Page 1
E90fmb Color Monitor
User Guide
Guide de l’utilisateur
Guía del usuario
Guia do usuário
With Plug & Play
19" (18" Viewable Diagonal)
&
Page 2
Contents
Product Registration..............................................................2
For Your Records ..................................................................2
Getting Started
Package Contents .................................................................3
Precautions ...........................................................................3
Quick Installation ...................................................................4
Using the Monitor
Setting the Timing Mode .......................................................5
Adjusting the Screen Image ..................................................6
Main Menu Controls ..............................................................8
Other Information
Specifications ......................................................................11
Troubleshooting...................................................................12
Customer Support ...............................................................13
Cleaning the Monitor ...........................................................14
Limited Warranty .................................................................15
Appendix
Safety Guidelines ................................................................16
Compliance Information for U.S.A.......................................17
CE Conformity for Europe ...................................................17
ViewSonic E90fmb 1
Page 3
Copyright © ViewSonic Corporation, 2001. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Computer, Inc.
Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft
Corporation in the United States and other countries.
ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of
ViewSonic Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC
are trademarks of VESA.
®
E
NERGY STAR
As an E
E
NERGY STAR
NERGY STAR
Disclaimer: ViewSonic
is a registered trademark of the U.S. Environmental Protection Agency (EPA).
®
®
partner, ViewSonic Corporation has determined that this product meets the
guidelines for energy efficiency.
Corporation shall not be liable for technical or editorial errors or omissions
contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.
In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
change product specifications without notice. Information in this document may change without
notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.
Product Registration
To meet your future needs, and to receive any additional product information as it becomes available, please register your product on the Internet at:
www.viewsonic.com.
The ViewSonic
CD-ROM also provides an opportunity for you to print the registration form, which you may mail
or fax to ViewSonic.
For Your Records
Product Name:
Model Number:
Document Number:
Serial Number:
Purchase Date:
E90fmb
VCDTS23693
A-CD-E90fmb-1
_______________
_______________
Product disposal at end of product life
ViewSonic is concerned about the preservation of our environment. Please dispose of this product
properly at the end of its useful life. Your local waste disposal company may provide information
about proper disposal.
®
Wizard
2 ViewSonic E90fmb
Page 4
Getting Started
Congratulations on your purchase of a ViewSonic® color monitor. Important!
Save the original box and all packing material for future shipping needs.
NOTE:
The word “Windows” in this user guide refers to the following Microsoft
operating systems: Windows 95, Windows NT, Windows 98, Windows 2000,
Windows Me (Millennium), and Windows XP.
Package Contents
Yo ur package includes:
• Color monitor
• DB-15 video cable
• Power cord
• ViewSonic Wizard CD-ROM
NOTE:
The CD jacket contains the Quick Start Guide, and the CD includes the
User Guide PDF files and INF/ICM display optimization files. The INF file
ensures compatibility with Windows operating systems, and the ICM file (Image
Color Matching) ensures accurate on-screen colors. ViewSonic
recommends
that you install both files.
Precautions
• For best viewing conditions sit at least
18” from the monitor.
• AVOID TOUCHING THE SCREEN
WITH YOUR FINGERS. Oils from the
skin are difficult to remove.
• NEVER REMOVE THE REAR
COVER. The monitor contains high
voltage parts. You may suffer serious
injury if you touch these parts.
• Avoid exposing the monitor to direct
sunlight or another heat source,
including an open flame. The monitor
should be facing away from direct
sunlight to reduce glare.
• Always handle your monitor with care
when moving it.
• Place your monitor in a well ventilated
area. Do not place anything on the
monitor that prevents adequate
dissipation of heat.
• Ensure the area around the monitor is
clean and free of moisture.
• Keep the monitor away from magnets,
motors, transformers, speakers, and
televisions.
• Do not place heavy objects on the
monitor, video cable, or power cord.
• If smoke, abnormal noise, or strange
odor is present, immediately switch the
monitor off and call your dealer or
ViewSonic. It is dangerous to continue
using the monitor.
ViewSonic E90fmb 3
Page 5
Quick Installation
1 Connect power cord
Connect the power cord to a properly
grounded AC outlet.
