Vieta VNT7800BT User Manual

CONTENTS

SAFETY INFORMATION……………………………………………………..3

DISC NOTES………………………………..................……………………..5

INSTALLATION……………………………………………..............…….…..7

CONNECTIONS………...………………………………………….………...10

LOCA TIONS AND FUNCTION OF THE PLAYER………………….........11

LOCA TIONS AND FUNCTION OF THE REMOTE CONTROL…..….....13

BASIC OPERATION…………………………………………...…….….......16

MENU OPERATION…………………………………………………....…....18

RADIO OPERATION…………………………………………………….……….….…..18

DISC OPERATION……………………………………………………..……...…....…..21

BLUETOOTH OPERATION ..……………………………….………………....……....28

SD/USB OPERATION…………………………………………..……………….……...30

MY MUSIC OPERATON (IPOD OPERATION)..……......………….…..….………...30

AV IN OPERATION………………………………………………………………………31 REARVIEW OPERATION………………………………………………….…………...32

SETUP OPERATION…….……………………………………………….…..………….32

TROUBLE SHOOTING………………………………………...…....……....35

SPECIFICATIONS……………………………………………………..……..37

SAFETY INFORMATION

 Use This Product Safely

This unit has been designed and manufactured to assure personal safety. Improper use can result in electric shock or fire hazard. The safeguards incorporated in this unit protect you if you observe the following procedures for installation, use and servicing. This unit doesn’t contain any parts that can be repaired by the user.

When Driving

Keep the volume level low enough to be aware of road and traffic conditions. When Car Washing Do not expose the product to water or excessive moisture. This could cause electrical shorts, fire or other damage. When Parked Parking in direct sunlight can produce very high temperatures inside your vehicle. Give the interior a chance to cool down before starting playback. Use the Proper Power Supply This product is designed to operate with a 12 volt DC, negative ground battery system the regular system in a North American car). Protect the Disc Mechanism Avoid inserting any foreign objects into the slot of this player. Failure to observe this may cause malfunction due to the precise mechanism of this unit. Use Authorized Service Centers Do not attempt to disassemble or adjust this precision product. Please refer to the Service Center list included with this product for service assistance. For Installation The unit should be installed in a horizontal position with the front end up at a convenient angle, but not more than 300.

Protect the Monitor Mechanism The monitor is operated automatically. Do not draw the monitor out or turn it upward or downward manually. Otherwise, the mechanism construction may be harmed to some degree.

SAFETY INFORMATION

CAUTION:

MOBILE DVD PLAYER IS A CLASS I LASER PRODUCT. HOWEVER THIS MOBILE DVD PLAYER USES A VISIBLE/INVISIBLE LASE R BE AM WHICH COULD CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE THE MOBILE DVD PLAYER CORRECTLY AS INSTRUCTED. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND - DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL.

WARNING:

 TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS EQUIPMENT TO RAIN OR MOISTURE.

 TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, AND ANNOYING

INTERFERENCE, USE ONLY THE RECOMMENDED ACCESSORIES.

 THIS DEVICE IS INTENDED FOR CONTINUOUS OPERATION.

This product incorporates copyright protection technology that is protected by method

claims of certain U.S. patents and other intellectual property rights owned by

Macrovision Corporation and other rights owners. Use of this copyright protection

technology must be authorized by Macrovision Corporation, and is intended for home

and other limited viewing uses only unless otherwise authorized by Macrovision

Corporation. Reverse engineering or disassembly is prohibited.

Region Management Information

Region Management Information: This Mobile DVD Player is designed and

manufactured to respond to the Region Management Information that is recorded on

a DVD disc. If the Region number described on the DVD disc does not correspond to

the Region number of this Mobile DVD Player, this Mobile DVD Player cannot play

this disc.

DISC NOTES

Disc formats supported by this player

DVD 12 cm disc (Single-sided disc only)

Video CD 12 cm disc

Handling and Cleaning

 Dirt, dust, scratches and warping discs will cause wrong operation.  Do not place stickers or make scratches on discs.  Do not warp discs.

12 cm disc

MP3

12 cm disc

 A disc should always be kept in its case when not in use to prevent from damage.  Do not place discs in the following places:

1. Direct sunlight.

2. Dirty, dusty and damp areas.

3. Near car heaters.

4. On the seats or dashboard.

Disc Cleaning

Use a dry soft cloth to wipe the surface. If the disc is quite dirty, using a soft cloth slightly dip with isopropyl (rubbing) alcohol. Never use solvents such as benzine, thinner or conventional record cleaners as they may mar the surface of the disc.

Note:

A disc may become somewhat scratched (although not enough to make it unusable) depending on the way it is handled and conditions in the usage environment. Note these scratches are not an indication of any problem with the player.

DISC NOTES

Preparing New Discs with Rough Spots

A new disc may have rough edges on its inside and outside edges. If a disc with rough edges is used, the proper setting will not be performed and the player will not play the disc. Therefore, remove the rough edges in advance by using a ballpoint pen or pencil as shown on the right. To remove the rough edges, press the side of the pen or pencil against the inside and outside edges of the disc.

INSTALLATION

Notes:

 Choose the mounting location where

the unit will not interfere with the normal driving function of the driver.

 Before finally installing the unit,

connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly.

 Use only the parts included with the

unit to ensure proper installation. The use of unauthorized parts can cause malfunctions.

 Consult with your nearest dealer if

installation requires the drilling of holes or other modifications of the vehicle.

 Install the unit where it does not get

in the driver’s way and cannot injure the passenger if there is an emergency stop.

