ViewSonic makes no representations or war r ant ies, either expressed or impl ied, with respect to the contents
hereof and specifically disclaims any warranty of merchantability or fitness for any particular purpose. Further,
ViewSonic reserves the right to revise this publication and to make changes from time to time in the contents
hereof without obligation of ViewSonic to notify any person of such revision or changes.
Trademarks
Optiquest is a registered trademark of ViewSonic Corporation.
ViewSonic is a registered trademark of ViewSonic Corporation.
All other trademarks used within this document are the property of their respective owners.
Revision History
Revision SM Editing Date ECR Number Description of Changes Editor
1a 10/24/06 Initial Release Sophia Kao
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
i
Page 3
TABLE OF CONTENTS
1. Precautions and Safety Notices.................................................................1
10. Exploded Diagram And Exploded Parts List...........................................85
11. Recommend Spare Parts List...................................................................88
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
ii
Page 4
1. Precautions and Safety Notices
1. Appropriate Operation
(1) Turn off the product before cleaning.
(2) Use only a dry soft cloth when cleaning the LCD panel surface.
(3) Use a soft cloth soaked with mild detergent to clean the display housing.
(4) Disconnect the power plug from AC outlet if the product is not used for a long period of
time.
(5) If smoke, abnormal noise, or strange odor is present, immediately switch the LCD display
off.
(6) Do not touch the LCD panel surface with sharp or hard objects.
(7) Do not place heavy objects on the LCD display, video cable, or power cord.
(8) Do not use abrasive cleaners, waxes or solvents for your cleaning.
(9) Do not operate the product under the following conditions:
- Extremely hot, cold or humid environment.
- Areas susceptible to excessive dust and dirt.
- Near any appliance generating a strong magnetic field.
- Place in direct sunlight.
2. Caution
No modification of any circuit should be attempted. Service work should only be performed after
you are thoroughly familiar with all of the following safety checks and servicing guidelines.
3. Safety Check
Care should be taken while servicing this LCD display. Because of the high voltage used in the
inverter circuit, the voltage is exposed in such areas as the associated transformer circuits.
4. Power Supply Requirements
The external AC power operating range shall be from 90 to 264Vac
5. LCD Module Handling Precautions
5.1. Handling Precautions
(1) Since front polarizer is easily damaged, pay attention not to scratch it.
(2) Be sure to turn off power supply when inserting or disconnecting from input connector.
(3) Wipe off water drop immediately. Long contact with water may cause discoloration or
spots.
(4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
(5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard
surface.
(6) Since CMOS LSI is used in this module, take care of static electricity and insure human
earth when handling.
(7) Do not open nor modify the Module Assembly.
(8) Do not press the reflector sheet at the back of the module to any directions.
(9) In case if a Module has to be put back into the packing container slot after once it was
taken out from the container, do not press the center of the CCFL Reflector edge.
Instead, press at the far ends of the CFL Reflector edge softly. Otherwise the TFT
Module may be damaged.
(10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor
tilt the Interface Connector of the TFT Module.
(11) After installation of the TFT Module into an enclosure (LCD monitor housing, for
example), do not twist nor bend the TFT Module even momentary. At designing the
enclosure, it should be taken into consideration that no bending/twisting forces are
applied to the TFT Module from outside. Otherwise the TFT Module may be damaged.
(12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please
follow local ordinances or regulations for disposal.
(13) Small amount of materials having no flammability grade is used in the LCD module.
The LCD module should be supplied by power complied with requirements of Limited
Power Source (IEC60950 or UL1950), or be applied exemption.
(14) The LCD module is designed so that the CFL in it is supplied by Limited Current
1
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
Page 5
Circuit (IEC60950 or UL1950). Do not connect the CFL in Hazardous Voltage Circuit.
5.2. Handling and Placing Methods
Correct Methods: Incorrect Methods:
Only touch the metal frame of the LCD panel
or the front cover of the monitor. Do not touch
the surface of the polarizer.
Take out the monitor with cushions Taking out the monitor by grasping the LCD
Surface of the LCD panel is pressed by fingers
and that may cause “Mura”
panel. That may cause “Mura”
2
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
Page 6
Place the monitor on a clean and soft foam pad. Placing the monitor on foreign objects. That
could scratch the surface of the panel or cause
“Mura”
3
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
Page 7
2. Specification
Note: Panel performance characteristics “ MUST BE” met in all display modes/inputs at
standard test conditions.
1. RF Tuner
RF Tuning Range
RF Tuner Sensitivity (S/N Ratio at un-weight) 44 dB (min.)
Channel Bandwidth NTSC & ATSC: 8 MHz Max
CVBS Characteristics:
Video Amplitude Signal
DC Level Sync Pulse
Audio Characteristics:
AF Output Level Measured via LP 20 kHz
Filter, RMS Decoder,
75us De-emphasis
THD
S/N
Parameter Specification
LCD Type
LCD Interface 1-Channel LVDS
Resolution (Native) WXGA, 1366 x 768
Display Area 37” diagonal; 819.6 (H) x 460.8 (V) mm
Pixel Pitch 0.6 (H) x 0.6 (V) mm
Viewing Angle
Contrast Ratio 1000:1 (Typ); 800:1 (Min)
Brightness 500 nits (Typical), 450 nits(Min.);
Response Time
Response Time (Gray to
Gray)
Colors 16.7M (8-bit)
Surface Treatment Anti-Glare, 2H
Colors 16.7M (8-bit)
Surface Treatment Hard coating (3H)
Backlight 16 CCFLs
Preset Color Panel Default
Gray Scale 255
Rated Life (Backlight) > 50 KHrs* (Typ)
Front Screen Artifacts
Panel Acceptance Spec
RF tuner of this product shall be provided by “T Vision” TVF85P3-CF.
The following table defines this tuner specification.
Parameter Specification
a-Si TFT Active Matrix Wide Color, Transmissive Mode, Normally
Black
H = +/- 85°, V = +/- 85° with CR≥20
TrR:10ms, TrD:6ms (Typ)
TrR:17ms, TrD:10 ms (max)
8 ms (Typ), 10 ms(max)
VS Standard:
a.) No Visible Streaking, Sag or Smearing artifacts when driven by
the specified video cards (see 7.1 General Test Equipment) in the
primary mode (VGA & 60 Hz) and after user adjustment
b.) No image drift or lose fine-tune settings due to panel temperature
change.
