Viega 8326.1, 8327.1 Instructions For Use Manual

Flush plate Visign for Public 1

Instructions for Use

for concealed cistern 2H, concealed cistern 2L, concealed cis­tern 2C, concealed cistern Standard 2S

Model Year built:

8326.1 from 01/2011

en_INT

Flush plate Visign for Public 1 2 from 20

Table of contents

1 About these instructions for use 4

Table of contents

1.1

1.2

1.3

Target groups 4
Labelling of notes 4
About this translated version 5

2 Product information 6

2.1

2.1.1

2.2

2.2.1

2.2.2

Intended use 6
Areas of use 6
Product description 7
Overview 7
Technical data 7

3 Handling 8

3.1

3.1.1

3.2

3.2.1

3.2.2

3.2.3

3.3

3.3.1

3.4

3.5

3.5.1

3.6

Assembly information 8
Required material and tools 8
Assembly 8
Prepare cistern 8
Mount flush actuation 14
Mounting the flush plate 17
Commissioning 19
Setting the flush 19
Error, faults and remedy 19
Care and maintenance 20
Maintenance tips 20
Disposal 20

Flush plate Visign for Public 1 3 from 20

About these instructions for use

1 About these instructions for use

Trade mark rights exist for this document, further information can be
found at

1.1 Target groups

The information in this instruction manual is directed at the following
groups of people:

n Heating and sanitary professionals and trained personnel
n Consumers

It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, service this product. This
restriction does not extend to possible operating instructions.

viega.com/legal

.

1.2 Labelling of notes

The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.

Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.

DANGER!
This symbol warns against possible life-threatening injury.

WARNING!
This symbol warns against possible serious injury.

CAUTION!
This symbol warns against possible injury.

NOTICE!
This symbol warns against possible damage to property.

Notes give you additional helpful tips.

Flush plate Visign for Public 1 4 from 20

1.3 About this translated version

This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).

Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The pertinent national laws, stand­ards, regulations and guidelines, as well as other technical guidelines,
have priority over German/European guidelines in this manual: The
information is not binding for other countries and territories and should,
as mentioned, be considered as support.

About these instructions for use

Flush plate Visign for Public 1 5 from 20

2 Product information

2.1 Intended use

2.1.1 Areas of use

Suitable cisterns

The flush plate is intended for the actuation of flushes on Viega con­cealed cisterns.

Installation is only possible in the following Viega concealed cisterns:

n Cistern model 2H
n Cistern model 2L

Ascertain which model is installed before mounting. The following infor­mation will help you to determine the model of the cistern installed:

Cistern 2H

Product information

The revision shaft of this cistern is found at a height of approx. 1 metre
on the front.

Cistern 2L
The revision shaft of this cistern is either found at a height of approx.

75 cm on the front or on the top.

Flush plate Visign for Public 1 6 from 20

2.2 Product description

1 2 3 4

5

2.2.1 Overview

Product information

2.2.2 Technical data

Flush volume

Fig. 1: Component overview

1 - basic panel
2 - holding panel
3 - flush plate with fixing screws
4 - actuating rod
5 - threaded bolt

The product exhibits the following technical data:

A flush with the large flush volume is always released via the flush plate.
The flush volume is approx. 6–9 litres.

For the setting of the flush see

on page 19

.

Ä Chapter 3.3.1 „Setting the flush“

Flush plate Visign for Public 1 7 from 20

3 Handling

3.1 Assembly information

3.1.1 Required material and tools

Tool

The following tools are required for mounting:

n flat screwdriver
n Torx screwdriver (T 10)
n knife (cutter)

3.2 Assembly

Handling

3.2.1 Prepare cistern

The following work stages and diagrams differ depending
on the cistern being used. The relevant steps are marked
accordingly.

Requirements:

n The cistern is fitted into the front wall.
n The front wall is tiled.

Cut into shaft cover.

Flush plate Visign for Public 1 8 from 20

Handling

Remove shaft cover.

Score the revision shaft along the edge of the tiles with a knife.
Angle the knife to do this so that the cut is made flush to the surface

of the wall.

Cut the corners of the revision shaft vertically through to the wall
surface.

Bend out and pull down the sides of the revision shaft.
The edge of the revisions shaft must be flush with the wall surface.

Flush plate Visign for Public 1 9 from 20

Handling

Remove cistern cover.
Remove and keep the threaded bolts from the cistern cover.
Keep cistern casing.

INFO! Only for assembly of the flush plate in cistern 2H or on the
front of cistern 2L.

