ViewSonic CDE3205-EP User Guide

CDE3205-EP
Commercial Display

User Guide

IMPORTANT: Please read this User Guide to obtain important information on installing
and using your product in a safe manner, as well as registering your product for future
service. Warranty information contained in this User Guide will describe your limited
coverage from ViewSonic Corporation, which is also found on our web site at http://
www.viewsonic.com in English, or in specific languages using the Regional selection
box in the upper right corner of our website. “Antes de operar su equipo lea cu
idadosamente las instrucciones en este manual”

Model No. VS17182

Thank you for choosing ViewSonic

As a world leading provider of visual solutions, ViewSonic is dedicated to
exceeding the world’s expectations for technological evolution, innovation, and
simplicity. At ViewSonic, we believe that our products have the potential to

make a positive impact in the world, and we are condent that the ViewSonic

product you have chosen will serve you well.

Once again, thank you for choosing ViewSonic !

Compliance Information

NOTE: This section addresses all connected requirements and statements regarding regulations.

Confirmed corresponding applications shall refer to nameplate labels and relevant markings on
unit.

CE Conformity for European Countries

The device complies with the EMC Directive 2014/30/EU and Low Voltage Directive
2014/35/EU.

Declaration of RoHS2 Compliance

This product has been designed and manufactured in compliance with Directive 2011/65/EU of the
European Parliament and the Council on restriction of the use of certain hazardous substances in
electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum
concentration values issued by the European Technical Adaptation Committee (TAC) as shown
below:

Substance

Lead (Pb) 0,1% < 0,1%
Mercury (Hg) 0,1% < 0,1%
Cadmium (Cd) 0,01% < 0,01%
Hexavalent Chromium (Cr
Polybrominated biphenyls (PBB) 0,1% < 0,1%
Polybrominated diphenyl ethers (PBDE) 0,1% < 0,1%

Certain components of products as stated above are exempted under the Annex III of the RoHS2
Directives as noted below:

Examples of exempted components are:

1. Lead as an alloying element in aluminium containing up to 0.4% lead by weight.

2. Copper alloy containing up to 4% lead by weight.

3. Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight
or more lead).

6+

) 0,1% < 0,1%

Proposed Maximum
Concentration

Actual Concentration

4. Electrical and electronic components containing lead in a glass or ceramic other than dielectric
ceramic in capacitors, e.g. piezoelectronic devices, or in a glass or ceramic matrix compound.

Warning:

This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take adequate measures.

i

Safety Precautions

FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE FOLLOWING WHEN SETTING UP AND
USING THE LCD COLOR MONITOR:

• DO NOT REMOVE MONITOR BACK COVER. There are no user serviceable parts inside and
opening or removing covers may expose you to dangerous shock hazards or other risks. Refer

all servicing to qualied service personnel.

• Do not spill any liquids into the cabinet or use your monitor near water.

• Do not insert objects of any kind into the cabinet slots, as they may touch dangerous voltage
points, which can be harmful or fatal or may cause electric shock, re or equipment failure.

• Do not place any heavy objects on the power cord. Damage to the cord may cause shock or
re.

• Do not place this product on a sloping or unstable cart, stand or table, as the monitor may fall,

causing serious damage to the monitor.

• Do not place any objects onto the monitor and do not use the monitor outdoors.

• The inside of the uorescent tube located within the LCD monitor contains mercury. Please

follow the laws or rules of your municipality to dispose of the tube properly.

• Do not bend power cord.

• Do not use monitor in high temperature, humid, dusty, or oily areas.

• If monitor or glass is broken, do not come in contact with the liquid crystal and handle with

care.

• Allow adequate ventilation around the monitor, so that heat can properly dissipate. Do not
block ventilated openings or place the monitor near a radiator or other heat sources. Do not
put anything on top of the monitor.

• The power cable connector is the primary means of detaching the system from the power
supply. The monitor should be installed close to a power outlet, which is easily accessible.

• Handle with care when transporting. Save packaging for transporting.

• Please clean the holes of back cabinet to reject dirt and dust at least once a year because of

set reliability.

• If using the cooling fan continuously, it’s recommended to wipe holes a minimum of once a
month.

• When installing the remote control batteries;

- Align the batteries according to the (+) and (-) indications inside the case.

- Align the (-) indication of the battery rst inside the case.

• Usage of other than specied head- or earphones can result in hearing loss due to excessive

sound pressures.

ii

CAUTION:

Immediately unplug your monitor from the wall outlet and refer servicing to qualified service
personnel under the following conditions:

• When the power supply cord or plug is damaged.

• If liquid has been spilled, or objects have fallen into the monitor.

• If the monitor has been exposed to rain or water.

• If the monitor has been dropped or the cabinet damaged.

• If the monitor does not operate normally by following operating instructions.

Recommended Use

CAUTION:

• For optimum performance, allow 20 minutes for warm-up.

• Rest your eyes periodically by focusing on an object at least 5 feet away. Blink often.

• Position the monitor at a 90° angle to windows and other light sources to minimize glare and
reections.

• Clean the LCD monitor surface with a lint-free, nonabrasive cloth. Avoid using any cleaning

solution or glass cleaner!

• Adjust the monitor’s brightness, contrast and sharpness controls to enhance readability.

• Avoid displaying xed patterns on the monitor for long periods of time to avoid image

persistence (after image effects).

• Get regular eye checkups.

Ergonomics

To realize the maximum ergonomic benefits, we recommend the following:

• Use the preset Size and Position controls with standard signals.

• Use the preset Color Setting.

• Use non-interlaced signals.

• Do not use primary color blue on a dark background, as it is difcult to see and may produce
eye fatigue due to insufcient contrast.

iii

Table Of Contents

1. Unpacking and Installation .................. 1

1.1. Unpacking ...................................... 1

1.2. Package Contents .......................... 1

1.3. Installation Notes ............................ 1

1.4. Mounting on a Wall ......................... 2

1.4.1. Using HDMI video input ....... 2

1.5. Using of Remote sensor and power

indicator ......................................... 3

2. Parts and Functions ............................. 4

2.1. Control Panel ................................. 4

2.2. Input/Output Terminals ................... 5

2.3. Remote Control .............................. 6

2.3.1. General functions ................. 6

2.3.2. Inserting batteries in the

remote control ...................... 7

2.3.3. Handling the remote control . 7

2.3.4. Operating range of the remote

control .................................. 7

3. Connecting External Equipment ......... 8

3.1. Connecting External Equipment

(DVD/VCR/VCD) ............................ 8

3.1.1. Using HDMI video input ....... 8

3.1.2. Using Video Source input .... 8

3.1.3. Using HDMI video input ....... 8

3.2. Connecting a PC ............................ 9

3.2.1. Using VGA input ................... 9

3.2.2. Using DVI input .................... 9

3.2.3. Using HDMI input ................. 9

3.3. Connecting Audio Equipment ....... 10

3.3.1. Connecting an external audio

device ................................. 10

3.4. Connecting Multiple Displays in a

Daisy-chain Conguration ............ 10

3.4.1. Display control connection . 10

3.5. IR Pass-through Connection ........11

3.6. Wire-connecting to Network .........11

4.4. Play options .................................. 13

4.4.1. Playing music les ............. 13

4.4.2. Playing movie les ............. 14

4.4.3. Playing photo les .............. 14

5. Change your settings ......................... 15

5.1. Settings ........................................ 15

5.1.1. Picture menu ...................... 15

5.1.2. Screen menu ...................... 16

5.1.3. General settings menu ....... 16

5.2. Network Settings .......................... 17

6. USB device compatibility ................... 18

7. Input mode .......................................... 20

8. Cleaning and Troubleshooting .......... 21

8.1. Cleaning ....................................... 21

8.2. Troubleshooting ............................ 22

9. TechnicalSpecications .................... 23

9.1. CDE3205-EP ................................ 23

10. RS232 Protocol ................................... 25

10.1. Introduction .................................. 25

10.2. Description ................................... 25

10.2.1. Hardware specication ..... 25

10.2.2. Communication Setting .... 25

10.2.3. Command Message

Reference .......................... 25

10.3. Protocol ........................................ 26

10.3.1. Set-Function Listing .......... 26

10.3.2. Get-Function Listing ......... 29

10.3.3. Remote Control Pass-

through mode ..................... 32

11. Other Information ............................... 35

Customer Support................................. 35

Limited Warranty .................................. 36

Mexico Limited Warranty ...................... 38

4. Operation ............................................. 12

4.1. Watch the Connected Video

Source .......................................... 12

4.2. Change Picture Format ................ 12

4.3. Play Multimedia Files ................... 12

4.3.1. Play les from computer and

mobile device ..................... 12

4.3.2. USB Multimedia Player

for Scheduled Playback of
Videos, Photos and Music . 13

4.3.3. Play multimedia les from

USB device ........................ 13

iv

Copyright Information

Copyright © ViewSonic® Corporation, 2017. All rights reserved.
ViewSonic

ViewSonic Corporation.
ENERGY STAR
Disclaimer: ViewSonic Corporation shall not be liable for technical or editorial errors or omissions

contained herein; nor for incidental or consequential damages resulting from furnishing this
material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic Corporation reserves the right to
change product specifications without notice. Information in this document may change without
notice.

No part of this document may be copied, reproduced, or transmitted by any means, for any purpose
without prior written permission from ViewSonic Corporation.

©

, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of

®

is a registered trademark of the U.S. Environmental Protection Agency (EPA).

Product Registration

To meet your future needs, and to receive any additional product information as it becomes
available, please register your product on the Internet at:
www.viewsonic.com.

