Page 1
Prevista Dry Plus fitting holder for wallmounted fitting, reinforced
Instructions for Use
for wall-mounted fitting
Model Year built:
8555.31 from 01/2019
en_INT
Page 2
Prevista Dry Plus fitting holder for wall-mounted fitting, reinforced 2 from 10
Page 3
Table of contents
1 About these instructions for use 4
Table of contents
1.1
1.2
1.3
Target groups 4
Labelling of notes 4
About this translated version 5
2 Product information 6
2.1
2.2
2.2.1
2.3
2.3.1
2.3.2
Standards and regulations 6
Intended use 6
Areas of use 6
Product description 7
Overview 7
Compatible components 7
3 Handling 8
3.1
3.1.1
3.2
3.2.1
3.2.2
3.3
Assembly information 8
Installation dimensions 8
Assembly 8
Mounting module 8
Rounding off jobs 10
Disposal 10
Prevista Dry Plus fitting holder for wall-mounted fitting, reinforced 3 from 10
Page 4
About these instructions for use
1 About these instructions for use
Trade mark rights exist for this document; for further information, go to
viega.com/legal.
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
n Heating and sanitary professionals and trained personnel
n Consumers
Individuals without the abovementioned training or qualification are not
permitted to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.
1.2
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
Labelling of notes
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns of possible life-threatening injury.
WARNING!
This symbol warns of possible serious injury.
CAUTION!
This symbol warns of possible injury.
NOTICE!
This symbol warns of possible damage to property.
This symbol gives additional information and hints.
Prevista Dry Plus fitting holder for wall-mounted fitting, reinforced 4 from 10
Page 5
1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e.g. EN) and/or in Germany
(e.g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand‐
ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.
About these instructions for use
Prevista Dry Plus fitting holder for wall-mounted fitting, reinforced 5 from 10
Page 6
2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe and
are provided as a support feature.
Regulations from section: Fields of application / Mounting conditions
Scope / Notice Regulations applicable in Ger‐
Suitable masonry walls EN 1996-1-1
Suitable concreted walls DIN 1045
Product information
many
2.2 Intended use
2.2.1 Areas of use
The fitting holder is suitable for mounting on wall constructions pursuant
to the regulations in section Ä „Regulations from section: Fields of
application / Mounting conditions“ on page 6 and is intended for use in
a Prevista Dry Plus pre-wall construction.
Prevista Dry Plus fitting holder for wall-mounted fitting, reinforced 6 from 10
Page 7
2.3 Product description
2.3.1 Overview
Product information
Fig. 1: Scope of delivery
1 Fitting holders
2 Screws for fixing in support profile
3 slot nuts
4 connections for wall plates
2.3.2 Compatible components
The fitting holder is intended for use with a wall-mounted fitting.
Prevista Dry Plus fitting holder for wall-mounted fitting, reinforced 7 from 10
Page 8
3 Handling
3.1 Assembly information
3.1.1 Installation dimensions
Handling
Fig. 2: Installation dimensions
3.2 Assembly
3.2.1 Mounting module
Prevista Dry Plus fitting holder for wall-mounted fitting, reinforced 8 from 10
Use the slot nuts supplied to attach the fitting holder to the open
mounting rail.
Insert the slot nut into the opening of the module.
Page 9
Push the slot nut in until it engages.
25 Nm
Set the height of the rail.
Handling
Fasten the slot nut.
Bend the sides of the metal bars of the fitting holder.
Prevista Dry Plus fitting holder for wall-mounted fitting, reinforced 9 from 10
Page 10
9
İ
Handling
Attach the wall plate fixings and the wall plates.
Set the height of the fitting holder according to the information of
the sanitary item manufacturer.
3.2.2 Rounding off jobs
3.3
Disposal
Clad the pre-wall with suitable gypsum cardboard cladding panels.
Make sure that no abutting edges converge.
Grout the abutting edges and joints with a suitable filler.
For more detailed information, observe the mounting instructions for
the gypsum cardboard cladding panels.
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Prevista Dry Plus fitting holder for wall-mounted fitting, reinforced 10 from 10
Loading...