ViewSonic CD4233 User Guide

Download

Page 1

CD4233

- User Guide

LCD Commercial Display

- Guide de l’utilisateur

- Guía del usuario

- Bedienungsanleitung

3\ɤɨɜɨɞɫɬɜɨɩɨɥɶɡɨɜɚɬɟɥɹ

ĮġٺҢЙы

Model No.: VS13510

Page 2

Declaration of RoHS Compliance

This product has been designed and manufactured in compliance with Directive 2002/95/ EC of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

Lead (Pb) 0.1% < 0.1%

Mercury (Hg) 0.1% < 0.1%

Cadmium (Cd) 0.01% < 0.01%

Hexavalent Chromium (Cr6+) 0.1% < 0.1%

Polybrominated biphenyls (PBB) 0.1% < 0.1%

Polybrominated diphenyl ethers (PBDE) 0.1% < 0.1%

Certain components of products as stated above are exempted under the Annex of the RoHS Directives as noted below: Examples of exempted components are:

Proposed Maximum

Actual Concentration

Concentration

0HUFXU\LQFRPSDFWÀXRUHVFHQWODPSVQRWH[FHHGLQJPJSHUODPSDQGLQRWKHUODPSV

QRWVSHFL¿FDOO\PHQWLRQHGLQWKH$QQH[RI5R+6'LUHFWLYH

/HDGLQJODVVRIFDWKRGHUD\WXEHVHOHFWURQLFFRPSRQHQWVÀXRUHVFHQWWXEHVDQG

electronic ceramic parts (e.g. piezoelectronic devices).

3. Lead in high temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).

4. Lead as an allotting element in steel containing up to 0.35% lead by weight, aluminium containing up to 0.4% lead by weight and as a cooper alloy containing up to 4% lead by weight.

ViewSonic CD4233

Page 3

Copyright© ViewSonic Corporation, 2010. All rights reserved. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. ENERGY STAR®is a registered trademark of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR the ENERGY STAR Disclaimer:ViewSonic Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product. In the interest of continuing product improvement, ViewSonic Corporation reserves the right

WRFKDQJHSURGXFWVSHFL¿FDWLRQVZLWKRXWQRWLFH,QIRUPDWLRQLQWKLVGRFXPHQWPD\FKDQJH

without notice. No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic Corporation.

partner, ViewSonic Corporation has determined that this product meets

JXLGHOLQHVIRUHQHUJ\HI¿FLHQF\

Product Registration

To meet your future needs, and to receive any additional product information as it becomes available, please register your product on the Internet at: www.viewsonic.com.

For Your Records

Product Name:

Model Number:

Document Number:

Serial Number:

Purchase Date:

CD4233

ViewSonic 42” LCD Commercial Display

VS13510

CD4233_UG_ENG Rev. 1A 04-27-10

______________________________

Product disposal at end of product life

ViewSonic is concerned about the preservation of our environment. Please dispose of this product properly at the end of its useful life. Your local waste disposal company may provide information about proper disposal. The lamp in this product contains mercury. Please dispose of properly in accordance with environmental laws of your location.

ViewSonic CD4233

Page 4

CONTENTS

———————————————————————————————————————————————

SAFETY INSTRUCTIONS...............................................................................................................3

Package Contents..........................................................................................................................9

Parts Name and Functions..........................................................................................................10

Control Panel...........................................................................................................................................................10

Terminal Panel ......................................................................................................................................................... 11

Remote Control .......................................................................................................................................................12

Operating Range for the Remote Control................................................................................................................13

Handling the remote control ....................................................................................................................................13

Setup Procedure ..........................................................................................................................14

How to Mount and Attach Feet to the LCD Monitor...................................................................16

Connectivity .................................................................................................................................19

Connectivity Diagram ..............................................................................................................................................19

Connecting to a Personal Computer .......................................................................................................................20

Connecting to a Digital Interface Equipment...........................................................................................................21

Connecting to a DVD Player....................................................................................................................................22

Connecting to a Stereo Amplifier.............................................................................................................................23

Connecting to a display mounted PC ......................................................................................................................23

Basic Operation ...........................................................................................................................24

Power ON and OFF Modes.....................................................................................................................................24

Power Indicator........................................................................................................................................................25

Using Power Management ......................................................................................................................................25

Display Signal of Video Source Setting to [VIDEO].................................................................................................25

Picture Size..............................................................................................................................................................25

Smart Picture Mode.................................................................................................................................................26

Audio Source Switching...........................................................................................................................................26

Control Lock Mode ..................................................................................................................................................26

OSD Information......................................................................................................................................................26

OSD (On-Screen-Display) Controls ............................................................................................27

PICTURE.................................................................................................................................................................28

SCREEN..................................................................................................................................................................30

AUDIO .....................................................................................................................................................................32

PIP (PICTURE IN PICTURE) ..................................................................................................................................33

CONFIGURATION 1 ................................................................................................................................................34

CONFIGURATION 2 ................................................................................................................................................35

ADVANCED OPTION ..............................................................................................................................................36

NOTE.......................................................................................................................................................................38

Features........................................................................................................................................40

Troubleshooting...........................................................................................................................41

Specifications...............................................................................................................................43

ViewSonic CD4233

Page 5

SAFETY INSTRUCTIONS

WARNINGS AND PRECAUTIONS

KNOW THESE SAFETY SYMBOLS

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.



This symbol alerts you that important literature concerning operation and maintenance has been included with this product.

Caution: FCC/CSA regulations state that any unauthorized changes or modifications to this equipment may void the user’s authority to operate it.

Caution: To prevent electric shock, match the wide blade of plug to the wide slot, and fully insert the plug. Attention: Pour éviter les chocs électriques, introduire la lame la plus large de la fiche dans la bome correspondante de la prise et

pousser jusqu’au fond.

TO PREVENT DAMAGE WHICH MAY RESULT IN FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

The Socket-outlet shall be installed near the apparatus and shall be easily accessible.

Read and follow these instructions when connecting and using your computer monitor:

z Unplug the monitor if you are not going to use it for an extensive period of time.

z Unplug the monitor if you need to clean it with a slightly damp cloth. The screen many be wiped with a dry cloth

when the power is off. However, never use alcohol, solvents or ammonia-based liquids.

z Consult a service technician if the monitor does not operate normally when you have followed the instructions in

this manual.

z The casing cover should be opened only by qualified service personnel.

z Keep the monitor out of direct sunlight and away from stoves or any other heat source.

z Remove any object that could fall into the vents or prevent proper cooling of the monitor’s electronics.

z Do not block the ventilation holes on the cabinet.

z Keep the monitor dry. To avoid electric shock, do not expose it to rain or excessive moisture.

z If turning off the monitor by detaching power cable or DC power cord, wait for 6 seconds before attach the power

cable or DC power cord for normal operation.

z To avoid the risk of shock or permanent damage to the set do not expose the monitor to rain or excessive

moisture.

z When positioning the monitor, make sure the power plug and outlet are easily accessible. z IMPORTANT: Always activate a screen saver program during your application. If a still image in high contrast

remains on the screen for an extended period of time, it may leave an ‘after-image’ or ‘ghost image’ on the front of the screen. This is a well-known phenomenon that is caused by the shortcomings inherent in the LCD technology. In most cases the afterimage will disappear gradually over a period of time after the power has been switched off. Be aware that the after-image symptom cannot be repaired and is not covered under warranty.

ViewSonic CD4233

Page 6

REGULATORY INFORMATION

CE DECLARATION OF CONFORMITY

MMD declare under our responsibility that the product is in conformity with the following standards

• EN60950-1:2006+A11:2009 (Safety requirement of Information Technology Equipment)

• EN55022:2006+A1:2007 (Radio Disturbance requirement of Information Technology Equipment)

• EN55024:1998+A1:2001+A2:2003 (Immunity requirement of Information Technology Equipment)

• EN6100-3-2: 2006 (Limits for Harmonic Current Emission)

• EN6100-3-3:1995+A1:2001+A2:2005 (Limitation of Voltage Fluctuation and Flicker) following provisions of directives applicable

• 2006/95/EC (Low Voltage Directive)

• 2004/108/EC (EMC Directive)

• 93/68/EEC (Amendment of EMC and Low Voltage Directive) and is produced by a manufacturing organization on ISO9000 level.

FEDERAL COMMUNICATIONS COMMISSION (FCC) NOTICE (U.S. Only)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated In a commercial environment. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual, may cause harmful interference to radio

communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

Changes or mod

operate the equipment.

Use only RF shielded cable that was supplied with the monitor when connecting this monitor to a computer device.

To prevent damage which may result in fire or shock hazard, do not expose this appliance to rain or excessive moisture.

THIS CLASS B DIGITAL APPARATUS MEETS ALL REQUIREMENTS OF THE CANADIAN INTERFERENCE- CAUSING EQUIPMENT REGULATIONS.

his device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device

T may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

ifications not expressly approved by the party responsible for compliance could void the user’s authority to



ViewSonic CD4233

Page 7

POLISH CENTER FOR TESTING AND CERTIFICATION NOTICE

The equipment should draw power from a socket with an attached protection circuit (a three-prong socket). All equipment that works together (computer, monitor, printer, and so on) should have the same power supply source.

The phasing conductor of the room’s electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A).

To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and easily accessible.

A protection mark “B” confirms that the equipment is in compliance with the protection usage requirements of standards PN-93/T42107 and PN-89/E-06251.

     

ViewSonic CD4233

Page 8

INFORMATION FOR UK ONLY

WARNING - THIS APPLIANCE MUST BE EARTHED.

