Viega 8127.3 Instructions For Use Manual

Urinal module

Instructions for Use

for "Joly" and "Visit" (Keramag) urinal, connection of the Visign
equipment set (manual and touchless flush actuation)

Model Year built:

8127.3 from 03/2009

en_INT

Urinal module 2 from 15

Table of contents

1 About these instructions for use 4

Table of contents

1.1

1.2

1.3

Target groups 4
Labelling of notes 4
About this translated version 5

2 Product information 6

2.1

2.2

2.2.1

2.3

2.3.1

2.3.2

2.3.3

2.3.4

Standards and regulations 6
Intended use 6
Areas of use 6
Product description 7
Overview 7
Compatible components 7
Sound protection 8
Technical data 8

3 Handling 9

3.1

3.1.1

3.1.2

3.2

3.2.1

3.2.2

3.3

Assembly information 9
Mounting conditions 9
Required tools 9
Assembly 9
Mounting module 9
Rounding off jobs 15
Disposal 15

Urinal module 3 from 15

About these instructions for use

1 About these instructions for use

Trade mark rights exist for this document, further information can be
found at

1.1 Target groups

The information in this instruction manual is directed at the following
groups of people:

n Heating and sanitary professionals and trained personnel

It is not permitted for individuals without the abovementioned training or
qualification to mount, install and, if required, maintain this product. This
restriction does not extend to possible operating instructions.

viega.com/legal

.

1.2 Labelling of notes

The installation of Viega products must take place in accordance with
the general rules of engineering and the Viega instructions for use.

Warning and advisory texts are set aside from the remainder of the text
and are labelled with the relevant pictographs.

DANGER!
This symbol warns against possible life-threatening injury.

WARNING!
This symbol warns against possible serious injury.

CAUTION!
This symbol warns against possible injury.

NOTICE!
This symbol warns against possible damage to property.

Notes give you additional helpful tips.

Urinal module 4 from 15

1.3 About this translated version

This instruction for use contains important information about the choice
of product or system, assembly and commissioning as well as intended
use and, if required, maintenance measures. The information about the
products, their properties and application technology are based on the
current standards in Europe (e. g. EN) and/or in Germany
(e. g. DIN/DVGW).

Some passages in the text may refer to technical codes in Europe/
Germany. These should serve as recommendations in the absence of
corresponding national regulations. The relevant national laws, stand­ards, regulations, directives and other technical provisions take priority
over the German/European directives specified in this manual: The
information herein is not binding for other countries and regions; as said
above, they should be understood as a recommendation.

About these instructions for use

Urinal module 5 from 15

2 Product information

2.1 Standards and regulations

The following standards and regulations apply to Germany / Europe.
National regulations can be found on the relevant web site of your
country at

Regulations from section: Sound protection

Scope / Notice Regulations applicable in Ger-

viega.com/standards

Product information

.

many

2.2 Intended use

2.2.1 Areas of use

Fulfilled noise protection require­ments

Fulfilled noise protection require­ments

Fulfilled noise protection require­ments

The urinal module is designed for mounting in a Steptec pre-wall con­struction.

DIN 4109

DIN 4109 (additional sheet 2)

VDI 4100 SSt I-SSt II

Urinal module 6 from 15

2.3 Product description

2.3.1 Overview

Product information

Fig. 1: Components

1 - urinal installation set
2 - suction moulded piece
3 - connection for Keramag "Joly" and "Visit"

2.3.2 Compatible components

The urinal module is compatible with the urinals "Joly" and "Visit" by
Keramag.

Compatible flush plates

Product

Visign for Style Flush plate Visign for

Name Model

8315.2

Style 10

Flush plate Visign for

8331.2

Style 11

Flush plate Visign for

8332.2

Style 12

Urinal module 7 from 15

Product Name Model

Product information

Flush plate Visign for
Style 13

Flush plate Visign for
Style 14

Visign for More Flush plate Visign for

More 100

Flush plate Visign for
More 102

Flush plate Visign for
More 103

Flush plate Visign for
More 104

Visign for Public Flush plate Visign for

Public

Remote actuation
Visign for Public

Remote actuation
Visign for Public

Cover plate Visign for
Public

8333.2

8334.2

8352.2

8353.2

8355.2

8354.2

8326.2

8326.55

8326.65

8326.7

2.3.3 Sound protection

2.3.4 Technical data

The urinal module complies with the noise insulation requirements
specified in section

on page 6

The product has the following technical data:

drain elbow

Fitting connection Rp ½

Maximum height of urinal inlet
from upper edge of the finished
floor

.

Ä „Regulations from section: Sound protection“

DN 50

n with basic element construc-

tion height 1130 = 880 mm

n with basic element construc-

tion height 1370 = 1120 mm

Urinal module 8 from 15

3 Handling

3.1 Assembly information

3.1.1 Mounting conditions

Construction height

With the construction height, the marked height of the upper edge of
the finished floor must be observed.

Actuation

The actuation takes place via manual flush actuation, connection of the
Visign equipment set.

Handling

3.1.2 Required tools

3.2 Assembly

3.2.1 Mounting module

Mounting in Steptec

Securing module

The following tools are required for mounting the urinal module:

n fork or ring spanner: 17 mm / 19 mm
n Phillips-tip screwdriver

The two vertical rails, which surround the module, must be
open towards the module and be at an interval of 430 mm.

Secure the module onto the open Steptec rail with the slot nuts sup­plied:

Insert the slot nut into the opening of the module.

Urinal module 9 from 15

Push the slot nut in slightly.
Turn by 90°.

The slot nut is secured in the Steptec rail.

ð

Align the height of the module.
Tighten the slot nut with a ring spanner (SW 17).

Handling

Tighten the other slot nuts in the same way.

The module is secured on the rail framework.

ð

Set desired height for the bracket of the drain elbow (X). When doing
so, observe the upper edge of the finished floor.

Urinal module 10 from 15

Make water connection.

Check height settings.
In addition, observe the following details.

Handling

Keramag 'Joly'

Urinal module 11 from 15

Handling

A - The size results from

Urinal module 12 from 15

Handling

Keramag 'Visit'

A - The size results from

Urinal module 13 from 15

Handling

A - The size results from

Urinal module 14 from 15

Handling

3.2.2 Rounding off jobs

3.3

Disposal

A - The size results from

Single clad pre-wall: Clad with 12.5 mm wide IFGP or 12 mm wide
Aqua-KS cladding panels.

When doing so, make sure that no abutting edges converge.
Grout the abutting edges and joints with a suitable filler.
Observe the instruction manual for the cladding panels for more

information.

Separate the product and packaging materials (e. g. paper, metal,
plastic or non-ferrous metals) and dispose of in accordance with valid
national legal requirements.

Urinal module 15 from 15