2 Connect video cable
Make sure both the monitor and computer
are turned OFF.
• Connect the video cable to the computer.
Macintosh
require a Macintosh adapter. Attach the
adapter to the computer and plug the video
cable into the adapter.
To order a ViewSonic
contact ViewSonic. See “Customer Support”
on page 13.
®
users: Models older than G3
®
Macintosh adapter,
3 Connect Audio cables
Connect the microphone and speaker audio
cables to the audio card of your computer.
4 Turn ON monitor and computer
Turn ON the monitor, then turn ON the
computer. This sequence (monitor before
computer) is very important.
NOTE:
receive a message asking them to install the
INF file.
At this point Windows users may
5 Install Display Optimization files
(INF and ICM files)
(1) Insert the ViewSonic Wizard CD-ROM
into your computer’s CD-ROM drive.
NOTE:
CD-ROM drive, see “Customer Support” on
page 13.
If your computer does not have a
(Continued)
(2) Wait for the CD-ROM to auto-start.
NOTE:
double-click on the CD-ROM icon in
Windows Explorer, then double-click on
viewsonic.exe
(3) Follow the on-screen instructions.
If the CD-ROM does not auto-start:
.
6 Windows users: Set the Timing
Mode (resolution and refresh rate) Example:
1024 X 768 @ 75 Hz.
For instructions on changing the resolution
and refresh rate, see the graphic card’s user
guide.
Installation is complete. Enjoy your new
ViewSonic color monitor.
To be best prepared for any future customer
service needs: print this user guide and write
the serial number in “For Your Records” on
page 2. (See back of monitor.)
To register your product go online to
www.viewsonic.com
The ViewSonic Wizard CD-ROM also
provides an opportunity for you to print the
registration form which you may mail or fax
to ViewSonic.
.
Audio IN (from
speakers to audio
card in computer)
Microphone OUT
(to audio card in
computer)
AC wall outlet
4 ViewSonic E90fmb
VGA video cable
Power cables
Page 6
Using the Monitor
Setting the Timing Mode
Setting the timing mode is important for maximizing the quality of the
screen image and minimizing eye strain. The timing mode consists of the
resolution (example 1024 x 768) and refresh rate (or vertical frequency;
example 85 Hz). After setting the timing mode, use the OnView
to adjust the screen image.
For the best picture quality set your monitor timing mode to:
VESA 1024 x 768 @ 85 Hz.
To set the Resolution:
1
Right-click on the Windows desktop.
2
Click Properties on the drop-down menu.
3
Click the Settings tab.
4
Move the slider pointer which displays in the Desktop area or Screen area in
the window.
®
controls
NOTE: The refresh rate should already be set if you have done the CD
installation (or refer to your graphics card documentation).
ViewSonic E90fmb 5
Page 7
Adjusting the Screen Image
Use the buttons on the front control panel to display and adjust the OnView®
controls which display on the screen. The OnView controls are explained at the
top of the next page and are defined in “Main Menu Controls” on page 8.
Main Menu
With OnView controls
Front Control Panel
Displays Main Menu; also saves
changes/exits Main Menu
Mutes audio
output
Increases/decreases
audio volume
6 ViewSonic E90fmb
Scroll through menu
options and adjust the
displayed control
Power Light
Displays control screen for
highlighted control (or pair of
controls). Also, toggles
between pairs of controls on
some control screens
Power On/Off
Page 8
Do the following to adjust the screen image:
1
To display the Main Menu, press button [1].
i
2
To select a control you want to adjust, press the arrow buttons on the front
control panel of your monitor and scroll through the choices. When the
control you want is highlighted, press button [2].
NOTE: Some controls on the Main Menu are listed in pairs, such as
Contrast/Brightness. Display control screen (sample shown in step 3 below).
Press button [2] to toggle to the next control in the pair.
3
To adjust the selected control, such as
CONTRAST
in the sample below,
press the arrow buttons.
4
To save the control setting and Exit the menu press button [1] twice.
ViewSonic E90fmb 7
Page 9
Main Menu Controls
Adjust the menu items shown below by using the up Iand down Jbuttons.
Control Explanation
Contrast
adjusts the difference between the image
background (black level) and the foreground (white level).