The ViewSonic
which you may mail or fax to ViewSonic.

®

Wizard CD-ROM also provides an opportunity for you to print the registration form,

For Your Records

Product Name:

Model Number:
Document Number:
Serial Number:
Purchase Date:

Product disposal at end of product life

ViewSonic respects the environment and is committed to working and living green. Thank you for
being part of Smarter, Greener Computing.

Please visit ViewSonic website to learn more.
USA & Canada: http://www.viewsonic.com/company/green/recycle-program/
Europe: http://www.viewsoniceurope.com/eu/support/call-desk/
Taiwan: http://recycle.epa.gov.tw/recycle/index2.aspx

CDE3205-EP
ViewSonic Commercial Display
VS17182
CDE3205-EP_UG_ENG Rev. 1A 09-18-17

v

1. Unpacking and Installation

1.1. Unpacking

• This product is packed in a carton, together with the standard accessories.

• Any other optional accessories will be packed separately.

• Due to the size and weight of this display it is recommended for two people to move it.

• After opening the carton, ensure that the contents are complete and in good condition.

1.2. Package Contents

Please verify that you received the following items with your package content:

• LCD display

• CD ROM

• Remote control with AAA

batteries

• Quick Start Guide

• Power cord (1.8 m)

• VGA cable (1.8 m)

• RS232 cable (1.8 m)

• RS232 daisy chain cable

(2.4mm-2.4mm)

• IR sensor cable

* The supplied power cord varies depending on destination.

For EU For China

Remote Control

and AAA Batteries

CD ROM

(D-SUB to D-SUB Cable)

IR sensor cable

Video Signal Cable

CDE3205-EP

Commercial Display

Quick Start Guide

1

2

PC

USB

USB

INOUTRJ45IN

OUT

LRLR

AC IN

Y Pb Pr

DVD / VCR / VCD

Quick Start Guide

For North America For UK

RS232 Cable RS232 daisy chain cable

NOTES:

• For all other regions, apply a power cord that conforms to the AC voltage of the power socket and has
been approved by and complies with the safety regulations of the particular country.

• Keep the package box and packing material for shipping the display.

1.3. Installation Notes

• Due to the high power consumption, always use the plug exclusively designed for this product. If an
extended line is required, please consult your service agent.

• The product should be installed on a at surface to avoid tipping. The distance between the back of

the product and the wall should be maintained for proper ventilation. Avoid installing the product in the
kitchen, bathroom or any other places with high humidity so as not to shorten the service life of the
electronic components.

• The product can normally operate only under 2000 m in altitude. In installations at altitudes above 2000 m,
some abnormalities may be experienced.

1

1.4. Mounting on a Wall

To mount this display to a wall, you will have to obtain a standard wall-mounting kit. We recommend using a
mounting interface that complies with UL1678 standard in North America.

Protective Sheet

VESA Grid

Table

1. Lay a protective sheet on a table, which was wrapped around the display when it was packaged, beneath
the screen surface so as not to scratch the screen face.

2. Ensure you have all accessories for mounting this display (wall mount, ceiling mount, table stand, etc)

3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting
procedures could result in damage to the equipment or injury to the user or installer. Product warranty
does not cover damage caused by improper installation.

4. For the wall-mounting kit, use M4 mounting screws (having a length 10 mm longer than the thickness of
the mounting bracket) and tighten them securely.

5. Unit without base weight= W Kg.The equipment and its associated mounting means still remain secure
during the test. For use only with UL Listed Wall Mount Bracket with minimum weight/load: W Kg.

Model W (kg)

CDE3205-EP 5.2

1.4.1. Using HDMI video input

Model Vesa Grid

CDE3205-EP 100(H) x 100(V)mm / 200(H) x 200(V)mm

Caution:

To prevent the display from falling:

• For wall or ceiling installation, we recommend installing the display with metal brackets which are
commercially available. For detailed installation instructions, refer to the guide received with the
respective bracket.

• To lessen the probability of injury and damage resulting from fall of the display in case of earthquake or
other natural disaster, be sure to consult the bracket manufacturer for installation location.

2

Ventilation Requirements for enclosure locating

To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.

100 mm

100 mm 100 mm

100 mm

1.5. Using of Remote sensor and power indicator

1. Pull down the lens to have better remote control performance and easy to observe the light information of
power status.

2. Push up the lens before mounting the display for video wall application.

3. Pull/Push the lens until hearing the click sound.

Push right to collapse the lens Push left to extend the lens

3

2. Parts and Functions

2.1. Control Panel

MUTE INPUT

1 2 3 4 5 6 7 8

1

[ ] button

Use this button to turn the display on or put the
display to standby.

2

[MUTE] button

Switch the audio mute ON/OFF.

3

[INPUT] button

Choose the input source.

• Used as [OK] button in the On-Screen-Display

menu.

4

[ ] button

Move the highlight bar up / Increase the adjustment
while OSD menu is on, or increase the audio output
level while OSD menu is off.

MENU

5

[ ] button

Move the highlight bar down / Decrease the
adjustment while OSD menu is on, or decrease the
audio output level while OSD menu is off.

6

[ ] button

Move the highlight bar up to adjust the selected item
while OSD menu is on.

7

[ ] button

Move the highlight bar down to adjust the selected
item while OSD menu is on.

8

[[MENU] button

Return to previous menu while OSD menu is on, or
to activate the OSD menu when OSD menu is off.

4

2.2. Input/Output Terminals

2

3 4

1

MAIN POWER SWITCH

Switch the main power on/off.

USB

INOUTRJ45IN

1

OUT

LRL R

Y Pb Pr

16

5

6

7

10

IR OUT / 11 IR IN

15

14

13

12

11

10

9

8

IR signal output /input for the loop-through function.

2

AC IN

AC power input from the wall outlet.

3

PC LINE IN

Audio input from VGA source (3.5mm stereo phone).

4

HDMI IN

HDMI video / audio input.

5

DVI-D IN

DVI-D video input.

6

VGA IN (D-Sub)

VGA video input.

7

Y/CVBS

Video source input.

8

AUDIO IN

Audio input from external AV device (RCA).

9

AUDIO OUT

Audio output to external AV device.

NOTES:

• This display’s remote control sensor will stop

working if the jack [IR IN] is connected.

• To remotely control your A/V device via this

display, refer to page 11 for IR Pass Through
connection.

12

RJ-45

LAN control function for the use of remote control
signal from control center.

13

RS232 OUT / 14 RS232 IN

RS232C network output / input for the loop-through
function.

15

USB PORT

Connect your USB storage device.

16

Security LOCK

Used for security and theft prevention.

5

2.3. Remote Control

2.3.1. General functions

1

2

3

4

5

6
7
8

9

10

11

12

20

13

14

15

16

17

18

19

21

8

[ADJUST] button

Press to run the Auto Adjust function.
NOTE: This button is functional for VGA input only.

9

[ ] button

Press to move the se

10

[ ] MUTE button

tion down in OSD menu.

lec

Press to turn the mute function on/off.

11

COLOR buttons

Choose tasks or options.(for Media Input only).

12

[NUMERIC] buttons

Enter text for network setting.

13

Format button

Press to switch screen aspect ratio.

14

[EXIT] button

Press to turn back to the previous OSD menu.

15

[INFO] button

Press to turn on/off the information OSD displayed
on the upper right corner of the screen.

16

[ ] button

Press to increase the value in OSD menu.

17

[OPTION] button

Access currently available options, picture and
sound menus (for Media Input only).

18

[+] Volume up button

Press to increase the audio output level.

19

[-] Volume down button

Press to decrease the audio output level.

20 21

[ID SET] button

No function.

1

[POWER] button

Press to switch on the display from standby mode.
Press again to turn it off and back into standby
mode.

2

[PLAY] button

Control playback of media les (for Media Input

only).

3

[ SOURCE] button

Press to toggle Video Source Menu. Press [

] or

[ ] button to select one of the video sources among

Displayport, DVI-D, VGA, HDMI1, HDMI2, Media
Player, Browser or PDF Player. Press [OK] button.

4

[MENU] button

Press to turn the OSD menu on/off.

5

[ ] button

Press to move the selection up in OSD menu.

6

[ ] button

Press to decrease the value in OSD menu.

7

[OK] button

Press to activate the setting inside the OSD menu.

6

2.3.2. Inserting batteries in the remote control

The remote control is powered by two 1.5V AAA batteries.

To install or replace batteries:

1. Press and then slide the cover to open it.

2. Align the batteries according to the (+) and (–)
indications inside the battery compartment.

3. Replace the cover.

Caution:

The incorrect use of batteries can result in leaks or bursting. Be sure to follow these instructions:

• Place “AAA” batteries matching the (+) and (–) signs on each battery to the (+) and (–) signs of the
battery compartment.

• Do not mix battery types.

• Do not combine new batteries with used ones. It causes shorter life or leakage of batteries.

• Remove the dead batteries immediately to prevent them from liquid leaking in the battery compartment.

Don’t touch exposed battery acid, as it can damage your skin.

NOTE: If you do not intend to use the remote control for a long period, remove the batteries.

2.3.3. Handling the remote control

• Do not subject to strong shock.

• Do not allow water or other liquid to splash the remote control. If the remote control gets wet, wipe it dry

immediately.

• Avoid exposure to heat and steam.

• Other than to install the batteries, do not open the remote control.

2.3.4. Operating range of the remote control

Point the front of the remote control toward this display’s
remote control sensor when pressing a button.

