IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specic languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”
Model No. VS16964/VS16963
Compliance Information
FCC Statement
This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and
if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:
yReorient or relocate the receiving antenna.yIncrease the separation between the equipment and receiver.yConnect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
yConsult the dealer or an experienced radio/TV technician for help.
Warning: You are cautioned that changes or modications not expressly approved
by the party responsible for compliance could void your authority to operate the
equipment.
For Canada
CAN ICES-3 (B)/NMB-3(B)
CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU and Low Voltage
Directive 2014/35/EU.
Following information is only for EU-member states:
The mark is in compliance with the Waste Electrical and Electronic
Equipment Directive 2012/19/EU (WEEE).
The mark indicates the requirement NOT to dispose the equipment
including any spent or discarded batteries or accumulators as unsorted
municipal waste, but use the return and collection systems available.
If the batteries, accumulators and button cells included with this equipment,
display the chemical symbol Hg, Cd, or Pb, then it means that the battery
has a heavy metal content of more than 0.0005% Mercury or more than,
0.002% Cadmium, or more than 0.004% Lead.
i
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this unit near water.
6. Clean with a soft, dry cloth.
7. Do not block any ventilation openings. Install the unit in accordance with the
manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves,
or other devices (including ampliers) that produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A
polarized plug has two blades with one wider than the other. A grounding type
plug has two blades and a third grounding prong. The wide blade and the third
prong are provided for your safety. If the provided plug does not t into your
outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched particularly at plugs.
Convenience receptacles and the point where they exit from the unit. Be sure
that the power outlet is located near the unit so that it is easily accessible.
11. Only use attachments/accessories specied by the manufacturer.
12. Use only with the cart, stand, tripod, bracket, or table specied by
the manufacturer, or sold with the unit. When a cart is used, use
caution when moving the cart/unit combination to avoid injury from
tipping over.
13. Unplug this unit when unused for long periods of time.
14. Refer all servicing to qualied service personnel. Servicing is required when the
unit has been damaged in any way, such as: if the power-supply cord or plug is
damaged, if liquid is spilled onto or objects fall into the unit, if the unit is exposed
to rain or moisture, or if the unit does not operate normally or has been dropped.
ii
Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive
2011/65/EU of the European Parliament and the Council on restriction of the use
of certain hazardous substances in electrical and electronic equipment (RoHS2
Directive) and is deemed to comply with the maximum concentration values issued
by the European Technical Adaptation Committee (TAC) as shown below:
Certain components of products as stated above are exempted under the Annex III
of the RoHS2 Directives as noted below:
Examples of exempted components are:
1. Mercury in cold cathode uorescent lamps and external electrode uorescent
lamps (CCFL and EEFL) for special purposes not exceeding (per lamp):
(1) Short length (≦500 mm): maximum 3.5 mg per lamp.
(2) Medium length (>500 mm and ≦1,500 mm): maximum 5 mg per lamp.
(3) Long length (>1,500 mm): maximum 13 mg per lamp.
2. Lead in glass of cathode ray tubes.
3. Lead in glass of uorescent tubes not exceeding 0.2% by weight.
4. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.
5. Copper alloy containing up to 4% lead by weight.
6. Lead in high melting temperature type solders (i.e. lead-based alloys containing
85% by weight or more lead).
7. Electrical and electronic components containing lead in a glass or ceramic other
than dielectric ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or
ceramic matrix compound.
for any purpose without prior written permission from ViewSonic Corporation.
Product Registration
To fulfill possible future product needs, and to receive additional product information
as it becomes available, please visit your region section on ViewSonic’s website to
register your product online.
Registering your product will best prepare you for future customer service needs.
Please print this user guide and fill the information in the “For Your Records” section.
For additional information, please see the “Customer Support” section in this guide.
For Your Records
Product Name:PX705HD/PA505W
ViewSonic DLP Projector
Model Number:VS16964/VS16963
Document Number:PX705HD/PA505W_UG_ENG Rev. 1A 10-18-17
Serial Number:________________________________________
Purchase Date:________________________________________
Product disposal at end of product life
The lamp in this product contains mercury which can be dangerous to you and the
environment. Please use care and dispose of in accordance with local, state or
federal laws.
ViewSonic respects the environment and is committed to working and living green.
Thank you for being part of Smarter, Greener Computing. Please visit ViewSonic
website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx
iv
Table of contents
Important safety
instructions .......................2
Introduction......................4
Projector features .................................4
IR control table .................................. 58
RS232 command table....................... 59
1
Important safety instructions
Your projector is designed and tested to meet the latest standards for safety of information
technology equipment. However, to ensure safe use of this product, it is important that you
follow the instructions mentioned in this manual and marked on the product.
Safety Instructions
1.Please read this manual before you operate your projector. Save it for future
reference.
2.Do not look straight at the projector lens during operation. The intense light beam
may damage your eyes.
3.Refer servicing to qualified service personnel.
4.Always open the lens shutter or remove the lens cap when the projector lamp is
on.
5.In some countries, the line voltage is NOT stable. This projector is designed to operate
safely within a mains voltage between 100 to 240 volts AC, but could fail if power
cuts or surges of ±10 volts occur. In areas where the mains voltage may fluctuate
or cut out, it is recommended that you connect your projector through a power
stabilizer, surge protector or uninterruptible power supply (UPS).
6.Do not block the projection lens with any objects when the projector is under
operation as this could cause the objects to become heated and deformed or even
cause a fire. To temporarily turn off the lamp, press BLANK on the projector or
remote control.
7.The lamp becomes extremely hot during operation. Allow the projector to cool for
approximately 45 minutes prior to removing the lamp assembly for replacement.
8.Do not operate lamps beyond the rated lamp life. Excessive operation of lamps
beyond the rated life could cause them to break on rare occasions.
9.Never replace the lamp assembly or any electronic components unless the projector is
unplugged.
10. Do not place this product on an unstable cart, stand, or table. The product may fall,
sustaining serious damage.
11. Do not attempt to disassemble this projector. There are dangerous high voltages inside
which may cause death if you should come into contact with live parts. The only user
serviceable part is the lamp which has its own removable cover.
Under no circumstances should you ever undo or remove any other covers. Refer
servicing only to suitably qualified professional service personnel.
12. Do not place this projector in any of the following environments.
- Space that is poorly ventilated or confined. Allow at least 50 cm clearance from walls
and free flow of air around the projector.
- Locations where temperatures may become excessively high, such as the inside of a
car with all windows rolled up.
- Locations where excessive humidity, dust, or cigarette smoke may contaminate optical
components, shortening the projector's life span and darkening the picture.
- Locations near fire alarms
- Locations with an ambient temperature above 40°C / 104°F
- Locations where the altitudes are higher than 3000 m (10000 feet).
2
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed,
overheating inside the projector may result in a fire.
- Do not place this projector on a blanket, bedding or any other soft surface.
- Do not cover this projector with a cloth or any other item.
- Do not place inflammables near the projector.
14. Always place the projector on a level, horizontal surface during operation.
- Do not use if tilted at an angle of more than 10 degrees left to right, nor at angle of
more than 15 degrees front to back. Using the projector when it is not fully horizontal
may cause a malfunction of, or damage to, the lamp.
15. Do not stand the projector on end vertically. Doing so may cause the projector to fall
over, causing injury or resulting in damage to the projector.
16. Do not step on the projector or place any objects upon it. Besides probable physical
damage to the projector, doing so may result in accidents and possible injury.
17. Do not place liquids near or on the projector. Liquids spilled into the projector may
cause it to fail. If the projector does become wet, disconnect it from the power
supply's wall socket and call your local service center to have the projector serviced.
18. This product is capable of displaying inverted pictures for ceiling mount installation.
Use only qualified ceiling mount kit for mounting the projector and ensure it is
securely installed.
19. When the projector is under operation, you may sense some heated air and odor from
its ventilation grill. It is a normal phenomenon and not a product defect.
20. Do not use the Security bar for transporting or installation. It should be used with a
commercially available theft prevention cable.
Safety instructions for ceiling mounting of the
projector
We want you to have a pleasant experience using your projector, so we need to bring this
safety matter to your attention to prevent damage to person and property.
If you intend to mount your projector on the ceiling, we strongly recommend that you use a
proper fitting projector ceiling mount kit and that you ensure it is securely and safely
installed.
If you use an inappropriate projector ceiling mount kit, there is a safety risk that the
projector may fall from the ceiling due to an improper attachment through the use of the
wrong gauge or length screws.
You can purchase a projector ceiling mount kit from the place you purchased your projector.
We recommend that you also purchase a separate security cable and attach it securely to
both the anti-theft lock slot on the projector and the base of the ceiling mount bracket. This
will perform the secondary role of restraining the projector should its attachment to the
mounting bracket become loose.
As with any bright light source, do not stare into the beam, RG2
IEC 62471-5:2015.
3
Introduction
Projector features
The projector integrates high-performance optical engine projection and a user-friendly
design to deliver high reliability and ease of use.
The projector offers the following features.
• Dynamic mode adjusting the power consumption of the lamp according to the
brightness of the image being projected
• Power saving function decreasing the power consumption of the lamp by up to 70%
when no input signal can be detected for a set period of time.
• Presentation timer for better control of time during presentations
• Supports 3D display
•ColorManagement allowing color adjustments to your liking
• Less than 0.5W power consumption when power saving mode is turned on
• Screen Color correction allowing projection on surfaces of several predefined colors
• Quick auto search speeding up the signal detecting process
• Color modes providing choices for different projection purposes
• Selectable quick power off function
• One-key auto-adjustment to display the best picture quality
• Digital keystone correction to correct distorted images
• Adjustable color management control for data/video display
• Ability to display 1.07 billion colors
• Multi-language On-Screen Display (OSD) menus
• Switchable normal and economic modes to reduce the power consumption
• Component HDTV compatibility (YP
• HDMI CEC (Consumer Electronics Control) function allows synchronized power ON/
OFF operation between the projector and a CEC-compatible DVD player device
connected to the HDMI input of the projector
The apparent brightness of the projected image will vary depending on the ambient lighting
conditions, selected input signal contrast/brightness settings, and is directly proportional to
projection distance.
The lamp brightness will decline over time and may vary within the lamp manufacturers
specifications. This is normal and expected behavior.
bPr)
4
Shipping contents
Home Projector
Quick Start Guide
ViewSonic Corporation (US/Canada/Latin America)
: www.viewsonic.com/support/product-registration
: 14035 Pipeline Ave. Chino, CA 91710, USA
: 909-468-1240
ViewSonic Europe Ltd.
: www.viewsoniceurope.com
: 1st Floor, Salamanca Place,9 Albert Embankment, London
SE1 7SP, United Kingdom
: +44 (0) 207 382 8251
Carefully unpack and verify that you have all of the items shown below. If any of these
items are missing, please contact your place of purchase.
Standard accessories
The supplied accessories will be suitable for your region, and may differ from those
illustrated.
ProjectorPower CordVGA Cable
Quick Start Guide
Optional accessories
1.Replacement lamp
Remote Control &
Batteries
5
Projector exterior view
1234 5 6 78
Front/upper
9
1917 18161520 21
10 11
131214
22
Rear/lower side
1.Lamp cover
2.Front IR remote sensor
3.Projection lens
4.Focus ring
5.Zoom ring
6.Power button and LED indicators
7.External control panel
(See "Projector" on page 7 for
details.)
8.Vent (air inlet)
9.AC power cord inlet
10. HDMI-1 port
11. HDMI-2 port
12. RGB (PC)//Component video
(YPbPr/YCbCr) signal input
socket-2
13. RGB (PC)//Component video
(YPbPr/YCbCr) signal input
socket-1
14. RS232 control port
15. Monitor out socket
16. Video input socket
17. Audio signal output socket
18. Audio signal input socket
19. USB port (5V/1.5A out)
20. Mini USB port
21. Kensington Security Slot
22. Adjuster foot
Warni ng
•THIS APPARATUS MUST BE EARTHED.
