Page 1
Viega Eco Plus urinal element siphon sensor
technology
Instructions for Use
for urinal with siphon sensor technology
Model Year built:
8152.4 from 06/2015
en_INT
Page 2
Viega Eco Plus urinal element siphon sensor technology 2 from 16
Page 3
Table of contents
1 About these instructions for use 4
Table of contents
1.1
1.2
1.3
Target groups 4
Labelling of notes 4
About this translated version 5
2 Product information 6
2.1
2.2
2.2.1
2.3
2.3.1
2.3.2
2.3.3
2.3.4
2.4
Standards and regulations 6
Intended use 6
Areas of use 6
Product description 7
Overview 7
Compatible components 7
Sound protection 8
Technical data 8
Accessories 8
3 Handling 9
3.1
3.1.1
3.1.2
3.1.3
3.2
3.2.1
3.3
Assembly information 9
Mounting conditions 9
Installation dimensions 9
Required tools 10
Assembly 10
Mounting the urinal element 10
Disposal 16
Viega Eco Plus urinal element siphon sensor technology 3 from 16
Page 4
About these instructions for use
1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
n Heating and sanitary professionals and trained personnel
n Trained electricians
n Drywall builder
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
viega.com/legal
.
1.2 Labelling of notes
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
Viega Eco Plus urinal element siphon sensor technology 4 from 16
Page 5
1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Viega Eco Plus urinal element siphon sensor technology 5 from 16
Page 6
2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe.
National regulations can be found on the relevant web site of your
country at
Regulations from section: Fields of application / Mounting conditions
Scope / Notice Regulations applicable in Ger-
suitable masonry walls EN 1996-1-1
suitable support profiles DIN 18183
viega.com/standards
Product information
.
many
2.2 Intended use
2.2.1 Areas of use
Regulations from section: Sound protection
Scope / Notice Regulations applicable in Ger-
many
Fulfilled noise protection requirements
Fulfilled noise protection requirements
Fulfilled noise protection requirements
The Viega Eco Plus urinal element "siphon sensor technology" is suitable for mounting on masonry wall constructions and support profiles
pursuant to the regulations in section
Fields of application / Mounting conditions“ on page 6
The urinal element is intended for use with the equipment set model
8352.2
Ä Chapter 2.3.2 „Compatible components“ on page 7
DIN 4109
DIN 4109 (additional sheet 2)
VDI 4100 SSt I-SSt II
Ä „Regulations from section:
.
.
Viega Eco Plus urinal element siphon sensor technology 6 from 16
Page 7
2.3 Product description
6
5
4
3
1
2
9
8
7
2.3.1 Overview
Product information
Fig. 1: Components
1 - urinal installation set
2 - threaded bolts for fixing sanitary objects
3 - adjustable feet
4 - drain elbow
5 - mounting bracket for drain elbow
6 - Viega Eco Plus element (8152.4)
7 - wall plate Rp ½
8 - double nipple R ½
2.3.2 Compatible components
9 - fixing set, model 8173*
* not included in scope of delivery
The urinal element is compatible with the equipment set "Siphon sensor
technology" model 8352.2.
It is suitable for all ceramics with a horizontal connection.
Viega Eco Plus urinal element siphon sensor technology 7 from 16
Page 8
2.3.3 Sound protection
2.3.4 Technical data
Product information
The urinal element complies with the noise insulation requirements
specified in section
on page 6
The product has the following technical data:
.
Ä „Regulations from section: Sound protection“
2.4 Accessories
Required accessories
drain elbow DN 50
Fitting connection Rp ½
Hole diameter for fixing in wooden
frame construction
Maximum height of urinal inlet
from upper edge of the finished
floor
The fixing set model 8173 is required to secure.
11 mm
880 mm
Viega Eco Plus urinal element siphon sensor technology 8 from 16
Page 9
3 Handling
3.1 Assembly information
3.1.1 Mounting conditions
Construction height
With the construction height, the marked height of the upper edge of
the finished floor must be observed.
Actuation
The urinal element can be extended with the equipment set "Siphon
sensor technology", model 8352.2.
Handling
3.1.2 Installation dimensions
Urinal element
Fig. 2: Dimensions
Viega Eco Plus urinal element siphon sensor technology 9 from 16
Page 10
3.1.3 Required tools
X3
0-200
X1
X2
0
Ø10
n drill with 10 mm drill bit
n ratchet with sockets: 13 mm / 17 mm
n fork or ring spanner: 13 mm / 17 mm / 22 mm
3.2 Assembly
3.2.1 Mounting the urinal element
Handling
DANGER!