Use the remote control within a distance of less than 10m/33ft
from this display’s sensor, and a horizontal and vertical angle
of less than 30 degrees.

NOTE: The remote control may not function properly when

the remote control sensor on this display is under
direct sunlight or strong illumination, or when there is
an obstacle in the path of signal transmission.

30 30

7

3. Connecting External Equipment

AC IN

LRL R

INOUTRJ45IN USB

OUT

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

DVD / VCR / VCD

[AUDIO IN]

[COMPONENT IN]

(YPbPr)

COMPONENT Out
(YPbPr)

Audio Out

[R]

[L]

3.1. Connecting External Equipment (DVD/VCR/VCD)

3.1.1. Using HDMI video input

Audio Out

AC IN

3.1.2. Using Video Source input

AC IN

USB

INOUTRJ45IN

OUT

[R]

LRL R

[L]

DVD / VCR / VCD

[AUDIO IN]

COMPONENT Out
(YPbPr)

[COMPONENT IN]

(YPbPr)

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

Y/CVBS Out

USB

INOUTRJ45IN

OUT

[R]

LRL R

[L]

DVD / VCR / VCD

[AUDIO IN]

[Y/CVBS IN]

3.1.3. Using HDMI video input

AC IN

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

USB

INOUTRJ45IN

DVD / VCR / VCD

OUT

LRL R

[HDMI IN]

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

HDMI Out

8

3.2. Connecting a PC

AC IN

LRL R

INOUTRJ45IN USB

OUT

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

DVD / VCR / VCD

HDMI Out

[HDMI IN]

AC IN

AC IN

LRL R

INOUTRJ45IN USB

OUT

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

DVD / VCR / VCD

HDMI Out

[HDMI IN]

LRL R

INOUTRJ45IN USB

OUT

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

PC

[VGA IN]

[VGA AUDIO IN]

VGA Out

D-Sub 15 pin

Audio Out

3.2.1. Using VGA input

3.2.2. Using DVI input

AC IN

USB

INOUTRJ45IN

VGA Out

D-Sub 15 pin

Audio Out

OUT

LRL R

[VGA IN]

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

PC

[VGA AUDIO IN]

USB

INOUTRJ45IN

OUT

LRL R

DVI Out

PC

AC IN

3.2.3. Using HDMI input

AC IN

[DVI IN]

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

USB

INOUTRJ45IN

OUT

LRL R

[HDMI IN]

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

Audio Out

[VGA AUDIO IN]

HDMI Out

PC

9

3.3. Connecting Audio Equipment

AC IN

LRL R

INOUTRJ45IN USB

OUT

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

PC

HDMI Out

[HDMI IN]

3.3.1. Connecting an external audio device

AUDIO OUT

STEREO AMPLIFIER

COMPONENT OUT (YPbPr)

DVD / VCR / VCD

AC IN

USB

INOUTRJ45IN

OUT

LRL R

AUDIO IN

HDMI IN DVI IN COMPONENT INVGA INPC Line IN

3.4. Connecting Multiple Displays in a Daisy-chain Configuration

You can interconnect multiple displays to create a daisy-chain conguration for applications such as a video

wall.

3.4.1. Display control connection

Connect the [RS232C OUT] connector of DISPLAY 1 to the [RS232C IN] connector of DISPLAY 2.

PC

[RS-232C]

DISPLAY 1

[RS-232C IN] [RS-232C OUT] [RS-232C IN]

DISPLAY 2

10

3.5. IR Pass-through Connection

[IR OUT]

DISPLAY

(DVD / VCR / VCD)

Remote Control

DVD / VCR / VCD

[IR IN]

3.6. Wire-connecting to Network

If you connect this display to a home network, you can play photos, music and videos from your computer.

See Play multimedia les via Local Area Network (Page 13) for more detail.

INTERNET

[RJ-45]

PC

ROUTER

[RJ-45]

To setup the network:

1. Switch on the router and switch on its DHCP setting.

2. Connect the router to this display with an Ethernet cable.

3. Press [

4. Press ▲ or ▼ button to select the menu item {Network settings}. Press SET button to enter its submenu.

5. Press ▲, ▼, ,  to adjust its value. Press SET button to conrm.

] MNEU button to display the OSD menu.

11

4. Operation

NOTE: The control button described in this section

is mainly on the remote control unless

specied otherwise.

4.1. Watch the Connected Video Source

See page 8 for external equipments
connection.

1. Press

2. Press

3. press OK button.

4.2. Change Picture Format

You can change the picture format to suit the video
source. Each video source has its available picture
formats.

The available picture formats depend on the video
source:

1. Press

2. Press
then press button.

• {FULL}: Enlarge the picture to ll the screen.

• {NORMAL}: 4:3 format.

• {CUSTOM}: 16:9 format.

• {REAL}: This mode displays the image pixel-

by-pixel on screen without scaling the original
image size.

• {DYNAMIC}: Auto format.

4.3. Play Multimedia Files

You can play videos, photos, and music on your
display from:

• Your computer and mobile device connected
through your network.

• USB Multimedia Player for Scheduled Playback
of Videos, Photos and Music.

• A USB device connected to this display.

4.3.1. Play files from computer and mobile

To play les from computer and mobile device, you

will need:

• The CDE3205-EP features a RJ45 port to
connect directly with PCs or notebooks via
Intranet connection. This provides for the

efcient loading of content onto multiple

displays through a primary display. DLNA like
mobile devices can also utilize a wireless hub
to push multimedia content directly to selected
displays.

• A wired network, connected with a Universal
Plug and Play (uPnP) router.

SOURCE button.

or button to select a device, then

FORMAT button

or button to select a picture format,

device

• Optional: A LAN cable that connects your
display to your network.

• A media server running on your computer.

• Appropriate settings on your computer rewall

to allow you to run the media server.

Set up the network

1. Connect your display and the computer to the
same network. See page 9 for connecting your
display to a network.

2. Switch on your computer and the router.

NOTE: If the apparatus does not return to Network

mode due to external electrical disturbances
(e.g. electrostatic discharge), user intervention is
required.

Set up media sharing

1. Install a media server on your computer to

share media les. These are some media

servers:

• For PC: Windows Media Player 11 (or higher)
or TVersity

• For Mac: Twonky

2. Switch on media sharing on your computer
using the media server. For more information
on how to set up the media server, refer to the
website of the media server.

Playles

1. Press

2. Select [Browse network], then press OK button.

3. Select a le from the content browser, then
press OK button to statrtheplnaying.

4. Press the Play buttons on the remote control to
control playing.

Tips:

• Select the top bar to lter your les by type.

• Select [Sort] to arrange the les by album
name, ar tist, or other elds.

• To clear the list of ofine media servers, press

OPTIONS button, then select [Clear ofine

servers] and press OK button.

button.

12

4.3.2. USB Multimedia Player for Scheduled

USB deviceSortPlay All OptionsInfo

Playback of Videos, Photos and Music

With the handy PC-less USB playback feature,
photos, music and 1080p video can be
immediately displayed on-screen from a USB
drive. A user-friendly on-screen scheduling
interface also lets you select time and date, as well

as repeat and shufe settings, or choose specic

content to play from the attached USB source. (See
page 14 USB scheduling)

4.3.3. Play multimedia files from USB device

This display can play music, movie, or photo les

from your USB device.

1. Connect your USB device to the USB port on
this display.

USB

USB

INOUTRJ45IN

OUT

LRL R

Supportedlesystem:

• FAT32

Supportedleformat:

• Music: MP3, WMA, M4A, AAC, AC3

• Movie: AVI, MP4, MOV, MPG/MPEG

• Photo: JPEG, BMP, GIF

Caution:

• The manufacturer is not responsible if the USB
device is not supported, nor is it responsible for
damage to or loss of data in the device.

• Do not overload the USB port. If you connect a
USB storage device that consumes more than
500mA power, make sure that it is connected to
its own external power supply.

NOTE: When you are playing multimedia les

from USB device and turn the display off. It will set
input source to the last real input source, such as
CVBS,YPbPr,VGA, HDMI and DVI-D when you
turn the display on next time.

2. Press

SOURCE button, select USB, then

press OK button.

3. The connected USB device is detected

automatically for all its playable les, which will

be automatically sor ted into 3 types: Music

Movie

, and Photo .

4. Press the button to go up to the top layer in
the screen. Press   button to select the le
type. Press OK button to enter its play list.

5. Select the le you want. Press OK button to
start playing.

6. Follow the on-screen instruction to control the
play option.

7. Press the PLAY buttons (

) to

control playing.

4.4. Play options

4.4.1. Playing music files

1. Select Music

2. Select one music track, then press OK button.

,

Album

• To play all the tracks in a folder, select one

music le, then select {Play All}.

• To skip to the next or previous track, press

button.

• To pause the track, press OK button. Press OK

button again to resume playback.

• To skip backward or forward 10 seconds, press
or  button.



• To search backward or forward, press

button, press repeatedly to toggle between

different speeds.

• To stop the music, press

in the top bar.

05:051. Music

button.

or

or

13

Music options

While you play music, press button, then press

OPTIONS button to select an option:

• {Repeat}: Select {Repeat} to play a track or an
album repeatedly, or select {Play once} to play

a track once.

• {Media Server}: When you play content from

a media server, you can select another media
server.

• {Shufe On} / {Shufe Off}: Enable or disable

random play of tracks.

NOTE: To view information about a song (for

example, title, artist or duration), select the song,
then press
press

INFO button.To hide the information,

INFO button again.