•When installing the unit, incorporate a readily accessible disconnect device in the fixed wiring,
or connect the power plug to an easily accessible socket-outlet near the unit. If a fault should
occur during operation of the unit, operate the disconnect device to switch the power supply
off, or disconnect the power plug.
6
Controls and functions
Projector
21
1.Focus ring
Adjusts the focus of the projected image.
2.Zoom ring
Adjusts the size of the projected image.
3.Power
Toggles the projector between standby
mode and Power ON.
4. (Power indicator light)
Lights up or flashes when the projector is
under operation.
5. (Temperature indicator light)
Lights up red if the projector's temperature
becomes too high.
6. (Lamp indicator light)
Indicates the status of the lamp. Lights up
or flashes when the lamp has developed a
problem.
7. (Menu up)
Selects the desired menu items and makes
adjustments.
(Keystone key)
Manually corrects distorted images
resulting from an angled projection.
8.Blank
Makes the screen blank.
9.Menu
Turns on the On-Screen Display (OSD)
menu.
223 4 5 6 78
10 11 12 13 14 159
Exit
Goes back to previous OSD menu, exits
and saves menu settings.
10. Source
Displays the source selection bar.
(Help)
Displays the HELP menu by a long press
for 3 seconds.
11. (Volume down)
Decrease the volume level.
(Left)
Selects the desired menu items and makes
adjustments.
12. (Menu down)
Selects the desired menu items and makes
adjustments.
(Keystone key)
Manually corrects distorted images
resulting from an angled projection.
13. Enter
Enacts the selected On-Screen Display
(OSD) menu item.
14. Color Mode
Selects an available picture setup mode.
15. (Volume up)
Increase the volume level.
(Right)
Selects the desired menu items and makes
adjustments.
7
17
21
22
23
24
25
26
18
19
20
16
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Remote control
1.Power
Toggles the projector between standby
mode and Power ON.
2.VIDEO
Selects Video source for display.
3.COMP
Selects D-Sub / Comp. source for
display.
4.Auto Sync
Automatically determines the best
picture timings for the displayed
image.
5./ (Keystone keys)
Manually corrects distorted images
resulting from an angled projection.
Left/Right/Up/ Down
Selects the desired menu items and
makes adjustments.
6. (Information)
Displays the Information menu.
7.Menu
Turns on the On-Screen Display
(OSD) menu.
8.Freeze
Freezes the projected image.
9.Aspect
Selects the display aspect ratio.
8
10. PgUp (Page Up)/
HDMI
/MHL
Operates your display software program
(on a connected PC) which responds to
page up commands (like Microsoft
PowerPoint) when the mouse mode is
activated.
11. (Volume up)
Increase the volume level.
12. PgDn (Page Down)
Operates your display software program
(on a connected PC) which responds to
page down commands (like Microsoft
PowerPoint).
Only available when a PC input signal is
selected.
17. Power Off
Turns the projector off.
18. HDMI
Selects HDMI source for display.
19. Source
Displays the source selection bar.
20. Enter
Enacts the selected On-Screen Display
(OSD) menu item.
21. Exit
Goes back to previous OSD menu, exits
and saves menu settings.
22. Pattern
Displays embedded test pattern.
23. Blank
13. (Volume down)
Decrease the volume level.
14. Eco Mode
Selects a lamp mode.
15. (Mute)
Toggles the projector audio between on and
off.
16. LED indicator
Hides the screen picture.
24. (Zoom in)
Magnifies the projected picture size.
25. (Zoom out)
Reduces the projected picture size.
26. Color Mode
Selects an available picture setup mode.
Remote control code
The projector can be assigned to 8 different remote control
codes, 1 to 8. When several adjacent projectors are in
operation at the same time, switching the remote control codes
can prevent interference from other remote controls. Set the
remote control code for the projector first before changing that
for the remote control.
To switch the code for the projector, select from among 1 to 8
in the SYSTEM SETTING: ADVANCED > Remote Control Code menu.
To switch the code for the remote control,
press ID set and the number button
corresponding to the remote control code
set in the projector OSD together for 5
seconds or more. The initial code is set to
1. When the code is switched to 8, the
remote control can control every
projector.
If different codes are set on the projector and remote control, there will be no response from
the remote control. When that happens, a message will display to remind you to switch the
code for the remote control.
9
Using the remote PgUp/PgDn function
Approx. 30°
A
pp
r
ox
.
30
°
The capability of operating your computer with the remote control gives you more
flexibility when delivering presentations.
1.Set the input signal to a PC signal.
2.Connect the projector to your PC or notebook with a USB cable prior to using the
remote control in place of your computer’s mouse. See "Connecting a computer or a
monitor" on page 18 for details.
3.To operate your display software program (on a connected PC) which responds to
page up/down commands (like Microsoft PowerPoint), press PgUp/PgDn.
Remote control effective range
The Infra-Red (IR) remote control is located on the
front of the projector. The remote control must be held
at an angle within 30 degrees perpendicular to the
projector's IR remote control sensor to function
correctly. The distance between the remote control and
the sensor should not exceed 8 meters (~ 26 feet).
Make sure that there are no obstacles between the
remote control and the IR sensor on the projector that
might obstruct the infra-red beam.
10
Replacing the remote control batteries
1.To open the battery cover, turn the remote control over to view its back, press on the
finger grip on the cover and pull it up in the direction of the arrow as illustrated.
2.Remove any existing batteries (if necessary) and install two AAA batteries observing
the battery polarities as indicated in the base of the battery compartment. Positive (+)
goes to positive and negative (-) goes to negative.
3.Refit the cover by aligning it with the base and pushing it back down into position.
Stop when it clicks into place.
WARNING
• Avoid leaving the remote control and batteries in an excessive heat or humid environment
like the kitchen, bathroom, sauna, sunroom or in a closed car.
• Replace only with the same or equivalent type recommended by the battery manufacturer.
• Dispose of the used batteries according to the manufacturer's instructions and local
environment regulations for your region.
• Never throw the batteries into a fire. There may be danger of an explosion.
• If the batteries are drained or if you will not be using the remote control for an extended
period of time, remove the batteries to avoid damage to the remote control from possible
battery leakage.
• RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.
• DISPOSE OF USED BATTERIES ACCORDING TO THE INSTRUCTIONS.
11
Positioning your projector
Choosing a location
Your room layout or personal preference will dictate which installation location you select.
Take into consideration the size and position of your screen, the location of a suitable power
outlet, as well as the location and distance between the projector and the rest of your
equipment.
Your projector is designed to be installed in one of the following 4 possible installation
locations:
1.Front Table
Select this location with the projector placed near
the floor in front of the screen. This is the most
common way to position the projector for quick
setup and portability.
2.Front Ceiling
Select this location with the projector suspended
upside-down from the ceiling in front of the screen.
Purchase the projector ceiling mount kit from your
dealer to mount your projector on the ceiling.
Set Front Ceiling in the SYSTEM > Projector
Position menu after you turn the projector on.
3.Rear Ceiling
Select this location with the projector suspended
upside-down from the ceiling behind the screen.
Note that a special rear projection screen and the
projector ceiling mounting kit are required for this
installation location.
Set Rear Ceiling in the SYSTEM > Projector
Position menu after you turn the projector on.
4.Rear Table
Select this location with the projector placed near
the floor behind the screen.
Note that a special rear projection screen is
required.
Set Rear Table in the SYSTEM > Projector Position menu after you turn the projector on.
12
Projection dimensions
(f): Center of lens(e): Screen
• 16:9 image on a 16:9 screen
• 16:9 image on a 4:3 screen
PX705HD
The "screen" mentioned below refers to the projection screen usually consisting of a screen
surface and a support structure.
(a) Screen Size
inchmminchmminchmminchmminch mm inch mm
501270651651721829256352.2553.793
601524781981862184297372.6664.4112
7017789223371012565348643775.2131
80203210526671152921399913.5885.9149
902286118299712932774411183.9996.6168
1002540131332714436584912454.3110 7.4187
1102794144365815840135413724.8 1218.1205
1203048157398817343945914995.2 1318.8224
1303302170431818747506416265.6 1429.6243
1403556183464820151056917536153 10.3 262
1503810196497821654867418806.5 16411280
1704318222563924461988321087.3 186 12.5 318
1904826248629927369349323628.2 20814355
16:9 image on a 16:9 Screen
(b) Projection distance
min.max.min.max.
(c) Image height
(d) Vertical offset
13
16:9 image on a 4:3 Screen
(a) Screen Size
inchmminchmminchmminchmminch mm inch mm
541372651651721829256352.2553.793
651651781981862184297372.6664.4112
7619309223371012565348643775.2131
87221010526671152921399913.5885.9149
982489118299712932774411183.9996.6168
1092769131332714436584912454.3110 7.4187
1203048144365815840135413724.8 1218.1205
1313327157398817343945914995.2 1318.8224
1423607170431818747506416265.6 1429.6243
1533886183464820151056917536153 10.3 262
1634140196497821654867418806.5 16411280
1854699222563924461988321087.3 186 12.5 318
2075258248629927369349323628.2 20814355
(b) Projection distance
min.max.min.max.
(c) Image height
(d) Vertical offset
14
PA505W
(b)
(c)
(a)
(d)
(f)
(f): Center of lens(e): Screen
• 16:10 image on a 16:10 screen
• 16:10 image on a 4:3 screen
(b)
(a)
(d)
(c)
(e)
The "screen" mentioned below refers to the projection screen usually consisting of a screen
surface and a support structure.
(a) Screen Size
inchmminchmminchmminchmminch mm inch mm
501270671691731863256351.538
601524802029882236297371.845
7017889323671032608348642.153
80203210727051172981399912.460
902286120304313233544411182.768
1002540133338214737264912453.075
1102794146372016140995413723.383
1203048160405817644725914993.690
1303302173439619148446416263.998
1403556186473420552176917534.2 106
1503810200507222055897418804.5113
1704318226574924963358321085.0 128
1904826253642527970809323625.6 143
16:10 image on a 16:10 Screen
(b) Projection distance
min.max.min.max.
(c) Image height
(d) Vertical offset
15
16:10 image on a 4:3 Screen
(a) Screen Size
inchmminchmminchmminchmminch mm inch mm
541372681723751898276861.538
651651822074902285338261.846
7619309524251052672389652.154
872210109277612030584411052.462
982489123312613634454912452.770
1092769137347715138235513843.178
1203048151382816642186015243.485
1313327165417918146056616443.793
1423607178453019749927118034.0 101
1533886192488121253797719434.3 109
1634140205520022657308220704.6116
1854699232590225665039323505.2 132
20752582606604286727710426295.8147
There is 3% tolerance among these numbers due to optical component variations. It is
recommended that if you intend to permanently install the projector, you should physically
test the projection size and distance using the actual projector in situ before you permanently
install it, so as to make allowance for this projector's optical characteristics. This will help you
determine the exact mounting position so that it best suits your installation location.
(b) Projection distance
min.max.min.max.
(c) Image height
(d) Vertical offset
16
Connection
6
9
5
5
4
3
3
5
8
Y Pb Pr
7
221
Notebook or desktop
computer
A/V device
Speakers
or
Monitor
or(DVI)(VGA)
When connecting a signal source to the projector, be sure to:
1.Turn all equipment off before making any connections.
2.Use the correct signal cables for each source.
3.Ensure the cables are firmly inserted.
In the connections shown below, some cables may not be included with the projector (see
"Shipping contents" on page 5). They are commercially available from electronics stores.
The connection illustrations below are for reference only. The rear connecting jacks available
on the projector vary with each projector model.
For detailed connection methods, see pages 18-20.