 If installation angel exceeds 30°from

horizontal, the unit might not give its optimum performance.

 Avoid installing the unit where it

would be subject to high temperature, such as from direct sunlight, or from hot air, from the heater, or where it would be subject to dust, dirt or excessive vibration.

DIN FRONT/REAR-MOUNT

This unit can be properly installed either from “Front”(conventional DIN Front-mount) or “Rear”(DIN Rear-mount installation, utilizing threaded screw holes at the sides of the unit chassis). For details, refer to the following illustrated installation methods.

DIN FRONT-MOUNT (Method A)

Installation Opening This unit can be installed in any dashboard having an opening as shown below:

Installing the unit Be sure you test all connections first, and then follow these steps to install the unit.

1. Make sure the ignition is turned off, and then disconnect the cable from the vehicle battery’s negative (-) terminal.

2. Disconnect the wire harness and the antenna.

3. Lift the top of the outer trim ring then pull it out to remove it.

4. Use the screwdriver to remove the four screws on the left and the right side of the unit then you can remove the sleeve.

Screwdriver

Screws

Outer Trim Ring

Sleeve

Unit

INSTALLATION

5. Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver. Not all tabs will be able to make contact, so examine which ones will be most effective. Bending open the appropriate tabs behind the dashboard to secure the sleeve in place.

(1) Dashboard (2) Taps

6. Reconnect the wire harness and the antenna and be careful not to pinch any wires or cables.

7. Slide the unit into the sleeve until it locks into place.

8. To further secure the unit, use the supplied metal strap to secure the back of the unit in place. Use the supplied hardware (Hex Nut (M5mm) and Spring Washer) to attach one end of the strap to the mounting bolt on the back of the unit. If necessary, bend the metal strap to fit your vehicle’s mounting area. Then use the supplied hardware (Tapping Screw and Plain Washer) to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard. This strap also helps ensure proper electrical grounding of the unit. Note to install the short threading terminal of the mounting bolt to the

back of the unit and the other long threading terminal to the dashboard.

(1) Metal Strap; (2) Mounting Bolt; (3) Hex Nut; (4) Spring Washer; (5) Tapping Screw; (6) Plain Washer

9. Reconnect the cable to the vehicle battery’s negative (-) terminal. Then replace the out trim ring.

Removing the unit

1. Make sure the ignition is turned off,

then disconnect the cable from the vehicle battery’s negative (-) terminal.

2. Remove the metal strap attached the

back of the unit (if attached).

3. Lift the top of the outer trim ring then

pull it out to remove it.

4. Remove the four screws on the left

and the right side of the unit then pull the unit out of the dashboard.

INSTALLATION

DIN REAR-MOUNT (Method B)

If your vehicle is a Nissan or Toyota, follow these mounting instructions. Use the screw holes marked T (Toyota), or N (Nissan) located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle.

Side View showing Screw Holes marked T, N or S

Screw

Factory Radio Mounting Bracket

Screw

Hook

To fasten the unit to the factory radio mounting brackets. Align the screw holes on the bracket with the screw holes on the unit, and then tighten the screws (5x5mm) on each side. Note: The outer trim ring, sleeve and the metal strap are not used for method B installation.

Dashboard or Console

CONNECTIONS

Line No.

1 Grey Video output (YELLOW) 2 Green Rearview input (YELLOW) 3 Green Subwoofer output (GREEN) 4 Brown Front RCA out right (RED) 5 Brown Front RCA out left (WHITE) 6 Grey Rear RCA out right (RED) 7 Grey Rear RCA out left (WHITE) 8 Black Radio antenna connector (BLACK)

Line color Function (terminal color)

LOCATIONS AND FUNCTION OF THE PLAYER

KEYS ON THE FRONT PANEL

WHEN REMOVING THE DETACHABLE PA NEL (press button (15) to remove it):

LOCATIONS AND FUNCTION OF THE PLAYER

1. OPEN: Press to draw out the monitor, when the monitor drawing out, press it to turn down the monitor and draw in.

2. BAND: Press it shortly to select radio band mode.

3. Disc Slot: Insert the disc into the disc slot to enter into DISC mode.

6. Volume knob/push SEL button: Repeatedly press to select the audio mode to adjust, such as

7. Remote sensor (IR): Receive signal from the remote control to control the unit.

9. SRC: In normal working status, press it to select the desired source mode, such as DISC,

10. TA/AF: Press it shortly to switch AF on or off. Hold press it to switch TA on or off.

11.

12&13.

14.

15. Release button: press to remove the button panel.

16. Reset button.

17. USB interface: Provide the interface for USB player.

18. AV IN jack: You can connect another audio/video system to the unit from this jack.

19. LCD: Display the current information on the display.

20. MIC: Microphone (for Bluetooth operation).

21. SD/MMC card interface.

: Press to answer the call or make a call in BT mode.

: Press to hang up the call.

VOL, BAS, TRE, BAL, FAD.

Rotate the knob to increase/decrease the volume level.

: In power off status, press it to turn the unit on. Press it for several seconds to turn off the unit. When the unit is on, press shortly to mute the sound, press it again to resume the sound.

RADIO, AV IN, SD/USB… etc.

/PTY: press it shortly to play/pause the playback. Hold press it to select the PTY program.

/ : When the monitor is drawing in, press to seek the radio stations, select the track

backward/forward, how to operation please refer to the contents below. When the monitor is drawing out, press the two buttons (TILT up/down) to adjust the monitor angle.

: Press to eject the disc that in the disc slot of the unit.

+ 28 hidden pages