4.4.2. Playing movie files

1. Select Movie

in the top bar.

2. Select a video, then press OK button.

• {Repeat}: Select {Repeat} to play the video le
repeatedly or {Play once} to play the video le

once.

• {Media server}: When you play content from

a media server, you can select another media
server.

• {Shufe On} / {Shufe Off}: Enable or disable
random play of video les.

NOTE: To view information about a video (for

example, played position, duration, title, or date),
select the video, then press
hide the information, press

INFO button.To

INFO button again.

4.4.3. Playing photo files

1. Select Photo

in the top bar.

2. Select a photo thumbnail, then press OK
button.

Date

Track

USB devicePlay All OptionsInfo

• To play all the videos in a folder, select one

video le, then select {Play All}.

• To skip to the next or previous video, press

or button.

• To pause the video, press OK button. Press OK

button again to resume playback.

• To skip backward or forward 10 seconds, press
or  button.



• To search backward or forward, press

or

button, press repeatedly to toggle between

different speeds.

• To stop the video, press

button.

Movie options

While playing video, press

OPTIONS button,

then press OK button to select an option:

• {Subtitles}: Select the available subtitle settings.

• {Subtitle Language}: Select the language for

subtitles if available.

• {Character Set}: Select the correct character

set for the subtitles.

• {Audio Language}: Select an audio language.

USB deviceSortPlay All OptionsInfo

Start a slideshow

If there are multiple photos in a folder, select a

photo, then select {Play All}.

• To skip to the previous or next photo, press 

or  button, and then press OK button.

• To stop the slideshow, press

button.

Slideshow options

While you play a slideshow, press OPTIONS
button, then press OK button to select an option:

• {Shufe Off} / {Shufe On}: Enable or disable

random display of pictures in the slideshow.

• {Repeat}: Select {Repeat} to watch a slideshow
repeatedly or {Play once} to watch once.

• {Slideshow Time}: Select the displaying time for

each photo in the slideshow.

• {Slideshow Transitions}: Select the transition

from one photo to the next.

• {Media Server}: When you play content from

a media server, you can select another media
server.

14

5. Change your settings

5.1. Settings

Using the remote control:

1. Press the [ ] MENU button to display the OSD

menu.

2. Press [

] [ ] [ ] or [ ] button to select its menu

item or to adjust its value. Press OK button to

conrm.

3. Press [

] EXIT button to go back to the

previous menu layer.

4. Press EXIT button to exit the OSD menu.

Using this display’s control buttons:

5.1.1. Picture menu

Picture

Sound
General settings
Network settings

Picture style
Restore style
Brightness
Contrast
Black level
Hue
Colour
Sharpness
Advanced
Video or PC
Foramat and edges

Picture style

Select a predened picture setting.

Restore style

Restore the last-selected predened picture

setting.

Brightness

Adjust the brightness of this display’s backlight.

Contrast

Adjust video contrast.

1. Press the MENU button to display the OSD

menu.

2. Press the [

] [ ] [ ] or [ ] to select menu item

or adjust its value.

3. Press [INPUT] button to conrm menu selection

and enter its submenu.

4. Press MENU to conrm menu selection and

enter its submenu.

Black level

Adjust screen brightness.

Hue

Adjust screen hue.

Colour

Adjust the colour saturation of the picture.

Sharpness

Adjust the sharpness of the picture.

Advanced

Access advanced settings such as gamma, tint
settings and video contrast settings.

• {Noise reduction}: Select the amount of noise

reduction for the picture.

• {Gamma}: Adjust the non-linear setting for

picture luminance and contrast.

• {Color temp.}: Change the colour balance.

• {Custom color temp.}: Customise colour

balance setting.

• {Advanced sharpness}: Enable superior

sharpness, especially on lines and contours in
the picture.

• {Dynamic contrast}: Dynamically enhance the

details in the dark, medium and light areas of
the picture.

15

• {Dynamic backlight}: Select a backlight level

to optimise dynamic power consumption and
picture contrast.

• {Colour enhancement}: Dynamically enhance

the vividness and details of colours.

Video or PC

When viewing content from a connected video

console, select {Video} to apply video settings.

When a computer is connected through HDMI,

select {PC}.

Make sure that {Format and edges}

{Picture

format} {Unscaled} is selected so as to view

maximum detail.

Format and edges

Access advanced settings to control the displaying
format of the picture.

• {Picture format}: Change the picture format.

• {Picture shift}: If available, move the position of

the picture

5.1.2. Screen menu

Picture

Sound

General settings
Network settings

Sound style
Restore style
Bass
Treble
Audio out
Advanced

• {Auto volume leveling}: Enable the reduction of

sudden volume changes.

• {Speaker}:Turn on or off the internal speakers.

• {Clear sound}: Enhance sound quality.

5.1.3. General settings menu

Picture
Sound

General settings

Network settings

Menu language
Monitor id
Eco mode
Auto search
Clock
Scheduling
Sleep timer
Auto switch off
Auto adjust
Pixel shift
Control settings
Factory settings

Menu language

Select language used for OSD menus.

Monitor id

Set the ID number for controlling this display via
the RS232C connection. Each display must have
a unique ID number when multiple sets of this
display are connected.

Eco mode

Set this display to reduce the power consumption
automatically.

Sound style

Access predened sound settings.

Restore style

Restore the last-selected predened sound setting.

Bass

Adjust the bass level of the speaker and
headphones.

Treble

Adjust the treble level of the speaker and
headphones.

Audio out

Adjust audio output volume.

Advanced

Access advanced settings to enhance your audio
experience.

Auto search

Choose to let this display detect and display
available signal sources automatically.

Clock

Adjust clock settings

Scheduling

This function allows you to program up to 3
different scheduled time intervals for this display to
activate.

You can set:

• Which input source the display will use for each
scheduled activation period.

• The time for the display to turn on and turn off.

• The days in a week for the display to activate.

NOTES:

• We recommend you to set up current date
and time in the {Clock} menu before using this

function.

• After changing the {Clock} option in the
{General settings} menu, you need to set this
{Scheduling} again.

16

Sleep timer

Switch off this display after a specied time.

Auto switch off

Set the time for this display to be switched off
after a period of no activity. Press any key on the
remote control to disable this function.

Auto adjust

Use this function to automatically optimize the
display of VGA input image.

: This item is functional for VGA input only.

Note

Pixel shift

For video input sources, you may choose {On} to

move the screen
image automatically to protect the display from

“burn-in” or “after-image”
symptoms 30 seconds after not operating the

display.

Control settings

• {Local KB lock}: Choose to enable or disable

the keyboard (control buttons) function of this
display.

• {Unlock}: Enable the keyboard function.

• {Lock all}: Lock all keyboard function.

• {Lock but volume}: Disable all the keyboard

function except the VOL+ and VOL- button.

• {Lock but power}: Disable all the keyboard

function except the

POWER button.

• {RC lock}: Choose to enable or disable the

button function of the remote control.

• {Unlock}: Enable the button function.

• {Lock all}: Lock all button function.

• {Lock but volume}: Disable all the button

function except VOL+ and VOL- button.

• {Lock but power}: Disable all the button

function except the

POWER button.

5.2. Network Settings

Picture
Sound
General settings

Network settings

View network settings

View connected network status.

Network settings

Select how this display should assign addresses
to the network resources.

StaticIPConguration

Assign {IP address}, {Netmask}, {Gateway},
{DNS1}, and {DNS2} for this display.

Digital Media Renderer - DMR

Receive multimedia les from Smar t Phones or

Tablets connected to your network.

Wake on lan

Choose On and you can turn on the
display by network.

Network name

Rename this display for easy identication if you

have more than one display connected to your
network.

View network settings
Network configuration
Static IP configuration
Digital Media Render...
Wake On LAN
Network name

NOTE:

To disable the lock function from [Local KB lock]
or [RC lock] item, press buttons

1 9 9 8 on the

remote control.

Factory settings

Reset all your customized settings to the factory
defaults.

17

6. USB device compatibility

File

Extensions

.mpg

mpeg

.vob

.ts TS

.ts

.m2ts

.mts
.mt2

Container Video codec Maximum resolution

MPEG-1 1920x1080 25p,30p,50i,60i 30 MPEG-1

PS

MaTS

TTS

MPEG-2 1920x1080 25p,30p,50i,60i 30

MPEG-4 ASP 1920x1080 25p,30p,50i,60i 30

H.264 1920x1080 25p,30p,50p,60p,60i 30

MPEG-2 1920x1080 25p,30p,50i,60i 30

MPEG-4 ASP 1920x1080 25p,30p,50i,60i 30

H.264 1920x1080 25p,30p,50p,60p,60i 30

1920x1080i@field rate=50, 60Hz

1920x1080p@frame

MVC

MPEG-2 1920x1080 25p,30p,50i,60i 30

MPEG-4 ASP 1920x1080 25p,30p,50i,60i 30

H.264 1920x1080 25p,30p,50p,60p,60i 30

MVC

rate=24, 25,30Hz

1280x720p@frame

rate=50, 60Hz

1920x1080i @ field

rate=50, 60Hz

1920x1080p @ frame

rate=24, 25,30Hz

1280x720p @ frame

rate=50, 60Hz

Max.Frame Rate

(fps)

- 30

- 30

Max.Bit

Rate

(Mbps)