1.VGA to DVI-A cable
2.VGA cable
3.HDMI cable
4.RS232 cable
5.Audio cable
6.Video cable
7.USB power supply 5V/1.5A
8.Mini USB cable
9.Component Video to VGA (D-Sub)
adapter cable
17
Connecting a computer or a monitor
Connecting a computer
1.Take the supplied VGA cable and connect one end to the D-Sub output socket of the
computer.
2.Connect the other end of the VGA cable to the COMPUTER IN signal input socket
on the projector.
Many notebooks do not turn on their external video ports when connected to a projector.
Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off. Locate a
function key labeled CRT/LCD or a function key with a monitor symbol on the notebook. Press
FN and the labeled function key simultaneously. Refer to your notebook's documentation to
find your notebook's key combination.
Connecting a monitor
If you want to view your presentation close-up on a monitor as well as on the screen, you
can connect the MONITOR OUT signal output socket on the projector to an external
monitor with a VGA cable following the instructions below:
1.Connect the projector to a computer as described in "Connecting a computer" on page
18.
2.Take a suitable VGA cable (only one supplied) and connect one end of the cable to the
D-Sub input socket of the video monitor.
Or if your monitor is equipped with a DVI input socket, take a VGA to DVI-A cable
and connect the DVI end of the cable to the DVI input socket of the video monitor.
3.Connect the other end of the cable to the MONITOR OUT socket on the projector.
The MONITOR OUT output only works when COMPUTER IN connection is made to the
projector.
To use this connection method when the projector is in standby mode, turn on the Active VGA
Out function under the SOURCE > Standby Settings menu.
Connecting Video source devices
You can connect your projector to various Video source devices that provide any one of the
following output sockets:
• HDMI
• Component Video
• Video (composite)
You need only connect the projector to a Video source device using just one of the above
connecting methods, however each provides a different level of video quality. The method
you choose will most likely depend upon the availability of matching terminals on both the
projector and the Video source device as described below:
Best video quality
The best available video connection method is HDMI. If your source device is equipped
with an HDMI socket, you can enjoy uncompressed digital video quality.
See "Connecting an HDMI device" on page 19for how to connect the projector to an HDMI
source device and other details.
If no HDMI source is available, the next best video signal is Component video (not to be
confused with composite video). Digital TV tuner and DVD players output Component
18
video natively, so if available on your devices, this should be your connection method of
choice in preference to (composite) video.
See "Connecting a Component Video source device" on page 19 for how to connect the
projector to a component video device.
Least video quality
Composite Video is an analog video and will result in a perfectly acceptable, but less than
optimal result from your projector, being the least video quality of the available methods
described here.
See"Connecting a composite Video source device" on page 20for how to connect the
projector to a composite Video device.
Connecting audio
The projector has built-in mono speaker(s) which is designed to provide basic audio
functionality accompanying data presentations for business purposes only. It is not designed
for, nor intended for stereo audio reproduction use as might be expected in home theater or
home cinema applications. Any stereo audio input (if provided), is mixed into a common
mono audio output through the projector speaker.
If you wish, you can make use of the projector (mixed mono) speaker in your presentations,
and also connect separate amplified speakers to the Audio Out socket of the projector. The
audio output is a stereo signal and controlled by the projector Volume and Mute settings.
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
Connecting an HDMI device
You should use an HDMI cable when making connection between the projector and HDMI
devices.
1.Take an HDMI cable and connect one end to the HDMI output port of the video
device.
2.Connect the other end of the cable to the HDMI input port on the projector.
In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI
input and the projected picture displays wrong colors, please change the color space to YUV.
See "Changing HDMI input settings" on page 25 for details.
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See"Connecting audio" on page 19 for details.
Connecting a Component Video source device
Examine your Video source device to determine if it has a set of unused Component Video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
1.Take a VGA (D-Sub)-Component adaptor cable and connect the end with 3 RCA type
connectors to the Component Video output sockets of the Video source device. Match
the color of the plugs to the color of the sockets; green to green, blue to blue, and red
to red.
2.Connect the other end of the VGA (D-Sub)-Component adaptor cable (with a D-Sub
type connector) to the COMPUTER IN socket on the projector.
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See"Connecting audio" on page 19 for details.
19
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
Connecting a composite Video source device
Examine your Video source device to determine if it has a set of unused composite Video
output sockets available:
• If so, you can continue with this procedure.
• If not, you will need to reassess which method you can use to connect to the device.
1.Take a Video cable and connect one end to the composite Video output socket of the
Video source device.
2.Connect the other end of the Video cable to the VIDEO socket on the projector.
The projector is only capable of playing mixed mono audio, even if a stereo audio input is
connected. See"Connecting audio" on page 19 for details.
If the selected video image is not displayed after the projector is turned on and the correct
video source has been selected, check that the Video source device is turned on and
operating correctly. Also check that the signal cables have been connected correctly.
You need only connect to this device using a composite Video connection if Component Video
input is unavailable for use. See"Connecting Video source devices" on page 18for details.
Playing sound through the projector
You can make use of the projector (mixed mono) speaker in your presentations, and also
connect separate amplified speakers to the AUDIO OUT socket of the projector.
If you have a separate sound system, you will most likely want to connect the audio output
of your Video source device to that sound system, instead of to the mono audio projector.
Once connected, the audio can be controlled by the projector On-Screen Display (OSD)
menus. See "Adjusting the sound" on page 36 for details.
20
Operation
Starting up the projector
1.Plug the power cord into the projector and into a wall socket. Turn on the wall socket
switch (where fitted).
2.(If available) Remove the lens cap.
3.Press Power to start the projector. As soon as the lamp lights up, a "Power On Ring
Tone" will be heard. The Power indicator light stays blue when the projector is on.
(If necessary) Rotate the focus ring to adjust the image clearness.
If the projector is still hot from previous activity, it will run the cooling fan for approximately 60
seconds before energizing the lamp.
To maintain the lamp life, once you turn the projector on, wait at least 5 minutes before turning
it off.
To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 36 for details.
4.If the projector is activated for the first time, select your OSD language following the
on-screen instructions.
5.Switch all of the connected equipment on.
6.The projector will start to search for input signals. The current input signal being
scanned appears in the bottom right corner of the screen. If the projector doesn't detect
a valid signal, the message 'No Signal' will continue to be displayed until an input
signal is found.
You can also press Source to select your desired input signal. See "Switching input
signal" on page 25 for details.
If the frequency/resolution of the input signal exceeds the projector's operating range, you will
see the message 'Out of Range'displayed on a blank screen. Please change to an input signal
which is compatible with the projector's resolution or set the input signal to a lower setting.
See "Timing chart" on page 53 for details.
21
Using the menus
Current input signal
Main menu icon
Sub-menu
Highlight
Go to the
previous page
or to exit.
Status
The projector is equipped with On-Screen Display (OSD) menus for making various
adjustments and settings.
The OSD screenshots below are for reference only, and may differ from the actual design.
Below is the overview of the OSD menu.
To use the OSD menus, please select your language first.
1.Press Menu to turn the OSD menu on.
2.Use / to highlight the SYSTEM
menu.
3.Press to highlight
Language and press Enter.
Then press // / to
select a preferred language.
4.Press Exit twice* to leave and
save the settings.
*The first press leads you back
to the main menu and the
second press closes the OSD
menu.
22
Utilizing the password function
For security purposes and to help prevent unauthorized use, the projector includes an option
for setting up password security. The password can be set through the On-Screen Display
(OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on
page 22.
You will be inconvenienced if you enable the password function yet forget the password
somehow. Do make a note of your password, and keep the note in a safe place for later recall.
Setting a password
Once a password has been set and the power on lock is enabled, the projector cannot be used
unless the correct password is entered every time the projector is started.
1.Open the OSD menu and go to the SYSTEM > Security Settings > Change
Password menu.
2.Press Enter and the password dialog box is displayed.
3.Highlight Power On Lock and select On by pressing / .
4.As pictured to the right, the four arrow keys
( ,,, ) respectively represent 4 digits (1, 2, 3,
4). According to the password you desire to set, press
the arrow keys to enter six digits for the password.
5.Confirm the new password by re-entering the new
password.
Once the password is set, the OSD menu returns to the
Security Settings page.
6.To leave the OSD menu, press Exit.
If you forget the password
If the password function is activated, you will be
asked to enter the six-digit password every time you
turn on the projector. If you enter the wrong
password, the password error message as pictured
to the right is displayed lasting for 5 seconds, and
the message 'INPUT PASSWORD' follows. You
can retry by entering another six-digit password, or if you did not record the password in
this user manual, and you absolutely do not remember it, you can use the password recall
procedure. See "Entering the password recall procedure" on page 24 for details.
If you enter an incorrect password 5 times in succession, the projector will automatically
shut down in a short time.
23
Entering the password recall procedure
1.Press and hold Auto Sync on the remote control for
3 seconds. The projector will display a coded
number on the screen.
2.Write down the number and turn off your projector.
3.Seek help from the local service center to decode
the number. You may be required to provide proof
of purchase documentation to verify that you are an
authorized user of the projector.
The "XXX" shown in the above screenshot are numbers
that vary depending on different projector models.
Changing the password
1.Open the OSD menu and go to the SYSTEM > Security Settings > Change
Password menu.
2.Press Enter. The message 'INPUT CURRENT PASSWORD' is displayed.
3.Enter the old password.
•If the password is correct, another message 'INPUT NEW PASSWORD' is
displayed.
•If the password is incorrect, the password error message is displayed lasting for
5 seconds, and the message 'INPUT CURRENT PASSWORD' is displayed
for your retry. You can press Exit to cancel or try another password.
4.Enter a new password.
5.Confirm the new password by re-entering the new password.
6.You have successfully assigned a new password to the projector. Remember to enter
the new password next time the projector is started.
7.To leave the OSD menu, press Exit.
The digits being input will be displayed as asterisks on-screen. Do make a note of your
password, and then keep the note in a safe place for later recall.
Disabling the password function
1.Open the OSD menu and go to the SYSTEM > Security Settings > Power On Lock
menu.
2.Press / to select Off.
3.The message 'INPUT PASSWORD' is displayed. Enter the current password.
•If the password is correct, the OSD menu returns to the Security Settings page
with 'Off' shown in the row of Power On Lock. You will not have to enter the
password next time you turn on the projector.
•If the password is incorrect, the password error message is displayed lasting for
5 seconds, and the message 'INPUT PASSWORD' is displayed for your retry.
You can press Exit to cancel or try another password.
Though the password function is disabled, you need to keep the old password in hand should
you ever need to re-activate the password function by entering the old password.
24
Switching input signal
The projector can be connected to multiple devices at the same time. However, it can only
display one full screen at a time.
Be sure the Quick Auto Search function in the SYSTEM menu is On if you want the
projector to automatically search for the signals.
You can also manually select the desired signal by
pressing one of the source selection keys on the
remote control, or cycle through the available input
signals.
1.Press Source. A source selection bar is
displayed.
2.Press / until your desired signal is
selected and press Enter.
Once detected, the selected source information
will be displayed on the screen for seconds. If there are multiple devices connected to
the projector, repeat steps 1-2 to search for another signal.
Please see "Projector specifications" on page 51 for the native display resolution of this
projector. For best display picture results, you should select and use an input signal which
outputs at this resolution. Any other resolutions will be scaled by the projector depending
upon the 'aspect ratio' setting, which may cause some image distortion or loss of picture
clarity. See "Selecting the aspect ratio" on page 28 for details.
Changing HDMI input settings
In the unlikely event that you connect the projector to a device (like a DVD or Blu-ray
player) via the projector’s HDMI input and the projected picture displays wrong colors,
please change the color space to an appropriate one that fits the color space setting of the
output device.
To do this:
1.Open the OSD menu and go to the ADVANCED > HDMI Settings menu.
2.Press Enter.
3.Highlight HDMI Settings and press / to select a suitable color space according
to the color space setting of the output device connected.
•RGB: Sets the color space as RGB.