Refer to the panel acceptance criteria specification.
Note: Intermittent and/or Display Pattern defects which result in
further bright or dark dots will be counted individually against the
above specification.
NTSC & ATSC: 44.25 MHz to 863.25 MHz
covering for
0.7(min.)–1(max.) V
Typical. 0.35 V
Typical. 0.35Vrms
10% (max.)
44 dB (min.)
4
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
Page 8
2. Video
Built-in A/D converter shall provide analog to digital converter for this product.
Input Parameter Specification
CVBS Characteristics:
Video Amplitude Signal
DC Level Sync Pulse
S-Video Characteristics:
Video Amplitude Signal
DC Level Sync Pulse
Y, Pb, Pr Characteristics:
Video Amplitude Signal
DC Level Sync Pulse
0.7(min.) – 1.1(max.) V
Typical. 0.3 V
Y : 1.0Vp-p W / Neg. Sync (IN 75 Ω )
C : 0.285Vp-p (IN 75 Ω )
Y:1.0Vp-p (IN 75 Ω)
Pb:0.7 Vp-p(IN 75 Ω),Pr:0.7 Vp-p (IN 75 Ω)
Video Bandwidth NTSC/ATSC: 6 MHz Maximum
HDMI Characteristics Panel Link T.M.D.S HDMI-1.1
RGB Characteristics:
Signal Type
Sync Type
Input Signal Rating
Sync Level:
Frequency Range
Pixel Color
DDC Compliance
EDID Data Table
Analog VGA
TTL, Separate Sync, with 4.7KΩ pull-down resistors
1250Mv Max without damage to the product, 0-700 Mv Full
Range
2.5-5.25 V
Horizontal: 30-80K Hz, Vertical: 50-75 Hz
16 M
DDC2B Compliant, Rev 1.3
See Appendix B
3. Audio
Audio amp of this product shall be provided by “ESMT” with a Model Number of 8256A “MTK”
MT8202 for N3752W shall be used as sound processor. In addition, a pair of speakers shall be
integrated within this product. The audio signals of this product shall comply with the specification
listed in the following table.
Parameter Specification
Phone Jack out
Tuner Input Base band Input
Speaker Power Output Max
Rating
Speaker Impedance
Line In Per Tuner Spec
Line Out
Flatness of Amplitude Response
(100Hz ~ 10KHz)
Total Harmonic Distortion
(1KHz @1W)
Signal to Noise (1KHz @1W) 30 dB (40Hz to 15KHz) 40dB(400Hz to 20 kHz)
10 W x 2 at 10% T.H.D
Distortion
main spk :3 Ω + 3 Ω
Treble spk :5.2 Ω
10W x 2 at 10% T.H.D.
Distortion
main spk :3 Ω + 3 Ω
Treble spk :5.2 Ω
500 mV rms (Typ)
1.6 V rms (Max)
Impedance: 600 ohms
500 mVrms +/- 10%
@1K Hz tone (with +/-25k Hz
deviation at input, volume
with non-attenuation and
loading with 47k Ohm)
500 mVrms +/- 10%
@1K Hz tone (with +/-25k Hz
deviation at input, volume
with non-attenuation and
loading with 47k Ohm)
+/- 3 db (at 1KHz @1W) +/- 3 db (at 1KHz @1W)
2% 2%
5
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
Page 9
4. Electrical
The following table defines the electrical specification of this product.
ELECTRICAL SPECIFICATION
Power Input Voltage Range 100-240VAC +/- 10% Wide Range
Input Frequency Range 47-63 Hz
Input Current 3.0A @ 115VAC // 1.5A @ 230VAC
Power Supply Inrush
Power Consumption: Normal Normal:200 W (Max) // Stand by: < 3.0 W
Interference with RF and Video
Electromagnetic Compatibility
Power Supply Transient Immunity
(Supply Transients and Outage)
Surge Immunity Test
Power Supply Missing Cycle Immunity
Power Supply Acoustics
Efficiency >= 80% @ full load, nominal line
Leakage Current <0.5mA @ 240VAC
Power Saving(DPMS) N/A
Recovery Time < 3 sec.
Power Factor Correction Compliant with EN61000-3-2
Max in < 150A (with fully loaded power supply) at
230Vac
Shall not result in permanent failure of power supply
(including blown fuse)
There shall be no visible interference between power
supply, RF and video signals. This applies to all available
RF channels and video modes.
This product shall adhere to the compatibility and
immunity specifications in FCC.
Able to withstand an ANSI / IEEE C62.41 – 1980 2000V
ring wave with no damage.
Able to withstand 1.25X nominal Line Voltage for one
cycle with no damage.
Function properly without reset or visible screen artifact
when 1/3 cycle of AC Power is randomly missing.
Power supply shall not produce any audible noise during
startup and normal operation. Audible shall define to be
in compliance with ISO 7779 (DIN EN27779: 1991) .
Power Switch noise shall be Excluded.
5. Firmware & OSD
The product firmware of VS11405-1M shall have a firmware version of 1.00 Any
changes/revisions afterward shall also be pre-approved by ViewSonic in written. For VS11405-1M,
its firmware shall have a built-in frequency table for PAL/SECAM, Teletext and with NICAM
implementation.
All audio/video and other output adjustments shall be performed by using an On Screen Display
(OSD) via a Remote Control Unit (RCU) in conjunction with the front panel adjustments. The
following tables list the OSD functions supported by VS11405-1M.