Important:

This apparatus is supplied with an approved moulded 13A plug. To change a fuse in this type of plug proceed as follows:

1. Remove fuse cover and fuse.

2. Fit new fuse which should be a BS 1362 5A,A.S.T.A. or BSI approved type.

3. Refit the fuse cover.

If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place.

If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A.

Note: The severed plug must be destroyed to avoid a possible shock hazard should it be inserted into a 13A socket elsewhere.

How to connect a plug

The wires in the mains lead are coloured in accordance with the following code: BLUE - “NEUTRAL” (“N”) BROWN - “LIVE” (“L”) GREEN & YELLOW - “EARTH” (“E”)

1. The GREEN AND YELLOW wire must be connected to the terminal in the plug which is marked with the letter “E” or by the Earth symbol or coloured GREEN or GREEN AND YELLOW.

2. The BLUE wire must be connected to the terminal which is marked with the

letter “N” or coloured BLACK.

3. The BROWN wire must be connected to the terminal which marked with the letter“L” or coloured RED.

Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the three wires.

                  

ViewSonic CD4233

Page 9

Ё೑⬉ᄤֵᙃѻક∵ᶧ᥻ࠊ󰵼䆚㽕∖(Ё೑RoHS⊩㾘󰵼⼎㽕∖)ѻકЁ᳝↦᳝ᆇ⠽䋼៪

ܗ㋴ⱘৡ⿄ঞ৿䞣 

䚼ӊৡ⿄

໪໇

䪙

(Pb)∲(Hg)䬝(Cd)

ƻƻƻ ƻ ƻ ƻ

᳝↦᳝ᆇ⠽䋼៪ܗ㋴

݁Ӌ䫀

(Cr 6+)

໮⒈㘨㣃

(PBB)

໮⒈Ѡ㣃䝮

(PBDE)

⎆᱊䴶ᵓ

⬉䏃ᵓ㒘ӊ

䰘ӊ

)䘹᥻఼ǃ⬉⑤㒓ǃ䖲᥹㒓*

䘹᥻఼⬉∴

ƻ˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼೼䆹䚼ӊ᠔᳝ഛ䋼ᴤ᭭Ёⱘ৿䞣ഛ೼SJ/T11363-2006󰵼ޚ㾘ᅮⱘ䰤䞣㽕∖

ҹϟ

h˖ 㸼⼎䆹᳝↦᳝ᆇ⠽䋼㟇ᇥ೼䆹䚼ӊⱘᶤϔഛ䋼ᴤ᭭Ёⱘ৿䞣䍙ߎSJ/T11363-2006 󰵼ޚ㾘ᅮⱘ䰤

䞣㽕∖

ƻƻ ƻ ƻ ƻ

ƻƻ ƻ ƻ

⦃ֱՓ⫼ᳳ䰤

ℸ󰵼䆚ᣛᳳ䰤(ᑈ)ˈ⬉ᄤֵᙃѻકЁ৿᳝ⱘ᳝↦᳝ᆇ⠽䋼៪ܗ㋴೼ℷᐌՓ⫼ⱘᴵӊϟϡӮথ⫳໪ ⊘៪さবˈ⬉ᄤֵᙃѻક⫼᠋Փ⫼䆹⬉ᄤֵᙃѻકϡӮᇍ⦃๗䗴៤Ϲ䞡∵ᶧ៪ᇍ݊Ҏ䑿ǃ䋶ѻ䗴៤ Ϲ䞡ᤳᆇⱘᳳ䰤Ǆ

ViewSonic CD4233

Page 10

NORTH EUROPE (NORDIC COUNTRIES) INFORMATION

Placering/Ventilation

VARNING:

FÖRSÄKRA DIG OM ATT HUVUDBRYTARE OCH UTTAG ÄR LÄTÅTKOMLIGA, NÄR DU STÄLLER DIN UTRUSTNING PÅPLATS.

Placering/Ventilation

ADVARSEL:

SØRG VED PLACERINGEN FOR, AT NETLEDNINGENS STIK OG STIKKONTAKT ER NEMT TILGÆNGELIGE.

Paikka/Ilmankierto

VAROITUS:

SIJOITA LAITE SITEN, ETTÄ VERKKOJOHTO VOIDAAN TARVITTAESSA HELPOSTI IRROTTAA PISTORASIASTA.

Plassering/Ventilasjon

ADVARSEL:

NÅR DETTE UTSTYRET PLASSERES, MÅ DU PASSE PÅ AT KONTAKTENE FOR STØMTILFØRSEL ER LETTE Å NÅ.

END-OF-LIFE DISPOSAL

Your new TV/Monitor contains materials that can be recycled and reused. Specialized companies can recycle your product to increase the amount of reusable materials and to minimize the amount to be disposed of.

Please find out about the local regulations on how to dispose of your old monitor from your local Viewsonic dealer.

(For customers in Canada and U.S.A.)

This product may contain lead and/or mercury. Dispose of in accordance to local-state and federal regulations. For additional information on recycling contact www.eia.org (Consumer Education Initiative)

WASTE ELECTRICAL AND ELECTRONIE EQUIPMENT-WEEE Attention users in European Union private households

This marking on the product or on its packaging illustrates that, under European Directive 2002/96/EG governing used electrical and electronic appliances, this product may not be disposed of with normal

household waste. You are responsible for disposal of this equipment through a designated waste electrical and electronic equipment collection. To determine the locations for dropping off such waste electrical and electronic, contact your local government office, the waste disposal organization that serves your household or the store at which you purchased the product.

Attention users in United States:

Like all LCD products, this set contains a lamp with Mercury. Please dispose of according to all Local, State and Federal Laws. For the disposal or recycling information, contact: www.mygreenelectronics.com or www.eiae.org.

ViewSonic CD4233

Page 11

Package Contents

The LCD monitor pack* should include:

• LCD monitor

• Power cord (1.8 m)

• VGA Signal Cable (1.8 m)

• CD User Manual & QSG

• Remote Control and AAA Batteries

• Main switch cover

• Screw for Main Switch cover x 6

• Clamper x 2

• Screw for Clamper x 2

Xxxxxxxxxxxx xx xxxxxxxxxxxx xxxxxxxxxxxx

xxxxxxxxx

CD Use

Manual & QSG

ew forMain switch cove

(M3 x 5) x 6

Main switch cove

* The supplied power co

d varies depending on destination.

For North America

Power cord

Please make sure that for

the

voltage of the power socket and has been approved by and complies with

the safety regulations of the particular country.

* You might like to save the package box and packing material for shipping the

monitor.

* The foll

• External

• Table

owing components are prepared as options.

Speakers

stand

all

other

regions, apply a

power cord thatconforms to

Screw for Clamper

(M4 x 8) x 2

Clamper x 2

Remote Con

Video Signal Cable

(D-SUB to D-SUB Cable)

ol and AAA

Batteries

ViewSonic CD4233

Page 12

Parts Name and Functions

Control Panel

POWER button ( ) : To switch the power on/off.

MUTE button : To switch the audio mute ON/OFF.

SOURCE button : To set the function while OSD menu is on or to activate input selection menu while OSD menu is off.

PLUS (+) button : To increase the adjustment while OSD menu is on, or to increase the audio output level while the OSD menu is

off.

MINUS (-) button : To decrease the adjustment while OSD menu is on, or to decrease the audio output level while the OSD menu is

off.

UP (S) button : To move the highlight bar up to adjust the selected item while OSD menu is on, or to activate the OSD menu when

the OSD menu is off.

DOWN (T) button :To move the highlight bar down to adjust the selected item while OSD menu is on, or to activate the OSD

menu when the OSD menu is off.

EXIT button : To return to previous menu while OSD menu is on or to activate the OSD menu when the OSD menu is off.

Main Power Switch : To turn the main power on/off.

Remote control sensor, Power indicator and ambient light sensor : To receive the IR signal from the remote control.

The indicator would show green when the LCD monitor is active and would turn red when the LCD is POWER OFF. While in the case of the system is in power save mode, it would show both green and red. When SCHEDULE is enabled, it would blink green and glow red. If the indicator blinks red , it tells that a failure is detected. on OSD menu.

The image brightness will be auto adjusted when “LIGHT SENSOR” set to “ON”

NOTE: Keyboard Control Lock Mode This function completely disables the access to all Keyboard Control functions. To enable

the keyboard control lock, press both of “S” and “T” buttons and hold down continuously for more than 3 seconds. To recover back to the user mode, press both of “S” and “T” and hold continuously for three 3 seconds.

ViewSonic CD4233

Page 13

Terminal Panel

EXTERNAL CONTROL (mini D-Sub 9 pin)

This is for serial connection when multiple monitors are connected. To achieve remote management through RS232C commands (refer to the RS232C remote control user manual), connect the RS232C OUT connector from a computer or from a different monitor to the RS232C IN connector from your monitor. The same RS232C commands can be looped through by connecting the RS232C OUT of this monitor to the next RS232C IN.

VIDEO IN/OUT

VIDEO IN connector (BNC and RCA): To input a composite video signal. Note that BNC and RCA are not available at the same time.

VIDEO OUT connector (BNC): To output the composite video signal from VIDEO IN connector.

S-VIDEO IN connector (MINI DIN 4 pin): To input the S-video (Y/C separate signal).

COMPONENT IN [Y, Pb, Pr] (BNC)

To connect an equipment such as a DVD player, HDTV device, or Laser disc player.

AC IN connector

To connect with the supplied power cord.