•YUV: Sets the color space as YUV.
•Auto: Sets the projector to detect the color space setting of the input signal
automatically.
4.Highlight HDMI Range and press / to select a suitable HDMI color range
according to the color range setting of the output device connected.
•Enhanced: Sets the HDMI color range as 0 - 255.
•Normal: Sets the HDMI color range as 15 - 235.
•Auto: Sets the projector to detect the HDMI range of the input signal
automatically.
This function is only available when the HDMI input port is in use.
Refer to the documentation of the device for information on the color space and HDMI range
settings.
25
Adjusting the projected image
Adjusting the projection angle
The projector is equipped with two adjuster foot. It changes the image height and vertical
projection angle. Screw the adjuster foot to fine tune the angle until the image is positioned
where you want it.
If the projector is not placed on a flat surface or the screen and the projector are not
perpendicular to each other, the projected image becomes trapezoidal. To correct this
situation, see "Correcting keystone" on page 27 for details.
Do not look into the lens while the lamp is on. The strong light from the lamp may cause
damage to your eyes.
Auto-adjusting the image
In some cases, you may need to optimize the picture quality. To do this, press Auto Sync on
the remote control. Within 5 seconds, the built-in Intelligent Auto Adjustment function will
re-adjust the values of Frequency and Clock to provide the best picture quality.
The current source information will be displayed in the upper left corner of the screen for 3
seconds.
The screen will be blank while auto adjustment is functioning.
This function is only available when PC D-Sub input signal (analog RGB) is selected.
26
Fine-tuning the image clarity
Press /
Press /
1.Adjust the projected image to the size
that you need using the zoom ring.
2.If necessary, sharpen the image by rotating
the focus ring.
Correcting keystone
Keystoning refers to the situation where the projected image becomes a trapezoid due to
angled projection.
To correct this, besides adjusting the height of the projector, you will need to manually
correct it following one of these steps.
• Using the remote control
1.Press / to display the Keystone
correction page.
2.Press to correct keystoning at the top of
the image. Press to correct keystoning at
the bottom of the image.
• Using the OSD menu
1.Open the OSD menu and go to the
2.Press Enter. The Keystone correction page is displayed.
3.Press to correct keystoning at the top of the image or press to correct
keystoning at the bottom of the image.
DISPLAY > Keystone menu.
Magnifying and searching for details
If you need to find the details on the projected picture, magnify the picture. Use the
direction arrow keys for navigating the picture.
• Using the remote control
•Press remote control ( and ) for screen zoom in or zoom out
• Using the OSD menu
1.Open the OSD menu and go to the
2.Press Enter. The Zoom bar is displayed.
3.To navigate the picture, press Enter to switch to the paning mode and press the
directional arrows ( ,,,) to navigate the picture.
4.To reduce size of the picture, press Enter to switch back to the zoom in/out
functionality, and press repeatedly until it is restored to the original size. You can
also press Auto Sync on the remote control to restore the picture to its original size.
The picture can only be navigated after it is magnified. You can further magnify the picture
while searching for details.
DISPLAY > Zoom menu.
27
Selecting the aspect ratio
16:10 picture
16:9 picture
4:3 picture
16:9 picture
16:10 picture
The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and
computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio.
With the advent of digital signal processing, digital display devices like this projector can
dynamically stretch and scale the image output to a different aspect than that of the image
input signal.
To change the projected image ratio (no matter what aspect the source is):
• Using the remote control
•Press Aspect on the remote until your desired mode is selected.
• Using the OSD menu
1.Open the OSD menu and go to the
2.Press / to select an aspect ratio to suit the format of the video signal and your
display requirements.
About the aspect ratio
In the pictures below, the black portions are inactive areas and the white portions are active
areas. OSD menus can be displayed on those unused black areas.
1.Auto: Scales an image proportionally to fit the
projector's native resolution in its horizontal
width. This is suitable for the incoming image
which is neither in 4:3 nor 16:9 and you want
to make most use of the screen without altering
the image's aspect ratio.
DISPLAY > Aspect Ratio menu.
2.4:3: Scales an image so that it is displayed in
the center of the screen with a 4:3 aspect ratio.
This is most suitable for 4:3 images like
computer monitors, standard definition TV and
4:3 aspect DVD movies, as it displays them
without aspect alteration.
3.16:9 (PX705HD): Scales an image so that it is
displayed in the center of the screen with a 16:9
aspect ratio. This is most suitable for images
which are already in a 16:9 aspect, like high
definition TV, as it displays them without
aspect alteration.
4.16:10 (PA505W): Scales an image so that it is
displayed in the center of the screen with a
16:10 aspect ratio. This is most suitable for
images which are already in a 16:10 aspect, as
it displays them without aspect alteration.
28
5.Panorama: Scales a 4:3 image vertically and
4:3 picture
2.35:1 picture
2.35:1 picture
horizontally in a non-linear manner so that it
fills the screen.
6.2.35:1: Scales an image so that it is displayed
in the center of the screen with a 2.35:1 aspect
ratio without aspect alteration.
7.Anamorphic: Scales a 2.35:1 aspect image so
that it fills the screen.
Optimizing the image
Selecting a picture mode
The projector is preset with several predefined picture modes so that you can choose one to
suit your operating environment and input signal picture type.
To select an operation mode that suits your need, you can follow one of the following steps.
• Press Color Mode on the remote control until your desired mode is selected.
•Go to the IMAGE > Color Mode menu and press / to select a desired mode.
Picture modes for different types of signals
The picture modes available for different types of signals are listed below.
1.Brightest mode: Maximizes the brightness of the projected image. This mode is
suitable for environments where extra-high brightness is required, such as using the
projector in well lit rooms.
2.Sport (PX705HD): Optimized for viewing sport match in well-lit environments.
3.Presentation mode (PA505W): Is designed for presentations under daylight
environment to match PC and notebook coloring.
4.Standard mode: Is designed for presentations under daylight environment to match
PC and notebook coloring.
5.Gaming (PX705HD): Suitable for playing video games in a bright living room.
6.Photo mode (PA505W): Is designed for photo viewing.
7.Movie mode: Is appropriate for playing colorful movies, video clips from digital
cameras or DVs through the PC input for best viewing in a blackened (little light)
environment.
29
Using Screen Color
50
-30
+80
40
In the situation where you are projecting onto a colored surface such as a painted wall which
may not be white, the Screen Color feature can help correct the projected picture’s colors to
prevent possible color difference between the source and projected pictures.
To use this function, go to the DISPLAY > Screen Color menu and press / to select a
color which is closest to the color of the projection surface. There are several precalibrated
colors to choose from: Whiteboard, Greenboard, and Blackboard. The effects of these
settings may vary depending on different models.
This function is only available when a PC or HDMI input signal is selected.
Fine-tuning the image quality in user modes
According to the detected signal type, there are some user-definable functions available.
You can make adjustments to these functions based on your needs.
Adjusting Brightness
Go to the IMAGE > Brightness menu and press / .
The higher the value, the brighter the image. And the
lower the setting, the darker the image. Adjust this
control so the black areas of the image appear just as
black and that detail in the dark areas is visible.
Adjusting Contrast
Go to the IMAGE > Contrast menu and press / .
The higher the value, the greater the contrast. Use this
to set the peak white level after you have previously
adjusted the Brightness setting to suit your selected
input and viewing environment.
Adjusting Color
Go to the IMAGE > ADVANCED > Color menu and press / .
Lower setting produces less saturated colors. If the setting is too high, colors on the image
will be overpowering, which makes the image unrealistic.
This function is only available when the input signal is Video, YPbPr or YCbCr.
Adjusting Tint
Go to the IMAGE > ADVANCED > Tint menu and press / .
The higher the value, the more reddish the picture becomes. The lower the value, the more
greenish the picture becomes.
This function is only available when the input signal is Video, YPbPr or YCbCr.
Adjusting Sharpness
Go to the IMAGE > ADVANCED > Sharpness menu and press / .
The higher the value, the sharper the picture becomes. The lower the value, the softer the
picture becomes.
This function is only available when the input signal is Video, YPbPr or YCbCr.
-30
0
+
30
Adjusting Brilliantcolor
Go to the IMAGE > ADVANCED > Brilliantcolor menu and press / .
This feature utilizes a new color-processing algorithm and system level enhancements to
enable higher brightness while providing truer, more vibrant colors in the projected picture.
It enables a greater than 50% brightness increase in mid-tone images, which are common in
video and natural scenes, so the projector reproduces images in realistic and true colors. If
you prefer images with that quality, select a level that suits your need. If you don’t need it,
select Off.
Reducing image noise
Go to the IMAGE > ADVANCED > Noise Reduction menu and press / .
This function reduces electrical image noise caused by different media players. The higher
the setting, the less the noise.
This function is only available when a PC, or Video input signal is selected.
Selecting a gamma setting
Go to the IMAGE > ADVANCED > Gamma menu and select a preferred setting by
pressing / .
Gamma refers to the relationship between input source and picture brightness.
Selecting a Color Temperature
Go to the IMAGE > Color Temp menu and press / .
The options available for color temperature settings vary according to the signal type
selected.
1.Cool: With the highest color temperature, Cool makes the image appear the most
bluish white than other settings.
2.Normal: Maintains normal colorings for white.
3.Warm: Makes images appear reddish white.
Setting a preferred color temperature
1.Go to the IMAGE > Color Temp menu.
2.Press / to select Cool, Normal or Warm and press Enter.
3.Press / to highlight the item you want to change and adjust the values by
pressing /
•Red Gain/Green Gain/Blue Gain: Adjusts the contrast levels of Red, Green,
and Blue.
•Red Offset/Green Offset/Blue Offset: Adjusts the brightness levels of Red,
Green, and Blue.
This function is only available when a PC input signal is selected.
.
31
Color Management
RED
BLUE
GREEN
Yellow
Cyan
Magenta
Only in permanent installations with controlled lighting levels such as boardrooms, lecture
theaters, or home theaters, should color management be considered. Color management
provides fine color control adjustment to allow for more accurate color reproduction, should
you require it.
If you have purchased a test disc which contains various color test patterns and can be used
to test the color presentation on monitors, TVs, projectors, etc., you can project any image
from the disc on the screen and enter the Color Management menu to make adjustments.
To adjust the settings:
1.Open the OSD menu and go to the IMAGE > ADVANCED > Color Management
menu.
2.Press Enter and the Color Management page is displayed.
3.Highlight Primary Color and press / to select a color from among Red, Yellow,
Green, Cyan, Blue, or Magenta.
4.Press to highlight Hue and press / to select its range. Increase in the range
will include colors consisted of more proportions of its two adjacent colors.
Please refer to the illustration to the right for
how the colors relate to each other.
For example, if you select Red and set its
range at 0, only pure red in the projected
picture will be selected. Increasing its range
will include red close to yellow and red close
to magenta.
5.Press to highlight Saturation and adjust
its values to your preference by pressing /
. Every adjustment made will reflect to the
image immediately.
For example, if you select Red and set its
value at 0, only the saturation of pure red will
be affected.
Saturation is the amount of that color in a video picture. Lower settings produce less
saturated colors; a setting of “0” removes that color from the image entirely. If the saturation
is too high, that color will be overpowering and unrealistic.
6.Press to highlight Gain and adjust its values to your preference by pressing / .
The contrast level of the primary color you select will be affected. Every adjustment
made will reflect to the image immediately.
7.Repeat steps 3 to 6 for other color adjustments.
8.Make sure you have made all of the desired adjustments.
9.Press Exit to exit and save the settings.
32
Setting the presentation timer
Presentation timer can indicate the presentation time on the screen to help you achieve
better time management when giving presentations. Follow these steps to utilize this
function:
1.Go to the BASIC > Presentation Timer menu.
2.Press Enter to display the Presentation Timer page.
3.Highlight Timer Period and decide the time period by pressing / . The length of
time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5minute increments.
