Page 1
Radio receiver
Instructions for Use
for the reception of a flush actuation via radio signal
Model Year built:
8350.35 from 06/2012
en_INT
Page 2
Radio receiver 2 from 10
Page 3
Table of contents
1 About these instructions for use 4
Table of contents
1.1
1.2
1.3
Target groups 4
Labelling of notes 4
About this translated version 5
2 Product information 6
2.1
2.1.1
2.2
2.2.1
2.2.2
2.2.3
Intended use 6
Areas of use 6
Product description 6
Overview 6
Operating mode 6
Extensions 7
3 Handling 8
3.1
3.2
3.3
Assembly 8
Commissioning 9
Disposal 10
Radio receiver 3 from 10
Page 4
About these instructions for use
1 About these instructions for use
Trade mark rights exist for this document, further information can be
found at
1.1 Target groups
The information in this instruction manual is directed at the following
groups of people:
n Heating and sanitary professionals and trained personnel
It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, service this product. This
restriction does not extend to possible operating instructions.
viega.com/legal
.
1.2 Labelling of notes
The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.
Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.
DANGER!
This symbol warns against possible life-threatening injury.
WARNING!
This symbol warns against possible serious injury.
CAUTION!
This symbol warns against possible injury.
NOTICE!
This symbol warns against possible damage to property.
Notes give you additional helpful tips.
Radio receiver 4 from 10
Page 5
1.3 About this translated version
This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The pertinent national laws, standards, regulations and guidelines, as well as other technical guidelines,
have priority over German/European guidelines in this manual: The
information is not binding for other countries and territories and should,
as mentioned, be considered as support.
About these instructions for use
Radio receiver 5 from 10
Page 6
2 Product information
3
2
1
2.1 Intended use
2.1.1 Areas of use
The radio receiver may only be used with the following Viega products:
Compatible WC flush plates:
n Visign for Public 5, model 8326.16
n Visign for Public 6, model 8326.15
n Visign for Care sensitive, model 8352.21
n Visign for More 100 sensitive, model 8352.11
n Visign for More 100 sensitive, model 8352.12
n Visign for More 103 sensitive, model 8355.11
n Visign for More 103 sensitive, model 8355.12
Product information
2.2 Product description
2.2.1 Overview
Compatible WC flush actuation:
n Model 8350.31
n Model 8350.32
n Model 8350.33
n Model 8350.34
Fig. 1: Radio receiver 8350.35
1 - programming button
2 - LED
3 - connection adapter
2.2.2 Operating mode
Signals to actuate the flush (e. g. on support hinged handles) sent by
Radio receiver 6 from 10
HEWI radio transmitters can be received by the radio receiver.
Up to 32 receivers can be connected to a radio receiver.
Page 7
2.2.3 Extensions
Fig. 2: Extension cable adapter model
8350.36
Product information
Multiple sensors can be connected to a control at the same time using
the extension cable adapter model 8350.36. This is how e. g. a button
can be combined with the radio receiver.
Fig. 3: Connection diagram for radio and
cable sensors
Radio receiver 7 from 10
Page 8
3 Handling
3.1 Assembly
Handling
Insert radio receiver into the bracket of the control.
Create plug connection from radio receiver to control.
Radio receiver 8 from 10
Page 9
3.2 Commissioning
Programming
Press programming button briefly.
The LED blinks once.
ð
Handling
Deleting memory
Press the flush button of the radio transmitter to be programmed
within 30 seconds.
In the case of dual volume radio transmitters, push one of the two
flush buttons.
The LED blinks three times.
ð
Repeat the process to program additional transmitters (maximum 32
per receiver).
Keep programming button pressed for approx. 8 seconds.
The LED blinks twice.
ð
Release programming button.
The radio receiver's memory has been deleted.
ð
Radio receiver 9 from 10
Page 10
3.3 Disposal
Handling
Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.
Radio receiver 10 from 10
Loading...