EXTERNAL SPEAKER TERMINAL

To output the audio signal to external speakers from AUDIO IN 1, 2, 3 jack or HDMI.

AUDIO OUT

To output the audio signal from the AUDIO IN 1,2 and 3 jack or HDMI.

AUDIO IN 1, 2, 3

To input audio signal from external equipment such as a computer, VCR or DVD player.

HDMI IN

To input digital video/audio signals from a digital equipment or computer.

DVI-D IN

To input digital video signals from a digital equipment or computer.

VGA IN (mini D-Sub 15 pin)

To input analog RGB signals from a computer or other RGB equipment.

VGA OUT (mini D-Sub 15 pin)

To output the signal from VGA IN.

ViewSonic CD4233

Page 14

Remote Control

MENU button

To turn the OSD menu on/off.

DOWN button

To move the highlight bar down to adjust the selected item when OSD menu is on.

o move the sub-picture down when in “PIP” mode.

INFO. button

To turn on/off the setting information displayed on the right-up corner of the screen.

SIZE button

To select the picture size from [FULL], [NORMAL], [CUSTOM] , [DYNAM IC] and [REAL].

VOLUME button

VOLˇ button: To increase the audio output level.

VOL

button˗To decrease the audio output level

VIDEO SOURCE button

To activate input selection menu, and push “S” or “T” to select input source from [HDMI], [DVI-D], [VGA],[COMPONENT], [S-VIDEO] and [VIDEO], and then push “ENTER” to switch to selected input source.

AUDIO SOURCE button

POWER button

To turn the power on/off. If LED Pow

remote control will not work.

er Indicator on the monitor is not lightening, then the

PICTURE MODE button

To select smart picture mode from [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA].

HIGHBRIGHT: for moving image such as Video

ANDARD: for images (Factory setting)

ST sRGB: for text based images CINEMA: for movies.

MONTION button

To expanded image slightly and moves 4 directions (up,down,right,left) periodically

PIP (Picture In Picture) button

ON/OFF button: To turn PIP mode ON/OFF. SOURCE button: To select the input signal for the sub-picture. SWEP button: To exchange between the main picture and sub-

picture.

Note:

The “PIP” and “POP” modes do not work if the screen size is “CUSTOM” , “DYNAMIC” or “REAL”.

To activate audio selection menu, and push “S” or “T” to select audio source from [AUDIO1], [AUDIO2], [AUDIO3] and [HDMI], and

then push “ENTER” to switch to selected audio source.

BRIGHTNESS button

o start the BRIGHTNESS OSD selection, and then push "

T button to adjust the value.

" or "ٙ"

UP button

To move the highlight bar up to adjust the selected item when OSD menu is on.

o move the sub-picture up when in “PIP” mode.

RIGHT button

To increase the adjustment with OSD menu.

o move the sub-picture right when in “PIP” mode.

EXIT button

To turn to the previous OSD menu.

AUTO SETUP button

To execute the AUTO ADJUST function.

MUTE button

To turn the mute function on/off.

ENTER button

To activate the setting with OSD menu.

LEFT button

To decrease the adjustment with OSD menu. To move the sub-picture left when in “PIP” mode.

ViewSonic CD4233

Page 15

Operating Range for the Remote

Control

Point the top of the remote control towards the LCD monitor's remote sensor during button operation. Use the remote control within a distance of about 7 m/ 23 ft from the front of the LCD monitor's remote control sensor and within a horizontal and vertical angle 30° with a distance of about 3 m/ 10 ft.

Handling the remote control

* Do not subject to strong shock. * Do not allow water or other liquid to splash the remote

control. If the remote control gets wet, wipe it dry

immediately. * Avoid exposure to heat and steam. * Other than to install the batteries, do not open the remote

control.

NOTE:

The remote control system may not function when direct sunlight or strong illumination strikes the remote control sensor of the LCD monitor, or when there is an obstacle in the radiation path.

ViewSonic CD4233

Page 16

Setup Procedure

1. Install the system on the right location

CAUTION:

THE LCD MONITOR MUST BE MOVED OR INSTALLED BY TWO OR MORE PERSONS. Failure to follow this caution may result in injury and damage

when the LCD monitor falls.

CAUTION:

DO NOT ATTEMPT TO INSTALL THE LCD MONITOR BY YOURSELF. The LCD display must be installed by a qualified technician. Contact your dealer for more information.

CAUTION:

DO NOT MOUNT OR OPERATE THE DISPLAY UPSIDE DOWN, FACE UP OR FACE DOWN.IT’S POSSIBILITY TO CLOCKWISE 90 DEGREES MOUNT. BUT DO NOT COUNTERCLOCKWISE 90 DEGREES MOUNT.

CAUTION:

DO NOT INSTALL THE LCD MONITOR WHERE IT WILL BE EXPOSED TO DIRECT SUNLIGHT.

Failure to follow this caution will result in display defects.

3. Connect to external equipment

• To protect the connected equipment, turn off the main power before making connections.

• Please refer to section “Connectivity” P.18~P.22 for operations.

4. Connect power cord

• The power outlet socket should be installed as near to the equipment as possible, and should be easily accessible.

• Fully insert the prongs into the power outlet socket. A loose connection may cause malfunctioning of the device.

NOTE:

Please refer to “Safety Operation” section of this manual for proper selection of AC power cord.

IMPORTANT:

Lay the protective sheet, which was wrapped around the LCD monitor when it was packaged, beneath the LCD monitor so as not to scratch the panel.

2. Install the remote control batteries

The remote control is powered by 1.5V AAA batteries. To install or replace batteries:

1. Press and slide to open the cover.

2. Align the batteries according to the (+) and (–) indications inside the case.

3. Replace the cover.

CAUTION:

Incorrect use of batteries can result in leaks or bursting. Be careful especially about the following points.

• Place “AAA” batteries matching the + and - signs on each battery to the + and - signs of the battery compartment.

• Do not mix battery types.

• Do not combine new batteries with used ones. It causes shorter battery life or leakage of batteries.

• Remove dead batteries immediately to prevent battery liquid from leaking into the battery compartment. Don't touch exposed battery acid, it cause damage to your skin.

NOTE:

If you do not intend to use the Remote Control for a long period, remove the batteries.

5. Turn on the power of the attached external equipment

When connected with a computer, turn on the power of the computer first.

6. Operate the attached external equipment

Display the signal from the external equipment by selecting the correct video and audio sources first.

7. Adjust the sound

Make adjustments to lower or to rise the volume as required.

8. Adjust the screen

Make adjustments to the display position or settings if required.

ViewSonic CD4233

Page 17

9. Adjust the image

Make adjustments to brightness or contrast if required.

10. Recommended Adjustment

To reduce the risk of “image persistence”, please adjust the following items based on the application being used. “POWER SAVE”, “PANEL SAVING”, “DATE AND TIME”.

11. To prevent the main power switch from being changed

To prevent the possibility of main power switch being carelessly pushed, please attach the main switch cover (accessory) onto it.

NOTE:

With the main turn off the display.

power switch cover in place, the main power switch can not be turned off. Remove main power switch cover in order to

ViewSonic CD4233

Page 18

How to Mount and Attach Feet to the LCD Monitor

You can install the LCD monitor in one of the following two ways:

Method 1: Attach and remove the optional stands

How to install stands

1. Please turn the monitor off.

2. After inserting stand in guide block, fasten the thumbscrews on both sides of the monitor.

NOTE:

Install the table stand with the longer end of the feet directing to the front.

In the upright

How to remove the stands

1. Spread the protective sheet on the flat surface.

2. Make the monitor lying on the protective sheet.

3. Remove screws using a screwdriver and place them in a safe place for reuse.

position

ViewSonic CD4233

Page 19

To avoid monitor from falling

Take measures to prevent the monitor from falling over in case of an earthquake or other disaster might occur to lessen the probability of injury and damage. As shown in the figure below, secure the monitor to a solid wall or pillar using rope (commercially available) strong enough to bear the weight of the monitor( approx. 47.5 kg). Screw hooks (commercially available), of ring type rather than C-shaped screw hooks (with opening), are recommended.

aution:

y Though the recommended prevention from falling is intended to lessen the probability of injury and damage, it doesn’t assure its

effectiveness against any kind of earthquake or disaster.

y Before moving the monitor, remove the rope that is securing the monitor.

Screw here is not supplied.

Method II: Mount the monitor on the wall

Before mounting the monitor to the wall, make sure that the system has been power-off and you have obtain a standard wall-mounting kit (commercially available). Using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America is recommended.

1. Lay a protective sheet on a table, which was wrapped around the monitor when it was packaged, beneath the surface as not to scratch the screen face.

2. This device cannot be installed without the correct and complete mounting accessories (not provided in the box). Make sure you have all related parts available for wall mounting.

3. Follow the instructions that come with the base mounting kit. Failure to follow correct mounting procedures could result in damage to the equipment or injury to the user or installer. Product warranty does not cover damage caused by improper installation.

4. For the wall-mounting kit, use M6 mounting screws for 400x 400 mm pattern (having a length 10 mm longer than the thickness of the mounting bracket) and tighten them securely. (Recommended torque: 470 - 635N•cm).

Caution:

For preventing the monitor from falling. y Install the monitor with metal brackets for wall or ceiling installation (commercially available) on your own responsibility. For detailed

procedures of installation, refer to the instructions of the metal brackets.

y To lessen the probability of injury and damage resulting from fall of the monitor in case of earthquake or other disaster, be sure to

consult the bracket manufacturer for installation location.

y To lessen the risk of falling of the monitor, thread commercially available rope (having a load capacity at least 1960N (200kgf)) through

the handles at the right and left of the monitor and secure the rope to the wall mount brackets or ceiling mount brackets.(Refer to the first paragraph of this page.)

