meantime, the delayed heat radiating will also affect the
service life of the projector. The shutdown process may vary depending on the model used.
Whatever the case may be, be sure to disconnect the power cord till after the projector enters the
STANDBY status.
Air inlet
Make sure there is no object blocking air input within 30 cm.
Keep the inlet away from other heat sources
Avoided heavy dust area
v
Power Safety
DISPOSAL: Do not use household or municipal waste collection services for
disposal of electrical and electronic equipment. EU countries require the use
of separate recycling collection services.
Only use the supplied power cord.
Do not place anything on the power cord. Place the power cord where it will not be in the way of
foot traffic.
Remove the batteries from the remote control when storing or not in use for a prolonged period.
Replacing the Lamp
Replacing the lamp can be hazardous if done incorrectly. See Replacing the Projection Lamp on page 55
for clear and safe instructions for this procedure. Before replacing the lamp:
Unplug the power cord.
Allow the lamp to cool for about one hour.
Cleaning the Projector
Unplug the power cord before cleaning. See Resetting the Lamp Time page 58.
Allow the lamp to cool for about one hour.
Regulatory Warnings
Before installing and using the projector, read the regulatory notices in the Regulatory Compliance on
page 75.
Important Recycle Instructions:
Lamp(s) inside this product contain mercury. This product may contain other electronic waste that
can be hazardous if not disposed of properly. Recycle or dispose in accordance with local, state, or federal
Laws. For more information, contact the Electronic Industries Alliance at WWW.EIAE.ORG. For lamp
specific disposal information check WWW.LAMPRECYCLE.ORG.
Symbol Explanations
vi
Main Features
Compatible with all major video standards including NTSC, PAL, and SECAM.
A high brightness rating allows for presentations in daylight or in lit rooms.
Flexible setup allows for front, rear projections.
Line-of-vision projections remain square, with advanced keystone correction for angled
projections.
Input source automatically detected.
High brightness for projection in just about any environment.
Supports resolutions up to WUXGA for clear and crisp images.
DLP® and BrilliantColor™ technologies from Texas Instruments.
Centered lens for easy installation.
Horizontal and vertical lens shift.
MHL device compatibility for streaming of video and audio content from a compatible
mobile device.
Built-in speaker with multiple audio-in and audio-out ports.
Network ready for integration and system administration via RJ45.
Sealed engine to minimizing the impact of dust and smoke.
Top sided lamp cover for simple lamp removal and insertion.
Anti-theft security features include: Kensington security slot, security bar.
About this Manual
This manual is intended for end users and describes how to install and operate the DLP projector.
Wherever possible, relevant information—such as an illustration and its description—has been kept on
one page. This printer-friendly format is both for your convenience and to help save paper, thereby
protecting the environment. It is suggested that you only print sections that are relevant to your needs.
vii
Table of Contents
GETTING STARTED .............................................................................................................................................. 1
PACKING CHECKLIST ............................................................................................................................................. 1
VIEWS OF PROJECTOR PARTS ................................................................................................................................ 2
Front-right View ............................................................................................................................................... 2
Top view—On-Screen Display (OSD) buttons and LEDs ............................................................................... 3
Rear view ......................................................................................................................................................... 4
Bottom view ..................................................................................................................................................... 6
REMOTE CONTROL PARTS ..................................................................................................................................... 7
Remote control code ....................................................................................................................................... 9
Using the remote mouse control ................................................................................................................... 10
REMOTE CONTROL OPERATING RANGE ................................................................................................................ 10
PROJECTOR AND REMOTE CONTROL BUTTONS ..................................................................................................... 10
SETUP AND OPERATION ................................................................................................................................... 11
INSERTING THE REMOTE CONTROL BATTERIES ..................................................................................................... 11
STARTING AND SHUTTING DOWN THE PROJECTOR ................................................................................................ 12
SETTING AN ACCESS PASSWORD (SECURITY LOCK) .............................................................................................. 14
ADJUSTING THE PROJECTOR LEVEL ..................................................................................................................... 16
ADJUSTING PROJECTED IMAGE POSITION USING LENS SHIFT ................................................................................ 17
Adjusting the vertical image position ............................................................................................................. 18
Adjusting the horizontal image position ......................................................................................................... 20
ADJUSTING THE ZOOM, FOCUS AND KEYSTONE ..................................................................................................... 21
ADJUSTING THE VOLUME ..................................................................................................................................... 22
ON-SCREEN DISPLAY (OSD) MENU SETTINGS.............................................................................................. 23
OSD MENU CONTROLS ....................................................................................................................................... 23
Navigating the OSD ....................................................................................................................................... 23
SETTING THE OSD LANGUAGE ............................................................................................................................. 24
OSD MENU OVERVIEW ........................................................................................................................................ 25
IMAGE MENU ....................................................................................................................................................... 28
Advanced Feature ......................................................................................................................................... 29
DISPLAY MENU .................................................................................................................................................... 32
