How it Works
Viega
Loading...
8142

Viega 8142, Eco Plus Instructions For Use Manual

Download
Page 1
for WB with single-hole fitting Model Year built:
8142 from 09/2005
en_INT
Viega Eco Plus washbasin corner element
Instructions for Use
Page 2
Page 3
Table of contents
1 About these instructions for use 4
1.1
Target groups 4
1.2
Labelling of notes 4
1.3
About this translated version 5
2 Product information 6
2.1
Standards and regulations 6
2.2
Intended use 6
2.2.1
Areas of use 6
2.3
Product description 7
2.3.1
Overview 7
2.3.2
Compatible components 7
2.3.3
Sound protection 7
2.3.4
Technical data 8
3 Handling 9
3.1
Assembly information 9
3.1.1
Mounting conditions 9
3.1.2
Installation dimensions 9
3.1.3
Required tools 9
3.2
Assembly 11
3.2.1
Mounting element 11
3.3
Disposal 24
Table of contents
Page 4
1 About these instructions for use
Trade mark rights exist for this document, further information can be found at
viega.com/legal
.
1.1 Target groups
The information in this instruction manual is directed at the following groups of people:
n Heating and sanitary professionals and trained personnel n Drywall builder
It is not permitted for individuals without the abovementioned training or qualification to mount, install and, if required, maintain this product. This restriction does not extend to possible operating instructions.
The installation of Viega products must take place in accordance with the general rules of engineering and the Viega instructions for use.
1.2 Labelling of notes
Warning and advisory texts are set aside from the remainder of the text and are labelled with the relevant pictographs.
DANGER! This symbol warns against possible life-threatening injury.
WARNING! This symbol warns against possible serious injury.
CAUTION! This symbol warns against possible injury.
NOTICE! This symbol warns against possible damage to property.
Notes give you additional helpful tips.
About these instructions for use
Page 5
1.3 About this translated version
This instruction for use contains important information about the choice of product or system, assembly and commissioning as well as intended use and, if required, maintenance measures. The information about the products, their properties and application technology are based on the current standards in Europe (e. g. EN) and/or in Germany (e. g. DIN/DVGW).
Some passages in the text may refer to technical codes in Europe/ Germany. These should serve as recommendations in the absence of corresponding national regulations. The relevant national laws, stand­ards, regulations, directives and other technical provisions take priority over the German/European directives specified in this manual: The information herein is not binding for other countries and regions; as said above, they should be understood as a recommendation.
About these instructions for use
Page 6
2 Product information
2.1 Standards and regulations
The following standards and regulations apply to Germany / Europe. National regulations can be found on the relevant web site of your country at
viega.com/standards
.
Regulations from section: Fields of application / Mounting conditions
Scope / Notice Regulations applicable in Ger-
many
suitable masonry walls EN 1996-1-1
suitable concreted walls DIN 1045
suitable support profiles DIN 18183
Regulations from section: Sound protection
Scope / Notice Regulations applicable in Ger-
many
Fulfilled noise protection require­ments
DIN 4109
Fulfilled noise protection require­ments
DIN 4109 (additional sheet 2)
Fulfilled noise protection require­ments
VDI 4100 SSt I-SSt II
2.2 Intended use
2.2.1 Areas of use
The Viega Eco Plus washbasin element is suitable for mounting on masonry wall constructions and support profiles pursuant to the regula­tions in section
Ä „Regulations from section: Fields of application /
Mounting conditions“ on page 6
.
Product information
Page 7
2.3 Product description
2.3.1 Overview
3
4
5
6
7
1
2
Fig. 1: Components and scope of delivery
1 - Viega Eco Plus element 2 - adjusting screws 3 - threaded bolt 4 - mounting bracket for drain elbow 5 - connections for wall plates 6 - drain elbow 7 - adjustable feet
2.3.2 Compatible components
The element is compatible with all common washbasin ceramics, even with larger projection (barrier-free).
2.3.3
Sound protection
The washbasin element complies with the noise insulation requirements specified in section
Ä „Regulations from section: Sound protection“
on page 6
.
Product information
Page 8
2.3.4 Technical data
The product has the following technical data:
drain elbow DN 40 / 50
Rubber nipple DN 40 / 30
Construction height 980 mm–1130 mm
Product information
Page 9
3 Handling
3.1 Assembly information
3.1.1 Mounting conditions
The element is suitable for mounting on masonry wall constructions and support profiles pursuant to the regulations in section
Ä „Regulations
from section: Fields of application / Mounting conditions“ on page 6
.