OSD Table for
OSD
Brightness Adjust the Black levels
Contrast Adjust the White levels
Sharpness Adjust the Sharpness levels
Color Adjust the Color levels
Tint Adjust the Tint levels
Color Temperature Selections on Normal, Warm, user, Cold
Back Light Adjust the Back Light levels
Aspect ratio Selections the Image Size on Full, Wide1, Wide2, Wide3, 4:3, 16:9, No
Language Selections English, Spanish , French
OSD Timeout Set OSD disappearing time
Memory recall Set user settings to factory preset value
Treble Adjust the Hi Frequency levels
Bass Adjust the Low Frequency levels
VS11405
scale, Normal
By area have some difference
6
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
Page 10
Balance Adjust the Spk output levels
Audio out Audio signal output On or Off
Surround Surround sound effect On or Off
Auto Scan TV program Auto Search
Tuner Mode Selections TV sources to Air or Cable
Channel Edit TV channel name edit
Channel Add/Del. TV channel Add or Delete
Parental TV program controlled by parents via password setting
0 ~ 9, -100/ number Input channel number
Recall Return to previous channel
Guide Show electronic program guide (EPG)
Sleep* Set timer to turn off TV
CC Close caption
Mute Mute On or Off
VOL▲and VOL▼ Adjust volume
MTS/SAP Select Mono,Stereo or SAP sound
Power Power on/off
Device buttons Select desire device
Zoom Adjust window size
Wide* Change aspect ratio
Up/Down/Left/Right/
Enter
Menu On screen display (OSD) menu ON/OFF
CH▲and CH▼Change channel for TV only
Control buttons Play/Stop/Pause/Record/Forward/Rewind
Display Display current information
6. Remote Control Unit (RCU)
An IR remote control unit shall accompany this product along with battery. In addition, this
remote control unit shall have an operational distance of X meters and an operational angle of XX
degrees for both horizontal and vertical.
Parameter Specification
Range
Life Testing
(Buttons)
Color
Direct distance: 6M-12M
Point distance: 4M-8M, angle : 30 degrees +/- 2 degrees
100,000 cycle operations at a rate of 20~30 cycle / minute without load (with
battery)
Painting Color – Silver DongBon painting MP1075-01
Power Key - Red Color (Pantone 032U)
Key Pads – Refer to standard
Texts Printed on Key Pads – White Color (Refer to standard)
For the shortcut keys of Teletext:
Red Key – Pantone 185U
Blue Key – Pantone 285U
Green Key – Pantone 335U
Yellow Key – Pantone 108U
Up/Down for OSD function select and Left/Right for function adjust
Enter:Enter the function setting
▌▌buttun=freeze picture
7
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
Page 11
7. Mechanical
The following table defines the mechanical specifications of this product for both chassis and
cabinet.
Parameter Specification
Dimension W=942mm, H=726mm and D=295mm
Net Weight 26.5 Kg
Gross Weight 31.4 Kg
Net weight *without* stand 22.7 Kg
Chassis Plastic Material ABS (CABS HB / ABS VO / PC+ABS)
External Plastic Chassis
Components
Exterior Chassis
Plastic Chassis, Cover, Stand (Metal + Plastic), Len and
Button
Refer to Figure 1 – Product ID
Color/Texture/Details
Chassis Component’s Color
Refer to Figure 1A – Color Guide
Difference
Chassis Color Drift Due to
UV-Light
The color drift due to UL-Light shall be less than 10 “Delta
E” in the 1976 CIE L*a*b color space. Testing shall be
performed according to the requirements of ASTM Test
Method D4459-93.
Molded Plastic Workmanship shall be inspected according to ViewSonic
Molded Plastic Parts Specification, VSCMPPSPEC001V1.2.
Screen Printed Parts, Bird Logo
Artwork shall be provided and confirmed by ViewSonic.
Recess
Rear Label A label identifying the product name, model/serial number
and FCC ID/Logo shall be placed into the rear label recess
located on the rear panel of the chassis.
Wall- Mount 400mmx200mm VESA high hole (n=6),pattren 6mm,1.0
pitch x 10mm long screw mounting kit not imcluded.
(Figure 7)
Sample Sample of textured color chips, plastic material specification,
and Material Safety Data Sheets shall be submitted to
ViewSonic prior to Mass Production Release.
In addition, all exterior surfaces shall have uniform texture/color. The maximum acceptable
gap between the buckets to bezel plastic pieces shall be within 1.0 mm. The maximum
acceptable gap between LCD panel and bezel shall be within 2.5 mm.
8. Environmental
Operating Temperature
0°C to 40°C
Humidity 85% non-condensing
Storage Temperature Follow Panel spec
Humidity 85% non-condensing
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
8
Page 12
3. Front Panel Function Control Description
Front View of the Product
ENGLISH
Volume Down
Decrease sound volume or adjust a highlighted control while in OSD menu.
Volume Up
Increase sound volume or adjust a highlighted control while in OSD menu.
Menu
urn OSD menu ON/OFF.
T
CH Down
hannel down when source is at TV or select a control while in OSD menu.
C
CH Up
Channel up when source is at
ENTER
o highlight a control in OSD menu.
T
Power ON/OFF button
Power LED Indicator / Remote Control Receiver
Manufactured under license from Dolby Laboratories.
Dolby and the double-D symbol are trademarks of Dolby
Laboratories.
(Only for DTV source in this model.)
Note:
1. Press VOL+ and MENU buttons at the same time to lock power button, and pressVOL+ and MENU buttons again to unlock it.
2. Press VOL- and VOL+ buttons at the same time to lock OSD menu, and press
VOL- and VOL+ buttons again to unlock it.
TV or select a control while in OSD menu.
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
9
Page 13
Rear View of the Product
Power (AC input)
Using power cord provided, connect to a power source.
Air TV input
Connect to NTSC or ATSC TV source.
Cable TV input
Connect to Cable TV (CATV) or Digital Cable.
SPDIF Optical output
Connect this port to the SPDIF input of A/V device.
HDMI Input Terminal -3
Connect this port to the HDMI output of A/V device.
HDMI Input Terminal -2
Connect this port to the HDMI output of A/V device.
HDMI Input Terminal -1
Connect this port to the HDMI output of A/V device.
VGA signal input
Connect this port to the VGA output of your PC.
Composite Video input
Connect this port to the composite video output of A/V device.
YPbPr signal input
Connect this port to the YPbPr output of A/V device.
S-Video input
Connect this port to the S-Video output of A/V device.
YPbPr signal Audio input (left/right)
Connect this port to the RCA audio output connectors of your A/V device.