VIDEO/AUDIO MENU ............................................................................................................................................ 33
Audio.............................................................................................................................................................. 34
BASIC MENU ....................................................................................................................................................... 35
Splash screen ................................................................................................................................................ 36
HV Keystone .................................................................................................................................................. 36
Advanced Feature ......................................................................................................................................... 37
ADVANCED MENU ................................................................................................................................................ 40
Advanced Feature ......................................................................................................................................... 41
OSD Menu Setting ......................................................................................................................................... 42
Lamp Hour Reset .......................................................................................................................................... 42
3D .................................................................................................................................................................. 43
Network Setting ............................................................................................................................................. 43
Status............................................................................................................................................................. 54
MAINTENANCE AND SECURITY ....................................................................................................................... 55
REPLACING THE PROJECTION LAMP ..................................................................................................................... 55
Resetting the Lamp Time .............................................................................................................................. 58
CLEANING THE PROJECTOR ................................................................................................................................. 59
Cleaning the Lens .......................................................................................................................................... 59
Cleaning the Case ......................................................................................................................................... 59
Cleaning the Air Filter .................................................................................................................................... 60
USING THE PHYSICAL LOCK ................................................................................................................................. 62
Using the Kensington Security Slot ............................................................................................................... 62
Using the Security Bar Lock .......................................................................................................................... 62
TROUBLESHOOTING ......................................................................................................................................... 63
COMMON PROBLEMS AND SOLUTIONS .................................................................................................................. 63
TIPS FOR TROUBLESHOOTING .............................................................................................................................. 63
viii
LED ERROR MESSAGES ...................................................................................................................................... 64
IMAGE PROBLEMS ............................................................................................................................................... 65
LAMP PROBLEMS ................................................................................................................................................. 65
REMOTE CONTROL PROBLEMS ............................................................................................................................. 66
AUDIO PROBLEMS ............................................................................................................................................... 66
HAVING THE PROJECTOR SERVICED ..................................................................................................................... 66
HDMI Q & A ....................................................................................................................................................... 67
SPECIFICATIONS ................................................................................................................................................ 68
SPECIFICATIONS .................................................................................................................................................. 68
PROJECTION DISTANCE VS. PROJECTION SIZE ...................................................................................................... 70
PRO9510L / PRO9520WL / PRO9530HDL / PRO9800WUL ....................................................................... 70
TIMING MODE TABLE ........................................................................................................................................... 72
PROJECTOR DIMENSIONS .................................................................................................................................... 74
REGULATORY COMPLIANCE ........................................................................................................................... 75
FCC WARNING ................................................................................................................................................... 75
CANADA .............................................................................................................................................................. 75
SAFETY CERTIFICATIONS ..................................................................................................................................... 75
APPENDIX I ......................................................................................................................................................... 76
IR CODE TABLE .................................................................................................................................................... 76
APPENDIX II ........................................................................................................................................................ 77
RS-232C PROTOCOL .......................................................................................................................................... 77
1
Projector
Remote Control
(Batteries Included)
VGA Cable
Power Cord
CD-ROM
(This User's Manual)
Quick Start Guide
Packing Checklist
Carefully unpack the projector and check that the following items are included:
GETTING STARTED
Contact your dealer immediately if any items are missing, appear damaged, or if the unit does not work. It is
recommend that you keep the original packing material should you ever need to return the equipment for
warranty service.