Press the bow backwards from the mounting of the mechanism.

INFO! Only for assembly of the flush plate on the top of cistern
2L.

Press the bow backwards from the mounting of the mechanism.

Turn the mechanism's lock by 90° in an anti-clockwise direction.

The mechanism is unlocked and can be removed.

ð

Flush plate Visign for Public 1 10 from 20

Flush pipelines (cistern 2H)

Handling

Remove and keep mechanism.

Requirements:

n The revision shaft is shortened in such a way that it is flush with the

surface.

n Mechanism has been removed.

Close corner valve.

Loosen flexible hose on the filling valve (SW 19).

Flush plate Visign for Public 1 11 from 20

Open the corner valve for a few seconds to rinse the pipe.
Re-close corner valve.

Connect the flexible hose onto the filling valve (SW 19).

Handling

Open corner valve.

Flush plate Visign for Public 1 12 from 20

Flush pipelines (cistern 2L)

Handling

Requirements:

n The revision shaft is shortened in such a way that it is flush with the

upper edge of the tiles.

n Mechanism has been removed.

Close corner valve.

Loosen flexible hose on the filling valve (SW 19).

Open the corner valve for a few seconds to rinse the pipe.
Re-close corner valve.

Flush plate Visign for Public 1 13 from 20

Connect the flexible hose onto the filling valve.

Open corner valve.

Handling

3.2.2 Mount flush actuation

Mount mechanism (cistern 2H)

Hang the mechanism in the bow of the drain valve.

Flush plate Visign for Public 1 14 from 20

Insert mechanism.
The mechanism must sit exactly in the recesses in the cistern.

Turn the mechanism's lock by 90° in a clockwise direction.

The mechanism is locked.

ð

Handling

Mount mechanism (cistern 2L)

Vertical installation (flush plate
on the front of the cistern)

How to install the mechanism depends on whether the flush
plate is to be fitted to the front or top of the cistern.

–

Vertical installation (flush plate on the front of the cistern)

–

Horizontal installation (flush plate on the top of the cis­tern)

Hang the mechanism in the bow of the drain valve.

Flush plate Visign for Public 1 15 from 20

Insert mechanism.
The mechanism must sit exactly in the recesses in the cistern.

Turn the mechanism's lock by 90° in a clockwise direction.

The mechanism is locked.

ð

Handling

Horizontal installation (flush
plate on the top of the cistern)

Hang the mechanism in the bow of the drain valve.

Flush plate Visign for Public 1 16 from 20

Handling

Insert mechanism.
In doing so, ensure that the tracks on the top and bottom edge of

the mechanism are in the indentations in the revision shaft of the
cistern.

Turn the mechanism's lock by 90° in a clockwise direction.

The mechanism is locked.

ð

3.2.3 Mounting the flush plate

Requirements:

n The flush actuation has been mounted.

Re-mount cistern casing.

Flush plate Visign for Public 1 17 from 20

Handling

Insert the threaded bolts so deeply that the upper edge of the
threaded bolt sticks out approx. 15 mm behind the upper edge of
the tiles.

Secure threaded bolts with a 90° turn.

Screw actuating rod into the tapped hole.

Set the screw-in depth flush with the upper edge of the tiles with the
help of the template supplied.

Screw on basic panel.

Flush plate Visign for Public 1 18 from 20

Mount holding plates and basic panels.

Mount and screw flush plate tight.

Handling

3.3 Commissioning

3.3.1 Setting the flush

Set the flush volume on the drain valve of the cistern.
Large flush volume: approx. 6–9 litres

3.4

Error Cause Remedy

WC does not flush Cistern is not yet completely full Wait until the cistern is sufficiently

Error, faults and remedy

No water in cistern, corner valve is
closed

full

Open corner valve

WC flush runs through Dirty seal in filling valve Check seal, replace if necessary

Flush plate Visign for Public 1 19 from 20

Error Cause Remedy

Dirty seal in drain valve Check seal, replace if necessary

Handling

WC flush actuation does not work The mechanism is not connected

to the bow

3.5 Care and maintenance

3.5.1 Maintenance tips

Normal soap or a mild cleaning agent can be used for regular care and
prevention of lime scale on the flush plate. Under no circumstances
should scouring agent or scratching objects be used.

Strong stains can be removed using typical household cleaner. Rinse
the detergent thoroughly with clear water after the prescribed exposure
time. There should be no residue on the components.

3.6 Disposal

Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.

Hang the mechanism in the bow

Flush plate Visign for Public 1 20 from 20