ViewSonic CD4233

Page 20

Ventilation Requirements for enclosure locating

To allow heat to disperse, leave space between surrounding objects as shown in the diagram below.

ViewSonic CD4233

Page 21

Connectivity

Before making connections:

* First turn off the power of all the attached equipments before make connections. * Refer to the user manual included in each separate piece of equipment.

Connectivity Diagram

ViewSonic CD4233

Page 22

Connecting to a Personal Computer

As you finish the connection between the computer and the LCD monitor, you could play the contents in the computer and display them on the LCD monitor.

Connecting the LCD Monitor to a Personal Computer

• To achieve this, apply the supplied VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin) to make connection between a PC and the LCD monitor (VGA IN connector).

• When connecting more than one LCD monitors to a PC, apply another VGA signal cable (mini D-sub 15 pin to mini D-sub 15 pin; it’s commercially available) to make connection between the LCD monitor(VGA OUT connector) and the other (VGA IN connector).

• The AUDIO IN 1, 2, 3 or HDMI can be connected for audio input. After choosing one of the AUDIO IN connectors, you might need to select AUDIO 1, 2, 3 or HDMI using the AUDIO SOURCE button on the remote control.

• When connecting more than one LCD monitors to a PC, apply RCA cable to make connection between the LCD monitor(AUDIO OUT connector) and the other (AUDIO IN 1, 2, 3). HDMI source is not suitable for this case.

ViewSonic CD4233

Page 23

Connecting to a Digital Interface Equipment

Connections can be made between the LCD monitor and other digital equipment that is equipped with a digital interface compliant with the DVI (Digital Visual Interface) standard.

Connect the LCD Monitor to a Computer with a Digital Output

• The HDMI , DVI-D IN connector accepts a HDMI cable.

• HDMI and DVI-D can receive HDMI video signals from either a HDMI output of for instance a DVD player or from a DVI-D output of a PC.

• To ensure the display quality, use a cable with a quality prescribed by DVI standards.

• The AUDIO IN 1, 2, 3 or HDMI connector can be chosen to receive an audio source. Select AUDIO 1, 2, 3 or HDMI from the AUDIO SOURCE button on the remote control. HDMI(for audio) is only selectable only when HDMI or DVI-D (for video) is selected.

• Note that the signal of a HDMI / DVI-D connector cannot be output to the VGA OUT connector.

ViewSonic CD4233

Page 24

Connecting to a DVD Player

As you finish the connection between the DVD player and the LCD monitor, you could display the contents from the played DVD on the LCD monitor. You might like to refer to your DVD player’s manual for further information.

Connect the LCD Monitor to a DVD Player

• To achieve this, apply a 3x components cable (Y, Pb, Pr) with BNC connectors at one end and RCA connectors at the other end between DVD player and display. In case you can only obtain RCA connectors on both ends you can use the in box available BNCto-RCA converters.

DVD player(Y, Pb, Pr Out) and LCD monitor (COMPONENT). You might need BNC-to-RCA adapters(including in the accessories) to

convert the BNC connectors to RCA connectors if you are using the separated signaling(Y, Pb, Pr) RCA cable.

• If your DVD player supports HDMI signaling, apply a HDMI to HDMI cable for the connection.

• The AUDIO IN 2 , 3 (both of RCA connector type) can be used for audio input. Select [AUDIO 1] (for 3.5ĳ phone jack), [AUDIO 2], [AUDIO 3] Or [HDMI] from the AUDIO SOURCE button on the remote control. HDMI (for audio) is selectable only when HDMI or DVID (for video) is selected.

ViewSonic CD4233

Page 25

Connecting to a Stereo Amplifier

You can connect your stereo amplifier to your LCD monitor. Refer to your amplifier's manual for further information.

Connect the LCD Monitor to a Stereo Amplifier

• Turn on the LCD monitor and the amplifier only after all connections have been finished.

• Apply 2 RCA cables (audio left and right) to make connection between the amplifier (audio in) and the LCD monitor (audio out).

• Do not reverse the audio left and right jacks.

• For the preferred audio signal, select [AUIDO1], [AUDIO2], [AUDIO3] or [HDMI] from the AUDIO SOURCE button on the remote control. HDMI(for audio) is selectable only when HDMI or DVI-D (for video) is selected.

• The AUDIO OUT RCA connectors output sound from the selected AUDIO SOURCE.

Connecting to a display mounted PC

This monitor has an area in the backcover to mount a small form fact PC or set-top box. You can connect your mounted PC to your LCD monitor. Use M4 mounting screws for 100x200 mm to fix your mount PC.

ViewSonic CD4233

Page 26

Basic Operation

Power ON and OFF Modes

The LCD monitor power indicator will turn green while powered on and will turn red while powered off. The monitor can be powered on or off using the following three options:

1. Pressing the Main Power Switch.

NOTE:

When the Main Power Switch is used to power off the LCD monitor, the remote control, the power button and the indicator will not work. Make sure to turn the Main Power Switch on before using the other two options.

2. Pressing the power button.

NOTE:

Before pressing the power button, be sure to turn on the Main Power button on the LCD monitor.

3. Using the remote control.

NOTE:

Before operating the remote control, be sure to turn on the Main Power Switch on the LCD monitor.

ViewSonic CD4233

Page 27

Power Indicator

Status Power ON Green Power Standby Red Power OFF LED Off Diagnosis (Detecting failure)

Red Blinking

* See troubleshooting

Using Power Management

Please turn off the LCD monitor when it will not be used for long time. This could potentially increase the life and decrease the power consumption of the LCD monitor.

Standby mode: Push the power button on the remote control or on the monitor to enter the standby mode. Power Off: Push the Main Power Switch to enter the power off mode.

Display Signal of Video Source Setting to [VIDEO]

Use the input button on the front panel or the VIDEO SOURCE button on the remote control to set video source to [VIDEO]. Use the COLOR SYSTEM OSD menu to select [AUTO], [NTSC], [PAL], [SECAM], [PAL60], [4.43NTSC], according to your video format.

Picture Size

HDMI, DVI-D, VGA FULL NORMAL CUSTOM

REAL

COMPONENT, VIDEO FULL NORMAL DYNAMIC

REAL CUSTOM

Sign

al Type NORMAL SIZE Recommended Size

NORMAL

4:3

Squeeze

NORMAL: Display with the input signal aspect ratio from PC signal, or display in 4:3 aspect ratio at COMPONENT or VIDEO signal. FULL: Display in the entire screen.

DYNAMIC: Expand 4:3 pictures to the entire screen with non-linearity. (Some round image might be cut by expansion.) CUSTOM (ZOOM): Images can be expanded beyond the active display area. The image which is outside of the active display area would

not be shown. REAL: Image will be displayed for one by one pixel.

ZOOM

DYNAMIC

FULL

ZOOM

ViewSonic CD4233

Page 28

Smart Picture Mode

HDMI, VGA HIGHBRIGTH STANDARD sRGB

COMPONENT, VIDEO HIGHBRIGTH STANDARD CINEMA

Audio Source Switching

You can select the audio source using the AUDIO SOURCE button on the remote control.

HDMI

HDMI AUDIO1 AUDIO2 AUDIO3

Control Lock Mode

This function disables the operation o buttons so that the adjustments you make are not active when they are pressed. To disable the buttons, press and hold down the S and T buttons together for at least 3 seconds.

To enable the buttons, press and hold down the S and T buttons together for at least 3 seconds again.

OSD Information

HDMI, VGA

VGA 1024 x 768

48kHz 60Hz

AUDIO : 1 SIZE : FULL

COMPONENT

COMPONENT 1080P AUDIO : SIZE : FULL

Video Source Input signal Information

Audio Source Picture Size

Video Source Input signal Information Audio Source Picture Size

S-VIDEO, VIDEO

S-VIDEO NTSC AUDIO :3 SIZE : NORMAL

Video Source

Color System of Input Signal

Audio Source Picture Size

PIP or POP

Main:VGA Sub:S-VIDEO

VGA 1024 x 768 48kHz 60Hz AUDIO : 1 S-VIDEO NTSC SIZE : FULL

Main picture Information

Sub picture Information

picture

Main

Information

ViewSonic CD4233

Page 29

OSD (On-Screen-Display) Controls

ess MENU button to open Main menu. Press UP or DOWN button to select sub-

Remote Control

Control Panel

UP or DOWN button SOURCE button “+” “-” button EXIT button

menu.

Press EXIT button to open Main menu. Press UP or DOWN button to select.

ess ENTER button Press MENU or

to enable setting. EXIT button to exit.

Press SOURCE button to enable the setting.

Press UP or DOWN, and LEFT or RIGHT button to select function, or adjust the setting. Press ENTER button to enable the setting.

Press EXIT button to exit.

OSD screen

ViewSonic CD4233

Page 30

Main-Menu

PICTURE

BRIGHTNESS

Adjusts the overall image and background screen brightness. Press ُ button to increase brightness. Press ٙ button to decrease brightness.

CONTRAST

Adjusts the image brightness for the input signal. Press ُ button to increase contrast. Press ٙ button to decrease contrast.

SHARPNESS

This function is digitally capable to keep crisp images at any timing. It is adjustable to get a distinct image or a soft one as you prefer and set independently for each picture mode. Press ُ button to increase sharpness.

