ViewSonic PJ658 User Manual

ViewSonic

PJ658D

DLP Projector

- User Guide

使用手冊 (繁體)

使用手冊(简体)

Model No. : VS11454

ViewSonic PJ658Di

Compliance Information

For U.S.A.

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Warning: You are cautioned that changes or modications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

For Canada

• This Class B digital apparatus complies with Canadian ICES-003.

• Cet appareil numérique de la classe B est conforme

à la norme NMB-003 du

Canada.

CE Conformity for European Countries

The device complies with the requirements of the EEC directive 89/336/ EEC as amended by 92/31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic compatibility”, and 73/23/EEC as amended by 93/68/EEC Art.13 with regard to “Safety.”

Following information is only for EU-member states:

The mark shown to the right is in compliance with the Waste Electrical and Electronic Equipment Directive 2002/96/EC (WEEE).

The mark indicates the requirement NOT to dispose the equipment as unsorted municipal waste, but use the return and collecti on systems according to local law.

iiViewSonic PJ658D

Important Safety Instructions

1. Read these instructions completely before using the equipment.

2. Keep these instructions in a safe place.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this equipment near water. Warning: To reduce the risk of fire or electric

shock, do not expose this apparatus to rain or moisture.

6. Clean with a soft, dry cloth. If further cleaning is required, see “Cleaning the Display” in this guide for further instructions.

7. Do not block any ventilation openings. Install the equipment in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other

devices (including ampliers) that produce heat.

9. Do not attempt to circumvent the safety provisions of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade and the third prong are

provided for your safety. If the plug does not t into your outlet, consult an electrician for

replacement of the outlet.

10. Protect the power cord from being tread upon or pinched, particularly at the plug, and the point where if emerges from the equipment. Be sure that the power outlet is located near the equipment so that it is easily accessible.

11. Only use attachments/accessories specied by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the

manufacturer, or sold with the equipment. When a cart is used, use caution when moving the cart/equipment combination to avoid injury from tipping over.

13. Unplug this equipment when it will be unused for long periods of time.

14. Refer all servicing to qualied service personnel. Service is required when the unit has

been damaged in any way, such as: if the power-supply cord or plug is damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed to rain or moisture, or if the unit does not operate normally or has been dropped.

ViewSonic PJ658Diii

Declaration of RoHS Compliance

This product has been designed and manufactured in compliance with Directive 2002/95/EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Proposed Maximum

Concentration

Actual Concentration

Lead (Pb)

0.1% < 0.1%

Mercury (Hg)

0.1% < 0.1%

Cadmium (Cd)

0.01% < 0.01%

Hexavalent Chromium (Cr

) 0.1% < 0.1%

Polybrominated biphenyls (PBB)

0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE)

0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex of the RoHS Directives as noted below:

Examples of exempted components are:

1. Mercury in compact fluorescent lamps not exceeding 5 mg per lamp and in other

lamps not specically mentioned in the Annex of RoHS Directive.

2. Lead in glass of cathode ray tubes, electronic components, fluorescent tubes, and

electronic ceramic parts (e.g. piezoelectronic devices).

3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by

weight or more lead).

4. Lead as an allotting element in steel containing up to 0.35% lead by weight,

aluminium containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.

Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.

Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.

ViewSonic, the th ree birds’ logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation.

VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA.

PS/2, VGA and XGA are registered trad em ar ks of Internation al B us iness Machines Corporation.

Disclaimer:ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

Product Registration

To meet your future needs, and to receive any additional product information as it becomes available, please register your product on the Internet at: www.viewsonic.com. The ViewSonic Wizard CD-ROM also provides an opportunity for you to print the registration form, which you may mail or fax to ViewSonic.

For Your Records

Product Name:

Model Number: Document Number: Serial Number: Purchase Date:

The lamp in this product contains mercury.

Please dispose of in accordance with local, state or federal laws.

PJ658D ViewSonic DLP Projector VS11454 PJ658D-1_UG_ENG Rev. 1C 02-27-07

ivViewSonic PJ658D

ViewSonic PJ658D1

Safety Instructions

Read all of these instructions before you operate your projector and save for future reference.

1. Check that the operating voltage of your unit is identical with the voltage of your

local power supply.

2. Should any liquid or solid object fall into the cabinet, unplug the unit and have it

checked by the qualied personnel before operating it further.

3. Do not attempt to service this product yourself, as opening or removing covers may

damage the components inside and will void your warranty.

4. Do not place this product on an unstable cart, stand, or table. The product may

fall, causing serious damage to the product.

5. Unplug the unit from the wall socket if it is not to be used for several days. To

disconnect the cord, pull it out by the plug. Never pull the cord itself.

6. The wall socket should be near the unit and easily accessible.

7. Do not place the projector where the cord can be stepped on as this may result in

fraying or damage to the lead or the plug. Be alert to tripping hazards.

8. Never look into the projector lens when the lamp is switched on as the bright light

can damage your eyes. Never let children look into the lens when it is on.

9. Do not place your hand or objects near the ventilation holes. The air coming out is

hot.

10. Never open any covers on the projector except the lamp cover. Dangerous electrical

voltages inside the projector can cause severe injury. Except as specically directed

in this User’s Manual, do not attempt to service this product yourself. Refer all

servicing to qualied service personnel.