AV/ S-Video signal Audio input (left/right)
Connect this port to the RCA audio output connectors of your A/V device.
Audio output
Connect this port to your A/V device with audio in (RCA) connectors or to audio amplifier.
PC Audio input
Connect this port to PC line out jack.
Headphone Jack
Connect this port to your headphone.
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
10
Page 14
Remote Control
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
• Sharpness: To adjust picture sharpness. (right: sharper, left: softer).
*Note: To adjust the above controls in the Video settings, Smart Picture Mode must be set to “User”.
• Smart Picture Mode: To select picture mode between User, Cinema, Sport, Vivid, and Hi-Bright.
Audio Menu — To set the audio quality and status
Audio Menu is active in all input sources.
• Bass: To adjust bass.
• Treble: To adjust the treble
• Balance: To adjust left and right audio balance.
• Surround: To enjoy a concert hall effect, select On when stereo is playing.
• Audio Out: To control sound output ON/OFF from the RCA audio out connectors.
• Digital Audio Out: To select the sound format of the digital TV.
• Digital Audio Language: To select the audio language of the digital TV.
*Note: To adjust the above controls in the Audio settings, Smart Sound Mode must be set to “User”.
• Smart Sound Mode: To select sound mode between User, Rock, POP, Live, Dance, Techno,
Classic, and Soft.
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
13
Page 17
Setup Menu — To set up OSD window
Setup Menu is active in all input sources.
(However, when in VGA input source, there is no “V-Chip” function in the menu.)
• Language: To select an OSD language from English, French or Spanish.
• Parental: To set up parental control.
When you enter this control, the screen below will be displayed.
ENGLISH
The factory default of the password is “0000”.
To enable parental control, input the password, press ▼ button to focus on OK key, and
then press
After entering, the following screen will be shown.
Channel Lock: To lock channels. Use ◄► to select the channel you want to lock, and then
press ENTER to lock or unlock it.
Change Password: To change the password, press ENTER and enter the password again.
Press ENTER, and the following screen appears.
ENTER. (Select Cancel if you want to exit.)
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
14
Page 18
ENGLISH
Enter the new password, use ▼ to move the cursor down, and then enter the new password
again, press OK to confirm or Cancel to exit.
*Note: Please make sure you remember your new password after changing. If the password
is forgotten or missing, please use the remote control to enter “8866” to clean the password
and reset a new one.
Clear All: To clear all the locks set before, press
ENTER.
Press MENU to return to the previous page.
• V-Chip: Press ENTER, and the following screen appears.
V-Chip is transmitted from TV station to help parents monitor what their children watch.
According to the pre-set of factory, viewers can see all of the channels. However, setting
V-Chip can block the appointed channels.
The factory default of the password is “0000”.
To enable parental control, input the password, press ▼ button to focus on OK key, and
then press
ENTER. (Select Cancel if you want to exit.)
After entering, the following screen will be shown.
Use ▲▼ to select your desired optional item, and press ENTER.
• Block MPAA Rating: To adjust movie blocking level in the US. You can select between NONE, G, PG, PG-13, R, NC-17, or X.
The movie Ratings in the US are defined as following.
GGeneral audienceRRestricted
PGParental guidance suggestedNC-17 No one 17 and under limited
PG-13 Parents strongly cautionedXAdult audience only
Use ENTER button to block or unblock the ratings, and use MENU to exit.
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
15
Page 19
• Block TV Rating: To adjust TV blocking level in the US. You can select between TV-Y,
TV-Y7
, TV-G, TV-PG, TV-14, or TV-MA.
The TV Ratings in the US are defined as following.
TV-YAll childrenTV-PG Parental guidance suggested
TV-Y7 Directed to older children: this
program is designed for children
age 7 and above
TV-GGeneral audienceTV-MA Mature audience only
Use ENTER button to block or unblock the ratings, and use MENU to exit.
• Block MPAA Unrated: To block unrated movies.
• Block TV None Rating: To block unrated TV programs.
• Color Temperature: To select the color temperature from Warm, Cold, Normal or User.
(If you select User, you can adjust the degree of R, G, B in Color Temp. to suit your personal
preference.)
• Time Zone: To select Time Zones.
• OSD Timeout: To setup the display time of OSD. (5, 15, 45, and 60 seconds)
• Memory Recall: To restore the factory default settings.
TV-14Parents strongly cautioned: this
program contains some material
that is unsuitable for children under
14 years of age
ENGLISH
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
16
Page 20
ENGLISH
TV Menu — To set up for TV
It is only active in TV source.
• Tuner Mode: To select Cable or Air as the TV source. Select “Cable” if you want to watch
Cable TV channels, and select “Air” to watch Air TV channels.
• Auto Scan: To auto scan the TV and DTV channels. Press ENTER to start auto scanning TV
and DTV channels. Press ENTER again at any time to interrupt scanning.
• Channel Add/Del.: Select Delete to skip the channel appointed, or select Add to restore
the channel appointed by using ◄► or ENTER.
• Channel Name: Press ENTER to edit a name for the channel appointed. Use ▲▼◄► to
select the letters you want, and use BackSpace key to delete backwards. Move the cursor
to OK and then press ENTER to complete and save the channel name. To cancel editing,
choose Cancel or exit without pressing OK.
• Digital Closed Caption: To select closed caption signal formats and set up caption modes
for digital TV channels. (C1~C4, Service1~Service 6, or OFF)
• Digital CC Style: Press ◄► to select Caption Style from As Broadcaster or Custom.
When Custom is selected, use ▲▼ to select the desired controls, ◄► to adjust detailed
settings.
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
17
Page 21
Font Size: To select a font size from Large, Small, or Medium.
Font Style: To select different font style from Style 1 to Style 7.
Font Color: To select a font color from Black, White, Green, Blue, Red, Cyan, Yellow, or
Magenta.
Font Opacity: To select font opacity from Solid, Translucent, or Transparent.
Background Color: To select background color.
Background Opacity: To select background opacity.
Window Opacity: To select window opacity.
Window Color: To select window color.
VGA Menu — To set up for computer
It is only active in VGA source.