Brightness
adjusts the background black level of the screen
image.
Horizontal Size
Horizontal Position
Vertical Size
Vertical Position
Zoom
expands and contracts the entire screen image.
adjusts width of the screen image.
moves the screen image left or right.
adjusts the height of the screen image.
moves the screen image up or down.
Pincushion
Pin Balance
the left or right.
Trapezoid
until they have equal length.
Parallelogram
until they are parallel.
Rotation
8 ViewSonic E90fmb
curves the vertical sides of the screen image.
curves the vertical edges of the screen image to
adjusts the top and bottom of the screen image
slants the vertical edges of the screen image
rotates the entire screen image.
Page 10
Control Explanation
Degauss
removes the build-up of magnetic fields that can
cause irregular colors to appear around the edges of screen
images. There are two ways to degauss the display:
automatically by turning the monitor on, or manually by
selecting the Degauss control from the menu.
With Degauss selected from the menu, press button [2] to
degauss the monitor manually.
Important: Do not degauss repeatedly. Doing so can be
harmful to the display. Wait at least 20 minutes (before
selecting this control again.
ViewMatch® Color
provides several color options: several
preset color temperatures and User Color which allows you
to adjust red (R), green (G), and blue (B). The factory
setting for this product is 9300K (9300°
9300K
— Adds blue to the screen image for cooler white
Kelvin).
(used in most office settings with fluorescent lighting).
6500K
— Adds red to the screen image for warmer white
and richer red.
5000K
— Adds blue and green to the screen image for a
darker color.
User Color
— Individual adjustments for red, green, and
blue.
OSD Position
(On Screen Display) allows you to move the
menus and control screens.
Moire Reduction
reduces interference patterns that appear
as ripples, waves, or unwanted background color textures.
Interference patterns of this type are most noticeable when
viewing images having closely spaced lines or finely
detailed patterns.
Language
allows you to choose from among several
languages for the menus and control screens: English,
French, German, Italian, and Spanish.
ViewSonic E90fmb 9
Page 11
Control Explanation
Memory Recall
returns adjustments to the original factory
settings if the display is operating in a factory preset timing
mode listed in this user guide.
Exception: This control does not affect changes made with
the User Color control.
i
ViewMeter
vertical) coming from the graphics card of the computer.
displays the frequencies (horizontal and
10 ViewSonic E90fmb
Page 12
Other Information
Specifications
CRT
Input Signal
Compatibility
Resolution
Power
Display Area
Operating
Conditions
Ty p e
Dot Pitch
Phosphor
Glass surface
Video
Sync
PC
Macintosh
Recommended and
supported
Voltage AC 100-240 V / 50/60 Hz (auto switch)
Default
Full scan
Temperature
Humidity
Altitude
1
19” (18.0” viewable diagonal area), 90
29.1 mm Neck
0.21 mm horizontal, 0.13 mm vertical, and 0.25 mm
diagonal dot pitch
RGB medium/short persistence
TM~46%, anti-glare, anti-reflection
RGB Analog (0.7/1.0Vp-p, 75 Ohms
: 30-86 kHz, fv: 50-150 Hz
f
H
HV Separate (TTL), Composite
VGA up to 1280 x 1024
Power Macintosh
adapter)
1280 x 1024 @ 60, 75 Hz
1024 x 768 @ 60, 70, 72, 75, 85 Hz
800 x 600 @ 56, 60, 72, 75, 85 Hz
640 x 480 @ 60, 75, 85 Hz
640 x 400 @ 70 Hz
720 x 400 @ 70 Hz
640 x 350 @ 70 Hz
50/60 (+/- 3)Hz
354 mm (H) x 265 mm (V) (typical)
360 mm (H) x 270 mm (V) (depends on signal timing)
41° F to 104° F (-5° C to +40° C)
5% to 95% (no condensation)
To 9,000 feet
(may require Macintosh cable
o
deflection,
Storage
Conditions
Dimensions
Weight
Temperature
Humidity
Altitude
Physical
(monitor)
Net 22 kg (48.5 lb) (monitor only)
Regulations
Power Saving
Modes
1
Macintosh models prior to G3 require a Macintosh adapter. To order a ViewSonic® Macintosh adapter,
contact Customer Support. You will need to provide the product serial number.