Audio codec

(L1&L2),

MPEG-1, 2, 2.5

L3, AAC/HE-

AAC (v1&v2),

DVD-PCM, AC3

MPEG-1
(L1&L2),

MPEG-1,2,2.5

L3, AAC/HE-

AAC (v1&v2),

AC3, E-AC3,

Dolby Pulse

MPEG-

1(L1&L2),

MPEG-1,2,2.5

L3, AAC/HE-

AAC (v1&v2),

AC3,E-AC3,
Dolby Pulse

MPEG-2 1920x1080 25p,30p,50i,60i 30 MPEG-1

.ts

.m2ts

.mts

.ts

.m2ts

.mts

.m4v M4V H.264 1920x1080 25p,30p,50p,60p,60i 30 AAC

.ism/

Manifest

.mpd

.mp4 MP4

AVCHD

AVCHD MVC

frag MP4

MPEG-4 ASP 1920x1080 25p,30p,50i,60i 30

H.264 1920x1080 25p,30p,50p,60p,60i 30

1920x1080i@field rate=50, 60Hz

1920x1080p@frame

rate=24, 25,30Hz

1280x720p @ frame

rate=50, 60Hz

H.264 1920x1080 25p,30p,50p,60p,60i 30

1920x1080i@field rate=50, 60Hz

1920x1080p@frame

MVC

MPEG-4 ASP 1920x1080 25p,30p,50i,60i 30

H.264 1920x1080 30

1920x1080i@field rate=50, 60Hz

MVC

rate=24, 25,30Hz

1280x720p @ frame

rate=50, 60Hz

1920x1080p@frame

rate=24, 25,30Hz

1280x720p @ frame

rate=50, 60Hz

- 30

- 30

- 30

(L1&L2),

MPEG-1,2,2.5

L3, AAC/HE-

AAC (v1&v2),

AC3,E-AC3,
Dolby Pulse

MPEG-1
(L1&L2),

MPEG-1,2,2.5

L3, AAC/HE-

AAC (v1&v2),

AC3,E-AC3,
Dolby Pulse

HE-AAC
(v1&v2), AC3,
E-AC3,WMA,

WMA-PRO

HE-AAC
(v1&v2), AC3,
E-AC3,WMA,

WMA-PRO

AAC/

AAC/

WMV9/VC1 1920x1080 30p, 60i 30

18

MPEG-4 ASP 1920x1080 25p,30p,50i,60i 30 MPEG-1

.mkv

.mk3d

MKV

USB Multimedia Formats

H.264 1920x1080 30

(L1&L2),

MPEG-1,2,2.5

L3, AAC/

HE-AAC

(v1&v2),

AC3,E-AC3,

WMA, WMA-

PRO

File

Extensions

.mp3 MP3 - - 48 384 MPEG-1, 2, 2.5 L3

.wma

.asf

.wma WMA Pro - - 96 768 WMA,WMA Pro

.wav(PC) LPCM - - 192 768 LPCM

.aif(mac)

.aiff(mac)

.aac
.mp4
.m4a

.pls

.m3u

.m4a M4A - - 48 1024

Container Video codec Maximum resolution

WMA

(V2 up to

V9.2)

LPCM - - 192 768 LPCM

AAC - - 48 1024

Playlists - - - - -

- - 48 192 WMA

Max.Frame Rate

(fps)

Max.Bit Rate

(Mbps)

Audio codec

AAC,HE-AAC

(v1&v2)

AAC,

HE-AAC (v1&v2)

USB Photo Formats

File

Extensions

Container Video codec Maximum resolution

Max.Frame

Rate (fps)

Max.Bit Rate

(Mbps)

Audio codec

baseline:
color mode = 444,

jpg/jpeg JPEG

bmp BMP

png PNG

gif GIF

size <=32768x16128
color mode = 422v,
size <= 16384x16128
color mode = other, not support

4096x3072_4bit,
2730x2500_8bit,
2048x1536_16bit,
1500x1200_32bit

4096x3072_4bit,
2730x2500_8bit,
2048x1536_16bit,
1500x1200_32bit

4096x3072_4bit,
2730x2500_8bit,
2048x1536_16bit,
1500x1200_32bit

- - -

- - -

- - -

- - -

NOTES:

• Sound or video may not work if the contents have a standard bit rate/frame rate above the compatible
Frame/sec listed in the table above.

• Video content with a Bit rate or Frame rate larger than the rate specied in the table above can cause

choppy video during playback.

19

7. Input mode

VGA Resolution:

Standard

Resolution

VGA 640 480

WVGA 720 400 70 Hz 33.75 MHz 16:9

SVGA 800

XGA 1024 768

WXGA 1280 768 60 Hz 79.5 MHz 5:3 Wide XGA
WXGA 1280 800 60 Hz 79.5 MHz 16:10 Wide XGA

SXGA 1280 960 60 Hz 108 MHz 4:3 Super XGA

SXGA 1280 1024 60 Hz 108 MHz 5:4 Super XGA
WXGA 1360 768 60 Hz 85.5 MHz 16:9 Wide XGA
WXGA 1366 768 60 Hz 85.5 MHz 16:9 Wide XGA

UXGA 1600 1200 60 Hz 162 MHz 4:3 Ultra XGA

HD1080 1920 1080 60 Hz 148.5 MHz 16:9 HD1080

Active Resolution

H Pixels V Lines

600 60 Hz 40 MHz
600 75 Hz 49.5 MHz

Refresh Rate Pixel Rate Aspect Ratio Stand for Mode

60 Hz 25.175 MHz

4:3 Video Graphic Array72 Hz 31.5 MHz

75 Hz 31.5 MHz

Wide Video Graphic

4:3 Super VGA

60 Hz 65 MHz
75 Hz 78.75 MHz

4:3

Extended Graphic

Array

Array

SDTV Resolution:

Standard

Resolution

480i

480p 59.94 Hz 27 MHz

576i

576p 50 Hz 27 MHz

Active Resolution

H Pixels V Lines

720 480

720 480

Refresh Rate Pixel Rate Aspect Ratio Stand for Mode

29.97 Hz 13.5 MHz

25 Hz 13.5 MHz

4:3

4:3

Modied NTSC

Standard

Modied PAL

Standard

HDTV Resolution:

Standard

Resolution

Active Resolution

Refresh Rate Pixel Rate Aspect Ratio Stand for Mode

H Pixels V Lines

50 Hz

720p 1280 720

74.25 MHz 16:9 Normally DVB Mode

60 Hz

1080i 1920 1080

25 Hz
30 Hz

74.25 MHz 16:9 Normally ATSC Mode

50 Hz

1080p 1920 1080

148.5 MHz 16:9 Normally ATSC Mode

60 Hz

• The PC text quality is optimum in HD 1080 mode (1920 x 1080, 60Hz).

• Your PC display screen might appear different depending on the manufacturer (and your particular version of Windows).

• Check your PC instruction book for information about connecting your PC to a display.

• If a ver tical and horizontal frequency-select mode exists, select 60Hz (ver tical) and 31.5KHz (horizontal). In some cases,

abnormal signals (such as stripes) might appear on the screen when the PC power is turned off (or if the PC is disconnected). If
so, press the [

• When horizontal synchronous signals seem irregular in RGB mode, check PC power saving mode or cable connections.

• The display settings table complies to the IBM/VESA standards, and based on the analog input.

• The DVI support mode is regarded as same to the PC support mode.

• The best timing for the ver tical frequency to each mode is 60Hz.

SOURCE] button to enter the video mode. Also, make sure that the PC is connected.

20

8. Cleaning and Troubleshooting

8.1. Cleaning

When Using the Display

• Do not bring your hands, face or objects close to the ventilation holes of the display. The top of the
display is usually very hot due to the high temperature of exhaust air being released through the
ventilation holes. Burns or personal injuries may occur if any body parts are brought too close. Placing
any object near the top of the display could also result in heat related damage to the object as well as
the display itself.

• Be sure to disconnect all cables before moving the display. Moving the display with its cables attached
may damage the cables and thus cause re or electric shock.

• Disconnect the power plug from the wall outlet as a safety precaution before carrying out any type of

cleaning or maintenance procedure.

Front Panel Cleaning Instructions

• The front of the display has been specially treated. Wipe the surface gently using only a cleaning cloth
or a soft, lint-free cloth.

• If the surface becomes dirty, soak a soft, lint-free cloth in a mild detergent solution. Wring the cloth to
remove excess liquid. Wipe the surface of the display to remove dirt. Then use a dry cloth of the same
type to dry.

• Do not scratch or hit the surface of the panel with ngers or hard objects of any kind.

• Do not use volatile substances such as insert sprays, solvents and thinners.

Cabinet Cleaning Instructions

• If the cabinet becomes dirty, wipe the cabinet with a soft, dry cloth.

• If the cabinet is extremely dirty, soak a lint-free cloth in a mild detergent solution. Wring the cloth to

remove as much moisture as possible. Wipe the cabinet. Use another dry cloth to wipe over until the
surface is dry.

• Do not allow any water or detergent to come into contact with the surface of the display. If water or
moisture gets inside the unit, operating problems, electrical and shock hazards may result.

• Do not scratch or hit the cabinet with ngers or hard objects of any kind.

• Do not use volatile substances such as insert sprays, solvents and thinners on the cabinet.

• Do not place anything made from rubber or PVC near the cabinet for any extended periods of time.

21

8.2. Troubleshooting

Symptom Possible Cause Remedy
No picture is displayed 1. The power cord is disconnected.

2. The main power switch on
the back of the display is not
switched on.

3. The selected input has no
connection.

4. The display is in standby mode.

Interference displayed on the
display or audible noise is
heard

Color is abnormal The signal cable is not connected

Picture is distorted with
abnormal patterns

Displayimagedoesn’tllup

the full size of the screen

Caused by surrounding electrical

appliances or uorescent lights.

properly.