If the timer is already on, the timer will restart whenever the Timer Period is reset.
4.Press to highlight Timer Display and choose if you want the timer to show up on
the screen by pressing
SelectionDescription
Always
1 min/2 min/3 min Displays the timer on screen in the last 1/2/3 minute(s).
NeverHides the timer throughout the presentation time.
5.Press to highlight Timer Position and set the timer position by pressing / .
Top-LeftBottom-LeftTop-RightBottom-Right
6.Press to highlight Timer Counting Direction and select your desired counting
direction by pressing / .
SelectionDescription
Count UpIncreases from 0 to the preset time.
Count DownDecreases from the preset time to 0.
/ .
Displays the timer on screen throughout the presentation
time.
7.Press to highlight Sound Reminder and decide if you want to activate sound
reminder by pressing / . If you select On, a double beep sound will be heard at
the last 30 seconds of counting down/up, and a triple beep sound will be produced
when the timer is up.
8.To activate the presentation timer, press and press / to highlight Start Counting and press Enter.
9.A confirmation message displays. Highlight Yes and press Enter to confirm. You will
see the message “Timer is On” displaying on the screen. The timer starts counting
when the timer is on.
To cancel the timer, perform the following steps:
1.Go to the BASIC > Presentation Timer menu.
2.Highlight Off. Press Enter. A confirmation message displays.
3.Highlight Yes and press Enter to confirm. You will see the message “Timer is Off”
displaying on the screen.
33
Hiding the image
In order to draw the audience's full attention to the presenter, you can press BLANK to hide
the screen image. Press any key on the projector or remote control to restore the image.The
word 'BLANK' appears at the lower right corner of the screen while the image is hidden.
You can set the blank time in the BASIC
the image automatically after a period of time when there is no action taken on the blank
screen.
Once Blank is pressed, the projector enters SuperEco mode automatically.
CAUTION
Do not block the projection lens from projecting as this could cause the blocking object to
become heated and deformed or even cause a fire.
> Blank Timer menuto let the projector return
Locking control keys
With the control keys on the projector locked, you can prevent your projector settings from
being changed accidentally (by children, for example). When the Panel Key Lock is on, no
control keys on the projector will operate except Power.
1.Go to the
2.Press / to select On.
3.A confirmation message is displayed. Select Yes to confirm.
You can also use the remote control to enter the
press / to select Off.
Keys on the remote control are still functional when panel key lock is enabled.
If you press Power to turn off the projector without disabling panel key lock, the projector
will still be in locked status the next time it is turned on.
SYSTEM > Panel Key Lock menu.
SYSTEM > Panel Key Lock menu and
Operating in a high altitude environment
We recommend you use the High Altitude Mode when your environment is between 1500
m–3000 m above sea level, and temperature is between 5°C–25°C.
CAUTION
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature
is between 5°C and 35°C. The projector will be over cooled, if you turn the mode on under
such a condition.
To activate the High Altitude Mode:
1.Open the OSD menu and go to the SYSTEM > High Altitude Mode menu.
2.Press / to select On. A confirmation message is
displayed.
3.Highlight Yes and press Enter.
Operation under "High Altitude Mode" may cause a higher
decibel operating noise level because of increased fan speed
necessary to improve overall system cooling and performance.
If you use this projector under other extreme conditions excluding the above, it may display
auto shut-down symptoms, which is designed to protect your projector from over-heating.
In cases like this, you should switch to High Altitude Mode to solve these symptoms.
34
However, this is not to state that this projector can operate under any and all harsh or
extreme conditions.
Using the CEC function
This projector supports CEC (Consumer Electronics Control) function for synchronized
power on/off operation via HDMI connection. That is, if a device that also supports CEC
function is connected to the HDMI input of the projector, when the projector’s power is
turned off, the power of the connected device will also be turned off automatically. When
the power of the connected device is turned on, the projector’s power will be turned on
automatically.
To turn on the CEC function:
1.Open the OSD menu and go to the POWER MANAGEMENT > Auto Power On >
CEC menu.
2.Press / to select All.
In order for the CEC function to work properly, make sure that the device is correctly
connected to the HDMI input of the projector via an HDMI cable, and its CEC function is turned
on.
Depending on the connected device, the CEC function may not work.
Using the 3D functions
This projector features 3D function which enables you to enjoy 3D movies, videos, and
sporting events in a more realistic way by presenting the depth of the images. You need to
wear a pair of 3D glasses to view 3D images.
If the 3D signal is input from an HDMI 1.4a compatible device, the projector detects the
signal for 3D Sync information and once detected, it projects images in 3D format
automatically. In other cases, you may need to manually select a 3D Sync format for the
projector to project 3D images correctly.
To select a 3D Sync format:
1.Press 3D on the remote control to access the 3D Settings menu or go to the
ADVANCED > 3D Settings menu.
2.Press Enter. The 3D Settings page is displayed.
3.Highlight 3D Sync and press Enter.
4.Press
When the 3D Sync function is on:
• The brightness level of the projected image will decrease.
• The Color Mode and Zoom function cannot be adjusted.
If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to “Invert”
to correct the problem.
to select a 3D Sync setting and then press Enter to confirm.
35
Using the projector in standby mode
Some of the projector functions are available in standby mode (plugged in but not turned
on). To use these functions, be sure you have turned on the corresponding menus under
POWER MANAGEMENT > Standby Settings, and the cable connections are correctly
made. For the connection methods, see the Connection chapter.
Active Audio Out
Selecting On outputs an audio signal when the AUDIO IN socket is correctly connected to
a proper device.
Active VGA Out
Selecting On in the POWER MANAGEMENT > Standby Settings > Active VGA Out
outputs a VGA signal when the COMPUTER IN 1 and MONITOR OUT sockets are
correctly connected to devices. The projector outputs the signal received only from
COMPUTER IN 1.
Adjusting the sound
The sound adjustments made as below will have an effect on the projector speaker. Be sure
you have made a correct connection to the projector audio input/output jacks. See
"Connection" on page 17 for more details.
Muting the sound
1.Open the OSD menu and go to the BASIC > Audio Settings > Mute menu.
2.Press / to select On.
If available, you can press on the remote control to toggle the projector audio between on
and off.
Adjusting the sound level
1.Open the OSD menu and go to the BASIC > Audio Settings > Audio Volume menu.
2.Press / to select a desired sound level.
If available, you can press or on the remote control to adjust the projector’s sound
level.
Turning off the Power On/Off Ring Tone
1.Open the OSD menu and go to the BASIC > Audio Settings > Power On/Off Ring
Tone menu.
2.Press / to select Off.
The only way to change Power On/Off Ring Tone is setting On or Off here. Setting the sound
mute or changing the sound level will not affect the Power On/Off Ring Tone.
36
Shutting down the projector
1.Press Power and a confirmation message is displayed prompting you.
If you don't respond in a few seconds, the message will disappear.
2.Press Power a second time.
3.Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect
the power cord from the wall socket if the projector will not be used in an extended
period of time.
To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 36 for details.
CAUTION
• To protect the lamp, the projector will not respond to any commands during the cooling
process.
• To shorten the cooling time, you can also activate the Quick Power Off function. See
"Quick Power Off" on page 43 for details.
• Do not unplug the power cord before the projector shutdown sequence is complete.
37
Menu operation
Menu system
Please note that the on-screen display (OSD) menus vary according to the signal type
selected.
The menu items are available when the projector detects at least one valid signal. If there is
no equipment connected to the projector or no signal detected, limited menu items are
accessible.
DCROff/On
Closed
Caption
Reset
Settings
LanguageMulti-language OSD selection
Projector
Position
Menu
Settings
High Altitude
Mode
Quick Auto
Search
Security
Settings
Panel Key
Lock
Remote
Control Code
Baud Rate
Current System Status
3D Sync
Invert
HDMI Format Auto/RGB/YUV
HDMI Range Auto/Enhanced/Normal
Lamp ModeNormal/Eco/Dynamic/SuperEco
Reset Lamp
Hours
Lamp Hours
Menu Display
Time
Menu
Position
Change
Password
Power on
Lock
40
Description of each menu
FunctionDescription
See "Using Screen Color" on page 30 for details.
Screen Color
Aspect RatioSee "Selecting the aspect ratio" on page 28 for details.
KeystoneSee "Correcting keystone" on page 27 for details.
Position
1. DISPLAY menu
Phase
H. Size
ZoomSee "Magnifying and searching for details" on page 27 for details.
OverScan
3X Fast Input
This function is only available when a PC input signal is
selected.
Displays the position adjustment page. To move the projected
image, use the directional arrow keys. The values shown on the
lower position of the page change with every key press you made
until they reach their maximum or minimum.
This function is only available when a PC input signal is
selected.
The adjustment range may vary under different timings.
Adjusts the clock phase to reduce image
distortion.
This function is only available when a
PC input signal is selected.
Adjusts the horizontal width of the image.
This function is only available when a PC input signal is
selected.
Adjusts the overscan rate from 0% to 5%.
This function is only available when a Composite Video or
HDMI input signal is selected.
Selecting Active enables the function. This function is favorable to
frame rate reducing. Quick response time in native timing can be
achieved. When enabled, the following settings will return to
factory preset values: Aspect Ratio, Keystone, Position, Zoom,
OverScan.
This function is only available when a native timing input
signal is selected.
41
FunctionDescription
Color ModeSee "Selecting a picture mode" on page 29 for details.
BrightnessSee "Adjusting Brightness" on page 30 for details.
ContrastSee "Adjusting Contrast" on page 30 for details.
Color Temp
See "Selecting a Color Temperature" on page 31 and "Setting a
preferred color temperature" on page 31 for details.
Color
See "Adjusting Color" on page 30 for details.
Tint
2. IMAGE menu
See "Adjusting Tint" on page 30 for details.
The function is only available when Video input with NTSC
system is selected.
Sharpness
See "Adjusting Sharpness" on page 30 for details.
ADVANCED
Gamma
See "Selecting a gamma setting" on page 31 for details.
Brilliantcolor
See "Adjusting Brilliantcolor" on page 31 for details.
Noise Reduction
See "Reducing image noise" on page 31 for details.
Color Management
See "Color Management" on page 32 for details.
Reset Color
Settings
Returns all color settings to the factory preset values.
42
FunctionDescription
Signal
Selecting All allows the projector to turn on automatically once the
VGA/HDMI signal is fed through the VGA/HDMI cable.
Auto Power On
CEC
See "Using the CEC function" on page 35 for details.
Direct Power On
Selecting On allows the projector to turn on automatically once the
power is fed through the power cord.
Auto Power Off
3. POWER MANAGEMENT menu
Smart Energy
See "Setting Auto Power Off" on page 47 for details.
Sleep Timer
See "Setting Sleep Timer" on page 47 for details.
Power Saving
See "Setting Power Saving" on page 48 for details.
Standby
See "Using the projector in standby mode" on page 36 for details.
Settings
Selecting Enable you to restart the projector immediately within
120 seconds after turning it off. After 120 seconds, if the projector
is not turned on again, it will directly enter the standby mode.
Smart Restart
It takes some time to initiate this function. Make sure the
projector has been turned on for more than 4 minutes. If the
projector is resumed by using the Smart Restart feature, this
function can be executed immediately.
When Enable is selected, the Quick Power Off function will be
automatically set to “On”.
Selecting Enable enables the function and the projector will not
enter the cooling process after being shut down. Selecting Disable
disables the function and the projector will enter normal cooling
process after being shut down.
Quick Power Off
If you attempt to restart the projector right after it’s been
turned off, it may not be turned on successfully and will rerun
its cooling procedure.
When Disable is selected, the Smart Restart function will be
automatically turned off.
Audio Settings See "Adjusting the sound" on page 36 for details.
Presentation
4. BASIC menu
Timer
See "Setting the presentation timer" on page 33 for details.