NOTE: This product was designed for operation in the magnetic fields of the hemisphere where it was
purchased.
On
Off
-40° F to +140° F (-40° C to +60° C)
5% to 95% (no condensation)
To 39,000 feet
463.5 mm (W) x 4 91.5 mm (H) x 472 mm (D)
18.2” (W) x 19.4” (H) x 18.6” (D)
UL, cUL, DHHS, FCC-B, MPR-II, TUV/S, NOM, ICES003, E2000, MPRII, TUV/S-IRAM, EPA Energy Star
< 100 W TYPICAL (Green LED)
< 3 W (Orange LED)
®
ViewSonic E90fmb 11
Page 13
Troubleshooting
No power
• Make sure power button (or switch) is ON.
• Make sure A/C power cord is securely connected to the back of the monitor
and to a power outlet.
• Plug another electrical device (like a radio) into the power outlet to verify that
the outlet is supplying proper voltage.
Power is ON but no screen image
• Make sure the video cable supplied with the monitor is tightly secured to the
video output port on the back of the computer. If the other end of the video cable
is not attached permanently to the monitor, tightly secure it to the monitor.
• Adjust brightness and contrast.
• Verify whether an adapter is required for proper signal continuity between
graphics card and monitor.
Flickering
• Not enough power supplied. Connect the monitor to a different outlet. If
using a surge protector, reduce the number of devices plugged in.
• Check the ViewMeter from the main menu to verify the refresh rate (vertical
frequency) is 75 Hz or higher. See “Specifications” on page 11.
• Remove any devices from the area around the monitor that emit magnetic
fields such as radios, surge protectors, unshielded speakers, fluorescent
lights, AC power converters, desk fans, etc.
• Make sure the graphics card in your computer can use non-interlaced mode at
the desired frequencies. To enable your graphics card to support higher
refresh rates, try selecting fewer colors or running lower resolutions.
Wrong or abnormal colors
• If any colors (red, green, or blue) are missing, check the video cable to make
sure it is securely connected. Loose or broken pins in the cable connector
could cause an improper connection.
• Connect the monitor to another computer.
• Select Degauss from the Main Menu. Do this only once.
®
• If you have an older graphics card, contact ViewSonic
Customer Support.
Entire screen image rolls vertically
• Make sure video input signals are within the monitor's specified frequency range.
• Try the monitor with another power source, graphics card, or computer system.
• Connect the video cable securely.
Control buttons do not work
• Press only one button at a time.
12 ViewSonic E90fmb
Page 14
Customer Support
For technical support or product service, see the table below or contact your
reseller.
NOTE:
Country/
Region
United States
Canada
United Kingdom viewsoniceurope.com T: 0800 833 648
Europe, Middle
East, Baltic
countries, and
North Africa
Australia and New
Zealand
Singapore/India
and Southeast
Asia
You will need the product serial number.
Web site T = Telephone
F = FAX
viewsonic.com/
support
viewsonic.com/
support
viewsoniceurope.com Contact your
viewsonic.com.au T: +61 2 9929 3955
viewsonic.com.sg T: 65 273 4018
T: (800) 688-6688
F: (909) 468-1202
T: (800) 688-6688
F: (909) 468-1202
F: (01293) 643910
reseller
F: +61 2 9929 8393
F: 65 273 1566
Email
service.us@
viewsonic.com
service.ca@
viewsonic.com
service.eu@
viewsoniceurope.com
service.eu@
viewsoniceurope.com
service.au@
viewsonic.com
service.sg@
viewsonic.com
Other Asia/Pacific
countries
South Africa viewsonic.com/asia T: 886 2 2246 3456
viewsonic.com.tw T: 886 2 2246 3456
F: 886 2 8242 3668
F: 886 2 8242 3668
ViewSonic E90fmb 13
service.ap@
viewsonic.com
service.ap@
viewsonic.com
Page 15
Cleaning the Monitor
• MAKE SURE THE MONITOR IS TURNED OFF.