Danger due to electrical current
An electric shock can lead to burns and serious injury and
even death.
Masonry wall
– Work on the electrics may only be carried out by trained
electricians.
– Always de-energise the connection line before work is
commenced.
Masonry and concreted walls
You should use a support bracket (model 8165) when
mounting multiple urinal elements with an interval of
> 490 mm. Observe the instructions for use of the support
bracket when mounting.
Determine and mark fixing points.
n
X1: 390 mm (model 8180.73)
n X2: 440 mm (model 8173)
n X3: 1100 mm
Viega Eco Plus urinal element siphon sensor technology 10 from 16
Page 11
560638_B2
13
1,0 m
0
0-2
0
0 mm
x
x
x
x
0
17
17
0-200
m
m
x
13
Handling
Drill holes.
Mount the fixing set with the fork spanner (size 13).
Align the height of the urinal element in accordance with the cutting
check.
Determine construction height in accordance with the on-site
marking of the upper edge of the finished floor.
x = Observe the instructions of the urinal manufacturer.
INFO! The construction height must be determined and
adhered to exactly.
There are only limited possibilities available to remedy errors
made during this assembly step,
on page 9
.
Ä „Construction height“
Set the installation depth of the pre-wall element with the fork
spanner (size 17).
Attach urinal element to the floor using the fork spanner (size 13)
and the screws and dowels supplied.
Viega Eco Plus urinal element siphon sensor technology 11 from 16
Page 12
Mount drain elbow in mounting bracket.
0
50
6
50 -100
max. 390
17
22
22
Secure with a bracket.
Set height of the drain elbow (50 mm)
Mount threaded bolts.
Handling
Seal double nipple from one side.
Screw double nipple into the wall plate.
Secure water inlet onto the double nipple.
Viega Eco Plus urinal element siphon sensor technology 12 from 16
Page 13
0
0-200 mm
Handling
Seal supply fitting.
Screw supply fitting into the wall plate.
DANGER! Risk of electric shock. Work on the electrics may only
be carried out by trained electricians.
Lay the electrical cable in the installation set.
Mounting in Viega Eco Plus
Connect water line.
Double-clad urinal element (2 x 12.5 mm).
The urinal element can be installed in support profiles of 50 mm and
75 mm.
Determine the fixing points.
Align element.
Mount drain elbow, double nipple and water inlet.
Viega Eco Plus urinal element siphon sensor technology 13 from 16
Page 14
75
m
m
50
m
m
13
x
x
1,
0 m
0
0
-
2
0
0
mm
x
x
4x
4x
Handling
If necessary, adjust the pre-mounted feet from 75 mm to 50 mm:
Pull the foot out and turn by 90°.
Attach urinal element to the floor using the fork spanner (size 13)
and the screws and dowels supplied.
Determine construction height in accordance with the on-site
marking of the upper edge of the finished floor.
Pull urinal element up (cutting check) and align.
x = Observe the instructions of the urinal manufacturer.
INFO! The construction height must be determined and
adhered to exactly.
There are only limited possibilities available to remedy errors
made during this assembly step,
on page 9
.
Ä „Construction height“
Screw the urinal element together laterally with the support profiles.
Viega Eco Plus urinal element siphon sensor technology 14 from 16
Page 15
x
x
x
x
max. 390
0
0
-
200
mm
Handling
Connect water line.
DANGER! Risk of electric shock. Work on the electrics may only
be carried out by trained electricians.
Lay the electrical cable in the installation set.
Double-clad urinal element (2 x 12.5 mm).
Mounting in Viega Steptec
Align urinal module.
INFO! Observe the ceramic manufacturer's information when
aligning the connections.
If necessary, swap the installation set with the mounting bracket and
the crossbeam of the threaded bolts with each other.
Mount drain elbow, double nipple and water inlet.
Viega Eco Plus urinal element siphon sensor technology 15 from 16
Page 16
Handling
Secure the module onto the open side of the Steptec rail with the
slot nuts supplied.
Press the slot nut in gently and secure in the open rail side with a
90° turn.
If necessary, align the height of the urinal element.
Tighten slot nut with a fork spanner (size 17).
Connect water line.
DANGER! Risk of electric shock. Work on the electrics may only
be carried out by trained electricians.
3.3
Lay the electrical cable in the installation set.
Clad urinal element (1 x 12.5 mm).
Afterwards, install the sensor technology and the urinal. You will find
information regarding the procedure in the instructions for use of the
equipment set model 8352.2 and of the urinal.
Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Viega Eco Plus urinal element siphon sensor technology 16 from 16
Loading...