• Auto Adjust: Press ENTER to auto adjust picture’s horizontal position, vertical position,
fine tune and H-Size.
• Contrast: To adjust contrast of the video.
• Brightness: To adjust luminance of the video.
• Fine Tune: To adjust the delay time of data and clock to reduce noise in picture.
• Manual Clock: To adjust the horizontal pixel clock of the video.
• H. Position: To adjust the horizontal position of the picture.
• V. Position: To adjust the vertical position of the picture.
ENGLISH
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
18
Page 22
ENGLISH
ADVANCED OPERATION — REMOTE CONTROL
PIP/POP
PIP/POP button allows you to watch two screens from different sources at the same time.
(PIP is picture in picture; POP is picture out of picture.)
Press PIP on the remote control repeatedly.
The screen will change from normal screen → PIP screen → POP screen.
PIP Screen POP Screen
• PIP Input Source Select
1. Press PIP Source button to select input source for sub-screen as following.
(You must press
Main ScreenAvailable Sub-Screen Input Source
PIP button first.)
TVYPbPr / HDMI1 / HDMI2 / HDMI3 / VGA
AVYPbPr / HDMI1 / HDMI2 / HDMI3 / VGA
S-VideoYPbPr / HDMI1 / HDMI2 / HDMI3 / VGA
YPbPrTV / AV / S-Video / HDMI1 / HDMI2 / HDMI3
HDMI1 / HDMI2 / HDMI3AV / S-Video / YPbPr / VGA
VGATV / AV / HDMI1 / HDMI2 / HDMI3
2. Use ◄► to select the sub-input source and press ENTER to confirm.
Note: To select the input source for main screen, press SOURCES button.
• PIP Size Select: Press PIP Size to select the size of sub-screen. The function only acts on PIP.
• PIP Position Select: Press ▲ to select the position of sub-screen. The function only acts
on PIP.
Note that the screen indexed with the pink frame is the screen you select to set up.
Use ◄► to move the index between the main screen and the sub-screen.
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
19
Page 23
4. Circuit Description
A. Analog Switch and Vi deo input.
MT8202 is a highly integrated video and audio single chip processor for emerging
HDTV-Ready LCD TV. It includes one 3D/2D TV Decoder recovering the best image from
CVBS, and in addition, its analog input also support popular S-Video, Component, VGA video
source. On-chip advanced motion adaptive de-interlacer (MDDitm) converts accordingly the
interlace video into smooth non-flicking progressive motion pictures.
Analog switch is built in MT8202 and accept CVBS, YPbPr, S-Video, RGB signal directly to
internal video front end. For most system application, there is no need to add external
components to add analog video multiplexer on board.
The video ADC sample analog input signals. After ADC, all signal processing is digital
domain.The source select multiplex all inputs from digital and analog video ports and route
them into Main and PIP data path.
B. 3D comb filter, Video Decoder, Deinterlacer and Scaling controller.
MT8202 includes 3D comb filter TV decoder to retrieve the best image from popular
composite signals. Embedded HDTV/VGA decoders let the high bandwidth input signals
perfectly reproduced. 24/16/8 bits digital port may accept all kinds of external digital input
video source. New 2nd generation advanced motion adaptive de-interlacer converts
accordingly the interlace video into progressive one with overlay of a 2D Graphic processor.
Advanced full function color processing with fully 10-bit path provides high quality video
contents. Independent two Flexible scalers provide wide adoption to various LCD panels for
two of different video sources at the same time. MT8202 supports alpha blending for Video
and two OSD planes. It also supports 10bit gamma correction and advanced dithering
processing for LCD display with 6/8/10 bit output.
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
20
Page 24
C. DTV and HDMI.
MT5112 is a fully integrated single-chip 8-VSB and 64/256-QAM demodulator. The chip is
designed specifically for the digital terrestrial HDTV and CATV receivers
10-bit A/D converter, 8-VSB/QAM demodulator, TCM (Trellis-Coded modulation) decoder,
and Reed- Solomon Forward Error Correction decoder. Moreover, an internal controller
handles the acquisition and tracking to ensure the best receiving performance.
The internal controller communicates with the external host controller via the I2C-compatible
interface, and also provides direct control to the RF tuner via the second I2C-compatible
interface.
MT5112 accepts either the direct IF signals and the IF signals are sampled by a 10-bit A/D
converter. Afterward, the digitized samples are further processed for adjacent channel
interference rejection. MT5112 measures the power level of the digitized sequence, and feeds
the control voltages back to the RF tuner and the IF amplifier respectively. The control
voltages are converted to analog signals through the on-chip 1-bit sigma-delta D/A converters
plus the off-chip R-C low-pass filters. The automatic gain control keeps the received power
level at a desired level and maximizes the received SNR.
The MT5351AG is a DTV Backend Decoder SOC which support flexible transport demux,
HD MPEG-2 video decoder, JPEG decoder, MPEG1,2, MP3, AC3 audio decoder, HD TV
encoder. It incorporates a processor for system control. The processor issues instructions to
control the peripheral via I²C and communicates with MT8202 via UART. DDR
externally connected to the MT5351AG, the unified memory allows all internal decoders can
share data,which reduces external memory types and capacities.
The MT5351AG receives bitstream input in TS format, and then separates the TS into audio
and video PES, analyzing the PES header, and transferring the PES to the audio and video
decoders.
. MT5112 includes a
SDRAM is
MT8293 is fully HDMI-compliant receiver that fits directly into home theater products such as
LCD TVs, plasma TVs and HDTVs. The receiver is capable of supporting bandwidths up to
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
21
Page 25
165 MHz and video resolutions up to 1080p and UXGA. The MT8293 supports the
DVD-Audio standard, including 7.1- surround audio at 96kHz and stereo audio at 192kHz.
The built-in High-bandwidth Digital Content Protection (HDCP) decryption engine secures the
digital link for transmission of valuable high-definition video and audio. Built-in HDCP
MT8293 has 3 I2C interfaces.
LCD Controller IC use the CSDL/CSDA interface to access MT8293 registers.
MT8293 use KSDL/KSDA interface to read HDCP key from the EEPROM.