Press ٙ button to decrease sharpness.

BLACK LEVEL

Adjusts the image brightness for the background. Press ُ button to increase black level. Press ٙ button to decrease black level. NOTE: sRGB picture mode is standard and cannot be changed.

NOISE REDUCTION

Adjusts the noise reduction level. Press ُ button to increase reduction level. Press ٙ button to decrease reduction level.

COLOR TEMPERAT URE

Is used to adjust the color temperature. The image becomes reddish as the color temperature decreases, and becomes bluish as the color temperature increases.

ViewSonic CD4233

Page 31

LIGHT SENSOR

Select “ON” to enable the ambient light sensor. The image brightness will be auto adjusted when ambient light changed.

DYN

AMIC CONTRAST

Select “ON” to enable the dynamic conctrast mode. Can enhancement the image of high contrast ratio.

PICTURE RESET

Selecting Picture reset allows you to reset all OSD settings about PICTURE setting. Select “Yes” and press “ENTER” button to restore to factory preset data. Press “EXIT” button to cancel and then return to the previous menu.

ViewSonic CD4233

Page 32

Main-Menu

SCREEN

H POSITION

Controls Horizontal Image position within the display area of the LCD. Press ُ button to move screen to right. Press ٙ button to move screen to left.

V POSITION

Controls Vertical Image position within the display area of the LCD. Press ُ button to move screen to UP. Press ٙ button to move screen to DOWN.

CLOCK * : INPUT VGA only

Press ُ button to expand the width of the image on the screen the right. Press ٙ button to narrow the width of the image on the screen the left.

CLOCK PHASE

Improves focus, clarity and image stability by increasing or decreasing this setting.

* : INPUT VGA only

ZOOM MODE

You can select “FULL”, “NORMAL” and “CUSTOM” and “REAL”. (INPUT HDMI,DVI-D,VGA only) You can also select “FULL”,“NORMAL” “DYNAMIC” and “CUSTOM” and “REAL”. (INPUT COMPONENT, S-VIDEO, VIDEO only) Selecting “DYNAMIC” will make the screen display panoramic with the expansion of the middle and outside of the screen changed. (The upper and the bottom of the image will be cut by expansion.)

Dynamic image is the same as FULL size image when HDTV signal is input.

Selecting “REAL” image will be displayed 1 by 1 pixel.

ViewSonic CD4233

Page 33

SCREEN RESET

Selecting Screen reset allows you to reset all OSD settings from PICTURE setting. Select “Yes” and press “ENTER” button to restore the factory preset data. Press “EXIT” button to cancel and then return to the previous menu.

ViewSonic CD4233

Page 34

Main-Menu

AUDIO

BALANCE

Adjusts the balance of L/R volume. Press ُ button to move the stereo sound image to right. Sound of the left side will be small. Press ٙ button to move the stereo sound image to left.

TREBLE

This feature helps you to accentuate or reduce the high frequency sound. Press ُ button to increase TREBLE sound. Press ٙ button to decrease TREBLE sound.

BASS

This feature helps you to accentuate or reduce the low frequency sound. Press ُ button to increase BASS sound. Press ٙ button to decrease BASS sound.

SPEAKER

This feature helps you to cut the internal or the external loudspeaker. Press ُ or ٙ button to exchanges the internal and the external loudspeaker.

AUDIO RESET

Selecting Audio reset allows you to reset all OSD settings from AUDIO setting. Select “YES” and press “ENTER” button to restore the factory preset. Press “EXIT” button to cancel and then return to the previous menu.

ViewSonic CD4233

Page 35

Main-Menu

PIP (PICTURE IN PICTURE)

Note: The “PIP” and “POP” modes do not function when the screen size is “CUSTOM” or “REAL”.

PIP SIZE

Selecting the size of picture inserted at the “Picture-in-Picture” (PIP) mode. “Large”, “Middle” and “Small” are available.

PIP AUDIO

Selecting the sound source in PIP mode. When selecting “MAIN AUDIO”, you will get the sound for the main picture and when selecting “PIP AUDIO”, you will get the sound for the picture instead.

PIP RESET

Selecting PIP Reset allows you to reset all OSD settings from PIP setting. Select “Yes” and press “ENTER” button to restore the factory preset data. Press “EXIT” button to cancel and then return to the previous menu.

ViewSonic CD4233

Page 36

Main-Menu

CONFIGURATION 1

AUTO ADJUST * : INPUT VGA only

Press "ENTER" button to automatically adjust screen size, horizontal position, vertical position, clock, clock phase, white level and black level. Press " EXIT " button to cancel execution AUTO ADJUST and then will return to the previous menu.

POWER SAVE

Selecting RGB "ON", the monitor will go to power management mode when HDMI, DVI-D,VGA, sync is lost. Selecting VIDEO "ON", the monitor will go to power management mode after about 10 minutes delay from when COMPONENT and VIDEO input signal is lost.

LANGUAGE

OSD control menus are available in eight languages. (English, German, French, Italian, Spanish, Polish, Turkish, Russian, Simple Chinese)

SCREEN SAVER

Select "SCREEN SAVER" functions to reduce the risk of the "image persistence". COOLING FAN: The cooling fan will be auto-turned on and off according to temperature of monitor when selected “AUTO”. The cooling fan will be turned on always when selected “ON”. BRIGHTNESS: The brightness is decreased when selected " PIXEL MOTION: Image is slightly expanded and moves 4 directions (UP, DOWN, RIGHT, LEFT) periodically (Need setting the time for movement). Movement area is approximately +/- 5pixel from original position; Please locate the important information such as text within 90% area of screen image. See note (1) for this functions. PIP will be disabled when "MOTION" is active.

High, Middel and Low ".

CONFIGURATION RESET

Selecting the CONFIGURATION RESET allows you to reset all configuration settings. Select "Yes" and press "ENTER" button to restore the factory preset data. Press " EXIT " button to cancel and return the previous menu.

FACTORY RESET

Selecting "YES" allows you to reset PICTURE, SCREEN, AUDIO, CONFIGURATION1,2 and ADVANCED OPTION will be back to factory settings (except LANGUAGE, DATE AND TIME and SCHEDULE). Select "YES" and press "ENTER" button to restore the factory preset data. Press " EXIT " button to cancel and return the previous menu.

ViewSonic CD4233

Page 37

Main-Menu

CONFIGURATION 2

OSD TURN OFF

The OSD control menu will stay on as long as it is used. In the OSD Turn Off submenu, you can select how long the monitor waits after the last touch of a button to shut off the OSD control menu. The preset choices are 5 -120 seconds.

INFORMATION OSD

Selects the information OSD to be displayed or not. The information OSD will be displayed when the input signal is changed or a source change or warning message like no-signal or out-of range. A time between 1 to 10 seconds is available.

SLEEP TIMER

To select SLEEP TIMER mode ON/OFF. In the SLEEP TIMER menu, you can preset the monitor to automatically power down. A time between 1 to 24 hours is available. When the SLEEP TIMER is set, the SCHEDULE settings will be disabled.

OSD H POSITION

Adjusts the horizontal position of the OSD menu.

OSD V POSITION

Adjusts the vertical position of the OSD menu.

MONITOR INFORMATION

Indicates the model and serial number of your monitor.

ViewSonic CD4233

Page 38

Main-Menu

ADVANCED OPTION

INPUT RESOLUTION * : INPUT VGA only

This feature makes the display controlling the source in order to match display capabilities by choice or automatically. You can select one of the following timings: (1)1024x768, 1280x768, 1360x768 and 1366x768. (2) 640x480, 720x480 and 852x480 (3) 800x600, 1064x600 and 720x576 (4) 1400x1050 and 1864x1050 (5) 720x400 and 640x400 AUTO: Determines the resolution automatically. The setting you select becomes effective when POWER is turned OFF and ON again.

GAMMA SELECTION

Selects a display gamma. It refers to the brightness performance curve of signal input.

2.2

2.4 S gamma Native NOTE: sRGB picture mode is standard and cannot be changed.

IR CONTROL

Selects the operation mode of the remote controller when multiple monitors are connected via RS232C. The item in this menu will become effective by pressing “ENTER” button on the selected item. NORMAL: The monitor will be controlled normally by remote controller. PRIMARY: The first monitor of those multi-connected via RS232C is designated as PRIMARY. SECONDARY: monitors other than the first one multi-connected via RS232C are designated as SECONDARY. LOCK: Disable the monitor control by infrared remote controller. Keep pressing “DISPLAY” button during 5 sec or more, this setting will return to “NORMAL”.

KEYBOARD CONTROL

Selects the operation mode of the keyboard control. Select “LOCK” to disable the keyboard. Select “UNLOCK” to enable the keyboard.

TILING

TILING demonstrates multiple screens. This feature provides a single large screen using up to 25 monitors. It will be able to divide up to 5 each H and V. This requires you to feed the PC output into each of the monitors through a distributor. H MONITORS: Select number of horizontal monitors. V MONITORS: Select number of vertical monitors. POSITION: Select a position to expand the screen. FRAME COMP: Works in tandem with TILING to compensate for the width of the tile bezels in order to accurately display the image. ENABLE: Select “YES”, the monitor will expand the selected position. PIP and STILL will be disabled when “TILING” is activated.

ViewSonic CD4233

Page 39

HEAT STATUS * : Disclamer: Heat sensor is indicative.

HEAT STATUS allows you to watch the thermal status at any time via the OSD menu and/or via RS232C commands. The indicated temperature has a accuracy of 3 degrees (plus and minus).