Caution:
Avoid using the projector in dusty environments.
2
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
Lamp Cover
Remove cover to replace lamp.
55
2.
Tilt Adjuster
Rotate adjuster lever to adjust angle position.
14
3.
Lens
Projection Lens.
4.
IR Receiver
Receives IR signal from remote control.
7
5.
LEDs
Displays the projector status.
3
6.
Vent
Cool air intake.
60
7.
Vertical Lens Shift
Adjusts the image position vertically.
18
8.
Horizontal Lens Shift
Adjusts the image position horizontally.
20
9.
Zoom Ring
Enlarges the projected image.
21
10.
Focus Ring
Focuses the projected image.
21
11.
Function Keys
On-Screen Display (OSD) buttons.
3
1 2 3 4 5 2
7
Views of Projector Parts
Front-right View
Important:
Ventilation openings on the projector allow for good air circulation, which keeps the projector lamp
cool. Do not obstruct any of the ventilation openings.
3
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
Power LED
Display the power on/off sequence status.
64
2.
Lamp LED
Display the lamp status.
64
3.
Temp LED
Display the thermal status.
64
4.
Filter LED
Display the filter replacing warning message.
64
5.
Turn the projector on or off.
12
6.
MENU / EXIT
Opens and exits OSD menus.
23
7.
Navigates and changes settings in the OSD.
Quick Menu – For Horizontal Keystone.
23
8.
Navigates and changes settings in the OSD.
Quick Menu – For Vertical Keystone.
23
9.
Enter or confirm highlighted OSD menu item.
Displays the Corner Adj. page.
23
10.
Navigates and changes settings in the OSD.
Quick Menu – For Horizontal Keystone.
23
11.
SOURCE
Enter the Source menu.
23
12.
(My Button)
Allows user to define a short cut key on this button,
and the function item is selected in OSD menu.
23
13.
Navigates and changes settings in the OSD.
Quick Menu – For Vertical Keystone.
23
ZOOM
FOCUS
LENS SHIFT
SOURCE
MENU
EXIT
ENTER
1 2 3 4
5 6 7 8 910 11 12 13
ENTER
Top view—On-Screen Display (OSD) buttons and LEDs
4
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
HDMI 1 /MHL
Connect the HDMI/MHL cable from an HDMI/MHL device.
Note: Set the Source to HDMI 1/MHL also can be charging connected
MHL compatible smart device as long as the projector Power
On.
2.
HDMI 2
Connect the HDMI cable from an HDMI device.
3.
DVI-D
Connect the DVI CABLE to a display.
4.
RS-232
Connects RS-232 serial port cable for remote control.
5.
Computer Out
Connect an RGB cable to a display (Pass through by VGA1 only).
6.
S-VIDEO
Connect a S-VIDEO cable from a video device.
7.
Computer In 1
Connect an RGB cable from a computer or a video enabled device.
8.
BNC
Connect a BNC cable from a computer.
9.
Computer In 2
Connect an RGB cable from a computer or a video enabled device.
10.
RJ45 (LAN)
Connect a LAN cable from Ethernet.
11.
USB
Connect a USB cable for USB host.
Note: Support 5V/1.0A for each port output as long as the projector
Power On.
12.
3D-VESA
Connect 3D IR glasses receiver unit.
13.
Kensington Security Slot
Secures to permanent object with a Kensington Lock
system.
62
14.
AUDIO IN L/R
Connect the audio cables from an audio device for VIDEO or
S-VIDEO audio input.
15.
AUDIO IN
Connect an AUDIO cable from the input device.
16.
IR
Receive IR signal from remote control.
17.
12V OUT
When connected to the screen through a commercially available
cable, the screen deploys automatically on start up of the projector.
The screen retracts when the projector is powered off (see notes
below).
18.
AUDIO OUT
Connect an AUDIO cable for audio loop through.
19.
AUDIO OUT L/R
Connect an AUDIO cable for audio loop through.
20.
VIDEO
Connect the composite cable from a video device.