11. Unplug the projector from the wall socket before cleaning. Use a damp cloth for

cleaning the projector housing. Do not use liquid or aerosol cleaners.

12. Keep the plastic packing materials (from the projector, accessories and optional

parts) out of the reach of children as these bags may result in death by suffocation. Be particularly careful around the small children.

2ViewSonic PJ658D

13. For ventilation reasons, the fan continues to operate after the projector has been

powered off. Please do not unplug the power cord until the fan stops.

14. The projector is equipped with ventilation holes (intake) and ventilation holes

(exhaust). Do not block or place anything near these slots, or internal heat build-up may occur, causing picture degradation or damage to the projector.

15. When you replace the projector lamp, never touch the new bulb with your bare

hands. The invisible residue left by the oil on your hands may shorten the bulb life.

Use lint-free gloves or nger cots are recommended.

16. The product should be situated away from heat sources such as radiators, heat

registers, stoves, or other products (including ampliers) that produce heat.

17. Do not overload wall outlets, extension cords, or integral convenience receptacles

as this can result in a risk of re or electric shock.

ViewSonic PJ658D3

Ground

Notes on AC Power Cord

AC Power Cord must meet requirement of country where you use a projector. Conrm

an AC plug type with graphics below and proper AC Power Cord must be used. If supplied AC Power Cord does not match your AC outlet, contact your sales dealer. This projector is equipped with a grounding type AC line plug. Make sure that your outlet

ts the plug. Do not defeat the safety purpose of this grounding type plug. We highly

recommend using a video source device also equipped with a grounding type AC line

plug to prevent from signal interference due to voltage uctuation.

4ViewSonic PJ658D

CONTENTS

Introduction ..............................................................................................................5

Projector Features ............................................................................................

Package Contents .............................................................................................

Projector Overview ............................................................................................

Using the Product .....................................................................................................

Control Panel

.....................................................................................................9

Connection Ports .............................................................................................

Remote Control ...............................................................................................

Installing the Batteries .....................................................................................

Remote Control Operation ..............................................................................

Installation ..............................................................................................................

Connecting the Projector .................................................................................

Powering On/Off the Projector ........................................................................

Adjusting the Projected Image ........................................................................

Adjusting the Projector Zoom and Focus ........................................................

Adjusting Projection Image Size

......................................................................18

Menu Operation ......................................................................................................

All Images (Computer / Video Mode) .............................................................

Computer Image (Computer Mode) ................................................................

Video Image (Video Mode) ..............................................................................

Audio (Computer / Video Mode) ......................................................................

Management (Computer / Video Mode) ..........................................................

Language (Computer / Video Mode) ...............................................................

Factory Reset (Computer / Video Mode) .........................................................

Maintenance ...........................................................................................................

Cleaning the Lens ...........................................................................................

Cleaning the Projector Housing

.......................................................................27

Replacing the Lamp ........................................................................................

Technical Specications .........................................................................................30

Appendix

.................................................................................................................31

Indicator Messages .........................................................................................

Compatibility Modes ........................................................................................

Troubleshooting ...............................................................................................

ViewSonic PJ658D5

Introduction

Projector Features

The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use.

The projector offers the following features:

Single chip Texas Instruments DLP™ technology

XGA (1024 x 768 pixels)

Compact size, light weight for portability

1.2x manual zoom lens

Auto image re-sizing (Auto-Sync.) to 1024 x 768 full screen with scaling compression

compatibility for VGA, SVGA, XGA and SXGA*.

State-of-the-art motion adaptive hardware deinterlacing with 3:2 pull down

Compatibility with Macintosh® computers

Compatibility with NTSC, PAL, SECAM, and HDTV

Multi-function remote control

D-Sub 15-pin cable for analog video connectivity

User-friendly, multi-language on-screen display (OSD)

Advanced electronic keystone correction

* means compressed.

6ViewSonic PJ658D

Package Contents

When you unpack the projector, make sure you have all these components:

Projector with Lens Cap AC Power Cord VGA Cable (D-SUB to D-SUB)

Composite Video Cable

VGA (D-SUB) to HDTV (RCA) Cable

User’s Manual

Remote Control (IR)

Optional Accessory:

POWER

MUTE

4:3/16:9 KEYSTONE

LASER

ENTER BLANK

VOLUME

AUTO SOURCE

Quick Start Guide

AAA size batteries for remote control

Save the original shipping carton and packing material; they will come in handy

if you ever to ship your unit. For maximum protection, repack your unit as it

was originally packed at the factory.

Accessories and components may vary by retailer and region.

Audio Cable

USB CableRS232 Cable

Projector Carrying Case

S-Video Cable

ViewSonic PJ658D7

Projector Overview

Front View

1 Elevator foot

2 Elevator button

3 Lens cap

4 Lens cap strap

5 Front IR remote control

sensor

1 2 3 6 7

10 11

6 Lens

7 Focus ring

8 Ventilation holes

Speaker

Control panel

Zoom ring

8ViewSonic PJ658D

1 2

3 34 5 7

This projector can be used with a ceiling mount for support. The ceiling mount

is not included in the package.

Rear View

1 Rear IR remote control sensor 2 Connection ports 3 Tilt-adjustment foot 4 Kensington lock 5 Ventilation holes

6 Main power switch 7 AC power socket

Bottom View

1 Lamp cover

2 Ceiling mount

+ 30 hidden pages