Viega Eco Plus 8164.6 Instructions For Use Manual

Page 1
Viega Eco Plus WC element
Instructions for Use
for flush plates Visign
Model Year built:
8164.6 from 06/2007
en_INT
Page 2
Viega Eco Plus WC element 2 from 20
Page 3

Table of contents

Table of contents
1.1
1.2
1.3
Target groups 4
Labelling of notes 4
About this translated version 5
2 Product information 6
2.1
2.2
2.2.1
2.3
2.3.1
2.3.2
2.3.3
2.3.4
Standards and regulations 6
Intended use 6
Areas of use 6
Product description 7
Overview 7
Compatible components 7
Sound protection 9
Technical data 9
3 Handling 10
3.1
3.1.1
3.1.2
3.1.3
3.2
3.2.1
3.2.2
3.2.3
3.3
3.4
Assembly information 10
Mounting conditions 10
Installation dimensions 11
Required tools 11
Assembly 12
Connecting concealed cistern 12
Mounting WC element 14
Setting the flush volume 19
Cleaning and maintenance 20
Disposal 20
Viega Eco Plus WC element 3 from 20
Page 4
About these instructions for use

1 About these instructions for use

Trade mark rights exist for this document, further information can be found at viega.com/legal.

1.1 Target groups

The information in this instruction manual is directed at the following groups of people:
n Heating and sanitary professionals and trained personnel
It is not permitted for individuals without the abovementioned training or qualification to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
1.2
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER! This symbol warns against possible life-threatening injury.
WARNING! This symbol warns against possible serious injury.
CAUTION! This symbol warns against possible injury.
NOTICE! This symbol warns against possible damage to property.
Notes give you additional helpful tips.
Viega Eco Plus WC element 4 from 20
Page 5

1.3 About this translated version

This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e. g. EN) and/or in Germany (e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/ Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, stand‐ ards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
About these instructions for use
Viega Eco Plus WC element 5 from 20
Page 6

2 Product information

2.1 Standards and regulations

The following standards and regulations apply to Germany / Europe. National regulations can be found on the relevant web site of your country at viega.com/standards.
Regulations from section: Fields of application / Mounting conditions
Scope / Notice Regulations applicable in Ger‐
suitable masonry walls EN 1996-1-1
suitable concreted walls DIN 1045
Product information
many

2.2 Intended use

2.2.1 Areas of use

suitable support profiles DIN 18183
Regulations from section: Sound protection
Scope / Notice Regulations applicable in Ger‐
many
Fulfilled noise protection require‐ ments
Fulfilled noise protection require‐ ments
Fulfilled noise protection require‐ ments
The Viega Eco Plus WC element is suitable for mounting on masonry wall constructions and support profiles pursuant to the regulations in section Ä „Regulations from section: Fields of application / Mounting conditions“ on page 6.
DIN 4109
DIN 4109 (additional sheet 2)
VDI 4100 SSt I-SSt II
Viega Eco Plus WC element 6 from 20
Page 7

2.3 Product description

2
7
8
6
1
15
14
13
12
11
9
10
3
4
5

2.3.1 Overview

Product information
Fig. 1: Scope of delivery
1 - flush actuation site protection 2 - Viega Eco Plus WC element 3 - Viega concealed cistern 2H 4 - flushing pipe 5 - Four fixing heights for the WC ceramic: 330 mm / 350 mm /
370 mm / 390 mm 6 - drain 7 - adjustable feet 8 - drain elbow with reducer 9 - cistern lead-in 10 - threaded rods for fixing sanitary objects
(gauges for bore hole 180 or 230 mm) 11 - protective plug for drain 12 - protective plug for flushing pipe 13 - screws for fixing onto support profile 14 - fixing material for floor fixing 15 - fixing set