The projector can display grid test patterns. It helps you adjust the
Pattern
image size and focus and check that the projected image is free
from distortion.
Blank TimerSee "Hiding the image" on page 34 for details.
Message
Splash Screen
Selecting On displays the current information on the screen when
the projector is detecting or searching for a signal.
Allows you to select which logo screen will be displayed during
projector start-up.
43
FunctionDescription
3D SettingsSee "Using the 3D functions" on page 35 for details.
HDMI SettingsSee "Changing HDMI input settings" on page 25 for details.
Lamp Mode
See "Setting Lamp Mode" on page 47 for details.
Reset Lamp Hours
Lamp Settings
Resets the lamp timer after new lamp is installed. For changing the
lamp, please contact qualified service personnel.
Lamp Hours
5. ADVANCED menu
See "Getting to know the lamp hour" on page 47 for details on how
the total lamp hour is calculated.
Enables or disables the DCR (Dynamic Contrast Ratio) function.
Selecting On enables the function and the projector will
automatically switch the lamp mode between normal and economic
modes according to the input image detected.
DCR
This function is only available when a PC input signal is
selected.
After enabling DCR, frequent lamp mode switching may
shorten lamp life and noise level will vary during operation.
Caption Version
Closed Caption
Selects a preferred closed captioning mode. To view captions,
select CC1, CC2, CC3, or CC4 (CC1 displays captions in the
primary language in your area).
Returns all settings to the factory preset values.
Reset Settings
The following settings will still remain: Keystone, OverScan,
Language, Projector Position, High Altitude Mode, Security
Settings, Remote Control Code, 3D Settings.
44
FunctionDescription
Language
Projector
Position
Menu Settings
6. SYSTEM menu
High Altitude
Mode
Quick Auto
Search
Security
Settings
Panel Key Lock See "Locking control keys" on page 34 for details.
Remote Control
Code
Baud RateSelects RS232 baud rate.
7. INFORMATION menu
Current System
Status
Sets the language for the On-Screen Display (OSD) menus. See
"Using the menus" on page 22 for details.
See "Choosing a location" on page 12 for details.
Menu Display Time
Sets the length of time the OSD will remain active after your last
key press. The range is from 5 to 30 seconds in 5-second
increments.
Menu Position
Sets the On-Screen Display (OSD) menu position.
A mode for operation in high altitude areas.
See "Switching input signal" on page 25 for details.
See "Utilizing the password function" on page 23 for details.
See "Remote control code" on page 9 for details.
Source
Shows the current signal source.
Color Mode
Shows the selected mode in the IMAGE menu.
Resolution
Shows the native resolution of the input signal.
Color System
Shows input system format.
Firmware Version
Shows the current firmware version.
3X Fast Input
Shows whether the function is activated or not.
S/N
Shows the project serial number.
45
Maintenance
Care of the projector
You need to keep the lens and/or filter (optional accessory) clean on a regular basis.
Never remove any parts of the projector. Contact your dealer when any part of the projector
needs replacing.
Cleaning the lens
Clean the lens whenever you notice dirt or dust on the surface.
• Use a canister of compressed air to remove dust.
• If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens
cleaner and gently wipe the lens surface.
CAUTION
Never rub the lens with abrasive materials.
Cleaning the projector case
Before you clean the case, turn the projector off using the proper shutdown procedure as
described in "Shutting down the projector" on page 37 and unplug the power cord.
• To remove dirt or dust, wipe the case with a soft, lint-free cloth.
• To remove stubborn dirt or stains, moisten a soft cloth with water and a neutral pH
detergent. Then wipe the case.
CAUTION
Never use wax, alcohol, benzene, thinner or other chemical detergents. These can damage the case.
Storing the projector
If you need to store the projector for an extended time, please follow the instructions below:
• Make sure the temperature and humidity of the storage area are within the
recommended range for the projector. Please refer to"Specifications" on page 51 or
consult your dealer about the range.
• Retract the adjuster foot.
• Remove the battery from the remote control.
• Pack the projector in its original packing or equivalent.
Transporting the projector
It is recommended that you ship the projector with its original packing or equivalent.
46
Lamp information
Getting to know the lamp hour
When the projector is in operation, the duration (in hours) of lamp usage is automatically
calculated by the built-in timer.
To obtain the lamp hour information:
1.Open the OSD menu and go to the ADVANCED > Lamp Settings menu.
2.Press Enter and the Lamp Settings page is displayed.
3.You will see the Lamp Hours information on the menu.
4.To leave the menu, press Exit.
Extending lamp life
The projection lamp is a consumable item. To keep the lamp life as long as possible, you
can do the following settings via the OSD menu.
Setting Lamp Mode
Setting the projector In Eco/Dynamic/SuperEco mode reduces system noise, power
consumption and extends the lamp operation life.
Lamp modeDescription
NormalProvide full lamp brightness.
ECO
Dynamic
SuperEco
It is not recommended to use SuperEco mode on projection for long time.
To set the lamp mode, go to the ADVANCED > Lamp Settings > Lamp Mode menu and
press / to select Eco.
Setting Auto Power Off
This function allows the projector to turn off automatically after a set period of time once no
input source is detected to prevent unnecessary waste of lamp life.
1.Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy
menu.
2.Press Enter and the Smart Energy page is displayed.
3.Highlight Auto Power Off and press / .
4.If the preset time lengths are not suitable for your need, select Disable. The projector
will not automatically shut down in a certain time period.
Reduce lamp power consumption by 20% and lower brightness to extend
the lamp life and decrease the fan noise.
Reduce lamp power consumption by 0~ 70% base on the signal and lower
brightness to extend the lamp life and decrease the fan noise.
Reduce lamp power consumption by 70% and lower brightness to extend
the lamp life and decrease the fan noise.
Setting Sleep Timer
This function allows the projector to turn off automatically after a set period of time to
prevent unnecessary waste of lamp life.
1.Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy
menu.
2.Press Enter and the Smart Energy page is displayed.
3.Highlight Sleep Timer and press / .
47
4.If the preset time lengths are not suitable for your need, select Disable. The projector
will not automatically shut down in a certain time period.
Setting Power Saving
The projector lowers the power consumption if no input source is detected after 5 minutes to
prevent unnecessary waste of lamp life. You can further decide if you would like the
projector to turn off automatically after a set period of time.
1.Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy
menu.
2.Press Enter and the Smart Energy page is displayed.
3.Highlight Power Saving and press / .
4.When Enable is selected, the projector lamp will be changed to Eco mode after no
signal is detected for 5 minutes.
The lamp power will be changed to SuperEco mode after no signal is detected for 20
minutes.
Timing of replacing the lamp
Please install a new lamp or consult your dealer when the Lamp indicator light lights up. An
old lamp may cause a malfunction in the projector and in some instances the lamp may
explode.
CAUTION
The Lamp indicator light and Temperature indicator light will light up if the lamp becomes too
hot. Turn the power off and let the projector cool for 45 minutes. If the Lamp indicator light or
Temperature indicator light still lights up after turning the power back on, please contact your
dealer. See "Indicators" on page 49 for details.
Replacing the lamp
Turn the power off and disconnect the projector from the power outlet. Please contact
qualified service personnel for changing the lamp.
48
Indicators
Light
Blue
ONOffOff
FlashingOffOff
FlashingOffOff
7 blinksOffOff
8 blinksOffOff
9 blinksOffOff
5 blinksOffOff
5 blinksOff1 blinks
5 blinksOff2 blinks
5 blinksOff3 blinks
5 blinksOff4 blinks
5 blinksOff5 blinks
5 blinksOff6 blinks
5 blinksOff7 blinks
5 blinksOff8 blinks
5 blinksOff10 blinks
5 blinksOff11 blinks
5 blinksOff12 blinks
5 blinksOff13 blinks
5 blinksOff14 blinks
5 blinksOff15 blinks
OffOnOff
4 blinksOffOff
4 blinksOff4 blinks
6 blinksOff1 blinks
6 blinksOff2 blinks
6 blinksOff3 blinks
Red
Status & Description
Red
Power events
Lamp Ready
Start
Cooling
Case Open
DMD Error
Color Wheel Error
Lamp events
Lamp Re-Strike 6 Times Failed
Lamp Temperature Shut Down (Ballast Temp.)
Lamp Short Circuit in Output Detected (Ballast
Circuit Short)
Lamp End of Lamp Life Detected
Lamp Did Not Ignite
Lamp Extinguished During Normal Operation
Lamp Extinguished During Run-Up Phase
Lamp Voltage Too Low
Lamp Ballast Fail
Lamp Ballast COMM. fail
Lamp Ballast Over Temp.
Restrike Lamp Fail 1
Restrike Lamp Fail 2
Lamp Fail 1
Lamp Fail 2
Thermal events
Over Temperature
Thermal Break Sensor Error
G794 Error (Fan IC I2C Connection Error)
Fan 1 Error
Fan 2 Error
Fan 3 Error
49
Troubleshooting
The projector does not turn on.
CauseRemedy
There is no power from the power cord.
Attempting to turn the projector on again
during the cooling process.
No picture
CauseRemedy
The video source is not turned on or
connected correctly.
The projector is not correctly connected to
the input signal device.
The input signal has not been correctly
selected.
Blurred image
CauseRemedy
The projection lens is not correctly focused. Adjust the focus of the lens using the focus ring.
The projector and the screen are not
aligned properly.
Remote control does not work
CauseRemedy
The battery is out of power.Replace the battery with a new one.
There is an obstacle between the remote
control and the projector.
You are too far away from the projector.Stand within 8 meters (26 feet) from the projector.
The remote control code on the projector
and that on the remote control are not
consistent.
Plug the power cord into the AC inlet on the
projector, and plug the power cord into the power
outlet. If the power outlet has a switch, make sure
that it is switched on.
Wait until the cooling down process has completed.
Turn the video source on and check that the signal
cable is connected correctly.
Check the connection.
Select the correct input signal with the Source key
on the projector or remote control.
Adjust the projection angle and direction as well as
the height of the projector if necessary.
Remove the obstacle.
Adjust the remote control code.
50
Specifications
Projector specifications
• All specifications are subject to change without notice.
• Not all models can be purchased in your region.