HDMI transmitter use DSDL/DSDA to access MT8293 HDCP related register.
HDMI Transmitter will pull high HDMI_PLUG_POWER (pin 18 in connector) when the
cable is connected. LCD Controller will pull high HDMI_HPD (pin 19 in connector) to info
the HDMI transmitter that the receiver is ready. The HDMI transmitter sends the video &
audio to MT8293 via 3 Data TMDS pairs & 1 CLOCK TMDS pairs.
Digital video signals are directly output from the MT5351AG and MT8293 and then transfer
them to the MT8202 for advanced processing.
DDR
SDRAM
DDR
SDRAM
FLASH
ATSC RF
TUNER
MT5112
(Demod.)
MT6351
(Mpegdecoder)
MT8202
HDMI
MT8293
(HDMI Bx)
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
22
Page 26
D. Audio
MT8202 incorporates a on-chip audio processor decodes whole world standard audio signals
from tuner with lip sync control, delivering high quality post-processed sound effect to
customers. Audio interface accept analog audio signal from Tuner, e.g. SIF or AF. It also
includes preprocessing circuit to filter the noisy audio signals. Audio decoder will decode the
BTSC, and output best sound with enhanced 3D surround post-processing.
The AD12250 converts stereo single-ended analog input signals into 24-bit I2S digital audio
data through on-chip anti-aliasing filter, multi-bit Σ-Δ modulator, decimation filter and
high-pass filter which removes dc offsets. External analog audio signal , such as AV, S-video,
etc. is directly fed into AD12250 via a audio switch and converted to I2S digital audio data.
Digital audio, such as HDMI and DTV, have decoded by MT5351 and MT8293, is converted
to I2S digital audio already. The I2S digital audio data is decoded and processed by MT8202,
and then be delivered to AD8256 for audio amplifying.
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
23
Page 27
5. Adjusting Procedure
1. Function Test
1.1. Product
- 37” LCD TV
1.2. Test Equipment
-PC signal generator: CHROMA 2525 CARD ,CHROMA 2327 or 2329,Pioneer
DV-S969AVi.
-TV and Video signal generator.
-Color analyzer: MINOLTA CA110.
-Power meter: CP-310A or CP-320A.
-AC power supply transformer: 110V/120V ±20% 60Hz ±5%.
-Digital ammeter
1.3. Test Condition
Before function test and alignment, each LCD TV should be run-in and warmed up for at
least 30 minutes with the following conditions:
(a) In room temperature,
(b) With full-white screen, and 16 grey scale,
(c) With cycled display modes.
1.4. Test Display Modes & Pattern
1.4.1 EEPROM INIT
A. Timing: 1360*768@60Hz
B. Pattern: 16*12 pane
C. Press ’POWER’, ‘▲’and ‘ENTER’ at the same time, then go into the FACTORY
MODE.
Fig. 1 Fig. 2
D. Figure 1,Select EEPROM INITIAL and press ENTER. The act of EEPROM
INITIAL is completed when EEPROM INIT disappeared.
1.4.2 COLOR TEMPERATURE ADJUSTING
PC MODE:
A. Timing: 1360*768@60Hz.
B. Pattern: 16 grey scale.
C. LCD TV should be run-in and warmed up for at least 30 minutes.
D. Make sure the distance between SENSOR of the CA110 and the LCD TV is about
20cm.
E. Color Temperature adjusting.
1.Fig. 1: under the picture 16 grey scale of VGA source, select WHITE
BALANCE and press ENTER, The color warm will auto adjust. The act of EHITE
BALANCEL is completed when the picture is steady.
2.After adjusting, switch to FULL WHITE and check the value of each color.
Preset color for N3752W
x=0.283±0.015 y=0.297±0.015
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
24
Page 28
3.Under the picture NTSC color bar of YPbPr source, select WHITE BALANCE
and press ENTER, The color warm will auto adjust. The act of EHITE
BALANCEL is completed when EHITE BALANCEL disappeared.
4.After adjusting, switch to FULL WHITE and check the value of each color.
Preset color for N3752W
x=0.283±0.015 y=0.297±0.015
1.4.3 Power Consumption Check ( VGA MODE )
A. TIMING: 1360 x 768@60Hz
B. Pattern: 1010UPRIGHTNESS PATTERN
C. BRIGHTNESS=MAX, CONTRAST=MAX.
D. The power that each MODE consumed is shown in Chart 1.
MODE
NORMAL
Stand-by
1.4.4 Check the position of the picture displayed and phase auto adjusting (VGA MODE).
Depend on the TIMING of TIMING TABLE (TABLE 3) to switch MODE in order,
stay about 10 seconds each MODE, it can changed and stored automatically each
MODE. We can’t switch over to the next MODE until AUTO ADJUST disappears.
1.4.5 HDMI MODE FUNCTION TEST
A.DVI MODE: Depend on the TIMING of TIMING TABLE (TABLE 3 ) to check
MODE in order.
B.HDMI MODE: make sure the 480i, 480p, 720p, 1080i TIMING is right.
1.4.6 OSD FUNCTION TEST
A. Time: 1360x768@60Hz
B. Pattern: 16*12 pane
C. Make sure that Each FUNCTION has one right action.
1.4.7 DTV FUNCTION TEST
Make sure the power is OFF before installing your LCD TV.
A. Air TV: Connect the LCD TV to TV antenna with 75-ohm coaxial cable. Preset
the air TV channels into memory with AUTO SCAN function when using an
antenna TV system. This air input jack both support TV and DTV systems.
Besides, the TV system (NTSC) and DTV systems (ATSC) can be found by the
scanning of “AIR” in the AUTO SCAN function.
B. Cable TV: Connect the LCD TV to the cable with CATV and Digital cable. Preset
the cable TV channels into memory with AUTO SCAN function when using a
cable TV system. The cable input jack both support CATV and Digital cable
systems. Besides, the CATV system (cable TV) and Digital cable system (Clear
QAM) can be found by the scanning of “Cable” in the AUTO SCAN function.