Press “ENTER” button to enter the submenu to monitor the heat status. Press “EXIT” button to cancel and then return the previous menu.

DATE AND TIME

Adjusts the current date and time for internal clock. You should set this function when you use “SCHEDULE”.

SCHEDULE

Programs the monitor's working schedule. Schedules the power on and power off by using hour and a day of the week. Also sets the input port. This OSD can't be removed except EXIT.

MONITOR ID

ID numbers for remote control are assigned to monitors that are multi-connected via RS232C. ID numbers 1 to 26 are selectable.

DDC/CI

Use to turn ON or OFF the DDC/CI communication function. Select ON for normal use.

ADVANCED OPTION RESET

Selecting ADVANCED OPTION RESET allows you to reset all OSD settings from ADVANCED OPTION settings, except for GAMMA SELECTION, DATE AND TIME, SCHEDULE, HDMI INPUT MODE, DVI-D INPUT MODE,MONITOR ID, and DDC/CI. Select “YES” and press “ENTER” button to restore the factory preset data. Press “EXIT” button to cancel and then return the previous menu. GAMMA SELECTION is reset when carrying out the PICTURE RESET in the PICTURE.

ViewSonic CD4233

Page 40

NOTE

NOTE 1: IMAGE PERSISTENCE

Please be aware that LCD Technology may experience a phenomena known as Image Persistence. Image Persistence occurs when residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image. As with all personal display devices, ViewSnoic recommends displaying moving images and using a moving panel saving at regular intervals whenever the screen is idle or turning off the monitor when not in use.

Please set “POWER SAVE”, “SCREEN SAVER”, “DATE AND TIME” and “SCHEDULE” functions to further reduce the risk of Image persistence.

For long life use of Public Display

< Image Sticking of LCD Panel >

When LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or “ghost” image of previous image may be observed. (Image Persistence) Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along the displayed image, and it is observed permanently. (Image Sticking)

< Recommendations >

For preventing the fast transition to Image Sticking, and for longer life usage of LCD, following are recommended.

1. Static images should not be displayed for long period. Always use a short cycle to change to other images.

2. In case a fixed image is displayed for a long period, it is four directions

3. When not in use, please turn off the monitor with your remote control, or use Power Management Function or use the Schedule Function of monitor.

4. Reducing the environmental temperature will increase the life of your monitor.

When Protection board (glass, acryl) is installed over the LCD surface, enclosed into the box / wall, or stack the monitor, please utilize

the temperature sensors inside monitor.

To reduce the environmental temperature, the monitor should be set Low Brightness or Cooling Fan “ON” by using Screen sever Function.

5. Please use "SCREEN SAVER Mode" of monitor.

advised to activate the MOTION feature that will periodically move the image in

NOTE 2: HOW TO SETUP SCHEDULE

Using the “SCHEDULE” function allows you to set up to seven different scheduled time intervals when the LCD Monitor will be activated. You can select the time the monitor turns on and turns off, the day of week the monitor is activated, and which input source the monitor will use for each scheduled activation period. A check mark in the box next to the number of the schedule indicates that the selected schedule is in effect. To select which schedule to set, use the up/down arrows to move the number (1 to 7) of the schedule.

Use the (ُ) and (ٙ) buttons to move the cursor horizontally within the particular schedule. Use the ( ) and ( ) buttons to increase time

and select input port. The “ENTER” button is used to make a selection. If you create a schedule but do not want to use a power on time, select “--” in the “ON” time slot. If you do not want to use a power off time select “--” in the OFF time slot. If there is no input selected (“--” showing in the input spot) the input from the previous schedule will be used. The selection of EVERY DAY within a schedule takes priority over other schedules that are set up to operate weekly. When schedules are overlapping, scheduled Power ON time has priority over scheduled Power OFF time. If there are two schedules programmed for the same time, then the highest numbered schedule has priority. When the “SLEEP TIMER” is set, the “SCHEDULE” function is disabled.

ViewSonic CD4233

Page 41

NOTE 3: “PIP”, “POP” and “SIDE BY SIDE”

The following table shows the combination of signal inputs under which the “PIP” and “POP” modes function. These modes do not function, however, when the screen size is “CUSTOM” or “REAL”.

SUB

HDMI DVI-D VGA COMPONENT S-VIDEO VIDEO

HDMI

DVI-D

VGA

COMPONENT

MAIN

S-VIDEO

VIDEO

{

±± ±

{{ {

{{

±±

 {: Supported

±: Not supported

Press the “PIP ON/OFF” buttons on the remote control to change between “PIP”, “POP” and “SIDE BY SIDE” mode as shown in the diagram below.

PIP POP

SIDE BY SIDE

ASPECT

SIDE BY SIDE FULL

OFF

“PIP”, “POP” mode resolution (Reference)

PIP SIZE

POP SIZE

SMALL

MIDDLE LARGE

: 450 dots X 338 dots : 675 dots X 450 dots : 900 dots X 675 dots : 450 dots X 338 dots

< Remote control numbering function >

By connecting multiple monitors using RS232C cables, you can control any one monitor or all the monitors by one remote controller.

1. Assign arbitrary ID number to each of multi-connected monitors using MONITOR ID. ID numbers 1 to 26

are selectable. It is recommended to assign sequential ID numbers from 1 and up.

2. The remote control mode of the first monitor is set to PRIMARY and those of the other monitors are set to

SECONDARY.

3. When you direct the remote controller at the remote control signal sensor of the PRIMARY monitor and press the DISPLAY

button on the remote controller, the ID selection OSD appears at the upper left of the screen.

ID number of the currently viewed monitor

Select the ID number of the monitor you want to control using the ُ/ٙ button on the remote controller. The ID of the monitor you want to control is displayed at the upper left of its screen. By selecting ALL, you can control all the multi-connected monitors.

4. Direct the remote controller at the remote control signal sensor of the PRIMARY monitor. OSD

appears on the monitor having the ID number you selected.

NOTE:

When the ID selection OSD is being displayed on the PRIMARY monitor, press the DISPLAY button on the remote controller again to cancel the ID selection OSD and then control the monitor you selected.

HINT:

If you set the remote control mode wrongly and remote control operation becomes unavailable, press MENU button on the control panel of the monitor to display the OSD screen and change the remote control mode using ADVANCED OPTION. By pressing

and holding down the DISPLAY button on the remote control for 5 seconds or longer, the remote control mode is initialized to

NORMAL.

ViewSonic CD4233

Page 42

Features

Full HD LCD display 1920x1080p

This display has a resolution that is referred to as Full HD. The state-of-the-art LCD screen technology has the full high-definition widescreen resolution of 1080 progressive lines, each with 1920 pixels. This allows the best possible picture quality for HD input signals with up to 1080 lines. It produces brilliant flicker-free progressive scan pictures with optimum brightness and superb colors. This vibrant and sharp image will provide you with an enhanced viewing experience.

Slim bezel

A slim bezel design adds a stylish look to a public display to nicely blend in most environments. Furthermore this design is ideal for tiled matrix video walls.

Zoom function for tiled matrix

The internal zoom function enables easy implementation of a video wall matrix, without the need for expensive external equipment. Capable of a vidiwall of 25 displays by dividing up to 5 displays each horizontally and vertically.

High brightness

Allows daylight viewing even in large public environments with high ambient light conditions due to its 700 cd/m² high brightness professional panel.

Network controllability: RS232C

Network controllability allows user to control and adjust monitors remotely through RS232C protocol.

Smart insert

Professional PC's are part of most public signage installations. Quite often they add additional depth to the public display and a lot of cable clutter. This public display contains a Smart insert in the backcover that will fit many professional small form factor PC's. In addition it offers provisions for efficient cable management.

SmartPower

The backlight intensity can be controlled and pre-set by the system to reduce the power consumption by up to 50%, which saves substantially on energy costs.

Advanced anti image sticking

Static images left on-screen for extended periods of time may leave a "ghost image" or image sticking effect on LCD displays. Although image sticking in LCD displays is not permanent, you want to prevent this to happen, especially in locations where content is shown 24/7.

Compliant with RoHS standards

Viewsonic designs and produces display products in compliance with strict Restriction of Hazardous Substances (RoHS) standards that restrict lead and other toxic substances that can harm the environment.

Automatic Long Cable Compensation:

Automatic long cable compensation prevents image quality degradation (color shift and dull signals) caused by long cable lengths.

ViewSonic CD4233

Page 43

Troubleshooting

No picture

• The signal cable should be completely connected to the graphics card/computer.

• Front Power Switch and computer power switch should be in the ON position.

• Check to make sure that a supported mode has been selected on the graphics card or system being used.

(Please consult graphics card or system manual to change graphics mode.)

• Check the monitor and your graphics card with respect to compatibility and recommended settings.

• Check the signal cable connector for bent or pushed-in pins.

• If nothing is displayed on the screen when HDCP device is connected, reset the power of the device.

Power Button does not respond

• Unplug the power cord of the monitor from the AC outlet to turn off and reset the monitor.

Image persistence

• Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when

a residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not permanent, but constant images being displayed for a long period of time should be avoided. To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.

NOTE:

As with all personal display devices, VIEWSONIC recommends displaying moving images and using a moving panel saving at regular intervals whenever the screen is idle or turning off the monitor when not in use.

Image is unstable, unfocused or swimming is apparent

• Signal cable should be completely attached to the computer.

• Use the OSD Image Adjust controls to focus and adjust display by increasing or decreasing the fine adjustment. When the display

mode is changed, the OSD Image Adjust settings may need to be re-adjusted.