General
Product nameDLP Projector
Optical
ResolutionPX705HD:
Display system1-CHIP DMD
Lamp240 W lamp
Electrical
Power supplyAC100–240V, 50–60 Hz (Automatic)
Power consumption330 W (Max); < 0.5 W (Standby)
Mechanical
Weight2.94 Kg (6.48 lbs)
Input terminal
Computer input
RGB inputD-Sub 15-pin (female) x 2
Video signal input
VIDEORCA jack x 1
SD/HDTV signal input
Analog – D-Sub <–> Component RCA jack x 3 (through RGB input)
Digital – HDMI V1.4a x 2
Audio signal inputAudio in jack x 1
HDMI inputx 2
Output terminal
Audio signal outputAudio jack x 1
Speaker8 watt x 1
USB Type ADC5V/1.5A
Monitor outD-Sub 15-pin (female) x 1
Control terminal
RS-232 serial control9 pin x 1
USB serial controlType mini B
IR receiverx 1 (Front)
1920 x 1080 1080p
PA505W:
1280 x 800 WXGA
51
Environmental Requirements
233.29mm (9.2")
347.66mm (13.6" )
65mm (2.56")
106.9mm (4.2")
63.50mm [2.5"]
60.00mm
[2.36"]
136.000mm [5.35"]
98.00
mm [3.85"]
98.00
mm [3.85"]
Ceiling mount screws:
M4 x 8 (Max. L = 8 mm)
Unit: mm
Operating temperature5°C–40°C at sea level
Operating relative
10%–90% (without condensation)
humidity
Operating altitude• 0–1499 m at 5°C–35°C
• 1500–3000 m at 5°C–25°C (with High Altitude Mode on)
Storage temperature-10°C to +60°C
Storage humidity10% to 85% Non-Condensing
Storage altitude30°C@ 0 to 12200m above sea level
Dimensions
347.66 mm (W) x 106.9 mm (H) x 233.29 mm (D)
Ceiling mount installation
52
Timing chart
Analog RGB
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
VGA640 x 4804:360/72/75/85
SVGA800 x 6004:360/72/75/85
XGA
WXGA
Quad-VGA1280 x 9604:360/85
SXGA1280 x 10245:460
SXGA+1400 x 10504:360
WXGA+1440 x 90016:1060
UXGA1600 x 12004:360
WSXGA+1680 x 105016:1060
HD1280 x 72016:960
MAC 13"640 x 4804:367
1024 x 7684:360/70/75/85
1152 x 8644:375
1280 x 76815:960
1280 x 80016:1060/75/85
1360 x 76816:960
MAC 16"832 x 6244:375
MAC 19"1024 x 7684:375
MAC 21"1152 x 8704:375
HDTV (1080p)1920 x 108016:960
53
HDMI
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
VGA640 x 4804:360
SVGA800 x 6004:360
XGA1024 x 7684:360
1280 x 76815:960
WXGA
Quad-VGA1280 x 9604:360
SXGA1280 x 10245:460
SXGA+1400 x 10504:360
WXGA+1440 x 90016:1060
WSXGA+1680 x 105016:1060
HDTV (1080p)1920 x 108016:950 / 60
HDTV (1080i)1920 x 108016:950 / 60
HDTV (720p)1280 x 72016:950 / 60
SDTV (480p)720 x 4804:3 / 16:960
SDTV (576p)720 x 5764:3 / 16:950
SDTV (480i)720 x 4804:3 / 16:960
SDTV (576i)720 x 5764:3 / 16:950
1280 x 80016:1060
1360 x 76816:960
54
3D (HDMI signal included)
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
SVGA800 x 6004:360* / 120**
XGA1024 x 7684:360* / 120**
HD1280 x 72016:960* / 120**
WXGA1280 x 80016:960* / 120**
HDTV (1080p)1920 x 108016:960*
for Video Signal
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
SDTV (480i)***720 x 4804:3 / 16:960
60Hz signals are supported for
*
** 120 Hz signals are supported for Frame Sequential format only.
*** Video signal (SDTV 480i) is supported for Frame Sequential format only.
Side-by-Side, Top-Bottom
, and
Frame Sequential
HDMI 3D
In Frame packing format
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
1080p1920 x 108016:923.98/24
720p1280 x 72016:950/59.94/60
In Side by side format
formats.
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
1080i1920 x 108016:950/59.94/60
In Top and Bottom format
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
1080p1920 x 108016:923.98/24
720p1280 x 72016:950/59.94/60
55
Component video
Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz)
HDTV (1080p)1920 x 108016:950 / 60
HDTV (1080i)1920 x 108016:950 / 60
HDTV (720p)1280 x 72016:950 / 60
SDTV (480p)720 x 4804:3 / 16:960
SDTV (576p)720 x 5764:3 / 16:950
SDTV (480i)720 x 4804:3 / 16:960
SDTV (576i)720 x 5764:3 / 16:950
Composite video
Signal Aspect Ratio Refresh Rate (Hz)
NTSC4:360
PAL4: 350
PAL604:360
SECAM4:350
56
Copyright information
Copyright
Copyright 2015. All rights reserved. No part of this publication may be reproduced,
transmitted, transcribed, stored in a retrieval system or translated into any language or
computer language, in any form or by any means, electronic, mechanical, magnetic, optical,
chemical, manual or otherwise, without the prior written permission of ViewSonic
Corporation.
Disclaimer
ViewSonic Corporation makes no representations or warranties, either expressed or
implied, with respect to the contents hereof and specifically disclaims any warranties,
merchantability or fitness for any particular purpose. Further, ViewSonic Corporation
reserves the right to revise this publication and to make changes from time to time in the
contents hereof without obligation to notify any person of such revision or changes.
*DLP and Digital Micromirror Device (DMD) are trademarks of Texas Instruments. Others
are copyrights of their respective companies or organizations.
57
Appendix
IR control table
Key
(with Blue back light)
Power OnNECX3F44FE8
Power OffNECX3F44EE9
COMPNECX3F441BE
VIDEONECX3F452ad
HDMINECX3F458A7
Auto syncNECX3F48F7
SourceNECX3F440BF
Up /V keystone +NECX3F40BF4
LeftNECX3F40EF1
EnterNECX3F415EA
RightNECX3F40FF0
Down/V keystone -NECX3F40CF3
MenuNECX3F430CF
InformationNECX3F49768
ExitNECX3F428D7
Aspect NECX3F413EC
FreezeNECX3F43FC
PatternNECX3F455AA
BlankNECX3F47F8
PgUp/ ID setNECX3F46F9
Volume+/ ID1NECX3F4827D
Zoom + /ID2NECX3F46798
PgDn/ ID3NECX3F45FA
Volume-/ ID4NECX3F4837C
Zoom - / ID5NECX3F46897
Eco mode/ ID6NECX3F42BD4
Mute/ ID7NECX3F414EB
Color Mode/ ID8NECX3F410EF
FormatByte1Byte2Byte3Byte4
58
RS232 command table
<Pin assignment for this two end>
PinDescriptionPinDescription
1NC2RX
3TX4NC
5GND6NC
7RTSZ8CTSZ
9NC
<Interface>
Baud Rate115200 bps (default)
Data Length8 bit
Parity CheckNone
Stop Bit1 bit
Flow ControlNone
RS-232 protocol
59
<RS232 command table>
FunctionTy peActionCommand
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x00 0x00 0x5D
0x01 0x00 0x5E
0x00 0x11 0x00 0x5E
0x02 0x00 0x5F
0x2A 0x00 0x87
0x0A 0x00 0x67
0x0A 0x01 0x68
0x0A 0x02 0x69
0x00 0x11 0x0A 0x68
0x0B 0x00 0x68
0x0B 0x01 0x69
0x00 0x11 0x0B 0x69
0x0C 0x00 0x69
0x0C 0x01 0x6A
0x00 0x11 0x0C 0x6A
0x10 0x00 0x6D
0x10 0x01 0x6E
0x10 0x02 0x6F
0x10 0x03 0x70
0x00 0x11 0x10 0x6E
Power
Reset All
Settings
Reset Color
Settings
Splash
Screen
Quick Power
Off
High Altitude
Mode
Lamp Mode
ON
Write
OFF
ReadStatus
WriteExecute
WriteExecute
Black
Write
ReadStatus
Write
ReadStatus
Write
ReadStatus
Write
ReadStatus
Blue
ViewSonic
OFF
ON
OFF
ON
Normal
Eco
Dynamic
SuperEco
60
FunctionTy peActionCommand
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x27 0x00 0x84
0x27 0x01 0x85
0x00 0x11 0x27 0x85
0x00 0x00 0x5E
0x00 0x01 0x5F
0x00 0x02 0x60
0x00 0x03 0x61
0x00 0x12 0x00 0x5F
0x20 0x00 0x7E
0x20 0x01 0x7F
0x20 0x02 0x80
0x20 0x03 0x81
0x20 0x04 0x82
0x20 0x05 0x83
0x00 0x12 0x20 0x7F
0x21 0x00 0x7F
0x21 0x01 0x80
0x00 0x12 0x21 0x80
0x02 0x00 0x60
0x02 0x01 0x61
0x00 0x12 0x02 0x61
Message
Projector
Position
3D Sync
3D Sync
Invert
Contrast
OFF
Write
ON
ReadStatus
Front Table
Rear Table
Write
Rear Ceiling
Front Ceiling
ReadStatus
OFF
Auto
Frame Sequential
Write
Frame Packing
Top Bottom
Side by Side
ReadStatus
OFF
Write
ON
ReadStatus
Decrease
Write
Increase
ReadGet Value
61
FunctionTy peActionCommand
Decrease
Write
Brightness
ReadGet Value
Write
Aspect ratio
ReadGet Value
Auto AdjustWriteExecute
Horizontal
position
Verti cal
position
Color
temperature
Write
ReadGet Value
Write
ReadGet Value
Write
ReadGet Value
Increase
Auto
4:3
16:9
Anamorphic
2.35:1
Panorama
Cycle
Shift Right
Shift Left
Shift Up
Shift Down
Warm
Normal
Cool
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x03 0x00 0x61
0x03 0x01 0x62
0x00 0x12 0x03 0x62
0x04 0x00 0x62
0x04 0x02 0x64
0x04 0x03 0x65
0x04 0x05 0x67
0x04 0x07 0x69
0x04 0x08 0x6A
0x31 0x00 0x90
0x00 0x12 0x04 0x63
0x05 0x00 0x63
0x06 0x01 0x65
0x06 0x00 0x64
0x00 0x12 0x06 0x65
0x07 0x00 0x65
0x07 0x01 0x66
0x00 0x12 0x07 0x66
0x08 0x00 0x66
0x08 0x01 0x67
0x08 0x03 0x69
0x00 0x12 0x08 0x67
62
FunctionTy peActionCommand
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x09 0x01 0x68
0x09 0x00 0x67
0x00 0x12 0x09 0x68
0x0A 0x00 0x68
0x0A 0x01 0x69
0x00 0x12 0x0A 0x69
0x0B 0x00 0x69
0x0B 0x09 0x72
0x0B 0x04 0x6D
0x0B 0x11 0x7A
0x0B 0x12 0x7B
0x33 0x00 0x92
0x0B 0x13 0x7C
0x0B 0x14 0x7D
0x00 0x12 0x0B 0x6A
0x10 0x00 0x6E
0x10 0x01 0x6F
0x10 0x02 0x70
0x10 0x03 0x71
0x10 0x04 0x72
0x10 0x05 0x73
0x00 0x12 0x10 0x6F
Blank
Keystone-
Verti cal
Color mode
Primary
Color
ON
Write
OFF
ReadStatus
Decrease
Write
Increase
ReadGet value
Brightest
Movie
Standard
Sports
Write
Gaming
Cycle
Photo
Presentation
ReadStatus
R
G
B
Write
C
M
Y
ReadStatus
63
FunctionTy peActionCommand
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x11 0x00 0x6F
0x11 0x01 0x70
0x00 0x12 0x11 0x70
0x12 0x00 0x70
0x12 0x01 0x71
0x00 0x12 0x12 0x71
0x13 0x00 0x71
0x13 0x01 0x72
0x00 0x12 0x13 0x72
0x0E 0x00 0x6C
0x0E 0x01 0x6D
0x00 0x12 0x0E 0x6D
0x00 0x01 0x60
0x00 0x00 0x5F
0x00 0x13 0x00 0x60
0x01 0x00 0x60
0x01 0x08 0x68
0x01 0x03 0x63
0x01 0x07 0x67
0x01 0x05 0x65
0x00 0x13 0x01 0x61
Hue
Saturation
Gain
Sharpness
Freeze
Source input
Decrease
Write
Increase
ReadGet value
Decrease
Write
Increase
ReadGet value
Decrease
Write
Increase
ReadGet value
Decrease
Write
Increase
ReadGet value
ON
Write
OFF
ReadStatus
D-Sub / Comp. 1
D-Sub / Comp. 2
Write
ReadStatus
HDMI 1
HDMI 2
Composite Video
64
FunctionTy peActionCommand
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x14
0x06 0x14 0x00 0x04 0x00 0x34 0x14
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x14
0x06 0x14 0x00 0x04 0x00 0x34 0x14
0x06 0x14 0x00 0x04 0x00 0x34 0x13
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x02 0x01 0x62
0x02 0x00 0x61
0x00 0x13 0x02 0x62
0x00 0x01 0x61
0x00 0x00 0x60
0x00 0x14 0x00 0x61
0x01 0x00 0x61
0x02 0x00 0x62
0x2A 0x11 0x9A
0x00 0x14 0x03 0x64
Quick Auto
Search
Mute
Volum e
ON
Write
OFF
ReadStatus
ON
Write
OFF
ReadStatus
Increse
Write
ReadGet Value
Decrese
Write Value
65
FunctionTy peActionCommand
LanguageWrite
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x00 0x00 0x61
0x00 0x01 0x62
0x00 0x02 0x63
0x00 0x03 0x64
0x00 0x04 0x65
0x00 0x05 0x66
0x00 0x06 0x67
0x00 0x07 0x68
0x00 0x08 0x69
0x00 0x09 0x6A
0x00 0x0a 0x6B
0x00 0x0b 0x6C
0x00 0x0c 0x6D
66
FunctionTy peActionCommand
Language
Lamp Hours
Reset
HDMI Format
HDMI Range
Write
Vie
ReadStatus
WriteReset to ZERO
ReadGet Usage Time
RGB
Write
ReadStatus
Write
ReadStatus
YUV
Auto
Enhanced
Normal
Auto
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x15
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x00 0x0d 0x6E
0x00 0x0e 0x6F
0x00 0x0f 0x70
0x00 0x10 0x71
0x00 0x11 0x72
0x00 0x12 0x73
0x00 0x13 0x74
0x00 0x14 0x75
0x00 0x15 0x76
0x00 0x15 0x00 0x62
0x01 0x00 0x62
0x00 0x15 0x01 0x63
0x28 0x00 0x85
0x28 0x01 0x86
0x28 0x02 0x87
0x00 0x11 0x28 0x86
0x29 0x00 0x86
0x29 0x01 0x87
0x29 0x02 0x88
0x00 0x11 0x29 0x87
67
FunctionTy peActionCommand
OFF
Write
CEC
ReadStatus
Error statusReadStatus
Write
Brilliant Color
ReadStatus