2.3.2 Compatible components

The WC element is compatible with all common WC ceramics, even with larger projection (barrier-free).
Viega Eco Plus WC element 7 from 20
Page 8
Fixing element
Connection installation set
Product information
The WC element can be extended by the following compatible compo‐ nents:
n fixing element (model 8169 and 8169.2) n odour extraction via flushing pipe (model 8310.26) n connection installation set (model 8350.14)
Mount the components in accordance with the instructions for use of the components.
The fixing element is suitable for barrier-free installation. Supports and handles can be mounted on the fixing element. The construction height of the fixing element is 1130 mm.
Compatible flush plates
The installation set is suitable for the connection of an electrical actua‐ tion. The installation set consists of an empty pipe, a cavity wall socket and the relative, required clip. The empty pipe connects the cavity wall socket with the concealed cistern.
Product Name Model
Standard Flush plate Standard 1 8180.1
Visign for Style Flush plate
8315.1
Visign for Style 10
Flush plate
8331.1
Visign for Style 11
Flush plate
8332.1
Visign for Style 12
Flush plate
8332.4
Visign for Style 12
Flush plate
8333.1
Visign for Style 13
Flush plate
8334.1
Visign for Style 14
Functional unit 8332.3
Visign for More Flush plate Visign for More
8352.1
100
Flush plate Visign for More
8351.1
101
Flush plate Visign for More
8353.1
102
Viega Eco Plus WC element 8 from 20
Page 9
Product Name Model
Product information
Flush plate Visign for More 103
Flush plate Visign for More 104
Visign for Care sensitive
Visign for More sensitive
Visign for Public Flush plate
Flush plate sensitive Visign for Care
Flush plate sensitive Visign for More 100
Flush plate sensitive Visign for More 100
Flush plate sensitive Visign for More 103
Flush plate sensitive Visign for More 103
Visign for Public 1
Flush plate Visign for Public 2
Flush plate Visign for Public 5
8355.1
8354.1
8352.21
230 V 8352.11
6.5 V 8352.12
230 V 8355.11
6.5 V 8355.12
8326.1
8327.1
8326.16

2.3.3 Sound protection

2.3.4
Flush volume
Technical data
Flush plate Visign for Public 6
Remote actuation Visign for Public 1
Cover plate Visign for Public 8326.9
The WC element complies with the noise insulation requirements speci‐ fied in section Ä „Regulations from section: Sound protection“ on page 6.
Small flush volume Factory setting approx. 3 l
Setting range approx. 3–4 l
Large flush volume Factory setting approx. ca. 6 l
8326.15
8326.21
Setting range approx. 6–9 l
Viega Eco Plus WC element 9 from 20
Page 10

3 Handling

3.1 Assembly information

3.1.1 Mounting conditions

Suitable walls
The Viega WC element is suitable for mounting on masonry wall con‐ structions and support profiles pursuant to the regulations in section
Ä
tions“ on page 6.
The WC element may only be mounted on even wall surfaces.
Construction height
With the construction height, the marked height of the upper edge of the finished floor must be observed.
Handling
„Regulations from section: Fields of application / Mounting condi‐
Installation depth
WC ceramic
Actuation
The installation depth can be between 130 mm and 200 mm.
The WC element can only be used in combination with wall-hung WCs (fixing gauges for bore hole 180 mm or 230 mm).
The WC element can be extended by a remote actuation Visign for Public1 (model 8326.21) or by an electronic actuation (model
8350.31 or 8350.32), as well as by sensitive flush plates (model 8352.21,
8352.11 and 8355.11). The corresponding actuation method must be prepared before the WC element is clad and tiled.
The corresponding empty pipe (included in the scope of delivery of the remote actuation) is required when preparing the remote actuation Visign for Public1.
Viega Eco Plus WC element 10 from 20
Page 11

3.1.2 Installation dimensions

Handling

3.1.3 Required tools

Fig. 2: Viega Eco Plus WC element 8164.6 dimensions
The following tools are required for mounting the WC element:
n drill with 10 mm drill bit n ratchet with sockets: 13 mm / 17 mm n fork or ring spanner: 27 mm
Viega Eco Plus WC element 11 from 20
Page 12