• Check the monitor and your graphics with respect to compatibility and recommended signal timings.

• If your text is garbled, change the video mode to non-interlace and use 60 Hz refresh rate.

Image of component signal is greenish

• Check to see if the COMPONENT input connector is selected.

LED on monitor is not lit (no green or red color can be seen)

• Power Switch should be in the ON position and power cord should be connected.

• Make certain the computer is not in a power-saving mode (touch the keyboard or mouse).

RED LED on monitor is blinking

• A certain failure might have occurred, please contact your nearest authorized VIEWSONIC service facility.

Display image is not sized properly

• Use the OSD Image Adjust controls to increase or decrease the coarse adjustment.

• Check to make sure that a supported mode has been selected on the graphics card or system being used.

(Please consult graphics card or system manual to change graphics mode.)

Selected resolution is not displayed properly

• Use OSD Display Mode to enter Information menu and confirm that the appropriate resolution has been selected.

If not, select corresponding option.

ViewSonic CD4233

Page 44

No Sound

• Check to see if speaker cable is properly connected.

• Check to see if mute is activated.

• Check to see if volume is set at minimum.

Remote Control does not work

• Check the Remote Control’s batteries status.

• Check if batteries are inserted correctly.

• Check if the Remote Control is pointing at the monitor’s remote sensor.

“SCHEDULE” / “SLEEP TIMER” function is not working properly

• The “SCHEDULE” function will be disabled when the “SLEEP TIMER” is set.

• If the “SLEEP TIMER” function is enabled and the power to the LCD monitor is turned off if the power supply is interrupted

unexpectedly, then the “SLEEP TIMER” will be reset.

Stripe Noise

Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or degradation.

“NO SIGNAL” is displayed on the screen

Image may not be displayed right after HDCP device is connected.

ViewSonic CD4233

Page 45

Specifications

Product Specifications Analog Input Digital Input

LCD

Module

Brightness:

equency Horizontal:

Pixel

Clock

iewable

Size

Input

Signal

PC-Input:

VIDEO

Input:

AUDIO

Input:

RS232C:

Output

Signal

PC-Output:

VIDEO

Output:

AUDIO

Output:

Speaker

Output:

RS232C: Out:

Resolutions

Supported

Diagonal:

Pixel Pitch:

Resolution:

Color:

Contrast

Response

Input-terminal:

Output-terminal:

iew

Ratio:

time:

Angle:

ertical:

ideo:

Sync:

ideo:

Sync:

42"/106.7

0.485 1920x1080

1.07 700 1,000:1 9 ms (typ.Gto Up

15.625

50.0/58.0-75.0

13.5

930.25 x 523.25mm/

Analog RGB Input SeparateHVsync: 15 Composite: Input Y/CY:1 Impedance 75 Component: Input RCA

In:

Analog RGBVideo: 0.7

SeparateHVsync: 15 BNC-OUTPUTx1, RCA Internal Speaker 5W+5W(8 External Speaker 9

640x480at60

1024x768at60Hz 1280 x 720 at 60Hz

1280x768at60Hz

1600x1200at60

1920x1080at60Hz* *

Recommended Resolution

NTSC,P

dots

billion

colors

cd/m2 (typ.)

(typ.) , 3,000:1Dynamic Contrast

and Down 178°,

15.734, 31-91

-165.0

impedance 75

Mini D-sub

impedance 75ohm BNC and

Impedance 75 PIN-JACK L/R Mini D-sub

Mini D-sub

PIN-JACK L/R

Mini D-sub

AL,SECAM,4.43NTSC,PAL60

(depending on video cardused)

Left

and Right 178°

kHz

MHz

36.6x20.6 inches

ideo: 0.7

1.0

Vp-p

1.0/0.7

Vp-p

ohm

TTL

level (Pos./Neg.),

Vp-p

C: 0.286

ohm

Jack7W+7W(8

Vp-p Input

S-TERMINAL-INPUT

Vp-p

ohm

BNC-INPUT

INPUTx2,

Vp-p

TTL

with75ohm

level (Pos./Neg.)

Composite OUTPUTx1, 0.15Vrms

1900x1200 (reduced Blanking only)

RCA-PINJACK-INPUT

STEREO

1.0

Vp-p

ohm)

800x600at60Hz

1360x768at60Hz

DVD:480i,480p,

(typ.)

Input

Impedance 2.2K

Mini Jack

terminated

with75ohm

with

@CR>10

ohm

INPUTx1

terminated

47k

ohm

terminated

576i,720p,1080i,1080p

25.0

TMDS

HDMI

-165.0

MHz

Power Supply 2.4– 1.1 A@100-240VAC,50~60Hz Power

Consumption

Operational Envir

onment

Storage Envir

onment

Dimension Net

eight Net

Wall

mounting

Complied

Power Management

Plug&Play

Accessories

interface

Regulatory

and

Note:Technical

Power

Save:

emperatur

Humidity:

emperatur

Humidity:

without

with

without

with

oss:

stand:

Gr stand:

stand:

Net

Net Gr

Guidelines

specifications

Typically Less than 1W (Power button off or main power switch off.)

Landscape: 5-40 °C/41-104 °F, Portrait : 5-35 °C/41-95 20-80%(Without condensation)

-20-60 °C/-4-140 10-90%

967.6

stand:

967.6mm(W)

oss:

1170

48.5lbs/22 kg

52.47 lbs

68.78 8

Optional UL60950-1/C-UL/EN60950-1/FCC-B/IECS003-B/EN55024/EN61000-3-2/EN61000-3-3

/CE/NOM Support VESA DPMS convention

VESA

CD User's Clamper x

are

232

(Without

(W)x 559.6 mm(H)x 123.1mm(D)/38.09"

(W)x 715 mm(H)x 286 mm(D)

23.8

31.2

lbs

Holes

(400 mmpitches)

Multi-purpose

DDC2B,

Manual, QSG, Power Cord,VGA

x2(Topr

2, Main

switch

subjecttochange

°F

condensation)/90%-3.5%x(Temp-40°C) r

x605.6 mm

DDC/CI

cover.

(H)x 405 mm(D)/38.09"

Fix

Mount

event

from

falling),

without

Screw

notice.

70.87

Cable,

for

Main

(W)

Remote

switch

°F

egar

ding

x 22.03"

x23.84"

28.15

(H)

Contr coverx6, Screw

over

40°C

(H)

x 4.85"

(H)

x 15.95"

11.26

oller,AAA

(D)

Batteryx2,

for

CLAMPER

ViewSonic CD4233

Page 46

Customer Support

For technical support or product service, see the table below or contact your reseller. Note: You will need the product serial number.

Country/Region Web Site

Australia/New Zealand

Canada www.viewsonic.com

Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/Support/Calldesk.htm

Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.com

India www.in.viewsonic.com T= 1800 11 9999 service@in.viewsonic.com

Ireland (Eire)

Korea www.kr.viewsonic.com T= 080 333 2131 service@kr.viewsonic.com

Latin America (Argentina)

Latin America (Chile) www.viewsonic.com/la/ T=1230-020-7975 soporte@viewsonic.com

www.viewsonic.com.au

www.viewsoniceurope. com/uk/

www.viewsonic.com/la/ T= 0800-4441185 soporte@viewsonic.com

T=Telephone F=Fax

AUS=1800 880 818 NZ=0800 008 822

T (Toll-Free)= 1-866-463-4775 T (Toll)= 1-424-233-2533 F= 1-909-468-3757

www.viewsoniceurope.com/uk/ support/call-desk/

E-mail

service@au.viewsonic.com

service.ca@viewsonic.com

service_ie@viewsoniceurope.com

Latin America (Columbia)

Latin America (Mexico)

Renta y Datos, 29 SUR 721, COL. LA PAZ, 72160 PUEBLA, PUE. Tel: 01.222.891.55.77 CON 10 LINEAS Electroser, Av Reforma No. 403Gx39 y 41, 97000 Merida, Yucatan. Tel: 01.999.925.19.16 Other places please refer to http://www.viewsonic.com/la/soporte/index.htm#Mexico

Latin America (Peru) www.viewsonic.com/la/ T= 0800-54565 soporte@viewsonic.com

Macau www.hk.viewsonic.com T= 853 2870 0303 service@hk.viewsonic.com

Middle East ap.viewsonic.com/me/ Contact your reseller service@ap.viewsonic.com

Puerto Rico & Virgin Islands

Singapore/ Malaysia/ Thailand

South Africa ap.viewsonic.com/za/ Contact your reseller service@ap.viewsonic.com

www.viewsonic.com/la/ T= 01800-9-157235 soporte@viewsonic.com

www.viewsonic.com/la/ T= 001-8882328722 soporte@viewsonic.com

T= 1-800-688-6688 (English)

www.viewsonic.com

www.viewsonic.com.sg T= 65 6461 6044 service@sg.viewsonic.com

T= 1-866-379-1304 (Spanish) F= 1-909-468-3757

service.us@viewsonic.com soporte@viewsonic.com

United Kingdom

United States www.viewsonic.com

www.viewsoniceurope. com/uk/

www.viewsoniceurope.com/uk/ support/call-desk/

T (Toll-Free)= 1-800-688-6688 T (Toll)= 1-424-233-2530 F= 1-909-468-3757

service_gb@viewsoniceurope. com

service.us@viewsonic.com

ViewSonic CD4233

Page 47

Limited Warranty

VIEWSONIC LCD Commercial Display

What the warranty covers:

ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.