• NEVER SPRAY OR POUR ANY LIQUID DIRECTLY ONTO THE
SCREEN OR CASE.
To clean the screen:
1
Wipe the screen with a clean, soft, lint-free cloth. This removes dust and
other particles.
2
If still not clean, apply a small amount of non-ammonia, non-alcohol based
glass cleaner onto a clean, soft, lint-free cloth, and wipe the screen.
To clean the case:
1
Use a soft, dry cloth.
2
If still not clean, apply a small amount of a non-ammonia, non-alcohol
based, mild non-abrasive detergent onto a clean, soft, lint-free cloth, then
wipe the surface.
DISCLAIMER
ViewSonic does not recommend the use of any ammonia or alcohol-based
cleaners on the monitor screen or case. Some chemical cleaners have been
reported to damage the screen and/or case of the monitor. ViewSonic will not be
liable for damage resulting from use of any ammonia or alcohol-based cleaners.
14 ViewSonic E90fmb
Page 16
Limited Warranty
VIEWSONIC MONITORS
What the warranty covers:
ViewSonic
warranty period. If a product proves to be defective in material or workmanship during the warranty
period,
product or parts may include remanufactured or refurbished parts or components.
How long the warranty is effective:
ViewSonic
and three (3) years for all labor from the date of the first consumer purchase.
Who the warranty protects:
This warranty is valid only for the first consumer purchaser.
What the warranty does not cover:
1. Any product on which the serial number has been defaced, modified or removed.
2. Damage, deterioration or malfunction resulting from:
3. Removal, installation, and set-up service charges.
How to get service:
1.
2. To obtain service under warranty, you will be required to provide (a) the original dated sales slip, (b)
3. Take or ship the product freight prepaid in the original container to an authorized
4. For additional information or the name of the nearest
warrants its products to be free from defects in material and workmanship during the
ViewSonic
®
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product
modification, or failure to follow instructions supplied with the product.
b. Repair or attempted repair by anyone not authorized by
c. Any damage of the product due to shipment.
d. Removal or installation of the product.
e. Causes external to the product, such as electrical power fluctuations or failure.
f. Use of supplies or parts not meeting
g. Normal wear and tear.
h. Any other cause which does not relate to a product defect.
For information about receiving service under warranty, contact ViewSonic Customer
Support.
your name, (c) your address, (d) a description of the problem, and (e) the serial number of the
product.
service center or
will, at its sole option, repair or replace the product with a like product. Replacement
color monitors, including the display tubes, are warranted for three (3) years for all parts
ViewSonic.
ViewSonic
You will need to provide your product's serial number.
ViewSonic.
’s specifications.
ViewSonic
service center, contact
ViewSonic
ViewSonic
.
Limitation of implied warranties:
THERE ARE NO WARRANTIES, EXPRESS OR IMPLIED, WHICH EXTEND BEYOND THE
DESCRIPTION CONTAINED HEREIN INCLUDING THE IMPLIED WARRANTY OF
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
Exclusion of damages:
VIEWSONIC'S LIABILITY IS LIMITED TO THE COST OF REPAIR OR REPLACEMENT OF THE
PRODUCT. VIEWSONIC SHALL NOT BE LIABLE FOR:
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN THE PRODUCT, DAMAGES
BASED UPON INCONVENIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME, LOSS OF
PROFITS, LOSS OF BUSINESS OPPORTUNITY, LOSS OF GOODWILL, INTERFERENCE WITH
BUSINESS RELATIONSHIPS, OR OTHER COMMERCIAL LOSS, EVEN IF ADVISED OF THE
POSSIBILITY OF SUCH DAMAGES.
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUENTIAL OR OTHERWISE.
3. ANY CLAIM AGAINST THE CUSTOMER BY ANY OTHER PARTY.
Effect of state law:
This warranty gives you specific legal rights, and you may also have other rights which vary from state
to state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of
incidental or consequential damages, so the above limitations and exclusions may not apply to you.