1. The signal cable is not connected
properly.

2. The input signal is beyond the
capabilities of the display.

Zoom mode is not correctly set. Use the Zoom mode or Custom

1. Plug in the power cord.

2. Make sure the power switch is
switched on.

3. Connect a signal connection to
the display.

Move the display to another location
to see is the interference is reduced.

Make sure that the signal cable is

attached rmly to the back of the

display.

1. Make sure that the signal cable

is attached rmly.

2. Check the video signal source
to see if it is beyond the range
of the display. Please verify its

specications with this display’s
specication section.

zoom function in the Screen menu

to ne tune display geometry and

time frequency parameter.

Can hear sound, but no
picture

Can see picture but no sound
is heard

Some picture elements do not
light up

After-Images can still be
seen on the display after
the display is powered off.
(Examples of still pictures
include logos, video games,
computer images, and images
displayed in 4:3 normal mode)

Improperly connected source signal
cable.

1. Improperly connected source
signal cable.

2. Volume is turned all the way
down.

3. [MUTE] is turned on.

4. No external speaker connected.

Some pixels of the display may not
turn on.

A still picture is displayed for an
over extended period of time

Make sure that both video inputs
and sound inputs are correctly
connected.

1. Make sure that both video inputs
and sound inputs are correctly
connected.

2. Press [VOL +] or [VOL -] button
to hear sound.

3. Switch MUTE off by using the
[MUTE] button.

4. Connect external speakers and
adjust the volume to a suitable
level.

This display is manufactured using
an extremely high level of precision
technology: however, sometimes
some pixels of the display may not
display. This is not a malfunction.

Do not allow a still image to be
displayed for an extended period of
time as this can cause a permanent
after-image to remain on the
display.

22

9. Technical Specifications

9.1. CDE3205-EP

Display:

Item Specications

Screen Size (Active Area) 698.4(H) x 392.85(V)
Aspect Ratio 16:9
Number of Pixels 1920 (H) x 1080 (V)
Pixel Pitch 0.36375(H) x 0.36375(V)
Displayable Colors 16.7M
Brightness 350 cd/m²
Contrast Ratio (Typical) 1200:1
Viewing Angle 178 degrees

In/Out Terminals:

Item Specications

Speaker Output Internal Speakers 10W (L) + 10W (R) [RMS]/8Ω, 1 Way 1 Speaker System

82 dB/W/M/160 Hz ~ 13 KHz
Audio Output 3.5mm jack x 1 0.5V [rms] (Normal) / 2 Channel (L+R)
Audio Input 3.5 mm Stereo × 1

RCA Jack × 2

RS232C Input/
Output

LAN RJ-45 Jack × 1 (8 pin) 10/100 LAN Port
HDMI Input HDMI Jack × 1

DVI-D Input DVI-D jack Digital RGB:TMDS (Video)
VGA Input D-Sub Jack x 1

Component Input RCA Jack x 3 Y: 1V [p-p] (75Ω), Pb: 0.7V [p-p] (75Ω), Pr : 0.7V [p-p] (75Ω)

Video Input RCA x 1 (Share with

2.5mm jack x 2 RS232C in/RS232C out

(Type A) (19 pin)

(15 pin)

Component_Y)

0.5V [rms] (Normal) / 2 Channel (L+R)

Digital RGB: TMDS (Video + Audio)

MAX: Video: 720p, 1080p, 1920 × 1080/60 Hz (WUXGA)

Audio: 48 KHz / 2 Channel (L+R)

Supports LPCM only

Analog RGB: 0.7V [p-p] (75Ω), H/CS/V:TTL (2.2kΩ),

SOG: 1V [p-p] (75Ω)

MAX: 720p, 1080p, 1920 x 1080/60 Hz (WUXGA)

MAX: 480i, 576i, 480p, 576p, 720p, 1080i, 1080p

Composite 1V [p-p] (75Ω)

General:

Item Specications

Power Supply AC 100 - 240V, 50 - 60Hz, 1.5A
Power Consumption (Max) 81W
Power Consumption (typ.) 57W
Power Consumption (Standby & Off) <0.5 W (RS232 in active)
Dimensions (With Stand) [W x H x D] 726.5mmx462.93mmx239.8mm
Dimensions (Without Stand) [W x H x D] 726.5mmx425.4mmx63.6mm
Weight (With Stand) 6.67 Kg
Weight (Without Stand) 5.2 Kg
Gross Weight (Without Stand) 7.8 Kg

23

Environmental Condition:

Item Specications

Temperature

Humidity

Altitude

Operational 0 ~ 40°C
Storage -20 ~ 60°C
Operational 20 ~ 80% RH (No condensation)
Storage 5 ~ 95% RH (No condensation)
Operational 0 ~ 3,000 m
Storage 0 ~ 9,000 m

Internal Speaker:

Item Specications

Type 1 Way 1 Speaker
Input 10 W (RMS)
Impedance 16Ω
Output Sound Pressure
Frequency Response

82 dB/W/M
160 Hz ~ 13 KHz

24

10. RS232 Protocol

10.1. Introduction

This document describes the hardware interface spec and software protocols of RS232 interface
communication between ViewSonic Commercial TV / Digital Signage and PC or other control unit with
RS232 protocol.

The protocol contains three sections command:

• Set-Function

• Get-Function

• Remote control pass-through mode

* In the document below, “PC” represents all the control units that can send or receive the RS232 protocol
command.

10.2. Description

10.2.1. Hardware specification

Viewsonic TV communication port on the rear side:
(1) Connector type: DSUB 9-Pin Male
(2) Pin Assignment

Male DSUB 9-Pin
(outside view)

[Special case]3.5mm barrel
connector

10.2.2. Communication Setting

- Baud Rate Select: 9600bps (xed)

- Data bits: 8 bits (xed)

- Parity: None (xed)

- Stop Bits: 1 (xed)

Pin # Signal Remark

1 NC
2 RXD Input to Commercial TV or DS
3 TXD Output from Commercial TV or DS
4 NC
5 GND
6 NC
7 NC
8 NC
9 NC
frame GND

* Use of crossover (null modem) cable required for use with PC

Pin # Signal Remark

Tip TXD Output from Commercial TV or DS
Ring RXD Input to Commercial TV or DS
Sleeve GND

10.2.3. Command Message Reference

PC sends to Monitor command packet followed by “CR”. Every time PC sends control command to the
Monitor, the Monitor shall respond as follows:

1. If the message is received correctly it will send “+” (02Bh) followed by “CR” (00Dh)

2. If the message is received incorrectly it will send “-” (02Dh) followed by “CR” (00Dh)

25

10.3. Protocol

10.3.1. Set-Function Listing

The PC can control the TV/DS for specic actions. The Set-Function command allows you to control the TV/

DS behavior in a remote site through the RS232 port. The Set-Function packet format consists of 9 bytes.

Set-Function description:
Length: Total Byte of Message excluding “CR”.
TV/DS ID Identication for each of TV/DS (01~98; default is 01)

If we want to set all TV/DS settings, use the TV/DS ID “99”, and it will not have Reply
command on this function.
The TV/DS ID can be set via the OSD menu for each TV/DS set.

Command Type Identify command type,

“s” (0x73h) : Set Command
“+” (0x2Bh) : Valid command Reply
“-“ (0x2Dh) : Invalid command Reply

Command: Function command code: One byte ASCII code.
Value[1~3]: Three bytes ASCII that denes the value.
CR 0x0D

Set-Function format
Send: (Command Type=”s”)

Name Length ID

Byte Count 1 Byte 2 Byte 1 Byte 1 Byte 1 Byte 1 Byte 1 Byte 1 Byte

Bytes order 1 2~3 4 5 6 7 8 9

NOTE: For VT2405LED-1 and VT3205LED, the set “Power on” command is the exception

Reply: (Command Type=”+” or “-”)

Name Length ID

Byte Count 1 Byte 2 Byte 1 Byte 1 Byte

Bytes order 1 2~3 4 5

NOTE:

1. The reply for “Power on” command is the exception for VT2405LED-1 and VT3205LED.
It’s 0x322B0D ( 2+<CR>).

2. When PC applies command to all displays (ID=99), only the #1 set needs to reply by the name of ID=1.

Example1: Set Brightness as 76 for TV-02 and this command is valid
Send (Hex Format)

Name Length ID

Hex

0x38

0x30
0x32

Command

Type

Command

Type

Command

Type

0x73 0x24 0x30 0x37 0x36 0x0D

Command Value1 Value2 Value3 CR

CR

Command Value1 Value2 Value3 CR

Reply (Hex Format)

Name Length ID

Hex

0x34

0x30
0x32

Command

Type

0x2B 0x0D

CR

26

Example2: Set Brightness as 176 for TV-02 and this command is NOT valid Send (Hex Format)

Name Length ID

Hex

0x38

0x30
0x32

Command

Type

Command Value1 Value2 Value3 CR

0x73 0x24 0x31 0x37 0x36 0x0D

Reply (Hex Format)

Name Length ID

Hex

0x34

0x30
0x32

Command

Type

0x2D 0x0D

CR

Set function table:

Set Function Length ID Command

Type

Code (ASCII) Code (Hex) (Three ASCII bytes)

Command Value Range Comments

Power on/off
(standby)

