Viega 8315.1 Instructions For Use Manual

for concealed cistern 2H, concealed cistern 2L, concealed cis­tern 2C, concealed cistern Standard 2S

Model Year built:

8315.1 from 07/2007

en_INT

Flush plate Visign for Style 10

Instructions for Use

Flush plate Visign for Style 10 2 from 20

Table of contents

1 About these instructions for use 4

1.1

Target groups 4

1.2

Labelling of notes 4

1.3

About this translated version 5

2 Product information 6

2.1

Intended use 6

2.1.1

Areas of use 6

2.2

Product description 7

2.2.1

Overview 7

2.2.2

Technical data 7

3 Handling 8

3.1

Assembly information 8

3.1.1

Required material and tools 8

3.2

Assembly 8

3.2.1

Prepare cistern 8

3.2.2

Mount flush actuation 14

3.2.3

Mounting the flush plate 17

3.3

Commissioning 19

3.3.1

Setting the flush 19

3.4

Error, faults and remedy 19

3.5

Care and maintenance 19

3.5.1

Maintenance tips 19

3.6

Disposal 20

Table of contents

Flush plate Visign for Style 10 3 from 20

1 About these instructions for use

Trade mark rights exist for this document, further information can be
found at www.viega.com/legal-notices.

1.1 Target groups

The information in this instruction manual is directed at the following
groups of people:

n Heating and sanitary professionals and trained personnel
n Consumers

It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, service this product. This
restriction does not extend to possible operating instructions.

The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.

1.2 Labelling of notes

Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.

DANGER!
This symbol warns against possible life-threatening injury.

WARNING!
This symbol warns against possible serious injury.

CAUTION!
This symbol warns against possible injury.

NOTICE!
This symbol warns against possible damage to property.

Notes give you additional helpful tips.

About these instructions for use

Flush plate Visign for Style 10 4 from 20

1.3 About this translated version

This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).

Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The pertinent national laws, stand­ards, regulations and guidelines, as well as other technical guidelines,
have priority over German/European guidelines in this manual: The
information is not binding for other countries and territories and should,
as mentioned, be considered as support.

About these instructions for use

Flush plate Visign for Style 10 5 from 20

2 Product information

2.1 Intended use

2.1.1 Areas of use

The flush plate is intended for the actuation of flushes on Viega con­cealed cisterns.

Installation is only possible in the following Viega concealed cisterns:

n Cistern model 2H
n Cistern model 2L

Ascertain which model is installed before mounting. The following infor­mation will help you to determine the model of the cistern installed:

Cistern 2H
The revision shaft of this cistern is found at a height of approx. 1 metre

on the front.

Cistern 2L
The revision shaft of this cistern is either found at a height of approx.

75 cm on the front or on the top.

Suitable cisterns

Product information

Flush plate Visign for Style 10 6 from 20

2.2 Product description

2.2.1 Overview

1 2 3 4

5

Fig. 1: Component overview

1 - flush plate
2 - support
3 - basic panel
4 - actuating rod
5 - threaded bolt

2.2.2 Technical data

The product exhibits the following technical data:

The flush volume for the flushes are:

n Small flush volume: approx. 3–4 litres
n Large flush volume: approx. 6–9 litres

For the setting of the flush see

Ä Chapter 3.3.1 „Setting the flush“

on page 19

.

Flush volume

Product information

Flush plate Visign for Style 10 7 from 20

3 Handling

3.1 Assembly information

3.1.1 Required material and tools

The following tools are required for mounting:

n flat screwdriver
n knife (cutter)

3.2 Assembly

3.2.1 Prepare cistern

The following work stages and diagrams differ depending
on the cistern being used. The relevant steps are marked
accordingly.

Requirements:

n The cistern is fitted into the front wall.
n The front wall is tiled.

Cut into shaft cover.

Remove shaft cover.

Tool

Handling

Flush plate Visign for Style 10 8 from 20

Score the revision shaft along the edge of the tiles with a knife.
Angle the knife to do this so that the cut is made flush to the surface

of the wall.

Cut the corners of the revision shaft vertically through to the wall
surface.

Bend out and pull down the sides of the revision shaft.
The edge of the revisions shaft must be flush with the wall surface.

Remove cistern cover.
Remove and keep the threaded bolts from the cistern cover.
Keep cistern casing.

Handling

Flush plate Visign for Style 10 9 from 20

INFO! Only for assembly of the flush plate in cistern 2H or on the
front of cistern 2L.

Press the bow backwards from the mounting of the mechanism.

INFO! Only for assembly of the flush plate on the top of cistern
2L.

