Page 1
Advantix shower channel mounting frame
Instructions for Use
For mounting with an Advantix shower channel
Model
4982.45
en_INT
Page 2
Advantix shower channel mounting frame 2 from 9
Page 3
Table of contents
1 About these instructions for use 4
Table of contents
1.1
1.2
1.3
Target groups 4
Labelling of notes 4
About this translated version 5
2 Product information 6
2.1
2.2
2.2.1
Standards and regulations 6
Product description 6
Overview of the components 6
3 Handling 7
3.1
3.1.1
3.1.2
3.2
3.3
Assembly information 7
Important note 7
Installation dimensions 7
Assembly 8
Disposal 9
Advantix shower channel mounting frame 3 from 9
Page 4
About these instructions for use
1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
n Heating and sanitary professionals and trained personnel
n Tilers
Individuals without the abovementioned training or qualification are not
permitted to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
.
1.2 Labelling of notes
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
Advantix shower channel mounting frame 4 from 9
Page 5
1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, standards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Advantix shower channel mounting frame 5 from 9
Page 6
2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe.
National regulations can be found on the relevant web site of your
country at
Regulations from section: Media
Scope / Notice Regulations applicable in Ger-
Typical domestic wastewater DIN 1986-3
viega.com/standards
Product information
.
many
2.2 Product description
Advantix mounting frames are suitable for use in Advantix shower channels base unit model 4982.10 and 4982.20.
Advantix mounting frames are suitable for all Advantix shower channel
grates with a layer height of 12-15 mm (tile and adhesive).
Only wastewater commonly encountered in households may be introduced, see
Observe the instructions for use of the base unit when mounting.
2.2.1 Overview of the components
Ä „Regulations from section: Media“ on page 6
.
Fig. 1: Components and scope of delivery
Advantix mounting frame for stainless steel 1.4301 Advantix shower
channel
Advantix shower channel mounting frame 6 from 9
Page 7
3 Handling
3.1 Assembly information
3.1.1 Important note
During assembly:
n Observe installation dimensions.
After assembly:
n The shower channel must be fully lined with mortar.
n Coordinate all relevant installation details, especially regarding the
Handling
bonded sealing, with those responsible for the subsequent work.
3.1.2 Installation dimensions
Fig. 2: Dimensions
Model Art. no. Length
4982.45 745 356
745 363
745 370
750
800
900
745 387
745 394
Advantix shower channel mounting frame 7 from 9
1000
1200
Page 8
3.2 Assembly
12
15
Handling
Requirements:
n The shower channel has been mounted according to the instructions
for use.
n The complete surface of the shower channel has been lined.
n The shower channel has been sealed, and the thin bed sealing is
fully cured.
n The shower channel is equipped with a protective insert.
Apply the tile adhesive.
Mounting height 12 mm: Press the tile end rail down into the tile
adhesive as far as it will go.
Mounting height 15 mm: Set the tile end rail onto a tile adhesive bed
of a thickness of max. 3 mm.
Advantix shower channel mounting frame 8 from 9
Page 9
589379_B4
589379_B4
Handling
Remove the protective insert.
If a gap has formed at the inside of the shower channel, seal it with
tile adhesive or joint filler.
3.3
Regarding mounting of the grate, refer to the instructions for use for
the grate.
Disposal
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Advantix shower channel mounting frame 9 from 9
Loading...