S-Video
Serv ice
Video RL
Audio
In DVI-DIn1 In2
Audio
In
RL
Audio
OutMIC
Compu ter In 1
RGBHV
Compu ter O ut
LAN
Compu ter In 2 3D VESAUSB
RS 232-
DVI-D
HDMI2HDMI1 MHL/
IRAudioOut
In OutRem ote
Wired
12VOut
1 2 3 4 5 6 7 8 9101112
1
314
15
1
6
17
1
8
19
2
0
21
2
2
23
2
4
Rear view
5
ITEM
LABEL
DESCRIPTION
SEE PAGE
21.
MICROPHONE
Connect the microphone input device.
22.
SERVICE
For service personnel only.
23.
WIRE REMOTE In / Out
Connect the wire remote from remote control to the projector for wire
remote control.
Connect "WIRE REMOTE OUT" to another projector (same model)
"WIRE REMOTE IN" for serial control.
24.
AC IN
Connect the POWER cable.
S-Video
Serv ice
Video
RL
Audio
In DVI-D In1 In2
Audio
In
RL
Audi o
OutMIC
Comp uter In 1
R G B H V
Comp uter Out
LAN
Comp uter In 2 3D VESAUSB
RS 2 32-
DVI-D
HDMI 2 HDMI 1 M HL /
IRA udioOut
In OutRemote
Wired
12VOut
14
3
13
12
11
10
9
8
5
6
4
7
6
5
4
3
21
1. Composite Video Cable
2. S-Video Cable
3. Audio L/R Cable
4. HDMI Cable
5. VGA Cable
6. VGA to DVI-D Cable
7. RS-232 Cable
8. RJ45 Cable
9. Type-A port power 1A
10. Audio Cable
11. BNC Cable
12. 12V DC jack
13. Audio Cable
14. USB Cable
Note:
To use this feature, you must plug in the connector before turn on/off the projector.
Screen controllers are supplied and supported by screen manufacturers.
Do not use this jack for anything other than intended use.
Warning:
As a safety precaution, disconnect all power to the projector and connecting devices before making
connections.
6
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
Tilt Adjustor
Rotate adjuster lever to adjust angle position.
16
2.
Ceiling Mount Holes
Contact your dealer for information on mounting the projector on a
ceiling.
Ceiling mount screws:
M4 x 5 (Max. L = 12 mm)
Unit: mm
Bottom view
Note:
When installing, ensure that you use only UL Listed ceiling mounts.
For ceiling installations, use approved mounting hardware and M4 screws with a maximum screw
depth of 12 mm (0.47 inch).
The construction of the ceiling mount must be of a suitable shape and strength. The ceiling mount
load capacity must exceed the weight of the installed equipment, and as an additional precaution
be capable of withstanding three times the weight of the equipment over a period of 60 seconds.
7
！
Remote Control Parts
Important:
1. Avoid using the projector with bright fluorescent lighting turned on. Certain high-frequency
fluorescent lights can disrupt remote control operation.
2. Be sure nothing obstructs the path between the remote control and the projector. If the path
between the remote control and the projector is obstructed, you can bounce the signal off certain
reflective surfaces such as projector screens.
3. The buttons and keys on the projector have the same functions as the corresponding buttons on
the remote control. This user’s manual describes the functions based on the remote control.
Note:
Complies with FDA performance standards for laser products except for deviations pursuant to
Laser Notice No. 50, dated June 24, 2007
Caution:
Use of controls, adjustments or performance of procedures other than those specified herein
may result in hazardous laser light exposure.
8
ITEM
LABEL
DESCRIPTION
SEE PAGE
1.
IR Transmitter
Transmits signals to projector.
2.
Power On
Turns the projector on.
12
3.
HDMI
Displays the HDMI 2 source.
4.
COMP
Displays the VGA1/VGA2 source selection (toggle).
5.
Video
Displays the VIDEO/S-VIDEO source selection.
6.
Navigates and changes settings in the OSD.
Quick Menu – For Vertical Keystone.
23
7.
Auto SYNC
Auto adjustment for frequency, phase, and position.
8.
Navigates and changes settings in the OSD.
Quick Menu – For Horizontal Keystone.
