Viega 8133.3 Instructions For Use Manual

Washbasin module

Instructions for Use

for barrier-free washbasins
Model Year built:

8133.3 from 03/2009

en_INT

Washbasin module 2 from 13

Table of contents

1 About these instructions for use 4

Table of contents

1.1

1.2

1.3

Target groups 4
Labelling of notes 4
About this translated version 5

2 Product information 6

2.1

2.2

2.2.1

2.3

2.3.1

2.3.2

2.3.3

2.3.4

2.4

Standards and regulations 6
Intended use 6
Areas of use 6
Product description 7
Overview 7
Compatible components 7
Sound protection 7
Technical data 8
Accessories and spare parts 8

3 Handling 9

3.1

3.1.1

3.1.2

3.1.3

3.2

3.2.1

3.2.2

3.3

Assembly information 9
Mounting conditions 9
Installation dimensions 9
Required tools 9
Assembly 10
Mounting module 10
Rounding off jobs 13
Disposal 13

Washbasin module 3 from 13

About these instructions for use

1 About these instructions for use

Trade mark rights exist for this document, further information can be
found at

1.1 Target groups

The information in this instruction manual is directed at the following
groups of people:

n Heating and sanitary professionals and trained personnel
n Drywall builder

It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.

viega.com/legal

.

1.2 Labelling of notes

The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.

Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.

DANGER!
This symbol warns against possible life-threatening injury.

WARNING!
This symbol warns against possible serious injury.

CAUTION!
This symbol warns against possible injury.

NOTICE!
This symbol warns against possible damage to property.

Notes give you additional helpful tips.

Washbasin module 4 from 13

1.3 About this translated version

This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).

Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand­ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.

About these instructions for use

Washbasin module 5 from 13

2 Product information

2.1 Standards and regulations

The following standards and regulations apply to Germany / Europe.
National regulations can be found on the relevant web site of your
country at

Regulations from section: Fields of application / Mounting conditions

Scope / Notice Regulations applicable in Ger-

suitable masonry walls EN 1996-1-1

suitable concreted walls DIN 1045

viega.com/standards

Product information

.

many

2.2 Intended use

2.2.1 Areas of use

suitable support profiles DIN 18183

Regulations from section: Sound protection

Scope / Notice Regulations applicable in Ger-

many

Fulfilled noise protection require­ments

Fulfilled noise protection require­ments

Fulfilled noise protection require­ments

The Viega washbasin module is suitable for mounting on wall construc­tions pursuant to the regulations in section

Fields of application / Mounting conditions“ on page 6

for use in a Steptec pre-wall construction.

DIN 4109

DIN 4109 (additional sheet 2)

VDI 4100 SSt I-SSt II

Ä „Regulations from section:

and is intended

Washbasin module 6 from 13

2.3 Product description

2.3.1 Overview

Product information

Fig. 1: Components and scope of delivery

1 - washbasin module
2 - threaded bolt
3 - connections for wall plates
4 - concealed siphon

2.3.2 Compatible components

The module is compatible with all common washbasin ceramics, even
with larger projection (barrier-free).

2.3.3

Sound protection

The washbasin module complies with the noise insulation requirements
specified in section

on page 6

Ä „Regulations from section: Sound protection“

.

Washbasin module 7 from 13

2.3.4 Technical data

The product has the following technical data:

drain elbow DN 40 / 50

Rubber nipple DN 40 / 30

2.4 Accessories and spare parts

Required accessories

The fixing set model 8173 is required to secure.

Product information

For Keramag washbasin models

You require a concealed odour trap.
Available models

n Model 5633.1 (chrome-plated cover plate)
n Model 5633.2 (white cover plate)

The suitable drain for the following washbasin models must be ordered
from Keramag.

Keramag wash­basin model

Keramag model
No.

Paracelsus Vitalis Dejuna

521 323 521 323 521 423

Washbasin module 8 from 13

3 Handling

3.1 Assembly information

3.1.1 Mounting conditions

Suitable walls

For this, observe the Steptec system instructions for use.

Construction height

With the construction height, the marked height of the upper edge of
the finished floor must be observed.

Handling

3.1.2 Installation dimensions

Fig. 2: Dimensions

A - adjustable height

3.1.3 Required tools

The following tools are required for mounting the washbasin module:

Washbasin module 9 from 13

3.2 Assembly

3.2.1 Mounting module

Mounting in Steptec

Securing module

Handling

n ratchet with sockets: 13 mm / 17 mm
n fork or ring spanner: 17 mm / 19 mm
n Phillips-tip screwdriver

The two vertical rails, which surround the module, must be
open towards the module and be at an interval of 430 mm.

Secure the module onto the open Steptec rail with the slot nuts sup­plied:

Insert the slot nut into the opening of the module.

Push the slot nut in slightly.
Turn by 90°.

The slot nut is secured in the Steptec rail.

ð

Washbasin module 10 from 13

Align the height of the module.
Tighten the slot nut with a ring spanner (SW 17).

Tighten the other slot nuts in the same way.

The module is secured on the rail framework.

ð

Handling

Set desired height of the module (X). When doing so, observe the
upper edge of the finished floor.

Attach the concealed siphon with the screws attached.

Washbasin module 11 from 13

Handling

Set height of fitting connection panel.
To do this, loosen the lateral screws and choose the desired height.
Re-tighten screws.

Remove the site protection.
Check pipe position and, if necessary, set the required sizes.
Subsequent adjustment is possible.
Replace the site protection.

Attach bracket for threaded bolts:
Insert bracket horizontally and turn clockwise by 90°.
The distance between the brackets may only be a maximum of

390 mm.
Screw in threaded bolt and tighten with a ring spanner (SW 17).

Set the connections for wall plates. The interval between the con­nections bolts can be set to 226 or 306 mm.

Washbasin module 12 from 13

Fig. 3: Installation dimensions, concealed
siphon with ceramic

3.2.2 Rounding off jobs

Handling

Observe highest and lowest sizes.
Observe the ceramic manufacturer's instructions for additional

sizes.

3.3

Single clad pre-wall: Clad with 12.5 mm wide IFGP or 12 mm wide
Aqua-KS cladding panels.

When doing so, make sure that no abutting edges converge.
Grout the abutting edges and joints with a suitable filler.
Observe the instruction manual for the cladding panels for more

information.

Disposal

Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.

Washbasin module 13 from 13