Sales outside the U.S.A. and Canada:
For warranty information and service on
contact
ViewSonic Monitor Warranty (V2.0) Release Date: 10-15-1999
ViewSonic
or your local
ViewSonic
ViewSonic
dealer.
products sold outside of the U.S.A. and Canada,
ViewSonic E90fmb 15
Page 17
Appendix
yp
Safety Guidelines
CAUTION:
CAUTION:
certified for the individual country. Some examples are listed below:
The socket-outlet should be installed near the equipment and be easily accessible.
Use a power cable that is properly grounded. Always use the appropriate AC cord that is
USA................. UL
Canada............. CSA
Germany.......... VDE
Switzerland ..... SEV
Britain ............. BASE/BS
Japan ............... Electric Appliance Control Act
IMPORTANT NOTICE CONCERNING POWER CORD SELECTION
The power cord set for this unit has been enclosed and has been selected according to the country of
destination and must be used to prevent electric shock. Use the following guidelines if it is necessary to
replace the original cord set, or if the cord set is not enclosed.
The female receptacle of the cord set must meet IEC-60320 requirements and may look like (Figure A1
below):
Figure A1
Figure A2
For the United States and Canada
In the United States and Canada the male plug is a NEMA5-15 style (Figure A2), UL Listed, and CSA
Labeled. For units which are mounted on a desk or table, type SVT or SJT cord sets may be used. For
units which sit on the floor, only SJT type cord sets may be used. The cord set must be selected according
to the current rating for your unit. Please consult the table below for the selection criteria for power cords
used in the United States and Canada.
Cord T
SJT 18 AWG
SVT 18 AWG
e Size of Conductors in Cord Maximum Current Rating of Unit
16 AWG
14 AWG
17 AWG
10 Amps
12 Amps
12 Amps
10 Amps
12 Amps
For European Countries
In Europe you must use a cord set which is appropriate for the receptacles in your country. The cord set is HARCertified, and a special mark that will appear on the outer sheath, or on the insulation of one of the inner conductors.
AC PLUG CORD PRECAUTIONS FOR THE UNITED KINGDOM
FOR YOUR SAFETY PLEASE READ THE FOLLOWING TEXT CAREFULLY.
IF THE FITTED MOULDED PLUG IS UNSUITABLE FOR THE SOCKET OUTLET THEN THE PLUG SHOULD BE
CUT OFF AND DISPOSED OF SAFELY.
THERE IS A DANGER OF SEVERE ELECTRICAL SHOCK IF THE CUT OFF PLUG IS INSERTED INTO AN
APPROPRIATE SOCKET.
If a new plug is to be fitted, please observe the wiring code as shown below.
If in any doubt, please consult a qualified electrician.
WARNING:
IMPORTANT:
If the coloured wires of the mains lead of this appliance do not correspond with the coloured markings identifying the
terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by
the letter E or by the Earth symbol or coloured GREEN or GREEN-AND-YELLOW.
The wire which is coloured BLUE must be connected to the terminal in the plug which is marked with the letter N or
coloured BLACK. The wire which is coloured BROWN must be connected to the terminal in the plug which is marked
with the letter L or coloured RED.
If you have any questions concerning which proper power cord to use, please consult with the dealer from whom you
have purchased the product.
THIS APPLIANCE MUST BE EARTHED.
The wires in this mains lead are coloured in accordance with the following code:
Green-and-Yellow: Earth
Blue: Neutral
Brown: Live
16 ViewSonic E90fmb
Page 18
Compliance Information for U.S.A.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed
and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
FCC Warning
To assure continued FCC compliance, the user must use grounded power supply cord and the provided
shielded video interface cable with bonded ferrite cores. If a BNC cable is going to be used, use only a
shielded BNC(5) cable. Also, any unauthorized changes or modifications not expressly approved by the
party responsible for compliance could void the user's authority to operate this device.
Notice for Japan
This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information
Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may
cause radio interference. Install and use the equipment according to the instruction manual.
CE Conformity for Europe
The device complies with the requirements of the EEC directive 89/336/EEC as amended
by 92/31/EEC and 93/68/EEC Art.5 with regard to “Electromagnetic compatibility”, and 73/
23/EEC as amended by 93/68/EEC Art.13 with regard to “Safety”.
ViewSonic E90fmb 17
Page 19
NOTES
18 ViewSonic E90fmb
Page 20
ViewSonic Corporation
Loading...