1.4.8 YPbPr, S-VIDEO, AV, TV, DTV’S FUNCTION TEST
A. Input YPbPr, S-VIDEO, AV , TV, DTV’S signal and check.
B. Input USA air channel (TABLE 1) and USA CATV channel for TV channel.
C. Under YPbPr MODE, Make sure the 408i, 480P, 720P, 1080i is right.
1.4.9 AUDIO FUNCTION TEST
A. Audio input includes PC AUDIO IN, S-VIDEO/AV AUDIO IN and YPbPr AUDIO
IN.
B. Under PC MODE, input PC AUDIO signal, checks whether the action of AUDIO IN
is right.
C. Under S-VIDEO/AV MODE, input L/R AUDIO signal, checks whether the action of
AUDIO IN is right.
D. Under YPbPr MODE, input L/R AUDIO signal, checks whether the action of AUDIO
IN is right.
E. Under HDMI MODE, checks whether the action of AUDIO IN is right.
F. Under DTV MODE, checks whether the action of SPDIF is right.
G. AUDIO OUT FUNCTION TEST: Under all patterns except PC pattern, The Audio
output meets active extra speaker, examines whether the extra speaker makes the sound.
1.4.10 EARPHONE FUNCTION TEST
Under PC MODE, input PC AUDIO signal, determines whether the action of INT
SPEAKER output is right. Meets earphone with the EARPHONE, Determined whether
MAX POWER COMSUMED POWER LED COLOR
200W(max) GREEN
3 W (max) RED
Chart 1
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
25
Page 29
the action of EARPHONE output is normal.
1.4.11 All Modes Reset
After final QC step, we must to erase all saved changes again and restore the factory
defaults.
You should do “All Mode Reset” again.
Turn off the LCD TV by pressing “Power” button.
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
27
Page 31
1.5. TV receiving test:
1.5.1 TV SIGNAL TEST ITEM
CENTRALISM TRANSMITTING SIGNAL CHECK CONTENT
CHANNEL
ORDER
CHANNEL 2
CHANNEL 6
CHANNEL 7
CHANNEL 13
CHANNEL 14
CHANNEL 36
CHANNEL 69
TV TEST METHOD
A.CHANNEL2 Examines sound by ear, whether the sound does have mechanical resonation and
the electrical unusual sound, and image to sound disturbance.
B.CHANNEL6: Check sound and picture.
C.CHANNEL7: Examines whether the sound does receive the image disturbance, Judgment basis:
Whether there is unusual sound, input signal LEVEL<=36dBu,and STEREO SENSITIVITY is
normal.
D.CHANNEL13: Under main/sub/main-sub mode, check sub function.
E.CHANNEL14: Examines whether the sound does receive the image disturbance, Judgment basis:
Whether there is unusual sound.
F. CHANNEL 36:Check T1 of close-caption. Input signal level<=45dBu.
G.CHANNEL 69: Adjustment attenuator, If the critical point of the change of the image signal to
noise ratio is under LEVEL<=60dBu, regards as normally.
PRODUCTS OUTPUT CHECK ITEM.
A. The same as " CENTRALISM TRANSMITTING SIGNAL CHECK CONTENT"
B. saturation TEST, inputs the TV signal, the input signal LEVEL establishment most greatly is
90dBu,check whether CONTRAST of the image is normal; Whether appears the disturbance
phenomenon.
C.AFT CHECK,
(1) The frequency of the input TV signal is 211.25MHz (CH13), after confirmed the TV set
receives this signal, closure radio station; Then set frequency of the TV signal generator to be
212.25MHz, turn on the TV set and check whether the TV set receives the signal of CH13.
(2). The frequency of the input TV signal is 211.25MHz (CH13), after confirmed the TV set
receives this signal, closure radio station; Then set frequency of the TV signal generator to be
211.00MHz, turn on the TV set and check whether the TV set receives the signal of CH13.
(3). After all of FUNCTION TEST completed, we must erase all saved changes again and
restore the factory defaults.
1.6. DTV TEST ITEM
CHANNEL
14
36
69
DTV CHECK METHOD
FREQUENCY
(MHz)
55.25 MONO SCOPE SWEEP TONE-10 ELECTRIC
83.25 COLOR BAR 400Hz -10 SOUND ,PICTURE
175.25 Full White (100
211.25 STAIR DUAL -10 SUB FUNCTION
471.25 MULTIBURST MONO -16 IMAGE AND SOUND
603.25 MULTIBURST MONO -10 TEST Close-caption T1
801.25 MONO SCOPE MONO(1KHz)-10 NOISE LIMMITTED
FREQUENCY SOUND dB PETTEN CHECK CONTENT
471.25MHz Y 50 Dynamic picture Picture
603.25MHz Y 50 Color bar Color
801.25MHz Y 75 Dynamic picture Sound and Picture
PATTERN SOUND P/S(dB)
SET CONTENT
STEREO -10 STERO FUNCTION
IRE)
CHECK
CONTENT
ABNORMITY SOUND
DISTURB
FUNCTION
SENSITIVITY
A.CHANNEL14: Check whether there are some pause or the mosaic phenomenon in the picture.
B.CHANNEL36: Check whether the color of the color bar is normal.
C.CHANNEL69: Turn RF attenuator and check the critical point of the change of the image’s
S/N is under LEVEL<45~85> dBu, regards as normally.
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
Power Cord USAA-00005362 2427130046PP951
Remote ControlA-00008027
Sub Board - SP271-5F01 SPIB-00006605 2200237018PU801
Main BoardB-00008055 6201-7037151101
Control BoardB-00008056 6202-7037151101
Sub Board (Darfon)B-00008058 2200237015PU801
Sub Board (IR Board) B-00008087 6206-7027146411
Power Supply Board (Lienchen)B-00008088 2200237017PU801
Back Cover (Black)C-00008082 2022265104P2C01
Front PanelC-00008119 26033081382C01
Video IO Cable D15/D15 20276(4.5) 1.83M BLACKCB-00005507 2427501195PP961
Video Cable-Cable ,D15/D15 20276(3+6) 1.83M BlackA-VC-0101-0386 2427501187PP961
User's GuideDC-00008104 2001131664P6P80
Quick Start GuideDC-00008105 2002310614P6P81
LCD Panel - (CLAA370WA02 CPT)E-00006614 2212009900PV901
Speaker 10W/60hmE-00008039
Integrated CircuitE-00008040 2365104000PI116
Bracket 2.0THW-00008018 2071882200P5B03
Box (Carton 360X220X50mm (WXDXH) Box(B)P-000044972011100017P6P85
Foam - EPE (TOP.LEFT)P-000066162012186100P6P20
Foam - EPE (TOP.RIGHT)P-000066172012186200P6P21
Foam - EPE (BOTTOM.LEFT)P-000066182012186300P6P22
Foam - EPE (BOTTOM.RIGHT)P-000066192012186400P6P23
PolybagP-000080632013054002P6P60
Craft BoxP-000081022011137020P6P01
Pedestal (Stand)PL-00008027 2028260602P5B01
ge covers]
Remark 1: Above listed items are examples, supplier can expand the rows to add more necessary items.