Input Select 8 s “ 22 000 : TV

Contrast 8 s # 23 000 ~ 100

Brightness 8 s $ 24 000 ~ 100

Sharpness 8 s % 25 000 ~ 100

Color 8 s & 26 000 ~ 100

Tint 8 s ‘ 27 000 ~ 100

Color Mode 8 s ) 29 000 : Normal

Bass 8 s . 2E 000 ~ 100 Sets Bass value

8 s ! 21 000: STBY

001: ON

001 : AV
002 : S-Video
003 : YPbPr
004 : HDMI
014 : HDMI2
024 : HDMI3
005 : DVI
006 : VGA1(PC)
016 : VGA2
007 : OPS
008 : Internal Mem
009 : DP

001 : Warm
002 : Cold
003 : Personal

Controlled power
status: ON or Standby

1. No need for USB

2. For the case of two
more same sources,
the 2nd digital is
used to indicate the
extension.

Treble 8 s / 2F 000 ~ 100 Sets Treble value

Balance 8 s 0 30 000 ~ 100 Sets Balance position

Picture Size 8 s 1 31 000 : FULL

001 : NORMAL
002 : CUSTOM
003 : DYNAMIC
004 : REAL

OSD Language 8 s 2 32 000 : English

001 : French
002 : Spanish

Power Lock 8 s 4 34 000 : Unlock

001 : Lock

Volume 8 s 5 35 000 ~ 100

900 : Volume down (-1)
901 : Volume up (+1)

27

Mute 8 s 6 36 000: OFF

001: ON (mute)

Button Lock 8 s 8 38 000 : Unlock

001 : Lock

Menu Lock 8 s > 3E 000 : Unlock

001 : Lock

Key Pad 8 s A 41 000 : UP

001 : DOWN
002 : LEFT
003 : RIGHT
004 : ENTER
005 : INPUT
006 : MENU/EXIT

Remote Control 8 s B 42 000: Disable

Disable: RCU has no
effect on Monotor.

001: Enable

Enabled: RCU controls
the Monitor. This is the
power up default on the
Monitor.

002: Pass through

Pass through: RCU
has no effect on
Monitor and all RCU
command codes are
transmitted to PC via
the RS232 port.

Date 8 s V 56 0xx: Year

1xx: Month+Day

For specific models
only

(See example in Note)

Tiling-Mode 8 s P 50 000: OFF

(for DS)

001: ON

Tiling­Compensation

8 s Q 51 000: OFF

001: ON

(for DS)
Bezel width

compensation

Tiling-H by V
Monitors

8 s R 52 01x~09x: H

0x1~0x9: V

(for DS)

nd

digital for H

1. 2
monitors

rd

digital for V

2. 3
monitors

Tiling-Position 8 s S 53 001~025 (for DS)

Copy the screen of
Position# to identified
display

Time 8 s W 57 0xx: Hour+Min

10x: Sec

For specific models
only

(See example in Note)

Factory reset 8 s ~ 7E 0 Rests Monitor to

factory setting

28

10.3.2. Get-Function Listing

The PC can interrogate the TV/DS for specic information. The Get-Function packet format consists of 9

bytes which is similar to the Set-Function packet structure. Note that the “Value” byte is always = 000

Get-Function description:
Length: Total Byte of Message excluding “CR”.
TV/DS ID Identication for each of TV/DS (01~98; default is 01).

Command Type Identify command type,

“g” (0x67h) : Get Command
“r” (0x72h) : Valid command Reply
“-“ (0x2Dh) : Invalid command Reply

Command: Function command code: One byte ASCII code.
Value[1~3]: Three bytes ASCII that denes the value.
CR 0x0D

Get-Function format
Send: (Command Type=”g”)

Name Length ID

Byte Count 1 Byte 2 Byte 1 Byte 1 Byte 1 Byte 1 Byte 1 Byte 1 Byte

Bytes order 1 2~3 4 5 6 7 8 9

Command

Type

Command Value1 Value2 Value3 CR

NOTE: “Power STBY status” is the exception for VT2405LED-1 and VT3205LED.

Reply: (Command Type=”r” or “-”)

If the Command is valid, Command Type =”r”

Name Length ID

Byte Count 1 Byte 2 Byte 1 Byte 1 Byte 1 Byte 1 Byte 1 Byte 1 Byte

Bytes order 1 2~3 4 5 6 7 8 9

NOTE: The reply for “Power STBY status” command is the exception for VT2405LED-1 and V3205LED. It’s

0x36 72 6C 30 30 30 0D ( 6rl000<CR>).

If the Command is Not valid, Command Type=”-“

Name Length ID

Byte Count 1 Byte 2 Byte 1 Byte 1 Byte

Bytes order 1 2~3 4 5

Example1: Get Brightness from TV-05 and this comm and is valid. The Brightness value is 67.
Send (Hex Format)

Name Length ID

Hex

0x38

0x30
0x35

Command

Type

Command

Type

Command

Type

0x67 0x62 0x30 0x30 0x30 0x0D

Command Value1 Value2 Value3 CR

CR

Command Value1 Value2 Value3 CR

29

Reply (Hex Format)

Name Length ID

Hex

Example2: Get Brightness from TV-05, but the Brightness command ID is error and it is NOT in the
command table.

Send (Hex Format)

Name Length ID

Hex

Reply (Hex Format)

Name Length ID

Hex

0x38

0x38

0x34

0x30
0x35

0x30
0x35

0x30
0x35

Command

Type

0x72 0x62 0x30 0x36 0x37 0x0D

Command

Type

0x67 0XD3 0x30 0x30 0x30 0x0D

Command

Type

0x2D 0x0D

Command Value1 Value2 Value3 CR

Command Value1 Value2 Value3 CR

CR

30

Get function table:

Get Function Length ID Command

Type

Code (ASCII) Code (Hex) (Three ASCII bytes)

Get-Contrast 8 g a 61 000 ~ 100 Gets Contrast value
Get-Brightness 8 g b 62 000 ~ 100 Gets Brightness value
Get-Sharpness 8 g c 63 000 ~ 100 Gets Sharpness value

Get-Color 8 g d 64 000 ~ 100 Gets Color value

Get-Tint 8 g e 65 000 ~ 100 Gets Tint value

Get-Volume 8 g f 66 000 ~ 100 Gets Volume value

Command Value Range Comments

Get-Mute 8 g g 67 000: OFF (unmuted)

001: ON (muted)

Get-Input select 8 g j 6A 000~ See Set-function table

Get-Power
status : ON/
STBY

Get-Remote
control

Get-Power Lock 8 g o 6F 000 : Unlock

Get-Button Lock 8 g p 70 000 : Unlock

Get-Menu Lock 8 g q 71 000 : Unlock

Get-Tiling Mode 8 g v 76 000: OFF

Get-Tiling
Compensation

Get-Tiling H by V
monitors

Get-Tiling
position

Get-ACK 8 g z 7A 000 This command is

Get-Thermal 8 g 0 30 000~100:

Get-Power on/
off log

Get-Date 8 g 2 32 000

Get- Time 8 g 3 33 000

8 g l 6C 000: STBY

001: ON

8 g n 6E 000 : Disable

001 : Enable
002 : Pass through

001 : Lock

001 : Lock

001 : Lock

001: ON

8 g w 77 000: OFF

001: ON

8 g x 78 01x~09x: H monitors

0x1~0x9: V monitors

8 g y 79 000: OFF

001~025

0~+100 deg C

-01~-99:

-1~-99 deg C

8 g 1 31 000

(See below note)

(See the Set-Date
command)

(See the Set-Time
command)

Gets Mute ON/OFF
status

(for DS)

(for DS)
Bezel width
compensation

(for DS)

nd

1. 2

digital for H

monitors

2. 3rd digital for V

monitors

(for DS)
Copy the screen of
Position# to identified
display

used to test the
communication link.

For specific models
only

For specific models
only

For specific models
only

For specific models
only

31

10.3.3. Remote Control Pass-through mode

When the PC sets the TV/DS to Remote Control Pass through mode, the TV/DS will send a 7-byte packet
(followed by “CR”) in response to RCU button activation. Note, that in this mode the RCU shall have no
effect on the TV/DS function. For example: “Volume+” will not change the volume in the LCD but only sends
“Volume+” code to PC over the RS232 port.

IR Pass Through-Function format
Reply: (Command Type=”p”)

Name Length ID

Byte Count 1 Byte 2 Byte 1 Byte 1 Byte 1 Byte 1 Byte
Bytes order 1 2~3 4 5 6 7

Example1: Remote Control pass-through when “VOL+” key is pressed for TV-05 Send (Hex Format)

Name Length ID

Hex

0x36

0x30
0x35

Command

Type

Command

Type

0x70 0x31 0x30 0x0D

RCU Code1

(MSB)

Command Value1 CR

RCU Code2

(LSB)

CR

32

Key Code (HEX)

1 01
2 02
3 03
4 04
5 05
6 06
7 07
8 08
9 09
0 0A

- 0B
RECALL (LAST) 0C
INFO (DISPLAY) 0D

0E
ASPECT (ZOOM, SIZE) 0F
VOLUME UP (+) 10
VOLUME DOWN (-) 11
MUTE 12
CHANNEL/PAGE UP (+)/
BRIGHTNESS+
CHANNEL/PAGE DOWN (-)/
BRIGHTNESS­POWER 15
SOURCES (INPUTS) 16

SLEEP 19
MENU 1A
UP 1B
DOWN 1C
LEFT (-) 1D
RIGHT (+) 1E
OK (ENTER, SET) 1F
EXIT 20

RED ■ (F1) 2C
GREEN ■ (F2) 2D
YELLOW ■ (F3) 2E
BLUE ■ (F4) 2F

13

14

17
18

21
22
23
24
25
26
27
28

29
2A
2B

33

NOTE:

1. This IR-pass-through code is different from the RCU key code.

2. Special control sequence for POWER key under IR-pass through mode.
2-1. When TV/DS is OFF and receives the IR POWER code: TV/DS will turn itself on, then forward

the POWER code to the host via RS232.