How long the warranty is effective:

ViewSonic LCD Commercial Displays are warranted for 3 years for all parts excluding the light source and 3 years for labor

IURPWKHGDWHRIWKH¿UVWFXVWRPHUSXUFKDVH

Who the warranty protects:

7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU

What the warranty does not cover:

1. $Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG

2. Damage, deterioration or malfunction resulting from: a. $FFLGHQWPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUHXQDXWKRUL]HGSURGXFWPRGL¿FDWLRQRU

failure to follow instructions supplied with the product.

b. Repair or attempted repair by anyone not authorized by ViewSonic. c. Any damage of the product due to shipment. d. Removal or installation of the product. e. &DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFSRZHUÀXFWXDWLRQVRUIDLOXUH f. 8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV g. Normal wear and tear. h. Any other cause which does not relate to a product defect.

3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is

displayed on the product for an extended period of time.

4. Removal, installation, and set-up service charges.

How to get service:

1. For information about receiving service under warranty, contact ViewSonic Customer Support (please refer to

Customer Support page). You will need to provide your product’s serial number.

2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your

address, (d) a description of the problem, and (e) the serial number of the product.

3. Take or ship the product freight prepaid in the original container to an authorized ViewSonic service center or

ViewSonic.

4. For additional information or the name of the nearest ViewSonic service center, contact ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein including the implied

ZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUDSDUWLFXODUSXUSRVH

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of use of

WKHSURGXFWORVV RIWLPHORVVRISUR¿WVORVVRIEXVLQHVV RSSRUWXQLW\ORVVRIJRRGZLOOLQWHUIHUHQFHZLWKEXVLQHVV

relationships, or other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

Effect of state law:

7KLVZDUUDQW\JLYHV\RXVSHFL¿FOHJDOULJKWVDQG\RXPD\DOVRKDYHRWKHUULJKWVZKLFKYDU\IURPVWDWHWRVWDWH6RPHVWDWHV

do not allow limitations on implied warranties and/or do not allow the exclusion of incidental or consequential damages, so the above limitations and exclusions may not apply to you.

Sales outside the U.S.A. and Canada:

For warranty information and service on ViewSonic products sold outside of the U.S.A. and Canada, contact ViewSonic or your local ViewSonic dealer. The warranty period for this product in mainland China (Hong Kong, Macao and Taiwan Excluded) is subject to the terms and conditions of the Maintenance Guarantee Card. For users in Europe and Russia, full details of warranty providedcan be found in www.viewsoniceurope.com under Support/Warranty Information.

4.3: ViewSonic LCD TV Warranty LTV_LW01 Rev. 1C 06-25-07

ViewSonic CD4233

Page 48

Mexico Limited Warranty

VIEWSONIC LCD Commercial Display

What the warranty covers:

How long the warranty is effective:

ViewSonic LCD Commercial Displays are warranted for 3 years for all parts excluding the light source and 3 years

IRUODERUIURPWKHGDWHRIWKH¿UVWFXVWRPHUSXUFKDVH

Who the warranty protects:

7KLVZDUUDQW\LVYDOLGRQO\IRUWKH¿UVWFRQVXPHUSXUFKDVHU

What the warranty does not cover:

 $Q\SURGXFWRQZKLFKWKHVHULDOQXPEHUKDVEHHQGHIDFHGPRGL¿HGRUUHPRYHG

2. Damage, deterioration or malfunction resulting from:

 D $FFLGHQWPLVXVHQHJOHFW¿UHZDWHUOLJKWQLQJRURWKHUDFWVRIQDWXUHXQDXWKRUL]HGSURGXFWPRGL¿FDWLRQ

unauthorized attempted repair, or failure to follow instructions supplied with the product.

b. Any damage of the product due to shipment.

 F &DXVHVH[WHUQDOWRWKHSURGXFWVXFKDVHOHFWULFDOSRZHUÀXFWXDWLRQVRUIDLOXUH  G 8VHRIVXSSOLHVRUSDUWVQRWPHHWLQJ9LHZ6RQLF¶VVSHFL¿FDWLRQV

e. Normal wear and tear. f. Any other cause which does not relate to a product defect.

3. Any product exhibiting a condition commonly known as “image burn-in” which results when a static image is displayed on the product for an extended period of time.

4. Removal, installation, insurance, and set-up service charges.

How to get service:

For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to the attached Customer Support page). You will need to provide your product’s serial number, so please record the product information in the space provided below on your purchase for your future use. Please retain your receipt of proof of purchase to support your warranty claim. For Your Records Product Name: ____________________________ Model Number: _______________________________ Document Number: ________________________ Serial Number: ________________________________ Purchase Date: ____________________________ Extended Warranty Purchase? ________________(Y/N) If so, what date does warranty expire? ______________

1. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product.

2. Take or ship the product in the original container packaging to an authorized ViewSonic service center.

3. Round trip transportation costs for in-warranty products will be paid by ViewSonic.

Limitation of implied warranties:

There are no warranties, express or implied, which extend beyond the description contained herein including the

LPSOLHGZDUUDQW\RIPHUFKDQWDELOLW\DQG¿WQHVVIRUDSDUWLFXODUSXUSRVH

Exclusion of damages:

ViewSonic’s liability is limited to the cost of repair or replacement of the product. ViewSonic shall not be liable for:

1. Damage to other property caused by any defects in the product, damages based upon inconvenience, loss of

XVHRIWKHSURGXFWORVVRIWLPHORVVRISUR¿WVORVVRIEXVLQHVVRSSRUWXQLW\ORVVRIJRRGZLOOLQWHUIHUHQFH

with business relationships, or other commercial loss, even if advised of the possibility of such damages.

2. Any other damages, whether incidental, consequential or otherwise.

3. Any claim against the customer by any other party.

4. Repair or attempted repair by anyone not authorized by ViewSonic.

ViewSonic CD4233

Page 49

Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico:

Name, address, of manufacturer and importers:

México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm

NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004

Hermosillo:

Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.P: 83140 Tel: 01-66-22-14-9005 E-Mail: disc2@hmo.megared.net.mx

Puebla, Pue. (Matriz):

RENTA Y DATOS, S.A. DE C.V. Domicilio: 29 SUR 721 COL. LA PAZ 72160 PUEBLA, PUE. Tel: 01(52).222.891.55.77 CON 10 LINEAS E-Mail: datos@puebla.megared.net.mx

Chihuahua

Soluciones Globales en Computación C. Magisterio # 3321 Col. Magisterial Chihuahua, Chih. Tel: 4136954 E-Mail: Cefeo@soluglobales.com

Distrito Federal:

QPLUS, S.A. de C.V. Av. Coyoacán 931 Col. Del Valle 03100, México, D.F. Tel: 01(52)55-50-00-27-35 E-Mail : gacosta@qplus.com.mx

Villahermosa:

Compumantenimietnos Garantizados, S.A. de C.V. AV. GREGORIO MENDEZ #1504 COL, FLORIDA C.P. 86040 Tel: 01 (993) 3 52 00 47 / 3522074 / 3 52 20 09 E-Mail: compumantenimientos@prodigy.net.mx

Veracruz, Ver.:

CONEXION Y DESARROLLO, S.A DE C.V. Av. Americas # 419 ENTRE PINZÓN Y ALVARADO Fracc. Reforma C.P. 91919 Tel: 01-22-91-00-31-67 E-Mail: gacosta@qplus.com.mx

Cuernavaca

Compusupport de Cuernavaca SA de CV Francisco Leyva # 178 Col. Miguel Hidalgo C.P. 62040, Cuernavaca Morelos Tel: 01 777 3180579 / 01 777 3124014 E-Mail: aquevedo@compusupportcva.com

Guadalajara, Jal.:

SERVICRECE, S.A. de C.V. Av. Niños Héroes # 2281 Col. Arcos Sur, Sector Juárez 44170, Guadalajara, Jalisco Tel: 01(52)33-36-15-15-43 E-Mail: mmiranda@servicrece.com

Guerrero Acapulco

GS Computación (Grupo Sesicomp) Progreso #6-A, Colo Centro 39300 Acapulco, Guerrero Tel: 744-48-32627

MERIDA:

ELECTROSER Av Reforma No. 403Gx39 y 41 Mérida, Yucatán, México CP97000 Tel: (52) 999-925-1916 E-Mail: rrrb@sureste.com

Tijuana:

STD Av Ferrocarril Sonora #3780 L-C Col 20 de Noviembre Tijuana, Mexico

4.3: ViewSonic Mexico Limited Warranty LTV_LW02 Rev. 1A 06-25-07

Monterrey:

Global Product Services Mar Caribe # 1987, Esquina con Golfo Pérsico Fracc. Bernardo Reyes, CP 64280 Monterrey N.L. México Tel: 8129-5103 E-Mail: aydeem@gps1.com.mx

Oaxaca, Oax.:

CENTRO DE DISTRIBUCION Y SERVICIO, S.A. de C.V. Murguía # 708 P.A., Col. Centro, 68000, Oaxaca Tel: 01(52)95-15-15-22-22 Fax: 01(52)95-15-13-67-00 E-Mail. gpotai2001@hotmail.com

FOR USA SUPPORT:

ViewSonic Corporation 381 Brea Canyon Road, Walnut, CA. 91789 USA Tel: 800-688-6688 (English); 866-323-8056 (Spanish); Fax: 1-800-685-7276 E-Mail: http://www.viewsonic.com

ViewSonic CD4233

Page 50

ViewSonic CD4233 User Guide

Specifications and Main Features

Frequently Asked Questions

User Manual