All revised RSPLs with newly added items or any change made should be highlighted and correlated with the ECN/ECR approved by ViewSonic Corporation. This is
Remark 2:
Description
2419200105PH901
2391310062PW901
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
88
Page 92
ViewSonic Model Number: VS11405Rev: 1a
Serial No. Prefix: QFU
ItemViewSonic P/NRef. P/N
1 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC1041
2 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1071
3 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1091
4 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1121
5 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1141
6 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1161
7 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1231
8 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1261
9 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1291
10 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1331
11 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1341
12 E-C-0404-44232341122096P CAP,CHIP 125'CCS 0603/COG/50V 22p J TC1351
13 N/A2341127096P CAP,CHIP 125'CCS 0603/COG/50V 27p J TC1361
14 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1371
15 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC1381
16 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC1951
17 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC2031
18 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC2111
19 N/A2347647596P CAP,CHIP 85'CCS 0805/Y5V/16V 4.7u Z TC2131
20 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC2151
21 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC2231
22 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC2281
23 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC2311
24 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC2391
25 N/A2347710696P CAP,CHIP 85'CCS 0805/Y5V/10V 10u Z TC2431
26 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC2451
27 N/A2347710696P CAP,CHIP 85'CCS 0805/Y5V/10V 10u Z TC2481
28 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC2491
29 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC2501
30 N/A2347710696P CAP,CHIP 85'CCS 0805/Y5V/10V 10u Z TC2511
31 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC2531
32 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC2571
33 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC2651
34 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC2721
35 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC2751
36 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC2821
37 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC2861
38 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC2871
39 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC3041
40 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC3051
41 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC3061
42 N/A2341147196P CAP,CHIP 125'CCS 0603/COG/50V 470p J TC3091
43 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC3101
44 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC3181
45 N/A2346147396P CAP,CHIP 125'CCS 0603/X7R/50V 0.047u K TC3311
46 N/A2346147296P CAP,CHIP 125'CCS 0603/X7R/50V 4700p K TC3321
47 N/A2341133196P CAP,CHIP 125'CCS 0603/COG/50V 330p J TC3331
48 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC3341
49 N/A2346147396P CAP,CHIP 125'CCS 0603/X7R/50V 0.047u K TC3351
50 N/A2341115096P CAP,CHIP 125'CCS 0603/COG/50V 15p J TC3361
51 N/A2341133196P CAP,CHIP 125'CCS 0603/COG/50V 330p J TC3371
52 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC3381
53 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC3391
54 N/A2346147396P CAP,CHIP 125'CCS 0603/X7R/50V 0.047u K TC3401
55 N/A2341115096P CAP,CHIP 125'CCS 0603/COG/50V 15p J TC3411
56 N/A2341133196P CAP,CHIP 125'CCS 0603/COG/50V 330p J TC3421
57 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC3431
58 N/A2346147396P CAP,CHIP 125'CCS 0603/X7R/50V 0.047u K TC3441
59 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC3451
60 N/A2341133196P CAP,CHIP 125'CCS 0603/COG/50V 330p J TC3461
61 N/A2341115096P CAP,CHIP 125'CCS 0603/COG/50V 15p J TC3471
62 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC3481
63 N/A2341156096P CAP,CHIP 125'CCS 0603/COG/50V 56p J TC3491
64 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC3541
65 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC3551
66 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC3561
67 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC3571
68 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC3641
69 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC3781
70 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC4011
71 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4101
72 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4161
73 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4191
74 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4201
1M
Description
Location
Universal number# Q'ty
BOM LIST (N3752w-1M)
ViewSonic Corporation Confidential - Do Not Copy N3752w-1M
89
Page 93
ItemViewSonic P/NRef. P/N
y
75 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4261
76 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4291
77 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4301
78 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4321
79 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4391
80 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4401
81 N/A2341110296P CAP,CHIP 125'CCS 0603/COG/50V 1000p J TC4461
82 N/A2341110296P CAP,CHIP 125'CCS 0603/COG/50V 1000p J TC4471
83 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC4511
84 N/A2346710596P CAP,CHIP 85'CCS 0603/Y5V/16V 1.0u Z TC4911
85 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC5501
86 E-C-0404-38982341110096P CAP,CHIP 125'CCS 0603/COG/50V 10 p J TC5511
87 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC5531
88 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC5541
89 N/A2341110296P CAP,CHIP 125'CCS 0603/COG/50V 1000p J TC5551
90 N/A2341147096P CAP,CHIP 125'CCS 0603/COG/50V 47p J TC5561
91 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC5851
92 N/A2346110496P CAP,CHIP 125'CCS 0603/X7R/50V 0.1u K TC5881
93 N/A2347647596P CAP,CHIP 85'CCS 0805/Y5V/16V 4.7u Z TC5991
94 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC6081
95 N/A2341150996P CAP,CHIP 125'CCS 0603/COG/50V 5.0 p D TC6091
96 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC6101
97 N/A2346147296P CAP,CHIP 125'CCS 0603/X7R/50V 4700p K TC6111
98 N/A2346110396P CAP,CHIP 125'CCS 0603/X7R/50V 0.01u K TC6121
99 N/A2341150996P CAP,CHIP 125'CCS 0603/COG/50V 5.0 p D TC6131