2-2. When TV/DS is ON and receives the IR POWER code: TV/DS will forward the POWER code to

the host via RS232, then turn off itself.

2-3. When SET-POWER LOCK is enabled, the TV/DS will not respond to POWER key pressing.

3. The VOLUME UP and VOLUME DOWN code will repeatedly output when you press and hold the keys.

34

11. Other Information

Customer Support

For technical support or product service, see the table below or contact your reseller.

NOTE: You will need the product serial number.

Country/Region Website

Australia
New Zealand

Canada www.viewsonic.com T= 1-866-463-4775 [e-mail]

Europe www.viewsoniceurope.com http://www.viewsoniceurope.com/eu/support/call-desk/

Hong Kong www.hk.viewsonic.com T= 852 3102 2900 [e-mail]

India www.in.viewsonic.com T= 1800 419 0959 [e-mail]

Korea ap.viewsonic.com/kr/ T= 080 333 2131 [e-mail]

Latin America www.viewsonic.com/la/

Macau www.hk.viewsonic.com T= 853 2840 3687 [e-mail]

Middle East ap.viewsonic.com/me/ Contact your reseller [e-mail]

www.viewsonic.com.au

T = Telephone
C = CHAT ONLINE

AUS= 1800 880 818
NZ= 0800 008 822

C= http://www.viewsonic.com/la/
soporte/servicio-tecnico

Email

[e-mail]

[e-mail]

Puerto Rico &
Virgin Islands

Singapore/
Malaysia/
Thailand

South Africa ap.viewsonic.com/za/ Contact your reseller [e-mail]

United States www.viewsonic.com T= 1-800-688-6688 [e-mail]

www.viewsonic.com

www.viewsonic.com.sg T= 65 6461 6044 [e-mail]

T= 1-800-688-6688 (English)
C= http://www.viewsonic.com/la/
soporte/servicio-tecnico

[e-mail]
[e-mail]

35

Limited Warranty

ViewSonic® LCD Commercial Display

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship, under normal use,
during the warranty period. If a product proves to be defective in material or workmanship during the war­ranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement
product or parts may include remanufactured or refurbished parts or components.

Who the warranty protects:

This warranty is valid only for the rst consumer purchaser.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modified or removed.

2. Damage, deterioration or malfunction resulting from:
a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product

modification, or failure to follow instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Removal or installation of the product.
d. Causes external to the product, such as electrical power fluctuations or failure.
e. Use of supplies or parts not meeting ViewSonic’s specifications.
f. Normal wear and tear.
g. Any other cause which does not relate to a product defect.

3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static
image is displayed on the product for an extended period of time.

4. Removal, installation, one way transportation, insurance, and set-up service charges.

How to get service:

1. For information about receiving service under warranty, contact ViewSonic Customer Support (Please
refer to Customer Support page). You will need to provide your product’s serial number.

2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your
name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service
center or ViewSonic.

4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.

4.3: ViewSonic LCD Commercial Display Page 1 of 2 CD_LW01 Rev. 1a 02-11-09

36

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein including

the implied warranty of merchantability and tness for a particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be li­able for:

1. Damage to other property caused by any defects in the product, damages based upon inconvenience,
loss of use of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill,
interference with business relationships, or other commercial loss, even if advised of the possibility of
such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

4. Repair or attempted repair by anyone not authorized by ViewSonic.

Effect of state law:

This warranty gives you specic legal rights, and you may also have other rights which vary from state to

state. Some states do not allow limitations on implied warranties and/or do not allow the exclusion of inci­dental or consequential damages, so the above limitations and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact
ViewSonic or your local ViewSonic dealer.
The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is subject
to the terms and conditions of the Maintenance Guarantee Card.
For users in Europe and Russia, full details of warranty provided can be found in www.viewsoniceurope.com
under Support/Warranty Information.

4.3: ViewSonic LCD Commercial Display Page 2 of 2 CD_LW01 Rev. 1a 02-11-09

37

Mexico Limited Warranty

ViewSonic® LCD Commercial Display

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the
warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic
will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include re­manufactured or refurbished parts or components.

Who the warranty protects:

This warranty is valid only for the rst consumer purchaser.

What the warranty does not cover:

1. Any product on which the serial number has been defaced, modified or removed.

2. Damage, deterioration or malfunction resulting from:

a. Accident, misuse, neglect, fire, water, lightning, or other acts of nature, unauthorized product modification, or

failure to follow instructions supplied with the product.
b. Any damage of the product due to shipment.
c. Removal or installation of the product.
d. Causes external to the product, such as electrical power fluctuations or failure.
e. Use of supplies or parts not meeting ViewSonic’s specifications.
f. Normal wear and tear.
g. Any other cause which does not relate to a product defect.

3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is
displayed on the product for an extended period of time.

4. Removal, installation, one way transportation, insurance, and set-up service charges.

How to get service:

For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the at­tached Customer Support page). You will need to provide your product’s serial number, so please record the product
information in the space provided below on your purchase for your future use. Please retain your receipt of proof of
purchase to support your warranty claim.

For Your Records
Product Name: _______________________ Model Number: ____________________________________
Document Number: ___________________ Serial Number: ____________________________________
Purchase Date: ______________________ Extended Warranty Purchase? ____________________(Y/N)
If so, what date does warranty expire? __________________

1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your
address, (d) a description of the problem, and (e) the serial number of the product.

2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.

3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein including the im-

plied warranty of merchantability and tness for a particular purpose.

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use
of the product, loss of time, loss of profits, loss of business opportunity, loss of goodwill, interference with business
relationships, or other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

4. Repair or attempted repair by anyone not authorized by ViewSonic.

5.

6.

7.

4.3: ViewSonic Mexico Limited Warranty Page 1 of 2 CD_LW02 Rev. 1A 06-25-07

38

Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:

Name, address, of manufacturer and importers:

México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas,
Col. San Fernando Huixquilucan, Estado de México
Tel: [phone]
http://www.viewsonic.com/la/soporte/index.htm

NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004

Hermosillo:

Distribuciones y Servicios Computacionales SA de CV.
Calle Juarez 284 local 2
Col. Bugambilias C.P: 83140
Tel: [phone]
E-Mail: [e-mail]

Puebla, Pue. (Matriz):

RENTA Y DATOS, S.A. DE C.V. Domicilio:
29 SUR 721 COL. LA PAZ
72160 PUEBLA, PUE.
Tel: [phone] CON 10 LINEAS
E-Mail: [e-mail]

Chihuahua

Soluciones Globales en Computación
C. Magisterio # 3321 Col. Magisterial
Chihuahua, Chih.
Tel: [phone]
E-Mail: [e-mail]

Distrito Federal:

QPLUS, S.A. de C.V.
Av. Coyoacán 931
Col. Del Valle 03100, México, D.F.
Tel: [phone]
E-Mail : [e-mail]

Guerrero Acapulco

GS Computación (Grupo Sesicomp)
Progreso #6-A, Colo Centro
39300 Acapulco, Guerrero
Tel: [phone]

MERIDA:

ELECTROSER
Av Reforma No. 403Gx39 y 41
Mérida, Yucatán, México CP97000
Tel: [phone]
E-Mail: [e-mail]

Tijuana:

STD
Av Ferrocarril Sonora #3780 L-C
Col 20 de Noviembre
Tijuana, Mexico

Villahermosa:

Compumantenimietnos Garantizados, S.A. de C.V.
AV. GREGORIO MENDEZ #1504
COL, FLORIDA C.P. 86040
Tel: [phone]
E-Mail: [e-mail]

Veracruz, Ver.:

CONEXION Y DESARROLLO, S.A DE C.V.
Av. Americas # 419
ENTRE PINZÓN Y ALVARADO
Fracc. Reforma C.P. 91919
Tel: [phone]
E-Mail: [e-mail]

Cuernavaca

Compusupport de Cuernavaca SA de CV
Francisco Leyva # 178 Col. Miguel Hidalgo
C.P. 62040, Cuernavaca Morelos
Tel: [phone]
E-Mail: [e-mail]

Guadalajara, Jal.:

SERVICRECE, S.A. de C.V.
Av. Niños Héroes # 2281
Col. Arcos Sur, Sector Juárez
44170, Guadalajara, Jalisco
Tel: [phone]
E-Mail: [e-mail]

Monterrey:

Global Product Services
Mar Caribe # 1987, Esquina con Golfo Pérsico
Fracc. Bernardo Reyes, CP 64280
Monterrey N.L. México
Tel: [phone]
E-Mail: [e-mail]

Oaxaca, Oax.:

CENTRO DE DISTRIBUCION Y
SERVICIO, S.A. de C.V.
Murguía # 708 P.A., Col. Centro, 68000, Oaxaca
Tel: [phone]
Fax: [phone]
E-Mail. [e-mail]

FOR USA SUPPORT:

ViewSonic Corporation
10 Pointe Dr. Suite 200. Brea, CA. 92821 UY.S.A
Tel: [phone]
E-Mail: http://www.viewsonic.com

4.3: ViewSonic Mexico Limited Warranty Page 2 of 2 CD_LW02 Rev. 1A 06-25-07

39