for fitting holders 8062.1, 8063.0, 8064,
Urinal module 8119.3, 8126
ModelYear built:
8162.5from 01/2013
en_INT
Page 2
Viega Eco Plus basic element2 from 11
Page 3
Table of contents
1About these instructions for use4
Table of contents
1.1
1.2
1.3
Target groups4
Labelling of notes4
About this translated version5
2Product information6
2.1
2.1.1
2.2
2.2.1
Intended use6
Areas of use6
Product description6
Overview6
3Handling7
3.1
3.1.1
3.1.2
3.2
3.2.1
3.3
Assembly information7
Installation dimensions7
Required tools7
Assembly8
Mounting base element8
Disposal11
Viega Eco Plus basic element3 from 11
Page 4
About these instructions for use
1About these instructions for use
Trade mark rights exist for this document, further information can be
found at viega.com/legal.
1.1Target groups
The information in this instruction manual is directed at the following
groups of people:
n Heating and sanitary professionals and trained personnel
n Drywall builder
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, service this product. This
restriction does not extend to possible operating instructions.
1.2
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
Viega Eco Plus basic element4 from 11
Page 5
1.3About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand‐
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Viega Eco Plus basic element5 from 11
Page 6
2Product information
2
1
3
2.1Intended use
2.1.1Areas of use
The Viega Eco Plus base element is suitable for:
n Fitting holders model 8062.1 and model 8063.0
n Urinal module model 8119.3 and model 8126
The Viega Eco Plus base element is not suitable for:
n Viegaswift bidet module model 8130.3
n Viegaswift WC module model 8039.3
Product information
2.2Product description
2.2.1Overview
Fig. 1: Component overview
1 - Viega Eco Plus base element
2 - fixing screws of the adjustable feet
3 - adjustable feet
Viega Eco Plus basic element6 from 11
Page 7
3Handling
3.1Assembly information
3.1.1Installation dimensions
Handling
Fig. 2: Dimensions model 8162.5
3.1.2Required tools
The following tools are required for mounting:
n drill with 10 mm drill bit
n fork or ring spanner: 13 mm / 17 mm
Viega Eco Plus basic element7 from 11
Page 8
3.2Assembly
X3
0-200
X1
X2
0
Ø10
560638_B2
13
0-200
0
1000
1
7
3.2.1Mounting base element
Masonry wall
Handling
Determine and mark fixing points.
n X1: 390 mm (model 8180.73)
n X2: 440 mm (model 8173)
n X3: possible construction heights (depending on length of ele‐
ment): 960 mm, 1110 mm or 1280 mm
Observe construction height in accordance with the on-site marking
of the upper edge of the finished floor.
Drill holes (10 mm).
Mount the fixing set with the fork spanner (size 13).
Determine construction height in accordance with the on-site
marking of the upper edge of the finished floor.
Align the height of the feet with a fork spanner (size 17).
INFO! The construction height must be determined and
adhered to exactly.
There are only limited possibilities available to remedy errors
made during this assembly step, Ä Chapter 3.1.1 „Installation
dimensions“ on page 7.
Mark fixing points on the floor.
Viega Eco Plus basic element8 from 11
Page 9
Set installation depth of the base element using a fork spanner
17
0-200
0
x
Ø10
13
0-200
0
(size 17).
x = depending on the fitting holder or urinal module used
Remove base element and drill floor holes (10 mm).
Handling
Attach base element to the floor using the fork spanner (size 13) and
the screws and dowels supplied.
Double clad base element with IFGP cladding panels (model
8055.10) (2 x 12.5 mm).
Viega Eco Plus basic element9 from 11
Page 10
On-site support profile
90°
5
0
75
Ø10
13
0-200
0
1000
Handling
If necessary, adjust feet from 75 mm to 50 mm (pull out and turn).
Drill floor holes (10 mm).
Attach base element to the floor using the screws and dowels sup‐
plied (size 13).
Determine construction height in accordance with the on-site
marking of the upper edge of the finished floor.
Align base element upwards, observe installation height marking.
INFO! The construction height must be determined and
adhered to exactly.
There are only limited possibilities available to remedy errors
made during this assembly step, Ä Chapter 3.1.1 „Installation
dimensions“ on page 7.
Viega Eco Plus basic element10 from 11
Page 11
8x
Handling
Attach base element flush in the support profiles using the screws
supplied.
Double-clad base element with IFGP cladding panels
(model 8055.10) (2 x 12.5 mm).
3.3
Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Viega Eco Plus basic element11 from 11
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.