23
9.
MENU
Opens the OSD.
23
10.
Navigates and changes settings in the OSD.
Quick Menu – For Vertical Keystone.
23
11.
Laser
Press to operate the on-screen pointer. DO NOT POINT IN EYES.
12.
Performs the same function as the left mouse button when the mouse
mode is activated.
13.
MOUSE
Switches between the normal and mouse modes.
PgUp, PgDn, , , ▲, ▼, ◄, ►, : active after pressing
Mouse. An icon appears on the screen to indicate the activation of the
mouse mode.
Note: Only available when a PC input signal is selected.
14.
ID SET
Sets remote control code
15.
PgUp / 1
Perform page up function when mouse mode is activated.
Number for Remote ID setting used.
16.
Blank / 3
Makes the screen blank.
Number for Remote ID setting used.
17.
/ 4
Mutes the built-in speaker.
Number for Remote ID setting used.
22
18.
/ 6
Selects the display aspect ratio.
19.
Displays the presentation timer settings menu.
20.
ECO MODE
Selects a lamp mode.
21.
Activates panel key lock.
22.
Laser
Use as on-screen pointer. DO NOT POINT IN EYES.
23.
Allows user to define a short cut key on the remote
control, and the function item is selected in OSD menu.
23
24.
HDMI / MHL
Displays the HDMI1 source.
Enable the Mobile High-Definition Link technology feature for smart
devices.
25.
Source
Alternate input source.
23
26.
BNC
Displays the BNC source.
27.
Freeze
Freezes/unfreezes the on-screen picture.
9
ITEM
LABEL
DESCRIPTION
SEE PAGE
28.
Enters and confirms settings in the OSD.
Displays the Corner Adj. page.
23
29.
Navigates and changes settings in the OSD.
Quick Menu – For Horizontal Keystone.
23
30.
EXIT
Return to last OSD page.
23
31.
Performs the same function as the right mouse button when the mouse
mode is activated.
32.
PgDn / 2
Perform page down function when mouse mode is activated.
Number for Remote ID setting used.
33.
PATTERN / 5
Displays embedded test pattern.
Number for Remote ID setting used.
34.
/ 7
Increase the volume level..
Number for Remote ID setting used.
22
35.
/ 8
Displays the HELP menu.
Number for Remote ID setting used.
36.
Decreases the volume level.
22
37.
Displays the digital zoom settings bar.
21
38.
COLOR MODE
Selects an available picture setup mode.
39.
Wired Jack
Connect wire remote to the projector.
Remote control code
The projector can be assigned to 8 different remote control codes, 1 to 8. When several adjacent
projectors are in operation at the same time, switching the remote control codes can prevent interference
from other remote controls. Set the remote control code for the projector first before changing that for the
remote control.
To switch the code for the projector, select from among 1 to 8 in the Basic > Advanced > Remote Control
Code menu.
To switch the code for the remote control, press ID set and the corresponding button from 1 to 8 buttons
on the remote control together for 5 seconds or more. The initial code is set to1. When the code is
switched to 8, the remote control can control every projector.
Note:
If different codes are set on the projector and remote control, there will be no response from the
remote control. When that happens, switch the code for the remote control again.
10
Using the remote mouse control
The capability of operating your computer with the remote control gives you more flexibility when delivering
presentations.
1. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in
place of your computer’s mouse.
2. Set the input signal to COMPUTER.
3. Press Mouse on the remote control to switch from the normal mode to the mouse mode. An icon
appears on the screen to indicate the activation of the mouse mode.
4. Perform the desired mouse controls on your remote control.
To move the cursor on the screen, press ▲ / ▼ / ◄ / ►/ .
To left-click, press .
To right-click, press .
To operate your display software program (on a connected PC) which responds to page up/down
commands (like Microsoft PowerPoint), press Page Up/Page Down.
To return to the normal mode, press Mouse again or other keys except for the mouse related
multi-function keys.
Remote Control Operating Range
The remote control uses infrared transmission to control the projector. It is not necessary to point the
remote directly at the projector. Provided you are not holding the remote perpendicular to the sides or the
rear of the projector, the remote will function well within a radius of about 7 meters (23 feet) and 15
degrees above or below the projector level. If the projector does not respond to the remote control, move a
little closer.