3.2 Assembly

3.2.1 Connecting concealed cistern

Pull the water supply pipe with the protective pipe into the cistern through the hole on the left.
Handling
Insert the cistern lead-in around the water supply pipe. Insert the protective pipe into the cistern lead-in only up to the middle of the pipe.
Compress the cistern lead-in.
Mount the matching screw fitting for the respective pipe system.
Screw the corner valve tight.
Viega Eco Plus WC element 12 from 20
Page 13
Handling
Push the cistern lead-in with the mounted Viega corner valve into the cistern wall.
Insert the Viega screw fitting comprised in the delivery into the cis‐ tern lead-in.
Guide the filling hose through the lugs in the top of the cistern.
Mount the filling valve hose to the corner valve.
Before commissioning the cistern, flush the water supply pipe.
Viega Eco Plus WC element 13 from 20
Page 14

3.2.2 Mounting WC element

X3
0-200
X1
X2
0
Ø10
560638_B2
13
0-200
0
X
17
Masonry wall
Handling
Determine and mark fixing points.
n X1: 390 mm (model 8180.73) n X2: 440 mm (model 8173) n X3: At a construction height of 1130 mm, the size is 1110 mm.
Drill holes.
Fill drill holes and dowels with silicone.
Mount the fixing set with the fork spanner (size 13).
Align the height of the feet.
Check WC element on cutting check.
Mark fixing points on the floor.
Viega Eco Plus WC element 14 from 20
Page 15
0-200
0
X
17
Ø10
Handling
Align WC element.
Set the installation depth of the pre-wall element (130–200 mm) with the fork spanner (size 17).
Remove WC element and drill floor holes.
Fill drill holes with silicone.
Insert dowels.
Fill dowels with silicone.
Attach the element.
Optionally, screw feet onto wooden beams.
Viega Eco Plus WC element 15 from 20
Page 16
Clip in drain elbow.
click
Insert protective plug.
If necessary, mount a reducer.
Handling
Screw in the threaded rods for WC ceramic to the desired height.
Pull the plastic protective sleeves for the threaded rods over the WC ceramic.
Double-clad WC element with IFGP cladding panels (model
8055.10) (2 x 12.5 mm).
Viega Eco Plus WC element 16 from 20
Page 17
On-site support profile
Ø10
13
90°
5
0
7
5
Handling
Align WC element and secure the height of the feet with a fork spanner (size 13).
Determine the fixing points.
Drill holes.
Pull out the foot and if necessary, adjust (pre-mounted) foot depth from 75 mm to 50 mm.
Fill drill holes with silicone.
Insert dowels.
Fill dowels with silicone.
Attach the element.
Viega Eco Plus WC element 17 from 20
Page 18
Determine construction height in accordance with the on-site
0-200
0
1000
8x
click
marking of the upper edge of the finished floor.
Attach WC element to the support profiles.
Handling
Clip in drain elbow.
Insert protective plug.
Screw in the threaded rods for WC ceramic to the desired height.
Viega Eco Plus WC element 18 from 20
Page 19

3.2.3 Setting the flush volume

Handling
Double-clad WC element with IFGP cladding panels (model
8055.10) (2 x 12.5 mm).
Immediate re-flushing of the flush volume is possible at the factory settings.
Small flush volume
Large flush volume
The WC element is factory-set at a small flush of approx. 3 l. The small flush volume can be set at three levels: approx. 3 l / 3.5 l / 4 l.
Remove the drain valve from the concealed cistern.
Push the slide control on the side of the overflow pipe to the desired small flush volume:
n Top position: approx. 3 l n Middle position: approx. 3.5 l n Bottom position: approx. 4 l
The positions can be identified by the notches.
The WC element is factory-set at a large flush volume of approx. 6 l. The large flush volume can be set continuously from approx. 6 l up to approx. 9 l.
Remove the drain valve from the concealed cistern.
Viega Eco Plus WC element 19 from 20
Page 20
Push the slide control below the drain valve to the desired large flush volume:
n left: approx. 6 l n right: approx. 9 l

3.3 Cleaning and maintenance

Handling
Cleaning and maintenance of the concealed cistern
In consideration of the mechanical, chemical and physical conditions, the concealed cistern is constantly laden. For this reason, the components must be cleaned, as required, and the drain and filling valve seals renewed.
In areas or regions with hard water due to calcium or magnesium salts, there is the risk of limescale deposits developing on the inlet and drain valves. The valves may have to be replaced, depending on the extent of deposits.
3.4
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.
Viega Eco Plus WC element 20 from 20
Loading...