Viessman VITOSOL 100-F, VITOSOL 200-F, VITOSOL 300-F Installation Instructions Manual

Installation instructions

for contractors

VIESMANN

Vitosol-F
Type SV and SH

Flat-plate collector for elevated installation

VITOSOL-F

5675 789 GB 2/2015

Dispose after installation.

2

Please follow these safety instructions closely to
prevent accidents and material losses.

Safety instructions explained

!

Please note

This symbol warns against the risk of material
losses and environmental pollution.

Note

Details identified by the word "Note" contain additional
information.

Target group

These instructions are exclusively intended for author­ised contractors.

Regulations to be observed

■

National installation regulations

■

Statutory regulations for the prevention of accidents

■

Statutory regulations for environmental protection

■

Codes of practice of the relevant trade associations

■

All relevant safety regulations as defined by DIN, EN,
DVGW, VDE and locally applicable standards

a

ÖNORM, EN and ÖVE

c

SEV, SUVA, SVTI, SWKI and SVGW

Safety instructions

5675 789 GB

3

1. Information Symbols ................................................................................................. 4

Intended use .......................................................................................... 4

Product information ................................................................................ 5

■

Collector support, standard kit and collector kit extension ................. 5

■

Retaining rail 6 for 1 collector ........................................................... 5

■

Retaining rail 7 for 2 collectors ......................................................... 6

■

Cross brace ........................................................................................ 6

■

Installation aid template ...................................................................... 6

2. Installation sequence Determining collector row clearance z ................................................... 8

Fitting the collector supports .................................................................. 8

Installing the cross braces ..................................................................... 10

Installing the collectors .......................................................................... 10

Connecting the collectors ...................................................................... 12

Installation .............................................................................................. 14

3. Commissioning .................................................................................................................. 16

Index

5675 789 GB

4

Symbol Meaning

Reference to other document containing
further information

1.

Step in a diagram:
The numbers correspond to the order in
which the steps are carried out.

Warning of material losses and environ­mental pollution

Live electrical area

Pay particular attention.

■

Component must audibly click into place.
or

■

Acoustic signal

■

Fit new component.
or

■

In conjunction with a tool: Clean the sur­face.

Dispose of component correctly.

Dispose of component at a suitable collec­tion point. Do not dispose of component in
domestic waste.

Intended use

The collectors provide central heating backup and
solar backup for DHW heating. They are only intended
to be installed and operated in sealed systems that
comply with EN 12976 and EN 12977, with due atten­tion paid to the associated installation, service and
operating instructions. Only operate the collectors with
heat transfer medium approved by the manufacturer.

Intended use presupposes that a fixed installation in
conjunction with permissible, system-specific compo­nents has been carried out.

Commercial or industrial usage for a purpose other
than heating a building or DHW shall be deemed inap­propriate.

Any usage beyond this must be approved by the man­ufacturer in each individual case.

Incorrect usage of the collectors or the installation sys­tem or incorrect operation is prohibited (e.g. the collec­tors being opened by the system user, failure to
observe the installation instructions). Failure to
observe these instructions can change functions,
endanger life and limb of the user or third parties and
will result in an exclusion of liability.
Incorrect usage also applies if components in the sys­tem are modified from their intended use (e.g. through
direct DHW heating in the collector).

Adhere to statutory regulations, especially concerning
the hygiene of potable water.

Symbols

5675 789 GB

5

Vitosol 100-F, 200-F and 300-F, types SV and SH, are
high performance flat-plate collectors.
The fixing system, with statically-tested and corrosion­resistant components made from stainless steel and
aluminium, is easy to assemble.

The following component assemblies are available for
collector types SV and SH, for a 30°, 45° or 60° angle
of collector inclination.

Collector support, standard kit and collector kit extension

■

Standard kit: 2 collector supports

■

Extension: 1 collector support

421 3 5

Fig.1

1

Collector support with footplates

2

Washer 7 8.4 mm

3

Hexagon bolt M 8 x 25

4

Clamping bracket

5

Self-tapping screw

Retaining rail 6 for 1 collector

6

Fig.2

Product information

5675 789 GB