The element may only be mounted on even wall surfaces.
With the construction height, the marked height of the upper edge of the finished floor must be observed.
3.1.2 Installation dimensions
Fig. 2: Dimensions
3.1.3 Required tools
The following tools are required for mounting the washbasin element:
Suitable walls
Construction height
Handling
Page 10
n drill with 10 mm drill bit n ratchet with sockets: 13 mm / 17 mm n fork or ring spanner: 13 mm / 17 mm
Handling
Viega Eco Plus washbasin corner element 10 from 24
Page 11
3.2 Assembly
3.2.1 Mounting element
980 - 1130
Position the element at construction height. The element can be adjusted continuously from 980–1130 mm. Align element. Mark drill holes.
Mounting in a corner (approx. 90°)
Handling
Viega Eco Plus washbasin corner element 11 from 24
Page 12
980 - 1130
Drill holes for the wall fixing and the floor supports. Hit dowel (10 mm) into the wall/floor.
Handling
Viega Eco Plus washbasin corner element 12 from 24
Page 13
Screw the element into the wall and into the floor (SW 13 / 17).
Handling
Viega Eco Plus washbasin corner element 13 from 24
Page 14
Connect water and wastewater pipe. Clad the element with a single layer of IFGP cladding panels
(1 x 12.5 mm).
Handling
Viega Eco Plus washbasin corner element 14 from 24
Page 15
980 - 1130
Position the element at construction height. The element can be adjusted continuously from 980–1130 mm. Remove the floor support where the drainage line is. Align element. Mark drill holes (5 wall fixings and one floor support).
Mounting in the corner (approx. 90°) with cladding of the drainage line
Handling
Viega Eco Plus washbasin corner element 15 from 24
Page 16
980 - 1130
Drill holes for the wall fixing and the floor support. Hit dowel (10 mm) into the wall/floor.
Handling
Viega Eco Plus washbasin corner element 16 from 24
Page 17
Screw the element into the wall and into the floor (SW 13 / 17).
Handling
Viega Eco Plus washbasin corner element 17 from 24
Page 18
Connect water and wastewater pipe. Clad the element with a single layer of IFGP cladding panels
(1 x 12.5 mm).
Handling
Viega Eco Plus washbasin corner element 18 from 24
Page 19
980 - 1130
Position the element at construction height. The element can be adjusted continuously from 980–1130 mm. Align element. Mark drill holes (4 wall fixings and two floor supports).
Mounting on the wall (one-sided fixing)
Handling
Viega Eco Plus washbasin corner element 19 from 24
Page 20
980 - 1130
Drill holes for the wall fixing and the floor support. Hit dowel (10 mm) into the wall and the floor.
Handling
Viega Eco Plus washbasin corner element 20 from 24
Page 21
Screw the element into the wall and into the floor (SW 13).
Handling
Viega Eco Plus washbasin corner element 21 from 24
Page 22
Connect water and wastewater pipe. Clad the element with a single layer of IFGP cladding panels
(1 x 12.5 mm).
Handling
Viega Eco Plus washbasin corner element 22 from 24
Page 23
Position the elements at construction height. The element can be adjusted continuously from 980–1130 mm. Align elements. Mark drill holes (each 4 wall fixings and two floor supports). Drill holes for the wall fixing and the floor supports. Hit dowel (10 mm) into the wall and the floor. Screw elements into the wall, into the floor and together (SW 13). Connect water and wastewater pipe. Clad the corner elements with a single layer of IFGP cladding panels
(1 x 12.5 mm).
Line mounting of corner elements
Handling
Viega Eco Plus washbasin corner element 23 from 24
Page 24
Position the element at construction height. The element can be adjusted continuously from 980–1130 mm. Align element. Mark drill holes (4 wall fixings and two floor supports). Drill holes for the wall fixing and the floor support. Hit dowel (10 mm) into the wall and the floor. Screw the element into the wall and into the floor (SW 13). Connect water and wastewater pipe. Clad the element with a single layer of IFGP cladding panels
(1 x 12.5 mm).
3.3
Disposal
Separate the product and packaging materials (e. g. paper, metal, plastic or non-ferrous metals) and dispose of in accordance with valid national legal requirements.
Mounting in a corner > 90°
Handling
Viega Eco Plus washbasin corner element 24 from 24
Loading...
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use