Press the bow backwards from the mounting of the mechanism.

Turn the mechanism's lock by 90° in an anti-clockwise direction.

ð

The mechanism is unlocked and can be removed.

Remove and keep mechanism.

Handling

Flush plate Visign for Style 10 10 from 20

Requirements:

n The revision shaft is shortened in such a way that it is flush with the

surface.

n Mechanism has been removed.

Close corner valve.

Loosen flexible hose on the filling valve (SW 19).

Open the corner valve for a few seconds to rinse the pipe.
Re-close corner valve.

Flush pipelines (cistern 2H)

Handling

Flush plate Visign for Style 10 11 from 20

Connect the flexible hose onto the filling valve (SW 19).

Open corner valve.

Requirements:

n The revision shaft is shortened in such a way that it is flush with the

upper edge of the tiles.

n Mechanism has been removed.

Close corner valve.

Flush pipelines (cistern 2L)

Handling

Flush plate Visign for Style 10 12 from 20

Loosen flexible hose on the filling valve (SW 19).

Open the corner valve for a few seconds to rinse the pipe.
Re-close corner valve.

Connect the flexible hose onto the filling valve.

Open corner valve.

Handling

Flush plate Visign for Style 10 13 from 20

3.2.2 Mount flush actuation

Hang the mechanism in the bow of the drain valve.

Insert mechanism.
The mechanism must sit exactly in the recesses in the cistern.

Turn the mechanism's lock by 90° in a clockwise direction.

ð

The mechanism is locked.

How to install the mechanism depends on whether the flush
plate is to be fitted to the front or top of the cistern.

–

Vertical installation (flush plate on the front of the cistern)

–

Horizontal installation (flush plate on the top of the cis­tern)

Mount mechanism (cistern 2H)

Mount mechanism (cistern 2L)

Handling

Flush plate Visign for Style 10 14 from 20

Hang the mechanism in the bow of the drain valve.

Insert mechanism.
The mechanism must sit exactly in the recesses in the cistern.

Turn the mechanism's lock by 90° in a clockwise direction.

ð

The mechanism is locked.

Vertical installation (flush plate
on the front of the cistern)

Horizontal installation (flush
plate on the top of the cistern)

Handling

Flush plate Visign for Style 10 15 from 20

Hang the mechanism in the bow of the drain valve.

Insert mechanism.
In doing so, ensure that the tracks on the top and bottom edge of

the mechanism are in the indentations in the revision shaft of the
cistern.

Turn the mechanism's lock by 90° in a clockwise direction.

ð

The mechanism is locked.

Handling

Flush plate Visign for Style 10 16 from 20

3.2.3 Mounting the flush plate

Requirements:

n The flush actuation has been mounted.

Re-mount cistern casing.

Insert the threaded bolts so deeply that the upper edge of the
threaded bolt sticks out approx. 20 mm behind the upper edge of
the tiles.

Secure threaded bolts with a 90° turn.

Screw on basic panel.

20

20

Handling

Flush plate Visign for Style 10 17 from 20

Screw the actuating rods into the threaded holes of the mechanism.

Set the upper actuating rod flush with the basic panel. If necessary,
shorten the actuating rod on the thread with a cutting knife.

Set the lower actuating rod flush with the basic panel. If necessary,
shorten the actuating rod on the thread with a cutting knife.

Insert support in the basic panel.

Handling

Flush plate Visign for Style 10 18 from 20

Place and press the flush plate onto the basic panel.

3.3 Commissioning

3.3.1 Setting the flush

Set the flush volume on the drain valve of the cistern.
Small flush volume (above): approx. 3–4 litres
Large flush volume (below): approx. 6–9 litres

3.4 Error, faults and remedy

Error Cause Remedy

WC does not flush Cistern is not yet completely full Wait until the cistern is sufficiently

full

No water in cistern, corner valve is
closed

Open corner valve

WC flush runs through Dirty seal in filling valve Check seal, replace if necessary

Dirty seal in drain valve Check seal, replace if necessary

WC flush actuation does not work The mechanism is not connected

to the bow

Hang the mechanism in the bow

3.5 Care and maintenance

3.5.1 Maintenance tips

Normal soap or a mild cleaning agent can be used for regular care and
prevention of lime scale on the flush plate. Under no circumstances
should scouring agent or scratching objects be used.

Handling

Flush plate Visign for Style 10 19 from 20

Strong stains can be removed using typical household cleaner. Rinse
the detergent thoroughly with clear water after the prescribed exposure
time. There should be no residue on the components.

3.6 Disposal

Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.

Handling

Flush plate Visign for Style 10 20 from 20