Remote
Control Code
Write
ON
OFF
Color 1
Color 2
Color 3
Color 4
Color 5
Color 6
Color 7
Color 8
Color 9
Color 10
code 1
code 2
code 3
code 4
code 5
code 6
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x06 0x14 0x00 0x04 0x00 0x34 0x12
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x0C
0x06 0x14 0x00 0x04 0x00 0x34 0x0C
0x06 0x14 0x00 0x04 0x00 0x34 0x0C
0x06 0x14 0x00 0x04 0x00 0x34 0x0C
0x06 0x14 0x00 0x04 0x00 0x34 0x0C
0x06 0x14 0x00 0x04 0x00 0x34 0x0C
0x2B 0x00 0x88
0x2B 0x01 0x89
0x00 0x11 0x2B 0x89
0x00 0x0C 0x0D 0x66
0x0F 0x00 0x6D
0x0F 0x01 0x6E
0x0F 0x02 0x6F
0x0F 0x03 0x70
0x0F 0x04 0x71
0x0F 0x05 0x72
0x0F 0x06 0x73
0x0F 0x07 0x74
0x0F 0x08 0x75
0x0F 0x09 0x76
0x0F 0x0A 0x77
0x00 0x12 0x0F 0x6E
0x48 0x00 0xA0
0x48 0x01 0xA1
0x48 0x02 0xA2
0x48 0x03 0xA3
0x48 0x04 0xA4
0x48 0x05 0xA5
68
FunctionTy peActionCommand
0x06 0x14 0x00 0x04 0x00 0x34 0x0C
0x06 0x14 0x00 0x04 0x00 0x34 0x0C
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x06 0x14 0x00 0x04 0x00 0x34 0x11
0x07 0x14 0x00 0x05 0x00 0x34 0x00
0x48 0x06 0xA6
0x48 0x07 0xA7
0x00 0x0C 0x48 0xA1
0x32 0x00 0x8F
0x32 0x01 0x90
0x32 0x02 0x91
0x32 0x03 0x92
0x00 0x11 0x32 0x90
0x33 0x00 0x90
0x33 0x01 0x91
0x33 0x02 0x92
0x33 0x03 0x93
0x33 0x04 0x94
0x33 0x05 0x95
0x00 0x11 0x33 0x91
Remote
Control code
Screen Color
Over Scan
code 7
Write
code 8
ReadStatus
OFF
Blackboard
Write
Greenboard
Whiteboard
ReadStatus
OFF
Val u e 1
Val u e 2
Write
Val u e 3
Val u e 4
Val u e 5
ReadGet Value
69
FunctionTy peActionCommand
Menu
Exit
To p
Bottom
Remote KeyWrite
AMXWriteAMX responseAMX
Left
Right
Source
Enter
Auto
0x02 0x14 0x00 0x04 0x00 0x34 0x02
0x02 0x14 0x00 0x04 0x00 0x34 0x02
0x02 0x14 0x00 0x04 0x00 0x34 0x02
0x02 0x14 0x00 0x04 0x00 0x34 0x02
0x02 0x14 0x00 0x04 0x00 0x34 0x02
0x02 0x14 0x00 0x04 0x00 0x34 0x02
0x02 0x14 0x00 0x04 0x00 0x34 0x02
0x02 0x14 0x00 0x04 0x00 0x34 0x02
0x02 0x14 0x00 0x04 0x00 0x34 0x02
0x04 0x0F 0x61
0x04 0x13 0x65
0x04 0x0B 0x5D
0x04 0x0C 0x5E
0x04 0x0D 0x5F
0x04 0x0E 0x60
0x04 0x04 0x56
0x04 0x15 0x67
0x04 0x08 0x5A
70
Customer Support
For technical support or product service, see the table below or contact your reseller.
ViewSonic warrants its products to be free from defects in material and
workmanship, under normal use, during the warranty period. If a product proves to
be defective in material or workmanship during the warranty period, ViewSonic will,
at its sole option, repair or replace the product with a like product. Replacement
product or parts may include remanufactured or refurbished parts or components.
Limited Three (3) year General Warranty
Subject to the more limited one (1) year warranty set out below, North and South
America: Three (3) years warranty for all parts excluding the lamp, three (3) years
for labor, and one (1) year for the original lamp from the date of the rst consumer
purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
ofce for the warranty information.
Limited One (1) year Heavy Usage Warranty:
Under heavy usage settings, where a projector’s use includes more than fourteen
(14) hours average daily usage, North and South America: One (1) year warranty
for all parts excluding the lamp, one (1) year for labor, and ninety (90) days for the
original lamp from the date of the rst consumer purchase; Europe: One (1) year
warranty for all parts excluding the lamp, one (1) year for labor, and ninety (90) days
for the original lamp from the date of the rst consumer purchase.
Other regions or countries: Please check with your local dealer or local ViewSonic
ofce for the warranty information.
Lamp warranty subject to terms and conditions, verication and approval. Applies to
manufacturer’s installed lamp only. All accessory lamps purchased separately are
warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the rst consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modied or removed.
2. Damage, deterioration, failure, or malfunction resulting from:
a. Accident, abuse, misuse, neglect, re, water, lightning, or other acts of nature,
improper maintenance, unauthorized product modication, or failure to follow
instructions supplied with the product.
b. Operation outside of product specications.
c. Operation of the product for other than the normal intended use or not under
normal conditions.
d. Repair or attempted repair by anyone not authorized by ViewSonic.
e. Any damage of the product due to shipment.
f. Removal or installation of the product.
g. Causes external to the product, such as electric power uctuations or failure.
h. Use of supplies or parts not meeting ViewSonic’s specications.
i. Normal wear and tear.
j. Any other cause which does not relate to a product defect.
3. Removal, installation, and set-up service charges.
72
How to get service:
1. For information about receiving service under warranty, contact ViewSonic
Customer Support (please refer to “Customer Support” page). You will need to
provide your product’s serial number.
2. To obtain warranted service, you will be required to provide (a) the original dated
sales slip, (b) your name, (c) your address, (d) a description of the problem, and
(e) the serial number of the product.
3. Take or ship the product freight prepaid in the original container to an authorized
ViewSonic service center or ViewSonic.
4. For additional information or the name of the nearest ViewSonic service center,
contact ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description
contained herein including the implied warranty of merchantability and tness for a
particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product.
ViewSonic shall not be liable for:
1. Damage to other property caused by any defects in the product, damages based
upon inconvenience, loss of use of the product, loss of time, loss of prots, loss of
business opportunity, loss of goodwill, interference with business relationships, or
other commercial loss, even if advised of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
Effect of local law:
This warranty gives you specic legal rights, and you may also have other rights
which vary from local authority. Some local governances do not allow limitations on
implied warranties and/or do not allow the exclusion of incidental or consequential
damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on ViewSonic products sold outside of the
U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and
Taiwan Excluded) is subject to the terms and conditions of the Maintenance
Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in
www.viewsoniceurope.com under Support/Warranty Information.
Projector Warranty Term Template In UG
VSC_TEMP_2005
73
Mexico Limited Warranty
ViewSonic® Projector
What the warranty covers:
ViewSonic warrants its products to be free from defects in material and workmanship, under normal
use, during the warranty period. If a product proves to be defective in material or workmanship during
the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product.
Replacement product or parts may include remanufactured or refurbished parts or components &
accessories.
How long the warranty is effective:
3 years for all parts excluding the lamp, 3 years for labor, 1 year for the original lamp from the date of
the rst consumer purchase.
Lamp warranty subject to terms and conditions, verication and approval. Applies to manufacturer’s
installed lamp only.
All accessory lamps purchased separately are warranted for 90 days.
Who the warranty protects:
This warranty is valid only for the rst consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modied or removed.
2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, re, water, lightning, or other acts of nature, unauthorized product
modication, unauthorized attempted repair, or failure to follow instructions supplied with the
product.
b. Any damage of the product due to shipment.
c. Causes external to the product, such as electrical power uctuations or failure.
d. Use of supplies or parts not meeting ViewSonic’s specications.
e. Normal wear and tear.
f. Any other cause which does not relate to a product defect.
3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.
4. Removal, installation, insurance, and set-up service charges.
How to get service:
For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to the attached Customer Support page). You will need to provide your product’s serial number,
so please record the product information in the space provided below on your purchase for your future
use. Please retain your receipt of proof of purchase to support your warranty claim.
For Your Records
Product Name: ________________________ Model Number: ____________________________
Document Number: ____________________ Serial Number: ____________________________
Purchase Date: ________________________ Extended Warranty Purchase? _____________(Y/N)
If so, what date does warranty expire? __________
1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.
2. Take or ship the product in the original container packaging to an authorized ViewSonic service
center.
3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.
Limitation of implied warranties:
There are no warranties, express or implied, which extend beyond the description contained herein
including the implied warranty of merchantability and tness for a particular purpose.
Exclusion of damages:
ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not
be liable for:
1. Damage to other property caused by any defects in the product, damages based upon
inconvenience, loss of use of the product, loss of time, loss of prots, loss of business opportunity,
loss of goodwill, interference with business relationships, or other commercial loss, even if advised
of the possibility of such damages.
2. Any other damages, whether incidental, consequential or otherwise.
3. Any claim against the customer by any other party.
4. Repair or attempted repair by anyone not authorized by ViewSonic.
74
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:
Name, address, of manufacturer and importers:
México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm
NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004
Hermosillo:
Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: 01-66-22-14-9005
E-Mail: disc2@hmo.megared.net.mx
Puebla, Pue. (Matriz):
RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: 01(52).222.891.55.77 CON 10 LINEAS
E-Mail: datos@puebla.megared.net.mx
Chihuahua
Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: 4136954
E-Mail: Cefeo@soluglobales.com
Distrito Federal:
QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: 01(52)55-50-00-27-35
E-Mail : gacosta@qplus.com.mx
CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: 01-22-91-00-31-67
E-Mail: gacosta@qplus.com.mx
Cuernavaca
Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: 01 777 3180579 / 01 777 3124014
E-Mail: aquevedo@compusupportcva.com