Projector and Remote Control Buttons
The projector can be operated using the remote control or the buttons on the top of the projector. All
operations can be carried out with the remote control; however, the buttons on the projector are limited in
use.
11
1.
Remove the battery compartment
cover by sliding the cover in the
direction of the arrow.
2.
Insert the battery with the positive
side facing up.
3.
Replace the cover.
Inserting the Remote Control Batteries
SETUP AND OPERATION
Caution:
1. Only use AAA batteries (Alkaline batteries are recommended).
2. Dispose of used batteries according to local ordinance regulations.
3. Remove the batteries when not using the projector for prolonged periods.
12
1.
Securely connect the power cord and
signal cable. When connected, the power
led will flash green to solid green.
2.
Turn on the lamp by pressing “ ” button
on the top of the projector or “ ” on the
remote control.
The PWR LED will now flash green.
The startup screen will display in
approximately 30 seconds. The first time
you use the projector, you can select
your preferred language from quick menu
after the startup screen display. (See
Setting the OSD Language on page 24)
See Setting an Access Password
(Security Lock) on page 14 if security lock
is enabled.
Starting and Shutting down the Projector
13
3.
If more than one input device is
connected, press the SOURCE button
and use ▲▼ to scroll among devices.
(Component is supported through the
RGB to Component adapter.)
HDMI 1 / MHL: High-Definition Multimedia Interface
and Mobile High-Definition Link
compatible
HDMI 2: High-Definition Multimedia Interface
compatible
DVI: DVI
VGA 1 / 2: Analog RGB
DVD input YCbCr/ YPbPr, or HDTV input
YPbPr via D-sub connector
BNC: Analog RGB
S-Video: Super video (Y/C separated)
Composite Video: Traditional composite video
4.
When the “Power Off? /Press Power
again” message appears, press the
POWER button. The projector turns off.
Caution:
Do not unplug the power cord until the POWER LED stops flashing – indicating the projector has
cooled down.
14
1.
Press the MENU button to open the
OSD menu.
2.
Press the cursor ◄► button to move
to the Basic menu.
3.
Press the cursor ▲▼ button to select
Advanced.
Setting an Access Password (Security Lock)
You can use the four (arrow) buttons to set a password and prevent unauthorized use of the projector.
When enabled, the password must be entered after you power on the projector. (See Navigating the OSD
on page 23 and Setting the OSD Language on page 24 for help on using OSD menus.)
Important:
Keep the password in a safe place. Without the password, you will not be able to use the projector.
If you lose the password, contact your reseller for information on clearing the password.
15
4.
Press the cursor ▲▼ button to select
Security Lock.
5.
Press the cursor ◄► button to enable
or disable security lock function.
A password dialog box automatically
appears.
6.
You can use the cursor buttons
▲▼◄►
on IR remote control for password
entry. You can use any combination
including the same arrow five times,
but not less than five.
Press the cursor buttons in any order
to set the password. Push the MENU
button to exit the dialog box.
7.
The password confirm menu appears
when user presses the power-on key
in case the Security Lock is enabled.
Enter the password in the order you
set it at step 6. In case you forget the
password, please contact the service
center.
Service center will validate the owner
and help reset the password.
16
1.
To raise the level of the projector, twist
the adjusters counter clockwise.
2.
To lower the level of the projector, lift the
projector and twist the adjusters
clockwise.
Adjusting the Projector Level
Take note of the following when setting up the projector:
The projector table or stand should be level and sturdy.
Position the projector so that it is perpendicular to the screen.
Ensure the cables are in a safe location. You could trip over them.
17
ZOOM
FOCUS
LENS SHIFT
SOURCE
MENU
EXIT
ENTER
Adjusting Projected Image Position Using Lens Shift
The Lens Shift feature provides a lens shift function that can be used to adjust the position of the projected
image either horizontally or vertically within the range detailed below.
Note:
Do not rotate lens shift knob further under click sound and lightly press the knob to rotate back.
Loading...